GT16 Backlight for 12.1"/10.4" GOT User`s Manual
Contents
1. For relevant manuals refer to the PDF manuals stored in the CD ROM for the drawing software used Specifications Item GT16 GT16 GT16 GT16 GT16 80SLTT 7OSLTT 7OVLTT 70VLTTA 70VLTN Type Cold cathode tube backlight 50 000h or more irg Operating ambient temperature 25 C Weight 0 015kg 0 008kg 0 010kg 0 012kg 9 0 033Ib 0 018Ib 0 022Ib 0 026Ib 2008 MITSUBISHI ELECTRIC CORPORATION 3 BACKLIGHT REPLACEMENT 3 1 Preparing for Replacement The GOT includes the backlight for the liquid crystal display panel The backlight intensity decreases with time Replace the backlight when the display section becomes dark due to the decreased intensity and the picture is unclear The following shows the procedures for replacing the backlight 1 Turn off the GOT 2 Disconnect the power supply cable and the communication cable Remove the GOT from the control panel 3 Remove the right extension unit cover of the GOT Remove an extension unit including a bus connection unit if it is mounted 4 Remove eight fixing screws on the GOT rear face with a screwdriver 3 2 Replacing Backlight 1 GT16 80SLTT GT16 70SLTT GT16 70VLTT 1 Remove the cable connector of the backlight from the connector of the GOT board Expanded figure of part A in 3 1 4 When replacing the GT16 70SLTT 70VLTT remove the cable2. MITSUBISHI GT16 Backlight for 12 1 10 4 GOT User s Manual GT16 80SLTT GT16 70SLTT GT16 70VLTT GT16 70VLTTA GT16 70VLTN Thank you for purchasing the GOT1000 Series Prior to use please read both this manual and detailed manual thoroughly to fully understand the product MODEL GT16 80SLTT U MODEL CODE 1D7M83 IB NA 0800428 D 1109 MEE GRAPHIC OPERATION TERMINAL GOTioo900 SAFETY PRECAUTIONS Always read these precautions before using this equipment Before using this product please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly The precautions given in this manual are concerned with this prod uct In this manual the safety precautions are ranked as DANGER and CAUTION Indicates that incorrect handling may cause 7 lt DANGER hazardous conditions resulting in death or severe injury Indicates that incorrect handling may cause A CAUTION hazardous conditions resulting in medium or slight personal injury or physical damage Note that the A CAUTION level may lead to a serious accident according to the circumstances Always follow the precautions of both levels because they are impor tant to personal safety Please save this manual to make it accessible when required and always forward it to the end user BACKLIGHT REPLACEMENT PRECAUTION
3. S lt gt DANGER Make sure to externally shut off all phases of GOT power supply when GOT is connected via the bus type connection make sure to shut off all phases of PLC CPU power supply as well and remove the GOT from the control panel before backlight replacement If all phases are not shut off it may cause an electric shock If backlight is replaced with the GOT on the control panel the GOT may drop off resulting in injuries CAUTION Make sure to wear gloves during backlight replacement Failure to do so may cause injuries Make sure to start the backlight replacement 5 or more minutes after power off of the GOT Failure to do so may cause burn injuries as the old backlight holds heat for a while STARTUP AND MAINTENANCE PRECAUTIONS CAUTION Before handling the GOT make sure to touch a grounded metal object to discharge the static electricity from the human body Failure to do so may cause the GOT to fail or malfunction DISPOSAL PRECAUTIONS CAUTION Dispose of this product as industrial waste TRANSPORTATION PRECAUTIONS CAUTION Make sure to transport the GOT main unit and or relevant unit s in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specifications of the GT16 User s Manual as they are precision devices Failure to do so may cause the unit to fail Check if the unit operates correctly after transpo
4. d Shanghai 200003 China Tel 86 21 6120 0808 Taiwan Setsuyo Enterprise Co Ltd 6F No 105 Wu Kung 3rd Rd Wu Ku Hsiang Taipei Hsine Taiwan Tel 886 2 2299 2499 Korea Mitsubishi Electric Automation Korea Co Ltd 1480 6 Gayang dong Gangseo ku Seoul 157 200 Korea Tel 82 2 3660 9552 Singapore Mitsubishi Electric Asia Pte Ltd 307 Alexandra Road 05 01 02 Mitsubishi Electric Building Singapore 159943 Tel 65 6470 2460 Thailand Mitsubishi Electric Automation Thailand Co Ltd Bang Chan Industrial Estate No 111 Moo 4 Serithai Rd T Kannayao A Kannayao Bangkok 10230 Thailand Tel 66 2 517 1326 Indonesia P T Autoteknindo Sumber Makmur Muara Karang Selatan Block A Utara No 1 Kav No 11 Kawasan Industri Pergudangan Jakarta Utara 14440 P O Box 5045 Jakarta 11050 Indonesia Tel 62 21 6630833 India Messung Systems Pvt Ltd Electronic Sadan NO III Unit No15 M I D C Bhosari Pune 411026 India Tel 91 20 2712 3130 Australia Mitsubishi Electric Australia Pty Ltd 348 Victoria Road Rydalmere N S W 2116 Australia Tel 61 2 9684 7777 MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN NAGOYA WORKS 1 14 YADA MINAMI 5 CHOME HIGASHI KU NAGOYA JAPAN When exported from Japan this manual does not require application to the Ministry of Economy Trade and Industry for service transaction permission Specifications subject to chan
5. e sure not to damage the sheaths of the cables Insert the backlight until you do not see its top plate Insert the top plate of the backlight here 5 Connect the backlight cable connector to the relay cable connector Do not put the cables of the backlight back to the cable holder Assemble the case in the reverse procedure of disassembly Tighten the fixing screws on the GOT rear face with a torque of 0 36 to 0 48 Nem When installing the case make sure that the cables are not stuck between the case and the GOT Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi machine damage or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties A For safe use This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if
