Air King Fan 9020 User Manual
Contents
1. Ventilation Products OPERATING INSTRUCTIONS amp PARTS MANUAL 20 WALLMOUNT FAN 20 50 8 cm MODEL 9020 READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE INSTALL OPERATE OR MAINTAIN THE PRODUCT DESCRIBED PROTECT YOUR SELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND OR PROPERTY DAMAGE RETAIN INSTRUCTIONS FOR FUTURE REFERENCE DESCRIPTION The Air King 20 50 8 cm wallmount fan features 3 speed pull cord operation and a 3 paddle fan blade This fan has a permanently lubricated motor with a 9 ft 2 74 m 18 3 cord set and is constructed of sturdy powder coated steel SPECIFICATIONS MO1OF secvccecsssvcccievsessesntvaaceceeens 120V 50 60 Hz Blade diameter cseseoee 20 50 8 cm Speeds iranan 3 COMO isis Pull Cord Air flow distribution 360 Approvals isinsin UL ETL Listed Close mesh fan guard meets OSHA requirements GENERAL SAFETY INFORMATION 1 Make certain that the power source conforms to the electrical require ments of the fan 2 The power cord is equipped with a three prong grounded plug that must be inserted into a matching receptacle Under no circumstances should the grounding prong be cut off the plug Where a two prong wall receptacle is encountered it must be replaced with a properly grounded three prong receptacle installed in accordance with the National Electr2. the assembly to assure the Blade is free of all obstructions 6 Plug the power cord into a properly grounded three prong receptacle SECONDARY SUPPORT CABLE 1 Loop one end of cable around the Yoke Figure 5 2 Attach a Cable Clamp with the U on the tail side of the loop leaving a tail approximately 1 to 2 inches Tighten clamp nuts to 32 inch pounds torque forming a tight loop Make sure no part of the cable interferes with the blade Figure 5 3 Wrap the other end of the cable around a secure building joist truss CAUTION USE OF THE SECONDARY SUPPORT CABLE DOES NOT GUARANTEE PROTECTION AGAINST INJURY OF PERSONS MOUNT ING OF BOTH THE CIRCULATOR AND CABLE COULD FAIL IF SUB JECTED TO ABUSE NEGLECT OR IMPROPER INSTALLATION OPERATION 1 Plug in cord and select desired operating speed with pull cord 2 WARNING This fan should be used only in a clean dry environment Mounting of this product in any way other then specified in the instruction sheet will null and void the manufacturer s warranty MAINTENANCE WARNING ALWAYS UNPLUG THE CORD BEFORE SERVICING CLEANING Use a soft cloth and a mild soap solution such as liquid dish washing detergent CAUTION Do not use gasoline benzine thinner harsh cleaners etc which will damage the fan Dry all parts with a soft cloth completely before reconnecting to power supply STORAGE When not in use keep unit in a clean dry place MOTOR IS PERMANENTLY LUBRICATED Figure
3. 4 Figure 5 1 2 Tail Tight Loop In Cable Yoke LIMITED WARRANTY WHAT THIS WARRANTY COVERS This product is warranted against defects in workmanship and or materials HOW LONG THIS WARRANTY LASTS This warranty extends only to the original purchaser of the product and lasts for one 1 year from the date of original purchase or until the original purchaser of the product sells or transfers the product whichever first occurs WHAT AIR KING WILL DO During the warranty period Air King will at its sole option repair or replace any part or parts that prove to be defective or replace the whole product with the same or comparable model WHAT THIS WARRANTY DOES NOT COVER This warranty does not apply if the product was damaged or failed because of accident improper handling or operation shipping damage abuse misuse unauthorized repairs made or attempted This warranty does not cover shipping costs for the return of products to Air King for repair or replacement Air King will pay return shipping charges from Air King following warranty repairs or replacement ANY AND ALLWARRANTIES EXPRESSED OR IMPLIED INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY LAST ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE OR UNTIL THE ORIGINAL PURCHASER OF THE PRODUCT SELLS OR TRANSFERS THE PRODUCT WHICHEVER FIRST OCCURS AND IN NO EVENT SHALL AIR KING S LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY INCLUDE I INCIDENTA
4. L OR CONSEQUENTIAL DAMAGES FROM ANY CAUSE WHATSOEVER OR Il REPLACMENT OR REPAIR OF ANY HOUSE FUSES CIRCUIT BREAKERS OR RECEPTACLES NOTWITHSTANDING ANYTHING TO THE CONTRARY IN NO EVENT SHALL AIR KING S LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY EXCEED THE PURCHASE PRICE OF THE PRODUCT AND ANY SUCH LIABILITY SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIOD Some states and provinces do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so these exclusions or limitations may not apply to you This warranty gives you specific legal rights You may also have other rights which vary from state to state and province to province Proof of purchase is required before a warranty claim will be accepted CUSTOMER SERVICE Toll Free 800 233 0268 Email producthelp laskoproducts com Our Customer Service team is available to assist you with product questions service center locations and replacement parts They can be reached Monday through Friday 8am 5pm Eastern Please have your model number available as well as the type and style located on the underside of your product Please do not return product to place of purchase Customer Service Dept 820 Lincoln Ave West Chester PA 19380 Please do not send product to this location www laskoproducts com PARTS FOR DISCONTINUED OBSOLETE AND CERTAIN OTHER PRODUCTS MAY NOT BE AVAILABLE DUE TO SAFETY REASONS
