Untitled - Clipsal
Contents
1. IO Date The widget is used to select a date for controlling some aspect of the C Bus system The details of the usage will depend on the project The name of the controlled item is above the Widget start Date Reset A Short Press on the up or down arrows will change the column value by one A Long Press on the up or down arrows will cause the value to change continually until released When the desired value has been reached press the Set button To reset the value and undo any changes press the Reset button 32 Wiser Home Controller User s Manual 8 6 User System IO Time The widget is used to select a time for controlling some aspect of the C Bus system The details of the usage will depend on the project The name of the controlled item is above the widget start Time A Short Press on the up or down arrows will change the column value by one A Long Press on the up or down arrows will cause the value to change continually until released When the desired value has been reached press the Set button To reset the value and undo any changes press the Reset button 33 Wiser Home Controller User s Manual 9 0 Other Widgets 9 1 Web Camera The Web Camera widget is used for displaying the video from a Web camera Click the Web camera picture to display the image full screen Click the home button the picture of the house in the bottom right corner to return to normal view security Cam Big2. NV l D r ere Nii Wiser Home Control 5200PG B FE CE User s Manual Copyright Clipsal Australia Pty Ltd 2009 All rights reserved This material is copyright under Australian and international laws Except as permitted under the relevant law no part of this work may be reproduced by any process without prior written permission of and acknowledgement to Clipsal Australia Pty Ltd Clipsal and C Bus are registered trademarks of Clipsal Australia Pty Ltd The information in this manual is provided in good faith Clipsal Australia Pty Ltd CAPL has endeavoured to ensure the relevance and accuracy of the information but it assumes no responsibility for any loss incurred as a result of its use CAPL does not warrant that the information is fit for any particular purpose nor does it endorse its use in applications that are critical to the health or life of any human being CAPL reserves the right to update the information at any time without notice Version 0 1 Release date March 2009 Wiser Home Controller User s Manual 1 0 Introduction 5 2 0 Installation 6 2 1 Wiser Home Gateway Components 6 2 2 Status Indicator LEDs 3 0 Concepts 9 4 0 The Wiser Home Controller User Interface 11 4 1 Status Icons 11 4 2 RSS Feeds 12 4 3 Email Notification 13 4 4 Date and Time 13 5 0 Basic Guidelines and Use 14 5 1 Opening the Wiser User Interface 14 5 2 Sequence of Operations 14 5 3 Terminology 15 5 4 Navigat
3. Room Security Can 34 Wiser Home Controller User s Manual This page is blank for formatting purposes 35 CLIPSAL LIVING ELECTRICAL Product of Clipsal Australia Pty Ltd A member of Schneider Electric CIS Technical Support Hotline 1300722 247 Australia Technical Support email cis_support clipsal com au Contact us clipsal com feedback Clipsal Australia Pty Ltd reserves the right to change National Customer Service Enquiries specifications modify designs and discontinue items without incurring obligation and whilst every effort is made Tel 1 300 202 5 2 5 to ensure that descriptions specifications and other information in this document are correct no warranty is Fax 1300 202 556 given in respect thereof and the company shall not be liable for any error therein Clipsal Australia Pty Ltd F2164 March 2009 1036671
4. ce 26 Wiser Home Controller User s Manual e Play Pause Stop e Next Previous e Rewind Fast Forward e Record The name of the controlled device is above the widget A Short Press on an icon will activate that function 7 17 Home Safe Panel The Home Safe Panel widget is used for controlling and monitoring a C Bus security panel There are several areas of the widget e Panel status at the top this shows whether the security panel is connected to the Wiser Home Controller e Keypad this is used in the same way as a regular security panel keypad e Panel status indicators at the bottom these show the status of the panel including any alarms e Zone status at the right these show whether the zones are secure or not Alarm Not Connected Zone 1 Zone2 Zone3 2 3 Arm Zone4 Monitor Alarm Line Fail Tamper Arm Failed Panic Fire Battery Low Gas Mains Fail Other 27 Wiser Home Controller User s Manual 7 18 MinderPro Panel The MinderPro Panel widget is used for controlling and monitoring a MinderPro security panel There are several areas of the widget e Panel status at the top this shows whether the security panel is connected to the Wiser Home Controller e Keypad this is used in the same way as a regular security panel keypad e Panel status indicators at the bottom these show the status of the panel including any alarms Zone status at the rig
