AB-134 - SmartHomeUSA.com
Contents
1. n VOL Controls volume for the keypad Downloading IR commands If you don t have access to the A0505 remote and you need to program a learning remote you can download the IR codes from the internet IR codes compatible with the Philips Pronto remote controls can be downloaded from the following websites www channelvision com codes in Hex format www remotecentral com codes in Pronto format AB 134 Rear View AB 134 Side View Installation Gasket The AB 134 is shipped with a gasket This allows you to adjust the height and fit of a decorator trim plate Leave the gasket as is for a flush fit Remove the gasket to have the AB 124 stand above the plate Connectors To simplify installation the AB 134 has both 110 and RJ 45 inputs Only one of the inputs should be used at a time Connect the AB 134 as shown Balance The two potentiometers on the AB 134 adjust the volume levels of each speaker channel Use these to adjust the speaker balance in this zone fer 24VDC P 1044 CAT5 Audio Matrix Single Source System When using the AB 134 with single source CAT5 audio hubs the source mode jumper should be set for single source In this mode the source selectio2. through the Amp Link cable B Speakers powered by A0240 40Watt Amplifier 2 gt Ne Jumper Function Jumper on Pins 1 amp 2 Jumper on Pins 2 amp 3 Volume Level Default volume level Previous volume level Status Active Source Mode Off until Pwr is pressed Single Source Previous state Multi Source AB 134 Bottom View l _ al Pin 1 is to the right arrow is pointing at pin 1 Pin 3 is to the left Jumper is covering Pins 2 amp 3 Volume Level Status Active Source Mode uy ea a a ATA 68 TY Set switch to Using The A0505 remote control The A0505 is designed to allow you to control your P 1044 without having to touch the buttons on the AB 134 Simply point the A0505 remote control at the IR sensor located at the bottom of the AB 134 and press the desired button Zone Power Turns on off the zone output of the P 1044 Power Turns on off the AB 134 e CO CHANNEL VISION LED indicators lt on the AB 134 7 will light when ye se source buttons z are pressed on lt A the A0505 CHANNEL VISION POWER MODEL A0505 alh Source C Soe A BUS uN N L MUTE This will E mute the zone a
3. 2 CHANNEL VISION 1 Year Limited Warranty Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts free of charge in the USA for one year from the date of original purchase This is ano hassle warranty with no mail in warranty card needed This warranty does not cover damages in shipment failures caused by other products not supplied by Channel Vision Technology or failures due to accident misuse abuse acts of God or alteration of the equipment This warranty is extended only to the original purchaser when purchased through an authorized reseller A purchase receipt invoice or other proof of original purchase date will be required before warranty repairs are provided Mail in service can be obtained during the warranty period by calling 800 840 0288 toll free A Return Authorization number must be obtained in advance and can be marked on the outside of the shipping carton This warranty gives you specific legal rights and you may have other rights which vary from state to state If a problem with this product develops during or after the warranty period please contact Channel Vision Technology your dealer or any factory authorized service center Channel Vision products are not intended for use in medical lifesaving life sustaining or critical environment applications Channel Vision customers using or selling Channel Vision pr
4. Hz Operating Temperature 10 C to 50 C Specifications subject to change without notice 11 Connection Tips and Troubleshooting 1 Verify you have connected the CAT5 cable correctly Follow the TIA 568A standard at both ends Mis wiring can cause distorted sound prevent the system from functioning or possibly cause damage to the components in the system 2 Verify you have connected the speakers in phase Follow the label on the product Out of phase speakers can rob the system of its bass especially when driving dual voice coil speakers 3 Trouble with IR control a Verify you are using the correct remote control The AB 134 will respond to IR signals from the A0505 The A0505 can provide both volume control and source selection commands Other 3rd party remote controls that are capable of learning the IR codes from the A0505 can also be used b The top LED on the AB 134 acts as an IR receiver feedback LED that flashes whenever IR signals are received Check to make sure the LED flashes whenever you press buttons on your remote control If you don t see the feedback LED try replacing the batteries in your remote control c Make sure your IR emitters are placed directly over the sensor on the device you are trying to control 4 If no audio is heard check to make sure that the audio source is playing then press the power button on the AB 134 to make sure it is turned on a Note if the status jumper is on pins 1
