GSM-3ECLK Comelit Powercom 1e1h05
Contents
1. up to a maximum of 3 numbers Each SMS must start with the pass code default 1234 in the following format 12 1234 followed immediately by a command E g to program the telephone number 0987654321 enter the following SMS Up to 3 numbers can be sent together in a single SMS as follows 12 1234 1 1tel number1 12tel number2 1 3tel number3 11 Telephone number 1 12 Telephone number 2 13 Telephone number 3 12 1234 1 10987654321 Pass code Function code Data 3 It is recommended to change the no answer time if there is more than 1 number stored This stops the unit ringing a number after a set time and can be used to prevent voicemail answering the call Send the following SMS 42 1234 52 Where can be 2 digits from 10 99 seconds default is 20 The unit can allow up to 100 telephone numbers to be stored for users to be able to ring the system for automatic entry This uses caller ID like a phone to determine the identity of the caller First the unit must know what country it is operating in 4 Program the country code as follows 4 ox Where can be 1 3 digits For uk insert 44 for Ireland 353 Do not 1201234871 22 use any leading zeros 5 Enter the telephone numbers required to have access control Do not enter country code just the complete number as you would dial it Up to 3 numbers can be sent together in the same SMS Just 12 1234 720987654321 add 72 then the number then each ti2. LED should not turn off Fault finding amp FAQs Q The unit will not power up No LEDs on A Check power supply voltage is within 11 5V 12 5V DC Q The unit powers up but there is a bleeping from the door station A This means the unit is not able to detect the network for some reason Check the SIM card is activated and has calling credit Power off the unit remove the SIM and check it in a mobile phone to verify it can make a call Check the SIM does not ask for a PIN code when put in a phone If it does then disable the PIN code request Check the SIM is a standard GSM SIM not 3G or 4G only SIM If you are unsure contact your SIM card provider to verify Frequency of operation should be any one of the international quad band standards 850 900 1800 1900 MHz Check the reception is good Poor reception is not sufficient Check the antenna has been mounted as high as possible not near large metal objects or wet green shrubs etc Check the antenna connection Visually inspect that the centre pin inside the antenna is intact and has not been pushed back inside the fitting Q The unit calls the first number but there is not enough time to answer before it diverts to the next number A Increase the no answer time as per programming instructions Q The unit calls the first number but voicemail comes on before it can ring the second number A Decrease the no answer time as per programming instructions Q
3. Dial in number 21 Remember to begin each new SMS with pass code 12 1234 Note DTMF Programming is done by calling the unit amp entering the pass code first then after a long single confirm tone commands can be entered A fault is indicated by 3 short bleeps Additional Wiring Information A C Strike Lock Wiring GSM module ACIO Strike From 12v d c power supply Exit Button Optional NO1 O emergency break glass Keypad module unit D C Magnetic Lock Wiring GSM module Magnetic Lock Recommend diode fitted From 12v d c power supply Exit Button C11O NC1 O Optional NOt emergency OO break glass unit Keypad module Keypad Programming Firstly you will be required to enter a new programmers code 1 Power up the unit 2 Insert a link between terminals PGM and or GND Check red LED is ON 4 Enter in a code of your choice from 1 to 8 digits long then press E 5 Wait for 10 seconds or for the confirm tone to sound 6 Remove the jumper NOTE If you make an error press the button with the KEY symbol several times to cancel and start again Entering a new user code 1 Press 0 then E Check that the red LED is lit 2 Enter in the programmers code then press E 3 Enter the relay ID number 1 or 2 then press E 4 Enter 0 for latching relay or 1 99 for pulse relay time then press E 5 Enter the new code followed by E 6 The
4. GSM 3E CLK V3 5 Installation 1 Before you install this equipment please read this full manual 2 Ensure that there is good network reception at the location where it will be installed 3 For medium or low reception areas to reduce audio interference on a call install an optional external antenna Ensure it is kept as high as possible and ABOVE all electronics 4 5 feet minimum Entrance Pillar Side View Wiring 4 Carefully follow the wiring instructions Additional wiring suggestions for electric strike lock and magnetic lock are shown overleaf Optional Antenna Speech panel Elevated position Intercom Transmitter GSM 3E 8 meters max Keep short as possible for best audio quality Jl Speech Panel Connections Power LED Modem LED CPU LED x oO 2 SPK nrn w O0OOdT 0M WOO OO OOVOUVVO o Relay 1 Relay 2 X l Optional 4 7 power Suppiy input limit WOOOOOOO OOOO OOO z tiona MnNe ItIY lt NK Serr NNN p pDtr lt lt GOOCO0O BT TESOCSOCSS Output exit button Keypad Connections Messer ceeescececceeseescceescecseesceeesceescesccoceog T Microphone R d strip indicates ve terminal Polarity is critical SIM card 5 Register your SIM card with the network and check it works in a mobile phone first If you are using a Pre pay or Pa
