User Manual Cutting Tools - TFT
Contents
1. ASSEMBLING THE TOOL The operator must use the correct grinding tool for the task at hand Install the rotating file or disk Do not exert unnecessary force during this work Make sure that the equipment has the required marking in accordance with the ATEX DNV certificate Do not modify the tool without first contacting Safety Tools Allmet Do not use the tool until you are completely familiar with its operation The tool is to be earthed Use a antistatic hose with a steel wire Se DNV certificate for more information Do not use the equipment if it emits unusual sounds or if it vibrates or the speed varies Do not touch a rotating file ore disk during operations as this may lead to injury If you have long hair or wear loose garments be careful so as to avoid your hair or garment being caught in the equipment Make sure hair and garments is not near the rotating parts READY FOR USE Make sure that the grinding cutting tool is fitted with safety START STOP Verify that the air hose has been installed in accordance with current regulations This applies to all connections Inspect the hoses visually to ensure that they do not leak air Test the machine by using the tool for approx 30 seconds to make sure that everything has been correctly installed Before using review Water Control Box information on Page 16 amp 17 of this manual START UP OF ROTATING DISKs Wear mandatory personal safety equipment Make sure that you use the2. There is a risk of electrostatic discharge if used on plastic and other non conductive materials Workplace Hazards for misuse Slip Trip Fall is a major cause of serious injury or death Be aware of excess hose left on the walking or work surface High sound levels can cause permanent hearing loss Use hearing protection as recommended by your employer or occupational health and safety regulations Repetitive work motions awkward positions and exposure to vibration can be harmful to hands and arms If numbness tingling pain or whitening of the skin occurs stop using tool and consult a physician Air Supply and Connection Hazards for misuse Air under pressure can cause severe injury Always shut off air supply drain hose of air pressure and disconnect tool from air supply when not in use before changing accessories or when making repairs Never direct air at yourself or anyone else Whipping hoses can cause serious injury Always check for damaged or loose hoses and fittings Whenever universal twist couplings are used lock pins must be installed Do not exceed maximum air pressure of 6 3 bar 90 psig or as stated on tool nameplate Check and maintain air hoses regularly Use only Earthed Anti Static Hoses 2mm Maximum thickness on coatings See DMV information Make sure the air supply is clean and dry The ambient temperature for safe use must be greater than 0 C SAFETYTOOLS 4 SLLMNEE wale Supply and Connection Hazards
3. Attach air and water hose from Air tool to water outlet and air outlet o the control box Turn Water Outlet amp Water Inlet valves Adjustments approximately 1 16 of a turn counter clockwise open Hold Air Tool Trigger on and check flow of water flowing from the Water Nozzle to the Disk It should be a light spray Adjust water outlet adjustment valve to desired water flow Continue to hold the trigger on the Air Tool and gently adjust the Water Inlet Adjustment valve so that the Water Adjustment Gauge is set between 2 2 2 5 Bars Release Air Tool Trigger and wait for Water Adjust Gauge to drop to Zero The system is now set and ready for use Test by holding the Air Tool Trigger It may take a few second before Air tools goes with full throttle WATER ADJUST 19 Warnings SAFETYTOOLS 4 SLLMNEE Warning statements describe conditions which may lead to personal injuries including fatal injuries if the tool is not used properly and the warnings are not fully followed Caution statements describe conditions which may lead to equipment damage Warning Warning Warning Warning Warning Warning Warning Warning Warning Warning Warning Warning Warning Warning Caution Do not use this tool until you are completely familiar with the safe operation of the tool all accessories and safety devices Improper use can lead to severe injury This Manual defines proper use of thi
