2 - EM Nordic
Contents
1. Turn the power on it is in manual running mode Digital tube display 101 this time not in the programming state To control the lamp shall press Program button 2 seconds after the flashing light blink can be programmed At this point adjust each channel potentiometer lamp will be run accordingly e If in the programming state press the Program button 2 seconds programming lights off Blackout indicator light this time enter into the Blackout state Press the Blackout button to exit Blackout state and then press the Auto Del button again the console automatically run the program If a BANK where without any programming SCENES then SCENES will not run the console only run the programmed SCENES of a BANK If a channel controlled by the adjustable potentiometer SCENES channel run will not be programmed value if adjustable potentiometer control is prohibited ie the potentiometer putter is in the most bottom then SCENE run the channel programmed value 1 MANUAL RUNNING 1 AUTO TRIGGER LED and MUISC TRIGGER LED lights are all off 2 select a BANK use Tor button or through the Midi interface use the Midi signal to select 3 press SCENE button to run A SCENE 4 use Midi signal to run SCENE 2 AUTO RUNNING 1 Press the Auto Del button automatically trigger indicator light bright 2 Press Auto Del button again exit automatic running mode 3 SOUND RUNNING 1 Press the Music Bank copy button the sound triggers2. in Microphone 4 AUTO mode is controlled by TAP SYNC and SPEED controlled 5 MIDI control through MIDI interface 6 Blackout master controlled by M annual or R emote 7 CHASE programming and CHASE runnyng manual control and renote control 8 Fade Time control 9 DMX polarity selects 4 Appearance use the streamline design HI Technology Parameter 1 AC adapter Input Voltage AC 100 240V 60Hz 50Hz Output Voltage and current 9V 1 0A 2 Outline Size 482X132 X70mm Packing Size 570X 175X90mm 3 N W 2 4Kg G W 3Kg IV Installation 1 Installation First put the controller on the special desk and then connect the controller and the light through the signal line 2 Connection of AC adapter The exclusive AC adapter should be used between the connection of controller and power and please confirm if the rated voltage and frequency is accordance with the power supply Parameter of Input Voltage and Frequency Voltage AC100 240V Frequency 60Hz 50Hz V Operation Production Introduction 1 There is 192 DMX channel adjusting output level in every SCENE 2 8 SCENES are available to be programmed for each BANK When SCENE running all programmed SCENE of one BANK will be executed continuously in a cycle 3 Select bank using t and button Also you can select desired bank using MIDI signals through MIDI interface there are totally 30 banks once only one can be ch
3. Bank copy button then click the MIDI ADD this time all three said that it had flashing lights BANK 2 stored in Chase1 d Through the 1 key to select BANK 3 click the Music Bank copy button then click the MIDI ADD this time all three said that it had flashing lights BANK 3 stored in Chase1 e Through the T key to select BANK 4 click the Music Bank copy button then click the MIDI ADD this time all three said that it had flashing lights BANK 4 stored in Chase1 f Through the 1 key to select BANK S click the Music Bank copy button then click the MIDI ADD this time all three said that it had flashing lights BANK 5 stored in Chase1 g Through the f key to select BANK 6 click the Music Bank copy button then click the MIDI ADD this time all three said that it had flashing lights BANK 6 stored in Chase1 h At this point press the Program button and then press and hold 2 seconds the console from the Program state to Blackout state while the first one shows a digital control will disappear according to Blackout key to exit Blackout status I And press the Chase1 press Auto Del button the console will run is stored in the Chasel in 48 SCENES MIDI channel set up and operation 1 MIDI channel settings 1 Hold down the MIDI button 2 seconds the third and fourth digital pipe flashing press t key and keys to select a MIDI channel 01 16 2 and then hold down the MIDI button 2 seconds to end the MIDI channel set