5. MANY ELECTRONIC COMPONENTS AND MOST HEATER COMPONENTS ARE NOT AVAILABLE TO CONSUMERS FOR INSTALLATION OR REPLACEMENT Rev F 9 07 2 2084796
6. econnecting to power supply WARNING BECAUSE OF SIZE AND WEIGHT OF THIS FAN MAKE SURE ALL PARTS ARE COMPLETELY ASSEMBLED ACCORDING TO INSTRUCTIONS FAILURETO DO SO COULD RESULT IN FAN COMING APART DURING OPERATION AND OR PERSONAL INJURY WARNING THIS PLUG IS A SAFETY FEATURE TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK AND PERSONAL INJURY DO NOT Rev F 9 07 WARNING This fan should be used only in a clean dry environment Mounting of this product in any way other then specified in the instruction sheet will null and void the manufacturer s warranty REMOVE REPLACE REPAIR OR TAMPER WITH THE ORIGINALLY SUPPLIED PLUG IF THE FAN DOES NOT FUNCTION PROPERLY IT MAY BE DUE TO THE SAFETY DEVICE INCORPORATED IN THIS PLUG RETURNTO AN AUTHORIZED SERVICE CENTER OR CALL 800 233 0268 MONDAY FRIDAY BETWEEN 8 00 A M AND 5 00 P M EST IF THE PLUG WARNING LABEL IS MISSING OR DAM AGED CALL THE TOLL FREE NUMBER FOR A REPLACEMENT LABEL 9 This Fan is not suitable for use in hazardous locations Please refer to National Electric Code NEC Article 500 or applicable state or local codes or standards relating to electrical requirements for Hazardous locations THIS FAN DOES NOT MEET THE REQUIRMENTS OF NEC ARTICLE 500 2002 WALL CEILING BRACKET INSTALLATION NOTE ALWAYS INSTALL THE BRACKET TO A MINIMUM OF 2 X 4 STUDDING 1 Lay Fan Head on flat surface so the front side is facing down Fi
7. gure 1 Loosely attach one Grill Knob and one Rubber Spacer to the Head Assembly Attach the other Grill Knob and Rubber Spacer to the Head Assembly and FIRMLY tighten Return to the first Grill Knob and FIRMLY tighten Figure 1 2 Locate the wall or ceiling stud nearest to the desired Fan location Following the proper mounting diagram attach the Bracket to the stud using three 3 5 16 diameter x 2 long Lag Screws Not Supplied or appropriately sized Bolts and Nuts if attaching to I beams Wall Mount Assembly Figure 2 Ceiling Mount Assembly Figure 3 Figure 2 Wall Mount Assembly Figure 3 Ceiling Mount Assembly Nut Ceiling Stud a Bracket i Nut Flatwasher Bracket d EN EA SEZ Wall Stud Fan Head 2084796 MODEL 9020 3 Insert Bolt through Yoke Bracket Pivot Hole Flatwasher and into Locknut Figure 2 or Figure 3 4 While holding Fan in the desired position firmly tighten the 7 16 Bolt CAUTION THE SECONDARY SUPPORT CABLE PROVIDED SHOULD BE USED FOR ADDITIONAL SAFETY or other support near the Fan If none of these are available wrap cable around the bracket Figure 4 Take up excess slack in the cable CAUTION USE ONLY THE MOUNTING HARD WARE WHICH IS RECOMMENDED FOR USE ON THIS FAN 4 Attach the remaining Cable Clamp as indicated in step 2 The excess tail should be trimmed to extend 1 to 2 inches past the Clamp 5 Check
8. ical Code NEC and all applicable local codes and ordinances This work must be done only by a qualified electrician using copper wire only WARNING USE OF ATHREE PRONG TO TWO PRONG ADAPTER IS NOT RECOMMENDED IMPROPER CONNECTION MAY CREATE THE RISK OF ELECTRICAL SHOCK USE OF SUCH ADAPTERS IS NOT PERMITTED IN CANADA 3 Where possible avoid the use of extension cords If they must be used minimize the risk of overheating by ensuring that they are UL listed and of the proper gauge and length Never use a single extension cord to operate more than one fan 4 Do not insert fingers or foreign objects into the fan Do not block or tamper with the fan in any manner while it is in operation Do not touch the fan while in operation or just after it has been turned off as some parts may be hot enough to cause injury 5 Unplug power cord before installing or servicing the fan AARNING DO NOT DEPEND UPON THE ON OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN INSTALLING OR SERVICING THE FAN ALWAYS UNPLUG THE POWER CORD 6 This fan is intended for general use ONLY It must NOT be used in potentially dangerous locations such as flammable explosive chemical laden or wet atmospheres WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DONOT USE THIS FAN WITH ANY SOLID STATE SPEED CONTROL DEVICE 7 DO NOT use fan in a window Rain may create an electrical hazard 8 Completely reassemble fan according to instructions before r
Download Pdf Manuals
Related Search