4. appropriate working posture The Cutting machine must be in operation when it is put down on the work place SAFETYTOOLS SLLMCLE Do not apply too much force while grinding or cutting This will increase the efficiency and lifespan of the motor amp disk Place the file on the work piece and pull it toward you Guide the file back and repeat the process until the desirable stripping has taken place The ambient temperature for safe use must be greater than 1 C In the event of change of equipment isolate the air supply before this is done In the event of protracted stops the air amp water supply is to be isolated and disconnected AFTER USE MAINTENACE Clean the Air engines Lubricate the air engines One drop of air motor oil into the air supply connector is optimal after prolonged use Clean the cutting tools Dry the cutting tools Place the tool in the safety suitcase securely Remove any grinding residues from the place of work Make sure that the safety suitcase is stored in an appropriate manner It is recommended to dismantle Safety Tools Air tools for overhauling and cleaning periodically after 500 hours of operation or once every six months Service of Safety Tools equipment should only be done by Safety Tools Allmet or an authorized Safety Tools agent Safety Tools Allmet Water Control Box should be serviced and maintained after 500 hours of operation Contact Safety Tools Allmet or the Authorized Agent in your region fo
5. rotating drive spindle and abrasive Rotation may continue for several seconds after the throttle has been released Do not lay the tool down until rotation has stopped Do not wear jewelry or loose clothing Choking can occur if neckwear is not kept away from tool and accessories Scalping can occur if hair is not kept away from tool and accessories Mounting Hazards for misuse Always shut off air supply relieve hose of air pressure and disconnect tool from air supply when changing accessories Always shut off water supply relieve hose of water pressure and disconnect tool from water supply when changing accessories Use only recommended sizes and types of abrasives Do not use files or disks that are cracked Correct mounting is necessary to prevent injury Safety Tools Air Tools are specially designed to work only with Safety Tools Cutting Disks Only Use Safety Tools Air Tools and Accessories as they are designed Do not use with other Accessories and or Air Tools Operating Hazards for misuse Operators and maintenance personnel must be physically able to handle the bulk weight and power of the tool Ensure that the work piece is properly supported Maintain a balanced body position and secure footing Avoid contact with rotating spindle and accessory to prevent cutting of hands and other body parts Wear protective equipment listed Do not use if vibration becomes excessive check the accessory for damage or incorrect mounting
6. Disk attach and remove instructions on pages 13 15 of this manual Water Control Box Both systems use water and air that flow through our Water Control Box A 0310 There are water adjustments that you set before each use These help regulate a consistent water flow between 2 amp 2 5 Bars When flow is set properly water use is approximately 6 liters per hour There are 4 gauges on top of the box e Water Inlet Water pressure in to the box 4 Bar minimum e Water Adjust Set using water adjustments on side of box see arrows above e Air Inlet 7 3 Bar Optimal e Air Adjust 6 3 Bar Maximum See Water Control Box operating instructions on page 15 18 of this manual TOOLS SLLMNEee Weld Seam Disk Mounting When attaching and removing the Weld Seam Disk A 503 to the A 0105 Air Tool you will need the following accessories e 6mm Allen Key e 22 mm Spanner not included e Vise with soft grip optional not pictured Below left picture Attach using gloved hands the Weld Seam Disk to A 0105 Safety Tools Ex Air Tool Screw Disk threads clockwise to put on and counter clockwise to take off the Weld Seam Disk After the Weld Seam Disk is attached examine the Guard for Weld Seam A0074 if needed adjusts using a Philips Screw Driver not included The guard should not be in contact with the Weld Seam Disk Make sure the Water Nozzle with Connecter A 0079 is secure and in place should not be in conta
7. TOOLS aLLmer 4 tatiana y 47 Certified Cutting Tools User Manual B I1 2 G c T4 Cutting Tools 112D c 101 _ ne coolest cutting edge T d chnology in the world A Y q ey ws w Cut the heat cut the risk a u U T N LLJ LLJ Se ffn A na Er ce e ot 2 U lt LLJ W Lo r Er i me on ae lt LLJ wp AA AW 12GcT4 Important Safety Information read before using Safety Tools Special Hazard Conditions for Misuse read before using Safety Tools Safety Preparation Safety Tools Ex Air Pneumatic Tools Information Cutting amp Weld Seam Equipment Overview Cutting amp Weld Seam System Weld Seam Disk Mounting Cutting Disk Mounting Water Control Box Setting the Water Control Box for use Safety Notices amp Warning Information SAFETYTOOLS 4 SLLMNEE ar Keep this manual in a safe accessible place at all times Keep this instruction manual for future reference Additional safety information may be available from the authorized agent in your country Consult them when necessary Do not remove or allow to become obscure any labels or markings on the tool A Important safety information Read these instructions fully before use Failure to do this may result in serious injury The user of this equipment must be competent in its use The user must ensure that the equipment is selected installed and used in acco
8. are not required unless it is known that plant air supply is likely to be contaminated It is recommended that oil is added to the tool after prolonged use See maintenance information SAFETYTOOLS 4 SLLMNEE Water Pressure Check hose size and water pressure The water pressure shall not exceed the maximum operating pressure of 2 5 bar The tool is designed for a optimum working pressure of 2 3 bar The water must be clean The installation of a filter is recommended For maximum efficiency and performance comply with the specification of the hose antistatic earthed hose Avoid the risk of whipping hose regularly check hose hose fitting and clamp conditions Always use a clean water hose and fittings and check that they are all in good condition and are properly installed Do not use damaged frayed or deteriorated hose end fittings Replace them when necessary Always store hoses properly A hose failure can cause injury The hose may come off and whip Use only earthed hosing in ATEX zones See DNV report Water should be supplied at a pressure greater than 4 Bar for maximum efficiency g Cutting Tempratures Safety Tools Allmet Explosive test were performed using a robotic system It is not possible using non machanical systems to reach high heat levels when the tools are used under human conditions The average temprature range when using Safety Tools Cutting equiptment is 25 C 45 C It is not possible to exceed 100 C T4 when us
9. ct with inside of Weld Seam Disk To complete the tightening of the Weld Seam Disk use the 22mm Spanner and the 6mm Allen Key e Place the 22mm Spanner on the inside sprocket of the Weld Seam Disk and hold firmly in place Insert 6mm Allen Key as shown in the picture to the left and firmly hand turn Allen Key counter clockwise The Weld Seam disk will tighten when used it needs to be only hand tightened with the Allen Key To remove the Weld Seam Disk reverses the process Only Trained and Certified people should remove or attach the Weld Seem Disk to the Air Tool Safety Tools also recommends wiping a little copper slip grease in the threads of the disk before and after use 13 TOOLS SLLMEEL Cutting Disk Mounting When attaching and removing the Cutting Disk A 0502 to the A 0105 Ex Air Tool you will need the following accessories e 6mm Allen Key e Cutting Disk Chuck Back A 0077a e Cutting Disk Chuck Front A 0077b e Chuck Key A 0206 Training required before use Step 1 Place Cutting Disk Chuck A0077 back view first on to the A 0105 Air Tool sprocket Make sure it is fit into the notched bolt extending out of the tool Training required before use Step 2 After the above step is completed the picture to the left is how your mounting should look There are 2 sprockets that extend out of the front face of the A0077a Chuck At this stage you are ready to put on the Cutting Dis
10. firm surface It may be used in other positions but it is important that the operator is in a secure position and has a firm grip and footing Refer to risk analysis for further guidance Safety Tools Allmet also has Robotic Systems and Automated Tool Guides Contact Safety Tools Allmet or the Authorized Agent in your Region for more information Protective Equipment Always wear necessary protective equipment when using this equipment Safety goggles or face shield gloves and hearing protection are required Ensure all clothing is close fitting to prevent becoming snagged in moving parts Safety Goggles face shield Mandatory Hearing Protection Mandatory Safety Gloves Mandatory Safety Hat Mandatory Respiratory Protection Optional SAFETYTOOLS 