4. adds the programmed SCENES of the BANK 3 Program a Chase A Addastep in Chase 1 convert the STEP display of the chase and BANK and SCENE display press Tapsync Display button show Chase and the programmed steps of the Chase press Tapsync Display button again show SCENE and BANK of Chase 2 Add a step in Chase press Tapsync Display show the programmed steps of the Chas if you have programmed 15 steps add a step between step 9 and step 10 use or to select step 9 press Midi add button the second digital tube display SCENE the third the fourth digital tube display BANK select the desired SCENE press Midi add button the selected SCENE has been added to step10 while the original step10 change tostepll step 12 change to step 1 Z analogy B Delete a step in Chase Delete a step in Chase select the delete step if we delete the first step 10 use f or key to select to the step 10 press Auto Del button the first step 10 has been deleted the f step 11 change into step 10 step 12 become to 11 analogy 4 Delete a Chase 1 select the Chase need to delete 2 hold down Auto Del button press the Chase which has been deleted again SCENES itself in the chase still exists 5 Delete all Chase all the SCENE itself still exists 1 Turn off the power press Auto Del button and button at the same time 2 Close power all the lights flashing three times indicated they had been deleted at this time SCENES Running
5. ON 8 113 128 ON ON 9 129 144 ON ON 10 145 160 ON ON 11 161 176 ON ON 12 177 192 ON ON Press SCANNER button corresponding LED is lit and the output of continuous 8 channels is enabled to be adjusted when SCENES are running if adjustable potentiometer control is OFF channel output level is not affected by the potentiometer if adjustable potentiometer control is ON channel output is changed correspondingly with the adjustable potentiometer 2 SCENES button Press one SCENE button to run scene or to store and the second digital tube head display SCENES 1 8 3 Adjustable potentiometer Regulator adjustable potentiometer to change the output range of the DMX channel the minimum is 0 the maximum is 255 or from 0 to 100 adjustable potentiometer 1 8 control continuous 8 channels 4 Page Selector button Select Page A or Page B Page A is the former 8 channel of each SCANNER Page B is afterwards 8 channel of each SCANNER 5 SPEED SLIDER Move the slider to adjust light speed 6 FADE TIME SIDER Move the slider to adjust FADE TIME 7 LED DISPLAY 8 BANK batton t The third and fourth digital tube display BANKS 01 30 press the f keys BANK increase or decrease the display SCENE is the SCENE of BANK 9 Chasel Chase6 button Used to Chases program or the choice of Chases operation 10 Program button Turn the power on it is in manual mode press PROGRAM for 2 seconds corresponding prog
6. Scandlight 192 DMX Controller User s Manual Item no 935799 scond LIOHT I Preface Thank you for using our controller For your safety please read the User s Manual carefully before your operation Note This Manual includes the important information of installation operation safety instruction Please install and operate as requested in the Manual meanwhile please keep the manual for any unexpected requirement This Manual includes the important information of installation and operation Please install and operate the controller according to the instructions strictly And it must be power off when open the controller or before repair A Please read the complete contents of this manual please keep this manual attach with the controller for any preview B In order to make sure the correct and safety installation operation and maintenance well know and follow to the instructions of Manual is necessary C We will not take any responsibility to the controller damage property loss or body injure which caused by the incorrect installation operation and maintenance NOTICE The data which inside the Manual maybe changed due to the continuous improvement and we ll not make another notice We will keep the right to any specification update during improvement 1 Packing Content Caccessories 1 AC adapter 1PCS 2 Signal Cable 1PCS 3 User s manual 1PCS 4 Maintenance Card 1PCS 2 Unpacking Instru
7. and then hold down the SCANNER which need to copy and press another SCANNER Copy a SCENE 1 select the SCENE which need to copy 2 press Midi add button 3 select a BANK and then press the one need to copy to SCENE button Delete a SCENE set the value of the ALL DMX CHANNEL of the SCENE to 0 1 select the SCENE which need to delete 2 Hold down Auto Del button and then press the SCENE which need to delete Delete all of SCENE ALL DMX CHANNEL value is set to 0 1 turn off the power press Program button and 1 button at the same time 2 closed the power Copy a BANK 1 select the BANK which need to copy 2 Press Music Bank copy button Delete a BANK select the BANK which need to delete press Auto Del button and Music Bank copy button at the same time CHASES PROGRAMM f the programming state can be directly CHASE programming if not programmed state hold down the Program button 2 seconds to enter programming state programmed indicator light flashs 1 Program a SCENE to CHASE 1 the maximum of a Chase is 240 SCENES that is 240STEPS 2 during running first programmed SCENES run first 3 select a Chase 4 select the SCENES of a BANK must have been programmed SCENE 5 press Midi add button 2 Copy a BANK to Chase the maximum of a Chase is 30 BANK 1 select a Chase to store BANK 2 selecta BANK press Music Bank copy button 3 press Midi add button again Chase
