Home

Manual

1. Charger 5VDC outdoor unit 4 black E y Manual unlocking switch e L red NOTES Do not attempt to open modify or repair any part of the camera monitor or its accessories Do not get any part of the monitor or its accessories wet Please keep the monitor away from other electromagnetic items as this can cause interference with the transmission Distributed by TechBrands by Electus Distribution Pty Ltd 320 Victoria Rd Rydalmere NSW 2116 Australia Ph 1300 738 555 Int l 61 2 8832 3200 Fax 1300 738 500 www techbrands com
2. TECH Digital 2 4GHz Wireless Video Doorphone With 3 5 LCD Monitor User Manual Specifications Camera Power Consumption 400mA IP Rating IP55 Resolution 300K Pixels Viewing Angle 120 degrees Input Voltage 5VDC 1A Dimensions 74 W x 134 H x 31 D mm Memory Capacity 2MB approx 100 photos 3 5 LCD Monitor Power Consumption 400mA Frame Rate 25fps Run Time 4 hours continuous Input Voltage 5VDC 1A Dimensions 84 W x 126 H x 20 D mm Flyout Rain Shield Camera Infrared PIR Speaker LED Indicator Call Button Microphone Speaker Connector Power Standby Lock Unlock Button Reset Button Battery Cover F Battery Cover Outdoor Camera Installation Instructions 1 Choose a spot to install the outdoor camera Ideally choose a position 1 4 1 7m above the ground and avoid facing the camera directly at the sun Ensure that the camera lens and PIR sensor faces out towards the path of entry so that movement up to the door can be captured 2 Drill holes with the dimensions according to the diagram below put the rubber screw plugs in and screw in the rain shield to the wall with the screws supplied 3 Feed the charger through the hole in the rain shield and connect the charger according to the wiring diagram the unit will start up automatically Wire connector of outdoor unit Charger 5VDC outdoor unit 4 To insert the camera into the rain
3. is the setting for the door to automatically lock when door lock controls available separately have been installed To unlock the door press the ON OFF Switch key once in intercom mode Press the T V key to adjust the time of the lock delay the range of the time is 1 6 seconds Press the OK key to confirm and return to standby mode PIR Setting When the PIR detects movement within its detection range the signal shall be sent to the monitor to activate the screen and capture a photo After the photo is taken the camera and monitor will both return to standby mode When the screen is lit on the monitor press the OK key to intercom When the camera has been set up to multiple monitors maximum of 3 monitors the PIR function can be switched on or off through the menu of each monitor but only one monitor will light up when there is movement detected by the PIR On the monitor that the the PIR is activated a red PIR symbol will show on the top of the screen Press the T V key to choose ON or OFF Press the OK or FUNC key to confirm your selection and the setting shall be transmitted to the outdoor camera Outdoor Camera CALL Monitor Function Press the Doorbell key to call the backlight of the button will light up and a ringing sound will be heard The screen of the monitor will show the image and the unit will ring for a maximum of 30 seconds If the call is not acce
4. pted on the monitor the camera will stop ringing and a recall will be allowed Intercom when ringing Press the OK button on the monitor to activate intercom mode the maximum intercom time is 90 seconds To take a photo during intercom mode press the FUNC key One photo will be taken per press of the button To exit intercom mode press the OK key and the unit will return to standby mode with a beep sound Automatic photo If a call isn t answered within 5 seconds the monitor will take a photo automatically Monitor CALL Outdoor Camera Function Monitoring Mode SAEF In standby mode press the key on the monitor to call the outdoor camera No audio will be heard on the camera as this is monitoring mode To turn it from monitoring mode to two way communication press the OK button the intercom time is 90 seconds To take a photo during intercom mode press the FUNC key One photo will be taken per press of the button To exit monitoring mode press the oo key on the monitor and the unit will return to standby mode To exit intercom mode press the OK key and the unit will return to standby mode Exposure Adjustment If the image is not clear on the monitor the brightness of the monitor is adjustable up to 9 grades In intercom or monitoring mode press and hold the 4 key to activate exposure adjustment and press 7
5. shield first put the top of the camera into the rain shield and then push in the bottom of the unit Make sure that it is solidly in and fix it with a screw at the bottom of the unit as shown below Monitor Setup Instructions Install the battery into the unit by sliding the battery cover off inserting the supplied rechargeable battery in the correct polarity and replacing the battery cover Battery cover Use Instructions Starting up and shutting down Press and hold the ON OFF key on the right side of the camera for 3 seconds to start up The logo will be displayed with a single beep sound On the display standby picture transmission signal battery icon time and date The screen will enter into standby mode after several seconds if no buttons are pressed In standby mode the red LED will flash every 4 seconds When the battery is low the red LED will flash every second Please recharge the unit battery when this occurs To lock and unlock the monitor press the ON OFF button once Press and hold the ON OFF key for 3 seconds to shut down Pairing the Monitor and Camera up to 3 monitors can be paired to 1 camera When the monitor is off press and hold the ON OFF button and when the logo is displayed on the screen immediately click the ON OFF button again 5 times the screen will show Pairing At the same time press the Reset button of
6. the outdoor camera twice The red LED will flash and then attempt to pair to the monitor If an image from the camera shows up on the screen of the monitor the pairing has been successful If no image shows up within 1 minute attempt to pair it again One pairing has been completed for multiple units test it by pressing the Call button on the outdoor camera if the monitors all display then they have all been paired correctly Menu When the screen is lit up if the unit is in standby mode press the ON OFF key to activate the screen again press and hold the FUNC key to enter into the menu Press the FUNC key in sequence to enter into Time Setting Ring Setting Lock Delay Setting and PIR Setting respectively Date amp Time Setting Press the T V key to adjust the date or time Press the OK key to confirm selection and move on to the next setting Press the key to adjust the digit size Press the OK key to confirm settings and return to standby mode Ring Setting Press the T V key to choose the ringtone that you like 12 ringtones in total Press the key on the left side of the unit to increase or decrease the volume 7 levels in total To mute press and hold the key and a mute symbol will appear Press the OK key to confirm your selection and return to standby mode Lock Delay Setting This
7. to adjust the grad of exposure with each press adjusting one grade Photo Preview amp Delete When the screen on the monitor is activated To preview press and hold the Jag key to display the pictures taken with the photos sorted by time with the most recent first Use the T V buttons to scroll To delete press the FUNC key and use to select yes one photo or no or all delete all Press the OK key to confirm To exit press the OK key to exit photo preview Battery and Charging Please fully charge the batteries before using them for the first time When the monitor is low on battery the red LED will flash every second please recharge the battery immediately The monitor can be charged using the charging dock when charging is completed a green LED will light up When the battery is fully charged it will automatically stop charging Note When the power is low display and photo taking functions won t work properly Night Vision The Infra Red PIR will work up to a distance of 1 5m best detection at 0 8m When it is pitch black it will display black and white NOTE Please keep the IR PIR sensor on the camera clean Wiring Diagram for Door Lock Controls available separately Unlocking power 12VDC ME ere Wire connector of outdoor unit Electrolock oO Electrolock maintain close if connect 5 Electrolock maintain open if connect 4

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents