Manual - Enovate Medical
Contents
1. Charge Capacity 0 10 11 25 26 50 51 75 76 100 Power System MANUAL MOBIUS POWER QUICK REFERENCE GUIDE Q When do I need to change the Mobius Power Battery Pack TIME REMAINING ON BATTERY PACK Calculating The workstation is calculating the run time based on Remaining Time the current being drawn by the system Once the time is calculated the Battery Pack will show 08 25 a continuous display of Time Remaining in hours and Remaining Time minutes With Nurse Sensor installed the time will vary depending on usage amount LOW BATTERY WARNING CYCLE 25 minutes time remaining Low LCD displays Low Battery Battery Audible alarm single beep will alert you every 100 seconds 20 minutes time remaining Low LCD displays Low Battery Battery Audible alarm double beep will alert you every 75 seconds 15 minutes time remaining Replace LCD displays Replace Battery Battery Audible alarm two beeps will alert you every 50 seconds 10 minutes time remaining Replace LCD displays Replace Battery Battery Audible alarm single beep will alert you every 20 seconds 5 minutes time remaining System LCD displays System Shutdown Shutdown The Mobius SD application is doing an orderly shutdown of Windows because the battery charge level is very low Once the Battery Pack charge capacity is2. First Edition MEDICAL DEVICE DIRECTIVE 93 42 EEC EUROPEAN UNION EU TESTING AND REPORT SERVICES e CENELEC EN 60601 1 Medical Electrical Equipment Part 1 General Requirements for Safety Incorporates Corrigendum July 1994 Includes Amendments A1 1993 A11 1993 A12 1993 A2 1995 and A13 1996 IEC 601 1 1988 A1 1991 A2 1995 Corrigendum 1995 Modified e IEC 60601 1 2 2001 09 Medical Electrical Equipment Part 1 2 General Reguirements for Safety Collateral Standard Electromagnetic Compatibility Reguirements and Tests Second Edition CB SCHEME REPORT AND CERTIFICATE e IEC 60601 1 Medical Electrical Equipment Part 1 General Requirements for Safety Second Edition IMPORTANT WARNINGS MANUAL Cart Features MANUAL EMI Electromagnetic Interference Ove rview Portable and mobile RF communications equipment can affect Medical Electrical Equipment The use of accessories transducers and cables other than those specified by the manufacturer may result in increased Emissions or decreased Immunity of the System The System should not be used adjacent to or stacked with other equipment and that if adjacent or stacked use is necessary the System should be observed to verify normal operation in the configuration in which it will be used LCD Message Center 2 Battery Charging Station Battery Holster 4 Battery Charging Station Charger Board Inside Charging Indicator Light Main Power Controller Main Co
3. declaration electromagnetic emissions for all EQUIPMENT and SYSTEMS see 6 8 3 201 a 3 Guidance and Manufacturer s declaration electromagnetic emissions MOBIUS POWER is intended for use in the electromagnetic environment specified below The customer or the user of MOBIUS POWER should assure that it is used in such an environment Emissoins P Electromagnetic environment guidance Compliance Test RF emissions Group 1 MOBIUS POWER uses RF energy only CISPR 11 for its internal function Therefore its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment RF emissions Class A CISPR 11 MOBIUS POWER is suitable for use in all Harmonicemissiohs Not establishments other than domestic and oni issi those directly connected to the public IEC 61000 3 2 Applicable low voltage power supply network that Voltage fluctuations Not ees used for domestic flicker emissions IEC Applicable purp 61000 3 3 Table 206 Recommended separation distances between portable and mobile RF communi cations equipment and the EQUIPMENT or SYSTEM for EQUIPMENT and SYSTEMS that are not LIFE SUPPORTING see 6 8 3 201 b Recommended separation distances between portable and mobile RF communications equip ment and the MOBIUS POWER MOBIUS POWER is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled The customer or the user of MOBI
4. employ the use of symbols with or without accompanying text Health products regulatory agencies require the use of symbols often in place of textual statements to enhance the legibility of labeling and thus improve the conspicuousness of required information such as important safety information Your attention to the presence and content of symbols used in this manual will help to ensure the safe use of your Enovate Medical cart The following chart depicts the symbols used and provides a definition for each symbol found in this manual and in the labels and labeling materials of the Enovate Medical cart Distributed by Enovate Medical US Headquarters 1152 Park Avenue Murfreesboro TN 37129 Support denovatemedical com Toll free 888 909 8930 IMPORTANT WARNINGS MANUAL The term symbols refers to the use of graphical symbols without equivalent accompanying text Symbols are used by medical device manufacturers to create uniform labels and labeling for the United States European Union and any other countries that may permit their use in medical products By using symbols in place of some textual statements manufacturers may enhance the legibility of labeling and thus improve the conspicuousness of required information especially where information is contained upon product labels that are restricted in their space available The use of symbols on the product labels are intended to conform to international consensus standards Th
5. 3 Hz 2 A rms for 115 VAC 1 A rms for 230 VAC 12VDC 11A Less than 7hrs 9 6 Hx 4 1 Wx 7 5 D System Electromagnetic 20 Emissons MEDICAL ELECTRICAL EQUIPMENT needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided in the ACCOMPANYING DOCUMENTS WARNING Use of unapproved ACCESSORIES may result in degradation Guidance and Manufacturer s Declaration Cables Transducers and Accessories The listed cables transducers and accessories have been determined by Enovate Medical to be compliant with the emissions and immunity requirements of IEC 60601 1 2 2001 Part No Description Max Shielded Possible Y N Length 8115196 Cable power 2 5 x 5 5 Kycon KPP 84 Y 8115197 Cable power 2 1 x 5 5 Kycon KPP 84 Y 8115198 Cable power Hirose A Kycon KPP 84 Y 8115199 Cable power Kyron Kycon KPP 84 Y 8115200 Cable power 3 pin din Kycon KPP 84 Y 8115201 Cable power Kyron Kycon KMDLA 84 Y 8115202 Cable power Dell combo power adapter 84 Y 8115203 Cable power 1 7 x 4 75 Kycon KPP 84 Y 8115204 Cable power 2 5 x 5 5 locking barrel Kycon KPP 84 Y 8115275 Cable serial for basic fuel board 72 Y 8115360 Cable 10 pin ribbon extension 18 N 8114206 Cord Reel IEC 48 pigtail 908 Ametek 10 N 8116246 Cord Reel IEC 48 pigtail 908 KeTe 10 N Table 201 Guidance and manufacturer s
6. 80 MHz field strength should be less than 3 V m 23 25 enovate MEDICAL 1152 Park Avenue Murfreesboro TN 37129 p 888 909 8930 f 615 896 1652 www enovatemedical com support enovatemedical com 2013 Enovate Medical LLC All Rights Reserved
7. IUS POWER Battery Pack BATTERY DISPOSAL Industrial batteries contain materials which are considered hazardous substances If batteries are improperly disposed of for example thrown in the trash or illegally dumped these substances can eventually leak out and contaminate the surrounding soil and groundwater supply It is a violation of federal law to improperly dispose of batteries once they can no longer be used Once a battery is purchased full liability and responsibility lies on the owner to dispose of the battery The law says that responsibility is still on the owner if the bat tery is disposed of improperly by dumping in a landfill or shipping to a scrap dealer who does not handle it properly and in which environmental damage occurs It is illegal to dispose of batteries in any way other than thermal recovery or recycling of the hazardous substances in batteries according to the Environmental Protection Agency EPA The Department of Transportation DOT has strict guidelines for the shipping of haz ardous materials which result in large fines if they are not followed Check with your local ordinances for proper disposal procedures MSDS sheets are available on line at http www enovatemedical com Batteries are consumable goods Recycling MOBIUS POWER Batteries Rechargeable batteries power everything from portable phones and cordless phones to laptops and PDAs Batteries are a unique product comprised of heav