6. ge without notice Printed in Japan September 2011
7. ow with the screwdriver or others and pull out the backlight to the left Pull out the backlight so that the backlight does not hit the packing Packing Fluorescent tube 3 Install a new backlight in the reverse procedure of removal When inserting a new backlight into the backlight replacement hole of the GOT make sure not to damage the sheaths of the cables Insert the backlight until it is fixed by the latch black Assemble the case in the reverse procedure of disassembly Tighten the fixing screws on the GOT rear face with a torque of 0 36 to 0 48 Nem When installing the case make sure that the cables are not stuck between the case and the GOT 3 GT16 70VLTTA 1 Remove the backlight cable connector from the relay cable connector Since the connected connectors adhere inside the GOT detach the connected connectors and perform the removal Expanded figure of part A in 3 1 4 2 Remove the backlight cables from the cable holder by pulling the backlight cables one by one in the arrow direction and then in the arrow direction Cable holder 3 Pull out the backlight so that the backlight does not hit the packing Zz Fluorescent tube Packing 4 Install a new backlight so that its top plate is inserted between the metal parts of the backlight replacement hole When inserting a new backlight into the backlight replacement hole of the GOT mak
8. rtation Packing List After unpacking the box check that the following products are included Model Product Quantity GT16 80SLTT GT16 70SLTT GT16 70VLTT Backlight 1 GT16 70VLTTA GT16 70VLTN 1 OVERVIEW This User s Manual describes GT16 backlight for 12 1 10 4 GOT hereinafter referred to as the backlight For applicable GOTs refer to GT16 User s Manual Product Model Description GOT For 12 1 TFT SVGA GT16 aoe f 80SLTT of high intensity and GT1685M S wide angle view GT16 For 10 4 TFT SVGA TOSLTT of high intensity and GT1675M S wide angle view For 10 4 TFT VGA of Backlight GT16 high intensity and wide GT1675M V t 7OVLTT A angle view GT16 For 10 4 TFT VGA of 5 7OVLTTA high intensity and wide GT1675M V angle view GT16 k GT1675 VN 7ovitn For 10 4 TFT VGA GT1672VN 1 Function version C or earlier 2 Function version D or later 2 SPECIFICATIONS The following shows the performance specifications of the backlight The general specifications of the backlight are the same as those of the GOT For the general specifications of the GOT refer to GT16 User s Manual Manuals The following shows manuals relevant to this product Detailed Manual Manual number Manual name Model code GT16 User s Manual SH 080778ENG Sold separately 1D7M88 Relevant Manuals
9. s from the cable holder When replacing GT16 70SLTT VLTT 2 Press the backlight fixing latch black toward the direction of the following arrow with the screwdriver or others and pull out the backlight to the left Pull out the backlight so that the backlight does not hit the packing When replacing GT16 80SLTT When replacing GT16 70SLTT VLTT Fluorescent tube Packing The latch is on the right side of the backlight Edge on view figure of the part A in 3 1 4 sm laa Press the latch toward the direction of the following arrows with the screwdriver or others ZZ Packing Fluorescent tube 3 Install a new backlight in the reverse procedure of removal When inserting a new backlight into the backlight replacement hole of the GOT make sure not to damage the sheaths of the cables Insert the backlight until it is fixed by the latch black Assemble the case in the reverse procedure of disassembly Tighten the fixing screws on the GOT rear face with a torque of 0 36 to 0 48 Nem When installing the case make sure that the cables are not stuck between the case and the GOT 2 GT16 70VLTN 1 Remove the cable connector of the backlight from the connector of the GOT board Expanded figure of part A in 3 1 4 2 Press the backlight fixing latch black toward the direction of the following arr
10. the product fails install appropriate backup or failsafe functions in the system Country Region Sales office Tel USA Mitsubishi Electric Automation Inc 500 Corporate Woods Parkway Vernon Hills IL 60061 U S A Tel 1 847 478 2100 Brazil MELCO TEC Rep Com e Assessoria Tecnica Ltda Rua Correia Dias 184 Edificio Paraiso Trade Center 8 andar Paraiso Sao Paulo SP Brazil Tel 55 11 5908 8331 Germany Mitsubishi Electric Europe B V German Branch Gothaer Strasse 8 D 40880 Ratingen GERMANY Tel 49 2102 486 0 U K Mitsubishi Electric Europe B V UK Branch Travellers Lane Hatfield Hertfordshire AL10 8XB U K Tel 44 1707 276100 Italy Mitsubishi Electric Europe B V Italian Branch Centro Dir Colleoni Pal Perseo Ingr 2 Via Paracelso 12 I 20041 Agrate Brianza Milano Italy Tel 39 039 60531 Spain Mitsubishi Electric Europe B V Spanish Branch Carretera de Rubi 76 80 E 08190 Sant Cugat del Valles Barcelona Spain Tel 34 93 565 3131 France Mitsubishi Electric Europe B V French Branch 25 Boulevard des Bouvets F 92741 Nanterre Cedex France Tel 33 1 5568 5568 South Africa Circuit Breaker Industries Ltd Private Bag 2016 ZA 1600 Isando South Africa Tel 27 11 928 2000 Hong Kong Mitsubishi Electric Automation Hong Kong Ltd 10th Floor Manulife Tower 169 Electric Road North Point Hong Kong Tel 852 2887 8870 China Mitsubishi Electric Automation China Ltd 4 F Zhi Fu Plazz No 80 Xin Chang Roa
Download Pdf Manuals
Related Search