5. chunky bits of bacon it s 14 a bar and it s sold out 3 P 6 71 PA ER ASS 12 Wiser Home Controller User s Manual 4 3 Email Notification If an Email account has been selected for use with the Wiser Home Controller you will see the Email icon at the bottom of the screen along with the number of messages waiting to be read If the number of Emails is unknown a question mark will be shown When Email messages are received the number will be shown If you click you will be able to select and Email and see the sender and subject of the Email The full text of Emails is not available for reading on the Wiser Home Controller 4 4 Date and Time The date and time is shown in the bottom left corner of the screen 5 24 PM Tuesday 25 November 2008 If the RSS Feed panel is expanded you will see an analogue clock VEZ fi K nH TANS z t ty hy 2 WS fyriliti To set the date and time go to the Tools page 13 Wiser Home Controller User s Manual 5 0 Basic Guidelines and Use 5 1 Opening the Wiser User Interface You control of the Wiser Home Controller using a Web based user interface usually a web browser This could be a web browser connected to the Local Area Network LAN or connected remotely via the Internet It is also possible to control the Wiser Home Controller via a projector application running on a device like a mobil
6. con Irrigation Schedule A Short Press on the icon will set the item to the preset level 7 11 Two State Enable The Enable Preset widget is generally used for enabling a function of the C Bus system such as a scheduled event The appearance will depend on the icons selected one for the off state and one for the on state The name of the controlled item is underneath the Icon Away From Home 7 12 Fan Controller The Fan Controller widget is used for controlling the speed of a ceiling fan The current speed of the fan is shown above the widget The name of the controlled load is underneath the widget Bedroom A Short Press on the left or right arrows changes the fan speed If the fan is on a short press on the fan will switch it off 24 Wiser Home Controller User s Manual 7 13 Scene Trigger The Scene Controller widget is used for setting a scene This allows many lights to be set to pre determined levels all at once The appearance will depend on the Icon selected The icon will show whether the scene is set or not indicated by the brightness of the icon The name of the scene is underneath the icon r Scene 1 A Short Press on the icon will set the scene 7 14 Local Scene Controller The Scene Controller widget is used for setting a scene This allows many lights to be set to pre determined levels all at once The appearance will depend on the Icon selected The icon will show whether t
7. controlled device can be set Bedroom Curtains Open There are three options e One button control a single button is used to open close and stop e Two button control one button is used to open stop and the other is used to close stop e Three button control one button is used to open one is used to close and the third is to stop Functions of buttons 21 Wiser Home Controller User s Manual Number of Button One Button Two Button Three buttons Open Stop Close Stop 7 6 Shutter Relay The Sutter Relay widget is used to open and close electric curtains blinds and shutters The Shutter Relay widget is very similar to the Curtain Controller widget Refer to the icon shown for the Curtain Control widget The general appearance of the widget is fixed The button labels and the name of the controlled device can be set Function of buttons Number of Button One Button Two Button Three buttons Open Stop Close Stop 7 7 Lighting Preset The Lighting Preset widget is used for setting a load to a preset level from 0 to 100 The appearance will depend on the icon selected The icon will show whether the load is at the preset level indicated by the brightness of the icon The name of the controlled load is underneath the icon A Short Press on the icon will set the load to the preset level 22 Wiser Home Controller User s Manual 7 8 Lighting Status The Lighting Status widget shows when a l
8. e phone or PDA To display the Wiser Home Controller user interface on a web browser that is connected to the LAN enter the following URL in the web browser http 192 168 2 1 or the address as configured during installation Note You will need to use the actual IP Address of the Wiser Home Controller in the above URL When you first open the Wiser Home Controller user interface you are prompted for a user name and password The default values are Username admin Password admin The user name cannot be changed It is recommended that the password be changed for security 5 2 Sequence of Operations Power On and Initialisation Power on the Wiser Home Controller before accessing the Wiser user interface Allow time for the router to establish connection with the C Bus network and to poll the states of the C Bus devices through the C Bus Network Interface CNI This is important to give a true picture of the status of the equipment and to allow scenes to begin from Know start points Try to avoid disconnecting power from the Wiser equipment It is better to let it remained powered on than to remove power on a random basis You can get a good indication of the status of the system from the indicator LEDs on the Wiser router and CNI Most indicators should be green or flashing green during normal operation Some activity between the router and C Bus network is normal at any time even when not being controlled or monitored by you usi