8. STATION SPECIFICATIONS Dual Charging Station y y Quad Charging Station Four Year Battery e Lithium lon LiCo02 e 26 AH e All cross compatible e Charge Time 26AH lt 4hrs e Measurements 10 H x 5 W x 3 14 D e Weight 4 8lbs e Standard 110 VAC Outlet e Protection 15A 250V e Input Voltage 120V 10 e Input Frequency 60Hz e Input Current 3 6 Amps max e Output Voltage 12 6 VDC e Output Current 8 5 A per bay max e Output Power 110 Watts max per bay e Measurements 12 6 H x 17 W x 5 8 D 110 Watts max per bay 12 6 H x 27 W x 5 8 D e Standard 110 VAC Outlet e Standard 15 AMP Breaker e Input Voltage 120V 10 e Input Frequency 60Hz e Input Current 7 2 Amps max e Output Voltage 12 6 VDC e Output Current 8 5 A per bay max e Output Power e Measurements 18 Power System MANUAL MAIN CONTROLLER SPECIFICATIONS Power Controller HOLSTER SPECIFICATIONS Holster Charger Model Input Voltage Input Frequency Input Current Output Voltage Current Charge Time Measurements Overload Protection Yes e Output Voltage 2 Channels variable 5 VDC 12 VDC e Output Voltage 2 Channels variable 12 VDC 24 VDC e Input Voltage 11 1 VDC nominal e Input Voltage Range DC 9 6 12 6V e Input Current 14 9 max e Output Protection Yes e Output Power 115W Total for System e Overload Recovery Yes Protek Power PMP150 12 HI 110 240 VAC 47 6
9. US POWER can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment transmitters and MOBIUS POWER as recommended below according to the maximum output power of the communications equipment Separation distance according to frequency of transmitter m Rated maximum output power of transmitter 150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2 5 GHz W d 3 5 VileP d 3 5 E1 eP d 7 E1 eP 0 01 0 12 0 12 0 23 0 1 0 38 0 38 0 73 1 1 2 1 2 2 3 10 3 8 3 8 7 3 100 12 12 23 For transmitters rated at a maximum output power not listed above the recommended separation distance d in meters m can be estimated using the eguation applicable to the freguency of the transmitter where P is the maximum output power rating of the transmit ter in watts W according to the transmitter manufacturer NOTE 1 At80 MHz and 800 MHz the separation distance for the higher frequency range applies NOTE 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people 21 Power System MANUAL 22 Table 202 Guidance and manufacturer s declaration electromagnetic immunity for all EQUIPMENT and SYSTEMS see 6 8 3 201 a 6 Guidance and manufacturer s declaration electromagnetic immunity MOBIUS POWER is intended for use in the electromagnet
10. ational error occurs the plug should be immediately removed from the socket THE MAINS SOCKET SHOULD BE EASILY ACCESSIBLE If an extension cord must be used ensure it is rated for the power capacity of the unit THIS CHARGER IS DESIGNED FOR USE WITH LITHIUM POLYMER BATTERIES For safety reasons this charger must be used only for batteries which have the right number of cells in series Output divided by 4 1V or 4 2V DO NOT OPEN THE POWER SYSTEM Unauthorized personnel opening the power system may cause injury and or death If the unit is not working properly please contact Enovate Medical at 888 909 8930 DO NOT USE THE UNIT IN NEAR WATER OR OTHER LIQUIDS If the unit becomes wet unplug it immediately wipe away any excess liquid and allow it to dry before use Failure to do so may cause electric shock damage to the unit voiding of warranty injury or death ALWAYS KEEP THE UNIT WELL VENTILATED Do not block ventilation airways or insert items into the ventilation slots Failure to do so can cause the power system to overheat and possibly cause fire explosion and or death THE CHARGER CONTAINS DANGEROUS VOLTAGES AND THE COVER SHOULD NOT BE REMOVED All service or maintenance work should be carried out by qualified service personnel by contacting Enovate Medical at 888 909 8930 PPEP re e IMPORTANT WARNINGS MANUAL SAFETY GUIDELINES MOBIUS POWER is designed to ensure both the highest level of product quality and safety fo
11. depleted the LCD Message Center will turn off At this point MOBIUS POWER your computer and any other devices requiring power will shu lown until the Battery Pack is replaced with a Fully Charged Battery Pack OR the Battery lolster is plugged into an AC outlet using the optional Holster Charger You may then turr your computer and other electronic dev Power System MANUAL Power System MANUAL MOBIUS POWER Charging Station Includes 2 Battery or 4 Battery Charging Stations Once the Charging Station is placed U and plugged into an outlet slide a Battery Pack into any open slot making sure the FLASHING GREEN indicator light turns on The charge cycle is complete when the indicator light is illuminated SOLID GREEN FULLY CHARGED Solid green light CHARGING Blinking green light ERROR Solid or blinking yellow light MOBIUS POWER Holster Charger Use of the Holster Charger reguires two connections One end connects to the Battery Holster on your mobile cart and the other to an AC electrical outlet After you connect the Holster Charger to both the Battery Holster and the electrical outlet the LCD will read AC Powered Charge status can be checked by unplugging the Holster Charger from the wall outlet and reading the Time Remaining on the LCD or use the LEDs on the Battery Pack Please refer to next page forthe explanation of how to read the LEDs on each individual MOB