4 SLLMNEE special Conditions Projectile Hazards for misuse Always wear impact resistant eye and face protection when involved with or near the operation repair or maintenance of the tool or changing accessories on the tool Be sure all others in the area are wearing impact resistant eye and face protection Even small projectiles can injure eyes and cause blindness Use barriers to protect others from wheel fragments and grinding sparks Daily measure the air tool speed with a tachometer to make sure it is not greater than the RPM marked on the grinding accessory This Tool and its accessories must not be modified in any way Entanglement Hazards for misuse Keep away from
11. for misuse Water under pressure can cause severe injury Always shut off water supply drain hose of air pressure and disconnect tool from water supply when not in use before changing accessories or when making repairs Never direct water at yourself or anyone else Whipping hoses can cause serious injury Always check for damaged or loose hoses and fittings Whenever universal twist couplings are used lock pins must be installed Do not exceed maximum water pressure of 10 bar from water supply Check and maintain water hoses regularly Make sure the water supply is clean The ambient temperature for safe use must be greater than 0 Celsius Water may freeze on temperature close to 0 Celsius Make sure water dos not freeze before use Preparation Before Start up Make sure that the work station and the surroundings are safe and clear of any oil grease etc Make sure that there is sufficient space for the cutting tool and the task to be carried out Provide for the best access for air hoses Provide for the best access for water hoses Verify that the working pressure is 6 3 bar for the rotating Air engines Verify that the water pressure supply to the control box is above 4 bar WORKING POSITION Use the correct lifting technique Do not ever use the hose as a lifting handle Adopt a good stance and avoid overreaching Make sure that air hoses are fitted with whip checks Make sure that water hoses are fitted with whip checks
12. gives a very clean cut It works more like a milling tool than a cutting tool The special design of the cutting teeth and the hardness along with the slow rotation speed our air tool allow it to cut through very dense steel Cutting Disks can be re surfaced 3 to 4 times for 1 3 of the disk price SAFETYTOOLS SLLMEE ARMOURED HOSE The Armored Hose has both water and air incorporated into it See DNV Certificate for detailed information Prod nr E g A 0071 5 meters GUARD FOR CUTTING SYSTEM e A 0073 162 125 mm GUARD FOR WELDSEAM SYSTEM The Guard for Weld Seam System attaches to the Fuji Angle Grinder A 0105 with a Phillips head screwdriver In the corner there is a hole where the Water Nozzle Connector A 0079 is attached The Guard for Cutting System attaches to the Fuji Angle Grinder A 0105 with a Phillips head screwdriver In the corner there is a hole where the Water Nozzle Connector A 0079 is attached Prod nr 5S g A 0074 192 125 mm NOZZLE WITH CONNECTOR Water Nozzle with Connector is the water supply line incorporated into the hose system It should be screwed into the Guard before it is attached to the water supply hose A 0079 20 M6 0 6 MM SAFETYTOOLS SLLMEE CUTTING DISK CHUCK Back piece There are two Cutting Disk Chucks The Back Piece should be placed back view towards the Air Tool The two sprockets should face outward to
13. ing Safety Tools Cutting equipment under normal human conditions See DNV Certificate Safety Tools Ex Grinding Equipment is suitable for use in ambient temperatures Greater than 0 C to 40 C e Air supply must be dry amp clean e Water Supply should be clean filter recommended and above 4 bar gt Types of Steel Tested Safety Tools Allmet performed test on the 6 different materials three different steel qualities and two different titanium qualities below e Stainless Steel Grade 316 Steel ST52 Titanium ASTM B265 Titanium Austenitic Stainless Steel 6MO Maintenance To obtain maximum efficiency from the pneumatic tool preserve its features and avoid repeated repairs a routine inspection and repair program are recommended at least every 1000 hours the intervals between the various inspections depending on the amount of exertion on the power tool Safety Tools ATEX certified Air Tools must be properly maintained and tested by competent and trained personnel At any sign of malfunction or unusual behaviour the tool should be taken out of service for examination and repair If repairs are necessary contact the authorized agent in your country It is recommended to dismantle air tools for overhauling and cleaning after 500 hours of operation or once every six months e Before cleaning the tool for use make sure that it has been correctly assembled With all fasteners tightened e Check the rotation frequency of the tool without an a