9. eft it shows whether you are connected or not The meaning of the other information is as follows e Attempted reconnects this is the number of times a re connect to the Wiser Home Controller has been attempted This will normally be O for a wired Ethernet connection For a wireless connection this number will increase while the connection is lost e Keepalive signals this is the number of keep alive signals received from the Wiser Home Controller These are sent on a regular basis so that the user interface Knows that the Wiser Home Controller is still connected e Watchdog Counter this is the number of times the user interface has checked to see if a Keep alive signal has been received It gets reset to O each time a Keep alive is received e Successful Connections this is the number of times a connection has been successfully made to the Wiser Home Controller This will normally be 1 for a wired Ethernet connection For a wireless connection this number will increase each time a new connection is made 4 2 RSS Feeds If RSS feeds have been set up for use on your Wiser Home Controller you will see the headlines appear at the bottom of the screen 5 24 PM Tuesday 25 November 2008 Bacon chocolate a hit with the Brits If you click on the up arrow bottom right corner the area for displaying the RSS data will expand and you will see the full text wii Bacon chocolate a hit with the Brits ND S a IT S milk chocolate with
10. f the screen The Connection status icon is the only icon you will see if all is operating gt correctly w This icon reflects the state and of the user interface s web browser connection to the Wiser Home Controller The plug on the icon will be shown in one of three colours e Green all is working correctly e Orange has a connection to the Wiser Home Controller but the data is out of date or has not recently received a keep alive message see below e Red there is no connection to the Wiser Home Controller This can happen for many reasons Typically this happens when using the web browser over WiFi and the WiFi is going out of range The C Bus icon with a red slash across it means that the Wiser Home Controller does not have C Bus connectivity This could be caused by no C bus connection wrong CNI IP Address or no CNI The wrench icon means that the Wiser Home Controller is currently in CNI mode meaning that the device is being used as a CNI and thus the web browser control will not function until the CNI mode is disconnected Once CNI mode is disconnected the icon will disappear and the Wiser Home Controller can be used like normal In case of problems you can click on the icons and you will see some additional status details 11 Wiser Home Controller User s Manual attempted reconnects l C E keepalive signals S watchdog counter successful connections disconnected At the bottom l
11. he skin used and the selected widgets A typical screen is shown below Function Groups Locations Status Icons Volume 48 CD Radio 1 Radio 2 A widget is a graphical component displayed on the Wiser Home Controller that is used to control and or display the state of something Typical functions for widgets include e Controlling lighting e Controlling a home audio system e Controlling and monitoring a security system e Displaying aWeb camera The Wiser Home Controller displays the Widgets using the selected skin The skin defines the appearance of the background and the Widgets as well as the way the user interface operates The Wiser Home Controller automatically arranges the Widgets onto pages according to their Location and or Function Group 9 Wiser Home Controller User s Manual Locations are used to arrange Widgets according to their physical location in a site A project can have between 1 and 20 locations Typical Locations in a Home might include e Lounge e Dining e Bedrooms e Outside Function Groups are used to arrange Widgets according to their usage A project can have no Function Groups or up to 20 Typical Function Groups in a Home might include e Lighting e Security e Climate Control e Media Audio Video 10 Wiser Home Controller User s Manual 4 0 The Wiser Home Controller User Interface 4 1 Status Icons Several icons might be displayed in the top right corner o