12. e following chart depicts the symbols used and provides a definition for each symbol found in the labels CAUTION CONSULT ACCOMPANYING DOCUMENTS CONSULT INSTRUCTIONS FOR USE ELECTRIC SHOCK WARNING SYMBOL MANUFACTURER z SERIAL NUMBER CATALOG NUMBER TYPE B APPLIED PART AUTHORIZED REPRESENTATIVE IN THE EUROPEAN COMMUNITY gt EEE RE The CE mark on this product indicates it has been tested to and conforms with the provisions noted within the oN MN 93 42 EEC Medical Device Directive Accredited testing laboratory has evaluated a sample of the product and determined that it complies with applicable national standards lt enter as mimiek applicable Canadian and US gt Warnings N Important Warnings AN Electrical Shock Warning The above symbols represent safety warnings that require significant attention when seen on the EMC cart or in the user manual Failure to do so could result in minor injury major injury or even death Do not use in the presence of a anesthetic mixture with air or with oxygen or nitrous oxide USE A NONFLAMMABLE CLEANER WHEN CLEANING THE UNIT Failure to do so can result in death explosion and or fire DO NOT LEAVE THE UNIT UNATTENDED AROUND CHILDREN Failure to do so can result in injury and or death CAUTION THE POWER SYSTEM IS HEAVY You must use proper lifting techniques Failure to do so can result in injury AVOID USING AN EXTENSION CORD WITH THE UNIT If an oper
13. enovate lesa IM022 01 MANUAL 09 15 15 The Enovate Medical Slimline Cart was designed to set a new standard in quality Enovate Medical s goal is to provide a cart that is built right ready for years of use and backed by a commitment of exemplary service and support Thank you for purchasing the Enovate Medical Slimline Cart Distributed by Enovate Medical US Headquarters 1152 Park Avenue Murfreesboro TN 37129 Suppor t denovatemedical com Toll free 888 909 8930 For laptop compatibility please check with your local Enovate Medical Representative or call us toll free 888 909 8930 TABLE OF CONTENTS MANUAL WELCOME WARNINGS EMI OVERVIEW UNPACKING CART FEATURES POWER SYSTEM POWER SPECIFICATIONS SYSTEM ELECTROMAGNETIC EMISSONS IMPORTANT WARNINGS MANUAL Congratulations on your purchase of the Enovate Medical cart Please do not use your medical cart until you have read this manual in its entirety as it contains important safety and use information The Enovate Medical cart should only be used as outlined in this manual Be sure to keep the manual in a safe place for future reference If at any time you have guestions or concerns about the contents of this manual or the use of your Enovate Medical cart please contact Enovate Medical Customer Service toll free at 888 909 8930 This manual and the accompanying product labels and safety labeling materials of the Enovate Medical cart freguently
14. ic environment specified below The customer or the user of MOBIUS POWER should assure that it is used in such an environment Immunity test IEC 60601 test level Compliance level Electromagnetic environment guidance Electrostatic discharge ESD IEC 61000 4 2 6 kV contact 8 kV air 6 kV contact 8 kV air Floors should be wood concrete or ceramic tile Iffloors are covered with synthetic material the relative humidity should be at least 30 Electrical fast transient burst 2 kV for power supply lines 2 kV for power supply lines Mains power guality should be 2 kV common mode IEC 61000 4 4 1 kV for input 1 kV for input that of a typical commercial or output lines output lines hospital environment Surge 1 kV differen 1 kV differential IEC 61000 4 5 tial mode mode Mains power quality should be 2 kV common mode that of a typical commercial or hospital environment Voltage dips short inter ruptions and voltage varia tions on power supply input lines IEC 61000 4 11 lt 5 UT gt 95 dip in UT for 0 5 cycle 40 UT 60 dip in UT for 5 cycles 70 UT 30 dip in UT for 25 cycles lt 5 UT gt 95 lt 5 UT gt 95 dip in UT for 0 5 cycle 40 UT 60 dip in UT for 5 cycles 70 UT 30 dip in UT for 25 cycles lt 5 UT gt 95 dip Mains power quality should be that of a typical commercial or hospital e