8. ction Please check if all the contents are completed after unpacking then check if the controller is undamaged Please you can keep the original package and return to the factory if it s damaged 3 AC Power Check whether the voltage is accordance with the rated power 4 Safety Specifications all the safety items of operation includes installation and before operating 1 Unpacking the carton and take out all the accessories and open the poly package take out the light from the carton and put it in a certain platform for operation 2 The controller must keep dry and avoid to use under the Moist Overheat or Dusty surroundings And keep it far away from the water or other liquid 3 The installation operation and maintenance must be managed by the qualified professional and make sure to operate it under the instruction of the Manual 5 Please check if the voltage is accordance with the rated power before installing Notice Please make sure it s power off before any installation repair and clean IL Introduction 1 Controller Channels 192 channels 2 Display 1 4 digits LED display 2 Fird digit of LED shows CHASES the second digit of LED shows scenes 3 Third and fourth digit of LED shows BANKS 4 The second third fourth digit of LED show steps or 0 255 or TIME 3 Additional Function 1 30 Banks each composed of 8 programmable scencs 2 8 fades adjusting output level 3 Built
9. hen click the Blackout key to exit the Blackout mode 16 MIDI input Midi signal input 17 DMX polarity select Select DMX polarity of the output 18 DMX output DMX 512 signal output 19 DC Power input DC9 12V 300mA min 20 Flash control output interface Hole down the flash control button next to the red LED will blink 2 second 21 Flash signal button Through the audio signal lines and the audio jack of the flash connection VI Appendix SCENES Program Press PROGRAM for 2 seconds entre programming state programming light flashes SECNE PTOGRAMMING the maximum is 8 SCENES of a BANK 1 Press SCANNER key to select DMX channel Choose 8 or more channels every time 2 Select different channel to control several devices at the same time 3 Regulator adjustable potentiometer to set the output state when the output is set to a satisfactory state turn off the adjustable potentiometer 4 Select and adjust output level continuously until all devices are set 5 Press MIDI ADD button 6 Through 1 button to select the BANK you need 7 Press SCENE button to strobe the SCENE 2 SCENES Edit 1 Select need to edit the scene of a BANK 2 Use SCENE programming method to adjust to the requirement of device 3 Press MIDI ADD button 4 Press SCENE button to strobe the SCENE all indicated lights flash three time show that it had programmed the same below SCANNER COPY Supposed a SCANNER had set copy it to another SCANNER
10. iding potentiometer different channel output state When set to a satisfactory output state click the MIDI ADD button and then click SCENE 1 button this time all the lights flashing three indicated that they had programmed the first SCENE Edit the same way as the other seven SCENES c Select store where one of the CHASE for example stored in CHASE press CHASE key the first digital tube will display one d Through the key to select BANK 1 click the Music Bank copy button then click the MIDI ADD this time all three said that it had flashing lights BANK 1 stored in Chasel e Through the f key to select BANK 2 click the Music Bank copy button then click the MIDI ADD this time all three said that it had flashing lights BANK 2 stored in Chasel f Hold down the keyboard and then press the Program at this time 2 seconds the console from the Program state to Blackout state while the first one shows a digital control will disappear according to Blackout key to exit Blackout status g And press the Chase1 press Auto Del button the console will run is stored in the Chasel in 16 SCENES 2 edit the address code of the lamp is running a different or the same scene in different procedures 1 set up two different address code of lamps such as the address code is set to 001 and 017 respectively 2 First edit the address code to run the lamp for the 001 scenario a Click SCANNERS 1 key making next to the green LED light Then ed