12. he scene is set or not indicated by the brightness of the icon The name of the scene is underneath the icon Scene Il A Short Press on the icon will set the scene Clicking the Up and Down arrows will nudge the level of the scene by a small amount This is useful if the lighting level is not quite right and needs to be adjusted brighter or dimmer 25 Wiser Home Controller User s Manual 7 15 Multi Room Audio Zone The MRA Zone Widget is used for controlling a Clipsal Multi Room Audio MRA system The widget allows you to e Select a music source e Adjust the volume e Adjust the bass and treble levels A Long Press on the or buttons will allow the volume to be adjusted up louder or down quieter respectively The mute button the picture of a speaker allows you to switch the sound off and on The source selection buttons at the bottom allow you to select which music source you want to listen to The selected source will be highlighted N Volume Treble CD Player FM Radio Internet Radio Clicking the back button will take you back to the other controls page A Long Press on the or buttons will allow the bass and treble levels to be adjusted Clicking the back button will take you back to the other controls 7 16 Media Transport The Media Transport Widget is used for controlling an audio video system The widget allows you to activate any of the following functions of an audio video devi
13. ht these show whether the zones are secure or not Disarmed J 2 3 Away Alarm Line Fail Tamper Arm Failed Panic Fire Battery Low Gas Mains Fail Other 28 Wiser Home Controller User s Manual 7 19 Climate Control The Climate Control widget allows the user to control and monitor the following aspects of an air conditioning system 1 Switch the air conditioner on and off 2 Monitor the room temperature 3 Set the operating type Heat Cool Heat Cool Fan vent Set the temperature set point Set the fan speed 6 Switch the zone air flow damper on and off Zone1 e PPPT E c EM Fan Speed Auto a oe Cy eee ea 29 Wiser Home Controller User s Manual 8 0 Logic Widgets Logic widgets are used by the Wiser logic engine These are used to provide customised behaviour for the Wiser Home Controller Their usage will be unique for each project 8 1 User System IO Integer The widget is used to select an integer whole number for controlling some aspect of the C Bus system The details of the usage will depend on the project The name of the controlled item is above the Widget h a Reset Set A Short Press on the up or down arrows will change the value by one A Long Press on the up or down arrows will cause the value to change continually until released When the desired value has been reached press the Set button To reset the value and
14. ion 15 5 5 Tools 16 5 5 1 Remote Access 16 5 5 2 Configure Router Settings 17 5 5 3 C Bus Date and Time 17 5 6 Full Screen View 18 6 0 Widgets 19 6 1 Icons 19 7 0 C Bus Widgets 19 7 1 General Lighting Relay 19 7 2 Two State Lighting Relay 20 7 3 General Lighting Dimmer 20 7 4 Bellpress 21 ES Curtain Control 21 7 6 Shutter Relay 22 Til Lighting Preset 22 7 8 Lighting Status 23 7 9 7 10 7 11 7 12 7 13 7 14 7 15 7 16 7 17 7 18 7 19 Wiser Home Controller User s Manual General Lighting Timer Enable Preset Two State Enable Fan Controller Scene Trigger Local Scene Controller Multi Room Audio Zone Media Transport Home Safe Panel MinderPro Panel Climate Control 8 0 Logic Widgets 8 1 8 2 8 3 8 4 8 5 8 6 User System IO Integer User System IO Real User System IO String User System IO Boolean User System IO Date User System IO Time 9 0 Other Widgets 9 1 Web Camera 23 24 24 24 25 25 26 26 27 28 29 30 30 30 31 32 32 33 34 34 Wiser Home Controller User s Manual 1 0 Introduction The Wiser Home Controller allows you to access your C Bus using a graphical user interface sometimes referred to as the Wiser UI The Wiser Home Controller arrives with a sample project loaded and the user interface accessible from you local home network With certain options set you can access the Wiser UI from anywhere using the Internet Using the Wiser Home Controller you can e cont
15. name of the controlled load is underneath the Icon Cellar Light A Short Press on the icon changes the state from on to off or vice versa 7 3 General Lighting Dimmer The General Lighting Dimmer widget is used for level control of a load from 0 to 100 The appearance will depend on the icon selected The icon will show whether the load is on or off indicated by the brightness of the icon The level of the load 0 to 100 is shown above the icon The name of the controlled load is underneath the icon Lounge A Short Press on the icon will change the state from on to off or vice versa A Long Press on the icon will cause the load to dim up or down An arrow next to the widget indicates the direction of the change The dimming change will stop when the mouse button is released 20 Wiser Home Controller User s Manual 7 4 Bellpress The Bellpress widget is used for on off control of a load The appearance will depend on the icon selected The icon will show whether the load is on or off indicated by the brightness of the icon The name of the controlled load is underneath the icon ai Doorbell A pressing clicking the icon will change the state to on Releasing will change the state back to off 7 5 Curtain Control The Curtain Controller widget is used for opening and closing electric curtains blinds and shutters The general appearance of the widget is fixed The button labels and the name of the