14. k A 0502 Line up Cutting Disk with two sprockets and insert the disk into sprockets Make certain that that the Cutting Disk teeth are facing forward and down 14 TOOLS SILLME amp E Cutting Disk Mounting continued Step 3 After the Cutting Disk A 0502 is in place screw on Front Piece of the Cutting Chuck A 0077b back view facing the disk see page 11 Screw on clockwise by hand until tight Only Trained and Certified people should remove or attach the Weld Seem Disk to the Air Tool Step 4 After the Front Piece of the Cutting sprocket is hand tightened on you are ready to complete the tightening using the Allen Key and the Chuck Key Only Trained and Certified people should remove or attach the Weld Seem Disk to the Air Tool Step 5 To complete the tightening of the Cutting Disk use the Cutting Chuck Spanner and the 6mm Allen Key e Place the Cutting Chuck Spanner into the two holes of the front piece of the Cutting Chuck Insert 6mm Allen Key as shown in the picture to the left and firmly hand turn Allen Key counter clockwise Turn the Cutting Chuck Key clockwise with a firm strong grip To remove the Cutting Disk reverses the process 15 TOOLS SLLMEe Water Control Box Safety Tools Allmet sends out the Water Control box with Cejn Serie 310 1 4 inch BSP connectors outside threads These can be changes to meet your standards If you have any question contact Safety Tool
15. necessary to secure the work piece Only use this tool in well lit and ventilated areas If necessary wear respiratory Protection from dust created from the use of this tool Do not fit any damaged accessories to this tool Only use accessories in good condition free from visible cracks Use the correct tool Don t force tool or attachment to execute a task for which it is not intended 20
16. or shut off Trainining is required before using Safety Tools Cutting Equipment Safety Tools Allmet offers training at our office in Norway and offsite Training is also available through the Authorized Agent in your region See water control box information on page 16 18 of this Manual AN Disposal When disposing of components lubricants etc ensure that the relevant safety procedures are carried out Air Pressure Check hose size and air pressure The air pressure at the tool inlet with the grinder running shall not exceed the maximum operating pressure of 7 bars or lower if other specified The tool is designed for a working pressure of 6 3 bar 90 psig The compressed air must be clean The installation of a filter is recommended For maximum efficiency and performance comply with the specification of the air hose antistatic earthed hose Avoid the risk of whipping hose regularly check hose hose fitting and clamp conditions Always use the correct and clean air hose and fittings and check that they are all in good condition and are properly installed Do not use damaged frayed or deteriorated hose end fittings Replace them when necessary Always store hoses properly A hose failure can cause injury The air hose may come off and whip Use only earthed hosing in ATEX zones See DNV report Air should be supplied at a constant pressure of 6 3 Bar at the tool with the trigger fully depressed In Line lubricators and air filters
17. r Water Control Box Maintenance information SAFETYTOOLS Cutting amp Weld Seam Equipment Overview WATER CONTROL BOX A 0310 FUJI ANGLE GRINDER ra vA 5 sy 6 A 0105 1000rpm FCD 10X 52 2400 1 4 NPT Weldsem disk FG R VY g A gt ip ro pn x Y aes Wa 7 W ae Y A 0503 0x10 mm Cutting Disk a 110x5mm A 0502 652 SLLMEeeL The Water Control Box is used to regulate the flow of air and water There are internal regulators amp filters that help to keep a consistent flow Settings must be adjusted prior to each use On top there are 4 gauges Water Inlet Water Adjust Air Inlet amp Air Adjust These need to be set according to the information on page 16 amp 17 in this manual Training is required prior to using through Safety Tools or the authorized agent in your region The Fuji Angle Grinder A 0105 has special guards that are attached to for both the Cutting amp Weld Seem Disks When used with the Cutting Disk there are also two special chucks that are used to hold the disk firmly in place This Angle grinder is the same machine we use with our Grinding Disk for Paint The Weld Seam Disk is 10mm thick On many of the jobs our clients use this disk in combination with our Cutting Disk at a 45 degree angle Weld Seam Disks can be re surfaced 3 to 4 times for 1 3 of the disk price The Cutting Disk is 5mm thick and
