VIP - User Manual 27_06_2012
Contents
1. 8 3 8 4 Communication Address Each Power meter in a communication system must have its own unique address ElNet VIP works on MODBUS protocol so the available addresses are from I to 247 Baud Rate The Baud Rate is the communication speed in Bits per second BPS for communication between ElNet VIP with the PC or other device The better the communication line quality the faster the communications may be higher Baud Rate value If the communication line is routed through a noisy environment it may be necessary to decrease the Baud Rate Available Baud Rates for the ElNet VIP Are 300 600 1200 2400 9600 19200 bps Parity The parity can be defined as ODD NONE or EVEN CONTROL APPLICATIONS Ltd Supervision amp control system Tel 972 3 6474998 Fax 972 3 6474598 24a Habarzel St Tel Aviv 69710 Israel 8 5 Set up Communication 8 5 1 Press the Enter button for about 6 seconds until the insert password screen will appear 8 5 2 Use the 7 to change the password COD to 2 and press Enter 8 5 3 The message SET will blink on the screen On the second line you will find the functions that require setting Figure 6 1 Communications settings 8 5 4 Use the f buttons to chose the required communication feature and press Enter e Address Adr can be changed by using 7 buttons from 1 to 255 when finished press Enter e Baud bud use the2. buttons to choose 300 600 1200 2400 4800 9600 19200 e Parity PAr use the T buttons to choose from O81 ODD 8 data bit 1 Stop bit E81 EVEN 8 data bit 1 Stop bit n l NONE 8 data bit 1 Stop bit CONTROL APPLICATIONS Ltd Supervision amp control system Tel 972 3 6474998 Fax 972 3 6474598 24a Habarzel St Tel Aviv 69710 Israel 9 No volt relay 9 1 9 2 9 3 General When the voltage is proper above 50VAC adjustable and the phases order is proper the indication relay is closed as appears at the wiring diagram The maximum current that is possible to transfer through this relay is 150ma which is enough to operate a regular control relay No volt alarm setting 9 2 1 In order to set the minimum voltage value for the no volt relay press the Enter button for about 6 seconds 9 2 2 Use the T buttons to change the password to code 21 and press Enter 9 2 3 SET AL will appear and it would be possible to set the min voltage ratio by using the 7 After setting this value save it by pressing the Enter button Phase order alarm 9 3 1 In order to turn ON OFF the phase order relay press the Enter button for about 6 seconds 9 3 2 Use the T buttons to code 31 and press Enter 9 3 3 The phase order screen will appear and it would enable you to select YES NO equivalent to ON OFF After setting the desirable option save it by pressing the Enter butto
3. 72 3 6474998 Fax 972 3 6474598 24a Habarzel St Tel Aviv 69710 Israel j Dear customer thank you for selecting the VIP Multimeter for measurements of voltage current power and power factor 1 Mechanical Installation Comment Please do not install the VIP Multimeter close to electrical bars Please leave enough space for approaching the device from its back side for providing technical support 1 1 Please choose the proper place for installation in panel and prepare a square hole according to exhibit below Height 90 mm Space in the electrical panel 1 2 Please insert the VIP Multimeter into the suitable space which is to be prepared in advance Make sure that the device is inserted in the right direction The device has a plastic knob which adjusts itself for installation in electrical panels The thickness of the panel door should be less than 4 mm CONTROL APPLICATIONS Ltd Supervision amp control system Tel 972 3 6474998 Fax 972 3 6474598 24a Habarzel St Tel Aviv 69710 Israel 2 Wiring diagram VIP POWERMETER Control Applicatoin Ltd Measurements Power re v3 v2 V1 1 A o oJolo fsfs lolo 9x4x8 a a a aye L2 L1 Communication Optional Main Busbar CONTROL APPLICATIONS Ltd Supervision amp control system Tel 972 3 6474998 Fax 972 3 6474598 24a Habarzel St Tel Aviv 69710 Israel 3 Specifications 3 1 T