16. nd highlighted 5 5 Tools On the Tools page you can select Enable Remote Access Configure Router settings and Set C Bus Date and Time To select the Tools page click on the Tools icon at the bottom of the Function Groups list 5 5 1 Remote Access The Remote Access settings can be set or reset using the Wiser UI To access the screen with the remote access settings buttons go to the Tools page Changing remote access settings will prevent certain access modes from working Be sure you know what the effects of a change will be before you change the current setting Some changes will cause a reboot and could interrupt activity on your CAUTION network Rem Disabled Will Cause Projector Control Disabled System Reboot Disabled Toolkit Control allows the device to be used as a CNI over the Internet This means that anyone on the Internet if they Knew the Internet address of your device can connect on port 10001 and perform C Bus tasks Disabling 16 Wiser Home Controller User s Manual closes this port The port is closed by default This feature is intended to allow installers to use C Bus Toolkit to manage a C Bus network remotely when they need to IT IS IMPORTANT TO MAKE SURE TO CLOSE THE PORT AFTER USE LEAVING IT OPEN ALLOWS ANYONE TO MANIPULATE YOUR C BUS NETWORK Projector Control allows the web user interface to function even when run remotely over the Internet This feature is intended t
17. ng the Wiser UI 14 Wiser Home Controller User s Manual maintenance events such as using Toolkit transferring a project to the Wiser unit using PICED or when the router is rebooting or performing power on self tests Also during Wiser project maintenance other programs running on your home LAN might be interrupted or slowed down i The monitor and control functions might not be available during 5 3 Terminology Short Press The term short press is used to describe clicking the mouse button and then releasing within about 1 2 second If you are using a touch screen device you will be pressing the screen with your finger rather than using a mouse In this document it is assumed you are using a mouse Long Press The term long press is used to describe clicking the mouse button and then holding for more than 1 2 second before releasing 5 4 Navigation Groups of widgets can be selected based on either their Location or their Function Group The Function Groups are displayed down the left side of the screen To change the Function Group Click one of the icons The selected Function Group will be shown highlighted Click the arrow at the top or bottom to see more Function Groups if there are any 15 Wiser Home Controller User s Manual The Locations are displayed across the top of the screen To change the Location Click the name of one of the Locations The selected Location will be shown centred a
18. o allow an end user or installer to interact with their C Bus network even when outside of their home or premise Project Update allows a PICED project to be uploaded to the device over the Internet This means that anyone on the Internet if they Knew the Internet address of your device can connect to the device and transfer a project to the unit and or retrieve a project from the unit It is important to make sure to close the port after usage as leaving it open will allow anyone to manipulate your C Bus network 5 5 2 Configure Router Settings You can access the router to view or change the settings Some of the settings relate to network security and wireless operation and might require you to make a change Changing settings on the router can cause unexpected results N Unless you are absolutely certain do not attempt to modify the settings CAUTION To open the router setup screen display use the Configure Router button on the Tools page Most of the router setting screen fields require text entries After making a change it must be saved Saving changes causes the router to reboot 5 5 3 C Bus Time and Date The C Bus Date and Time widget on the Tools page allows you to set the network time from the Wiser UI 17 Wiser Home Controller User s Manual To increase a value select the up triangle To decrease a value select the down triangle Click the Set button to change the date or time to the new value The defaul