11. it BANK 1 of 8 SCENES adjust the sliding potentiometer different channel output state When set to a satisfactory output state click the MIDI ADD button and then click SCENE 1 button this time all the lights flashing three indicated that they had programmed the first SCENE Edit the same way as the other seven SCENES b Through the t key to select BANK 2 and then edit the BANK 2 of 8 SCENES adjust the sliding potentiometer different channel output state When set to a satisfactory output state click the MIDI ADD button and then click SCENE 1 button this time all the lights flashing three indicated that they had programmed the first SCENE Edit the same way as the other seven SCENES 3 And then edit the address code to run the lamp for the 017 scenario a Click SCANNERS 2 buttons making next to the green LED light Through the 1 key to select BANK 3 and then edit the BANK 3 of 8 SCENES adjust the sliding potentiometer different channel output state When set to a satisfactory output state click the MIDI ADD button and then click SCENE 1 button this time all the lights flashing three indicated that they had programmed the first SCENE Edit the same way as the other seven SCENES b Through the T key to select BANK 4 and then edit the BANK 4 of 8 SCENES adjust the sliding potentiometer different channel output state When set to a satisfactory output state click the MIDI ADD button and then click SCENE 1 button this time all the
12. light bright SCENES run by Sound Control 2 choose the BANK to run can be controlled by manually or the Midi signal 3 click the Music Bank copy button again exit the sound running mode 4 MIDI RUNNING Select BANK and SCENES to run by MIDI signal whenever it is in manual running auto running or sound running 5 CHASE RUNNING 1 it has been programmed Chase when the Chase running SCENE automatically stop running 2 Chase running also has auto running or sound running and Midi running 3 you can also a Chase or multiple Chase to run first selected the first run 4 Press the Chase button Chase is running the first LED display the running Chase 6 OUTPUT DELAY ADJUST Adjust FADE TIME potentiometer the output follows changes Programming example 1 edit the lamp to run the program more than 8 SCENES First the address of the specified lamp code such as the address code is 001 The console is programmed state which is programmed in the flickering light a Click SCANNERS 1 key making next to the green LED light Then edit BANK 1 of 8 SCENES adjust the sliding potentiometer different channel output state When set to a satisfactory output state click the MIDI ADD button and then click SCENE 1 button this time all the lights flashing three indicated that they had programmed the first SCENE Edit the same way as the other seven SCENES b Through the key to select BANK 2 and then edit the BANK 2 of 8 SCENES adjust the sl
13. lights flashing three indicated that they had programmed the first SCENE Edit the same way as the other seven SCENES 4 Edit Address Code for the 001 and 017 of the lamp to run the same scenario a Respectively Click SCANNERS 1 SCANNERS 2 button making the green LED light next to the corresponding Through the T key to select BANK 5 and then edit the BANK 5 of the 8 SCENES adjust the sliding potentiometer different channel output state When set to a satisfactory output state click the MIDI ADD button and then click SCENE 1 button this time all the lights flashing three indicated that they had programmed the first SCENE Edit the same way as the other seven SCENES b Through the key to select BANK 6 and then edit the BANK 6 of the 8 SCENES adjust the sliding potentiometer different channel output state When set to a satisfactory output state click the MIDI ADD button and then click SCENE 1 button this time all the lights flashing three indicated that they had programmed the first SCENE Edit the same way as the other seven SCENES 5 All edited BANK stored in the Chase a Select store where one of the CHASE for example stored in CHASE1 press CHASE key the first digital tube will display a b Through the key to select BANK 1 click the Music Bank copy button then click the MIDI ADD this time all three said that it had flashing lights BANK 1 stored in Chase1 c Through the T key to select BANK 2 click the Music
14. nalysis the complained problem and give a final solution to customer Vil Faulty Disposal Faulty Description Solution Light doesn t work 3 Check if the fuse is burnt out 4 Check if the power is correctly connected 5 Check if the circuitt 12V or 5V is short circuited Light is working but not controllable 1 Check if the DMX address code is correctly set by controller 2 Check the signal communication of the wires Lamp doesn t work 1 Check if the lamp is broken