15. ntrol Board and DC Boards Inside Son A Indicator Light Instructions on These limits are designed to provide reasonable protection against front of Charging Station harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio television or Medical Electrical Equipment reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference using one or more of the following measures reorient or relocate the receiving antenna increase the separation between the equipment and the receiver connect the equipment into an outlet on a circuit different from that which the receiver is connected consult the dealer or an experienced radio television technician for help The user must use shielded cables and connectors with this product AC Holster Power Adaptor OPTIONAL components or system upgrades uh U N Mobius Power Battery Pack Any changes or modifications to this product not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Operation is subject to the following two condition
16. nvironment If the user of the Mobius requires continued operation during power mains interruptions it is recommended that the Mobius be powered from an uninterruptible power supply ora battery dip in UT for in UT for 5 sec 5 sec Power Power frequency magnetic fields frequency should be at levels characteristic 50 60 Hz 3A m 3 A m 60Hz of a typical location in a typical magnetic field commercial or hospital IEC 61000 4 8 environment NOTE UT is the a c mains voltage prior to application of the test level Power System MANUAL Table 204 Guidance and manufacturer s declaration electromagnetic immunity for EQUIPMENT and SYSTEMS that are not LIFE SUPPORTING see 6 8 3 201 b Guidance and manufacturer s declaration electromagnetic immunity MOBIUS POWER is intended for use in the electromagnetic environment specified below The customer or the user of MOBIUS POWER should assure that it is used in such an environment Immunity IEC 60601 test Compliance Electromagnetic immunity test level level guidance Portable and mobile RF com munications equipment should be used no closer to any part of the MOBIUS POWER including cables than the recommended separation distance calculated from the equa tion applicable to the frequency of the transmitter Recommended separation distance d 3 5 V1 eP d 3 5 E1 eP 80 MHz to 800 MHz d 7 E1 eP 800 MHz to 2 5 GHz where P is the maximum outpu
17. ort and store this system within a temperature range of 329 F to 90 F 0 C to 32 C Pressure 500 hPa to 1060 hPa Humidity 20 RH to 95 RH non condensing IMPORTANT WARNINGS MANUAL IMRORTANT WARNINGS S MANUAL STORAGE REQUIREMENTS e The Battery Pack must not be fully charged prior to storing CLASSIFICATIONS e Charger Class 1 e Main Controller Class 1 Internally Powered e Degree of Protection against Harmful Ingress of Water IPXO e EQUIPMENT not suitable for use in the presence of a FLAMMABLE ANAESTHETIC MIXTURE WITH AIR or WITH OXYGEN OR NITROUS OXIDE ENVIRONMENTAL SPECIFICATIONS e Operating Temperature 25 C to 40 C e Relative Humidity 5 95 non condensing WARRANTY e Product Warranty 1 year limited warranty on Battery Packs and 2 years on electronic components e Extended Warranty 1 year optional extension available on electronic components e Contact Stinger MedicalEnovate Medical directly for full warranty details Approvals ETL CETL LISTING FOR NORTH AMERICA e UL 60601 1 UL Standard for Safety Medical Electrical Equipment Part 1 General Requirements for Safety First Edition e CSA C22 2 NO 601 1 M90 Issue 1990 01 11 R2001 Medical Electrical Equipment Part 1 General Requirements for Safety General Instruction No 1 Supplement 1 1994 Amendment 2 February 1998 R1997 e Information Technology Equipment Safety Part 1 General Requirements UL60950 1 First Edition e CAN CSA C22 2 No 60950 1 03