5. The caller ID part does not work A Be sure to program the caller ID part under 72 feature If your number is a private or number withheld then it will not work Even if you have already programmed a number to receive a call from the intercom if you also want that number to have caller ID access it must be programmed under the 72 feature also Ensure the number is entered as you would normally dial it from another phone Do not put the country code in front of the number Enter the country code in which the unit is operating in separate under the 71 feature International callers ringing the intercom may not work Q There is no audio from the gate but the person at the gate can hear ok A This can be due to low reception Check reception level by 20 Change SIM card if necessary to another network which may have better coverage Purchase a high gain antenna This may also be caused by either a defective microphone or incorrect microphone wiring or a short circuit by whiskers between the centre core and the shielding or excessive microphone cable length Q The audio quality that can be heard on the remote telephone is poor or humming buzzing A A small amount of GSM buzz can be considered normal on GSM intercoms but not so much that causes inability to hear the person speaking This can be caused by the GSM antenna being mounted too close to the speech panel or not mounted high enough Try earthling the speech p
6. anel chassis to OV of the power supply This is also a symptom of poor reception Try above steps on checking and improving reception Q The or key does not work when the intercom calls a phone A Check if you can hear the relay clicking at the gate when the or key is pressed during a call If it can be heard then the system is working check wiring between the relay and the lock or gate panel If the relays do not make a clicking sound then check this feature on a different mobile cell phone or landline If it works on a different phone check the settings on the phone in question under DTMF tones Failure of DTMF tones to operate correctly is also a symptom of low reception Check steps above on improving reception Try pressing the buttons longer when attempting to activate the gates or door User Manual For GSM 3E CLK Wireless Intercom This GSM intercom system will call up to 3 telephone numbers in sequence when the call button is pressed There are several modes of operation depending on how the unit has been programmed by your installer The following instructions will assume default programming Intercom calling your phone Call button pressed My Gate CALLING ANSWER DECLINE Answer call Sending SMS Commands Press to open OR Press to hold open and Press 1 to release again Only some gate systems allow hold open control depending on manufacturer De
7. fault pass code 5678 is shown in all examples This may have been changed by your installer Trigger Gate Door SEND SMS 33 56 8 i 25 es pt HOLD OPEN FEATURE OR PARTY MODE Latch or hold open gate door SEND SMS 34 56 8 Eii Unlatch gate door SEND SMS 35 56 8 E a 3 Some gate systems allow hold open control depending on manufacturer Send the following SMS commands to control the gates Calling the intercom options Dialling MY GATE END Option 1 If your number is saved inside the intercom memory just dial it and it will activate the door or gate without answering your call The intercom will end the call for you Check stored numbers If limit switch fitted check gate status SEND SMS SEND SMS x22 21 O dial out number Dial in number for caller ID access Reply will indicate opened or closed 33 5678 Option 2 If your number is not saved in the intercom memory it will answer the call Enter the code on your telephone keypad to activate the door or gate default code shown
8. me The pass code only needs to be put at the beginning of each new messge Additional Programming Parameters Description Change programming password Change access control password allows users not in caller ID list to call intercom and use pass code to activate relay Change monitoring mode password dial to listen in mode Delete a button calling number where n number 1 2 or 3 N A 3 3 122 2 03 4 Microphone volume Where level 0 4 Relay time Where 1 9999 seconds 1 sec Max call time Where 005 999 seconds 3 digit code 60 sec Max monitoring time for listen in mode when calling the intercom 00 60 mins 00 no limit Unit can call or SMS service number by set duration to prevent SIM card deactivation if seldom used 00 60 days 00 no inform Choose between scheduled call to service number or send SMS to 1 service number 1 for SMS 2 for call Store service number to receive scheduled SMS or call from N A intercom Delete service number N A Dial in mode for withheld numbers or non stored numbers 1 answer the call amp wait for pass code 2 answer the call amp automatically activate 2 way speech 51 1 53 22 005 i 55 57 58 77number 77 65 73 Delete phone number for caller ID access 73 999 Restore defaults Check stored numbers Note no pass code needed for this command O dial out number
9. y amp Go SIM it will need topped up first Your SIM should be GSM compatible 6 Ensure the power is OFF before inserting the SIM card 7 Carefully slide the SIM holder in the OPEN direction insert the SIM and slide in the CLOSED direction to lock it in place Do NOT Force or use a screwdriver 8 After a final check of wiring switch on the power 9 Allow 20 30 seconds for the unit to boot up and detect the network Once successful connection has been made the unit will sound a confirmation tone and the status LED will begin flashing If there is a fault or problem the unit will emit a series of bleeps or warning tones If this occurs check 1 That the SIM card has been activated and has credit 2 That the SIM card does not require a PIN code disable this in a phone 3 That the SIM card can make and received a call on a phone 4 Switch off power remove and reseat the SIM card and try again Installation Manual Programming Programming is best done by SMS text It can also be done by DTMF froma normal telephone 1 First check reception Send the following SMS to the unit 20 The unit should reply SIGNAL LEVEL PONTO TANT TTE Where will be between 1 and 31 7 7_ Below 14 can cause problems with relay operation or no voice from the gate to the 1 12 13 20 21 31 Poor Medium Good house Take action to improve reception 2 Program the numbers you wish the unit to dial when the call button is pressed
Download Pdf Manuals
Related Search