15. ose 4 SCENES can be executed automatically and the duration is dependent on TAP SYNC DISPLAY scenes are executed under music or NOTE triggering also press a scene buttons by hand to run scenes 5 There are total 6 chases each contains240 scenes You can choose CHASES Running one or more and MIDI signal remote controlling Pane button function introduction 20 2 7 8 9 7 SCANNERS scenes L I en O S A STROBE I CF H O E a ss Q Oi 10 I i i I I El A O Q 11 Or O i Zl Zl O oO 12 O Or O z FH ij Fj CH 3 i aa amp A a a E x Or O z se FF s 8 O O I DMX OPENATOR 3 4 5 6 14 15 MIDI IN DMX POLARITY DMX OUT DCINUT SELECT 2 I 17 18 19 21 1 SCANNERS DMX channel buttons as the following list Computer light channel Adjustable LED potentiometer control 1 1 16 OFF OFF 2 17 32 OFF OFF 3 33 48 OFF OFF 4 49 64 OFF OFF 5 65 80 OFF OFF 6 81 96 OFF OFF 7 97 112 OFF OFF 8 113 128 OFF OFF 9 129 144 OFF OFF 10 145 160 OFF OFF 11 161 176 OFF OFF 12 177 192 OFF OFF Computer light channel Adjustable LED potentiometer control 1 1 16 ON ON 2 17 32 ON ON 3 33 48 ON ON 4 49 64 ON ON 5 65 80 ON ON 6 81 96 ON ON 7 97 112 ON
16. ramming light flashes SCENE and CHASE are ready to be programmed press PROGRAM for 2 seconds once more programming light goes out return to run mode 11 Midi add button A Press Midi button for 2s when running the third and fourth digital tube flash select channel by for press Midi button for 2s again end the settings options of the Midi channel the Midi channel is stored or any button can end the setting of Midi channel except for f and do not store the selected Midi channel B Used to program when under programming mode 12 Auto Del button A Inrunning mode press Auto Del button automatically trigger indicator light which indicates under automatic trigger mode press Auto Del button again to withdraw automatic trigger mode automatically trigger indicator light goes out B Used to SCENE and Chase program when in programming mode 13 Music Bank copy button A In running mode press Music button the sound triggers indicator light the SCENES can be triggered by sound press Music button again the sound triggers the indicator light off exit the sound trigger state B Used to SCENE and Chase program under programming mode 14 Tapsync Display button A In AUTO running mode the running speed of scene is decided by the last pressing of Tapsync Display button Max 10 minutes B Not in AUTO mode conversion 0 255 or 0 100 15 Blackout button Ban on all of the channel output But does not affect a variety of operations and t
17. s of complained problem included the item no delivered quantity delivery time faulty and pictures and the requirement of customer 2 QC and Technology department will analysis the complained problem and give a final solution to customer VII Faulty Disposal Faulty Description Solution control doesn t work 1 Check if the power is correctly connected 2 Check if the 12V or 5V is short circuited Single or multiple channel failure 1 check if the sliding potentiometer aging or damaged Single or multiple keys failure 1 Check if the aging or keys damaged VI Maintenance 1 Cleaning and Using Frequency of Product The light should keep clear in order to make sure it s available to work stably It s recommended to clean the light body and fan by each l5days The lens and filter should be cleaned periodically as well in order to keep the best effect Please never use the resolvable detergent to clean the filter in order to avoid the damage to the light When the light doesn t work please check if the fuse is burnt out or not If it is the same fuse should be replaced find out the faulty and restart the light But please note the repair must be handled by professional 2 Complain 1 The salesman will check the details of complained problem included the item no delivered quantity delivery time faulty and pictures and the requirement of customer 2 QC and Technology department will a
18. tings the new MIDI channel is stored you can also press the f key addition keys away from any one of keys to come the new MIDI channel will not be stored 2 MIDI operation NOTE ON Receive NOTE ON signals implement the corresponding functions B NOTE NUMBER FUNCTION ANK 00 TURN ON TURN OFF CENE1 01 TURN ON TURN OFF CENE2 02 TURN ON TURN OFF SCENE3 BANKI 03 TURN ON TURN OFF SCENE4 04 TURN ON TURN OFF SCENE5 05 TURN ON TURN OFF SCENE6 06 TURN ON TURN OFF SCENE7 07 TURN ON TURN OFF SCENE8 08 TURN ON TURN OFF SCENE1 BANK2 09 TURN ON TURN OFF SCENE2 10 TURN ON TURN OFF SCENE3 n 112 TURN ON TURN OFF SCENE1 113 TURN ON TURN OFF SCENE2 114 TURN ON TURN OFF SCENE3 115 TURN ON TURN OFF SCENE4 BANKIS 116 TURN ON TURN OFF SCENE5 117 TURN ON TURN OFF SCENE6 118 TURN ON TURN OFF SCENE7 119 TURN ON TURN OFF SCENE8 120 TURN ON TURN OFF SCENE1 121 TURN ON TURN OFF SCENE1 122 TURN ON TURN OFF SCENE2 CHASE 123 TURN ON TURN OFF SCENE3 124 TURN ON TURN OFF SCENE5 125 TURN ON TURN OFF SCENE6 126 BACKOUT VIL Maintenance 1 Cleaning and Using Frequency of Product In the open the control stations or maintenance work before they begin to make sure the console power supply disconnected the console s internal use vacuum cleaner at least once a year 2 Complain 1 The salesman will check the detail
Download Pdf Manuals
Related Search