5. amp 2 the AB 134 will turn off if there is no audio present for more than 2 minutes For most applications it will be desirable to place the status jumper on pins 2 amp 3 so that the AB 134 will revert back to its previous condition either on or off when music is played after a long pause b Check power supply and voltage Each Abus hub is powered by 24vDC The solid brown wire is and the striped brown wire is If proper voltage is not fed to each amplified keypad the system will not function normally 5 Observe wiring distance specifications The maximum recommended wire length between the audio hub output and AB 134 is 150 feet Although the AB 134 can work at greater distances such extreme distances are not recommended because erratic performance may result due to the power loss caused by the CAT5 wire Locally powering the keypad may be an option 6 If you need additional help troubleshooting the AB 134 please contact Channel Vision technical support 1 714 424 6500 or check our website for more details www channelvision com Compatibility The AB 134 adheres to the same protocols as Channel Vision s other CAT5 audio hubs to ensure maximum compatibility However when using the AB 134 in a multi source system we recommend using Channel Vision s multi source CATS audio matrix model P 1044 Multi source CAT5 audio products from other manufacturers may not and typically will not use the same control codes for adv
6. anced features such as source selection from the keypad How it Works The AB 134 can be used in two different modes 1 single source mode 2 multi source mode Mode selection is controlled by a jumper setting prior to installation When using the AB 134 with a single source CAT5 audio hub it should be set for the single source mode In this mode the unit provides basic controls volume up volume down and power on off When using it with a multi source CAT5 audio matrix it should be set for multi source mode In this mode any zone can independently select and listen to any source at any time Source selection can be done either from the AB 134 amplified keypad or by using the A0505 remote control Basic Operation Using the AB 134 Amplified keypad The Pwr power button located at the lower left of the keypad is used for source selection and to turn the unit on or off When in single source mode press and release the Pwr button to toggle the keypad on or off When in multi source mode if the keypad is off press and release Pwr to turn it on Press Pwr again to see the current source selection and press repeatedly to scroll through the 4 sources Press and hold the power button to turn the keypad off While the keypad is off press and hold the power button again to turn off the zone output of the P 1044 As you change sources when in multi mode you ll notice that the top 4 LEDs illuminate corresponding to the source you have selec
7. mpatible with the A0505 remote control e LEDs show volume level or source selection LED Indicators Can show volume level or source selection Top LED Indicator Flashes when IR signals are received 6 Volume Controls CHANNELVISION Increase or decrease volume level IR Window Receives signals from IR remote controls CPwr Pwr Source Button Keypad On Off control and source selection control when in multi mode Stripping and Connecting CAT5 Wire CAT5 cable should be stripped with a proper stripping tool such as Channel Vision s J 110 tool 1 Place the CAT5 between the blade and the first notch of the J 110 tool 2 Rotate the tool only once Multiple turns will cause you to cut into the inner wires Rotate 1 turn only 3 Inspect the inner wires for damage If any wires are cut start over at step 1 Slight pressure Check for damage Side view TIA 568A RJ 45 Modular Plug Top view Green White Left Channel Audio Ground Green Left Channel Audio Orange White Right Channel Audio Ground Blue IR Signal Voltage Blue White IR Status Voltage Orange Right Channel Audio Brown White Ground 24vDC Ground Brown 24vDC Specifications typical 25 C Operating Voltage 24VDC 2 3 Amps Cable requirements CAT5 or better Speaker impedance 6 8 ohm IR repeating 30 60kHz IR sensor range 40 40kHz 25 56k