4. CONTROL APPLICATIONS Ltd Supervision amp control system Tel 972 3 6474998 Fax 972 3 6474598 24a Habarzel St Tel Aviv 69710 Israel 03 VIP Voltage Current 4 Power MultiMeter VIP Current x Power Multimeter Rev 1 6 Nee CONTROL APPLICATIONS Ltd Supervision amp control system Tel 972 3 6474998 Fax 972 3 6474598 24a Habarzel St Tel Aviv 69710 Israel Table of Contents Mechanical Installation acer een 3 II AAA E E E 4 Si PiE waka 5 3 1 Technical Specifications ooocconoccocnocccnonocconnocccnonocccnnocccninacoss 5 3 2 Measuring Specifications ooocconoccccnncccnonocconnocccconocccnnoccocinecoss 5 Current transformer ratio settings cccsccccsssccssscccsscccsssccessces 6 Measured values display assess Edd OZ en 6 Peaks CISDIAY ccccevenesecesesnercousanocessyvessyesceussecscvexosessuwscesersecseescvesseonsee 7 EIVGQICATION ICO AP OE erahnen 7 Communication SCN OS sss ss sss sss sss ssssssssssss sassa aas OGG 0 sassa 8 8 1 Communication Address ssccccccsssssccsssssccccssssccsssssscosees 8 8 2 AA 8 8 3 Available Baud Rates for the ElNet VIP 00 20002 8 SA DACIY mosz scscscesspccsesisnccesucursceccessncnuvssscesssesssusesesrsaseessssearerees 8 8 5 Set up Communication ernennen 9 ENO YONG OIA AA A EEEE E RERE 10 A 10 9 2 No volt alarm setting sasiada cca 10 9 3 NK L alarm na 10 CONTROL APPLICATIONS Ltd Supervision amp control system Tel 9
5. echnical Specifications Item Description 3 2 Measuring Specifications Measurement Parameter Display Range Measuring in Display Range in direct direct connection connection scaling factor 1 scaling factor 1 0 01 6A 0 01 6A 0 01 999KA Neutral Current 0 01 6A 0 01 6A 0 01 999KA calculated Voltage L N 0 00 650 V 0 00 650 V 0 01 999KV Voltage L L 0 00 650 V 0 00 650 V 0 01 999KV Frequency Hz 45 1 65 1 Hz 45 1 65 1 Hz 45 1 65 1 Hz Active power total phase Reactive power 0 00VAR total phase 999KVAR 0 00W 999KW Apparent power 0 00VA total phase 999KVA Power Factor cap ind 1 00 1 00 1 00 1 00 1 00 1 00 CONTROL APPLICATIONS Ltd Supervision amp control system Tel 972 3 6474998 Fax 972 3 6474598 24a Habarzel St Tel Aviv 69710 Israel 4 Current transformer ratio settings 4 1 Press the Enter button for about 6 seconds 4 2 The enter password screen will appear COD 4 3 Use 7 button to change the code to 1 and press Enter 4 4 The current transformer set screen will appear 4 5 The headline SET will be displayed on the screen on the second line the secondary value of current transformer 5A the third line allows to define the value of the primary current transformers with the 7 buttons At the end press Enter 5 Measured values display 5 1 Use the 7 buttons to browse among all the display screens including th
6. n
7. ree phase display of voltage current power frequency power factor and integrated screens of voltage current and power factor for each phase CONTROL APPLICATIONS Ltd Supervision amp control system Tel 972 3 6474998 Fax 972 3 6474598 24a Habarzel St Tel Aviv 69710 Israel 6 Peaks display 6 1 Pressing the Hi Lo button each press replaces screens circularly enables you to browse among the screens specifying the peak of voltage and current that were ever measured for each phase The first screens display the highest values measured of voltage and current Hi the next screens display the lowest values measured of voltage and current Lo and then respectively high and low frequency and power factor for each phase 7 Indication led 7 1 The indication led easily enables to identify whether there is voltage in phases LI L2 L3 In case there is voltage in phases connections the led will be turned on 00 VAC at least p VIP Yoltage Current amp Pewar MultiMeter CONTROL APPLICATIONS Ltd Supervision amp control system Tel 972 3 6474998 Fax 972 3 6474598 24a Habarzel St Tel Aviv 69710 Israel 8 Communication Settings In order to connect the ElNet VIP Power Multimeter to a PC or other device for successful communications both Communication Setup parameters must match i e the PC port and the configuration settings of the Power meter Address Baud Rate Parity must match 8 1 8 2
Download Pdf Manuals
Related Search