18. r the user To maintain both quality and safety follow the guidelines and instructions in this manual e Use the MOBIUS POWER system only as intended e Do not place the power system near a window Exposing the power system to rain water moisture or constant direct sunlight can severely damage it e The MOBIUS POWER system has no user serviceable internal parts To maintain your warranty refer all servicing to Enovate Medical qualified personnel e Do not cover or obstruct any venting holes on the MOBIUS POWER Main Power Controller or the MOBIUS POWER Charging Stations e Store the MOBIUS POWER system within 10 to 30 degrees Celsius 50 to 86 degrees Fahrenheit Storing the system outside the temperature range could result in permanent damage Use and maintain the cord set provided with the MOBIUS POWER Charging Stations e If any cord or cable is frayed or damaged replace it immediately with another of the same type and rating as supplied by Enovate Medical e To clean the exterior of the power system components follow the UL 60601 1 standard for use in a hospital environment See Cleaning Procedures for more information e Before cleaning a MOBIUS POWER Charging Station disconnect the enclosure from its power source e CAUTION Do NOT ship individual MOBIUS POWER Battery Packs by air Certain restrictions apply Contact Enovate Medical for shipping instruction TRANSPORT STORAGE e Care should be taken to transp
19. s 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation MOBIUS POWER meets or exceeds FCC Class A limits for EMI MOBIUSPOWER o ERROR Solid yellow light Cart Features MANUAL Cart Features MANUAL Unpacking Cart Features e MANUAL Cart Features e MANUAL Cart Features 609 NETO 1350 f L 17in QO wm A A Z X id E 7 N lt LU _ M i Adjustment Pedal n A Power Systems Each Battery Pack has a fuel gauge to indicate charge level capacity e You may check a Battery Pack s charge capacity at any time e To check the remaining charge on a Battery Pack press and release the white circle on the Battery Pack s fuel gauge display e The charge level is indicated in 25 increments by the number of status lights appearing between the E Empty and F Full e After 3 seconds the status lights will turn OFF MOBIUSPOWER STATUS ES EE U
20. t power rating of the transmitter in watts W according to the trans mitter manufacturer and d is the recommended separation distance in meters m Conducted 3Vrms RFIEC 150 kHz to 80 61000 4 6 MHz RadiatedRF 3V m IEC 61000 80 MHz to 2 5 4 3 GHz Field strengths from fixed RF transmitters as determined by an electromagnetic site survey a should be less than the compliance level in each frequency range b Interference may occur in the vicinity of equipment marked with the following symbol NOTE 2 These guidelines may not apply in all situations Electromagnetic propaga tion is affected by absorption and reflection from structures objects and people NOTE 1 At 80 MHz and 800 MHz the higher frequency range applies a Field strengths from fixed transmitters such as base stations for radio cellular cordless telephones and land mobile radios amateur radio AM and FM radio broad cast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which MOBIUS POWER is used exceeds the applicable RF compliance level above MOBIUS POWER should be observed to verify normal operation If abnormal performance is observed additional measures may be necessary such as reorienting or relocating MOBIUS POWER b Over the frequency range 150 kHz to
21. y metals which include nickel cadmium alkaline mercury nickel metal hydride and lead acid which can threaten our environment if not properly discarded or handled There are many ways to properly dispose of batteries most of which depends on the type of battery you have Lithium ion rechargeable batteries are less toxic than many others but it is still recommended that they be recycled The Rechargeable Battery Recycling Corporation RBRC manages a collection and recycling program for rechargeable batteries The RBRC accepts rechargeable nicad NiMH Lithium lon and small under 2 lb sealed lead acid batteries The RBRC has made it very convenient for you to recycle your rechargeables by getting retail stores like Home Depot Target Wal Mart and others to serve as collection points And it s all free of charge To find a drop off point near you in the US or Canada use the RBRC Locator tool at http www rbrc org call2recycle dropoff index php Remember Batteries enable our mobility so it s likely our society will be using a lot more batteries in the future But to ensure that we re not slowly poisoning our highly mobile selves it s important that we do a good job of recycling batteries Power System MANUAL Power Specifications BATTERY SPECIFICATIONS One Year Battery e Lithium lon LiCo02 e 26 AH e Allcross compatible e Charge Time 26AH lt 4hrs e Measurements 10 H x 5 W x 3 14 D e Weight 4 8lbs CHARGING
Download Pdf Manuals
Related Search