8. n features are not available Pressing the PWR button will turn off the keypad but other keypads will continue to play Integrated IR repeating allows source to be controlled from any room S OUUUUUUUUUUUUUU0U U0UN S i j AB T2454 power supply CD player ESL included ee Optional IR emitters Multi Source Application When using the AB 134 in a multi source system with the P 1044 the source mode jumper should be set for multi source In this mode the source selection features are enabled allowing any zone to independently select and listen to any source at any time Integrated IR repeating allows sources to be controlled from any room Sa ooo Sat radio ccococo CD player SSS AB T2454 power supply included Optional IR emitters
9. oducts for use in such applications do so at their own risk and agree to fully indemnify Channel Vision for any damages resulting from such improper use or sale Tested To Comply With FCC Standards This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation A BUS is a registered trademark of LeisureTech Electronics Pty Ltd This product may be covered by one of the following patents US patent no 7 181 023 6 389 139 EP 1004222 AU 739808 NZ 502982 Mexico Z41196 Canada CA2301062 iBus is a registered trademark of Channel Vision Technology CHANNEL VISION 234 Fischer Avenue Costa Mesa California 92626 USA 714 424 6500 800 840 0288 714 424 6510 fax 500 326 rev B QO oo O C CHANNELVISION Cuo C Source ABUS C E E AB 134 A BUS CHANNEL VISION 2013 CHANNEL VISION TECHNOLOGY The AB 134 is an amplified keypad for Channel Vision s single source and multi source CAT5 audio systems It provides convenient volume control and source selection capabilities while its elegant decorator styling blends seamlessly with other wall switch devices Features e Compatible with all Channel Vision CAT5 audio systems e Supports IR control co
10. present at the source Status Active This jumper determines what happens when the status becomes active Typically when status becomes dormant Channel Vision amplified keypads go into a sleep mode which mutes the amplified keypad If the jumper is on pins 1 amp 2 when status becomes active the AB 134 will remain off until the power button is pressed If the jumper is on pins 2 amp 3 when the status becomes active the AB 134 will return to its previous state either on or off Source Mode This jumper determines if the AB 134 will be used as a multi source keypad or a single source keypad If you are using the keypad in a single source system set the jumper on pins 1 amp 2 If you are using the keypad in a multi source system set the jumper on pins 2 amp 3 Adding more power Using the A0240 with the A0302 The A0302 is the perfect complement to Channel Vision s A0240 amplifier It can utilize the Amp Link connection which provides a clean way to interrupt the speaker level audio from a low power system and output 40 Watts per channel to the speakers This is the perfect way to add power to low power distributed audio systems A Speakers powered by AB 134 keypad DE AE HE HE AB 134 keypad rear view Place switch in L R mode Speaker level audio is converted to line level to drive the amp Amplified audio is returned to the A0302
11. ted When source one is selected the first LED is illuminated when source two is selected the second LED is illuminated and so on After a source is selected the LED will stay lit for 5 seconds then it will return to showing the current CHANNEL VISION up down buttons to the right hand side of the keypad The keypad can be controlled from the A0505 remote control see the section titled Using the A0505 remote control for more details volume level Volume adjustments can be made using the e g e These four LEDs illuminate to indicate ABUS Si e The Pwr button is used for source selection which source input is selected Jumper Settings Jumper settings determine how the AB 134 will react under various circumstances These jumpers should be set to the desired configuration before the AB 134 is installed If you need to make changes to the jumper settings the AB 134 MUST BE DISCONNECTED from the system first Jumper setting functions explained Volume Preset This jumper sets the starting volume of the keypad will be when it is turned on If the jumper is on pins 1 amp 2 the volume will always be set at the default level when the AB 134 is turned on If the jumper is on pins 2 amp 3 the volume will be at the same level as it was before the AB 134 was turned off Status is active when the zone is on and audio is present Status will go dormant when audio is not
Download Pdf Manuals
Related Search