18. r minimum e 10 Bar maximum The Water Adjust Gauges need to be adjusted between 2 2 to 2 5 for the Air Tool to operate If the water pressure goes below 2 bars the tool will automatically shut off If the water pressure goes above 3 bars the tool will automatically shut off Air Gauges e Air Inlet 7 3 Bars Optimal e Air Adjust 6 3 Bars Maximum The Oil Refill is also on the top of the box Only Trained and Certified people should operate Safety Tools Allmet Water Control Box 17 TOOLS p SLLMNEee Water Control Box Oil Refill Remove and replace with 6mm Allen Key Oil should be checked before use and monitored Fill with Air tool oil see picture below Only Trained and Certified people should operate Safety Tools Allmet Water Control Box Water amp Oil Monitoring On one side of the Water Control Box This is where you monitor excess water in the box and check Air Tool Oil level Only Trained and Certified people should operate Safety Tools Allmet Water Control Box Setting the Water Control Box for use Only Trained and Certified people should operate Safety Tools Allmet Water Control Box 18 TOOLS p SLLMNEe Setting the Water Control Box for use Make sure Water Drain valve is closed l i di B e Turn Water Inlet Adjustment valve P pete clockwise until closed r Turn Water Outlet Adjustment valve DNN E clockwise until closed 3 4 i Attach Air amp Water hoses to Inlets e
19. rdance with regulations and is checked fully before use The equipment must only be used for its intended purpose and be maintained regularly Safety is a primary consideration when using Safety Tools equipment The tools should be used in the correct way with a good understanding of how to use the tools safely The tools together with attachments and accessories should only be used for the purpose for which they are designed Safety devices and accessories supplied should be used appropriately Do not use outside the design intent unless first agreeing upon such use with the manufacturer and or authorized agent Read and fully understand all the instructions before attempting to install use service or maintain the equipment Training is available through Safety Tools Allmet and the authorized agent in your region Training from Safety Tools Allmet and or the Authorized agent in your region is required prior to using Safety Tools Cutting amp Weld Seem Removal tools A WARNING To reduce the risk of injury before using or servicing tool read and understand the following information The features and descriptions of our products are subject to change without prior notice This product is designed for cutting amp removing material using abrasives The abrasives are very hard and solid 9 7 Rockwell scale No other use permitted for professional use only Before servicing of the pneumatic tool the supply of compressed air must be disconnected
20. s Allmet or the authorized agent in your region Only Trained and Certified people should remove or attach the Weld Seem Disk to the Air Tool Adjustments amp Inlets On one side of the Water Control Box there 1s Water Inlet Adjustment controls water flow in Water Outlet Adjustment regulates water flow Water Drain Drains excess water o Use before and after set up to drain water Water Inlet Connect water into box Air Inlet Connect water into box Only Trained and Certified people should remove or attach the Weld Seem Disk to the Air Tool Air amp Water Outlets On the opposite side of the Water Control Box there is the Air amp Water outlet This is where the hose s from the T4 Ex Air tool is connected Connect the water before the air e Air Outlet Air flows from Water Control Box to Air Tool e Water Outlet Water flows form Water Control Box to lubricate Cutting amp Weld Seam Disk Only Trained and Certified people should remove or attach the Weld Seem Disk to the Air Tool 16 TOOLS p SLLMNEe Water Control Box Gauges There are 4 gauges on top of the Water Control Box e Water Inlet 4 Bar minimum e Water Adjust 2 2 2 5 Bars o Use water adjustments valves on side to set e Air Inlet 7 3 Bar Optimal e Air Outlet 6 3 Bar Maximum Only Trained and Certified people should operate the Water Control Box Water Gauges The Water pressure into the box needs to be e 4 Ba
21. s equipment Before using this tool for any other use please consult the manufacturer Please consult your dealer if you you do not understand any part of this manual or operating procedure for this tool Always shut off and disconnect the tool from the energy source when not in use or left unattended for any time The air in the tool and supply hose should be discharged prior to disconnecting from the energy source Do not lay the tool down until all rotating parts have come to a complete stop The tool should be earthed via proper connection to a certified air hose All air hose connections should be secured using whip check restraining devices Do not exceed the maximum air pressure Always use safety goggles with this tool Ordinary safety spectacles are not suitable Full face shields may also be used Use gloves at all times when using this tool Gloves should be suitable for the task Adding unsuitable accessories can create hazards Use accessories or attachments only in accordance with the operating instructions Do not wear loose clothing whilst operating this tool Neckties rings bracelets or other jewellery may get caught in the tool and should be removed or covered Good non slip footwear is recommended Wear protective hair covering to contain long hair Keep a good footing and balance at all times Don t overreach A rotating wheel can catch an article of clothing and cause personal injury Secure work Use clamps if
22. ttached disk After each maintenance or service e f you are uncertain about the correct way to service a tool contact the authorized agent in your region e Only trained people should service and maintain Safety Tools equipment See water control box information on page 16 18 of this Manual Check the free speed of the tool at regular intervals and after each operation or maintenance task Remove the disk to check the speed The maximum allowed speed shown on the tool must not be exceeded and the vibration level must not be excessive SAFETYTOOLS SLLMEE Motor speeds These cold grinding tools are designed for use with the following motors Motor type RPM Maxair pressure __ Air hose diameter A 0105 FujiFCD 10X 52 special 1000 6 3 Bar 9 5mm 3 8 inch a The operator must wear ear protection when the noise level at his position exceeds 83dB or 85 GB It is recommended that the operator wears the ear protector even if the noise level is less than 83dB or 85 dB Noise levels while grinding with Safety Tools Equipment e Lowest reading is 80 dB e Highest reading is 85 dB e Average reading is 80 5 dB J Vibration Analysis HAV Averaged measurements while grinding with one of the Cutting Disk amp Weld Seem Disk mounted on Grinding amp Cutting was done on a 10 mm carbon steel plate thal i Posture Safety Tools are generally used as a hand held unit It is recommended that it is used whilst standing on a
23. wards the Cutting Disk N Front view F Back view A 0077a 42 x10 mm CUTTING DISK CHUCK Front piece The Front Piece of the Cutting Disk Chuck is attached after the Cutting Disk The back view should be faced towards the Cutting Disk Use the Chuck Key to tighten Back view Front view A 0077b 42x10 mm CHUCK KEY The Chuck Key is used to tighten the front piece of the Cutting Chuck Insert the two sprockets into the front piece of the Cutting Disk Chuck and turn clockwise to tighten and counterclockwise to loosen Use the Allen Key in unison with force applied in the opposite direction when putting on and taking off A 0206 226 200 X 30 mm ALLAN KEY 6mm 6mm Allen Key is used to in unison with the Chuck Key force should be applied in the opposite direction when counterclockwise putting on and clockwise when taking off the Cutting Disk Chuck front piece A 0207 th TOOLS p SLLMEee Cutting amp Weld Seam System a oes y Pi x i ma o v ME r Safety Tools Air Tools Cutting Disk amp Weld Seam Disk Safety Tools Allmet has two Disks that attach to our Ex Air Tool A 0105 A Cutting Disk A 0502 and a Weld Seam Removal Disk A 0503 Both disks have separate safety Guards that are attached to the Air Tool see page 10 Both disks also are attached with a different method See page 13 for the Cutting Disk and page 14 for the Weld Seam Disk See Cutting amp Weld Seam
Download Pdf Manuals
Related Search