19. oad is on It is not used for controlling the load The status can be shown with an icon or a level from O 100 The appearance will depend on the icon selected The icon will show whether the load is on or not indicated by the brightness of the icon The name of the controlled load is underneath the icon The level of the load will be displayed O 100 The name of the controlled load is underneath the icon Any press on the Widget will be ignored 7 9 General Lighting Timer The General Lighting Timer widget is used for switching on a load for a specific period The appearance will depend on the icon selected The icon will show whether the load is on or off indicated by the brightness of the icon The animated clock will show if the timer is currently running The name of the controlled load is underneath the icon 100 LE Outside A Short Press on the icon will switch on the load and start the timer running A second press will stop the timer and switch off the load If left running the load will switch off at the end of the period 23 Wiser Home Controller User s Manual 7 10 Enable Preset The Enable Preset widget is generally used for enabling a function of the C Bus system such as a scheduled event The appearance will depend on the icon selected The icon will show whether the preset level is selected indicated by the brightness of the icon The name of the controlled item is underneath the i
20. oller router e C Bus Network Interface CNI e Busbar to connect the router and CNI e Power supply for the router and the Ethernet side of the CNI LAN cable e Wiser 1GB USB drive for product information e Setup sheet Wiser Home Controller User s Manual The Wiser Home Controller router connects to the following e Power provided by a plug pack connected to the busbar e Wide Area Network WAN this is the Internet connection usually via the busbar e Connection to CNI this is normally done by the busbar e Other Ethernet Devices these are plugged into the spare Ethernet ports The CNI connects to e Power provided by a plug pack connected to the busbar e C Bus this is the connection to C Bus and is normally a pink cable e Connection to Wiser Home Controller this is normally done by the busbar The certified installer uses Clipsal PICED and C Bus Toolkit software to create a unique project for the customer s home The project is transferred to the Wiser router unit It is then ready to be used with the Wiser User Interface Wiser UI With the appropriate settings the configuration can be modified later and the project loaded as needed The installer provides the homeowner with the IP address and security codes needed to access the project The Wiser UI can be accessed at home or remotely over the Internet 2 2 Status Indicator LEDs The LEDs on the Wiser Home Controller and CNI provide useful informa
21. rol equipment such as IP cameras C Bus devices and non C Bus wired and wireless equipment on the home LAN e schedule events in the home e create and store scenes on board e customise a C Bus system using the onboard Logic Engine e monitor the home environment including C Bus and security systems Note Examples of equipment you might access with Wiser Home Controller include lighting HVAC curtains sprinkler systems and security controls The User s Manual is provided to familiarise you with some of the features of the user interface and to help you to use it more effectively Some of the illustrations in this document might not look exactly like what you see on your screen This is because there are several different skin designs and there are many different devices available for accessing your Wiser Home Controller Wiser Home Controller User s Manual 2 0 Installation 2 1 Wiser Home Gateway Components For details of installation of the Wiser Home Controller refer to the Wiser Home Controller Installation Instructions and the Wiser Home Controller Setup Sheet antennas Wiser Home Controller LAN ports busbar power supply connection from the eo Internet link connected to CNI Remove cover to install C Bus twisted pair wires Optional support stand attaches here C Bus Network Interface CNI The Wiser Home Controller has the following hardware components e Wiser Home Contr
22. t display is DD MM YYYY and the default is a 24 hour clock E Enable Daylight Savings Time You can enable or disable automatic adjustment for Daylight Savings Time Daylight Savings can be set automatically using a schedule Refer to the PICED help file for details Note Make sure the C Bus network is connected when changing the time and date settings 5 6 Full Screen View To have the window fill the screen press or click the full screen icon in the top left corner Press or click the icon again to return to normal 18 Wiser Home Controller User s Manual 6 0 Widgets 6 1 Icons There are many icons available for use with this skin They can be selected for use with Function Groups and for some widgets Some of the icons available are shown below Air conditioner Lights 7 0 C Bus Widgets 7 1 General Lighting Relay The General Lighting Relay widget is used for on off control of a load The appearance will depend on the icon selected The icon will show whether the load is on or off indicated by the brightness of the icon The name of the controlled load is underneath the icon A Short Press on the icon will change the state from on to off or vice versa 19 Wiser Home Controller User s Manual 7 2 Two State Lighting Relay The Two State Lighting Relay widget is used for on off control of a load The appearance will depend on the icons selected one for the off state and one for the on state The
23. tion about the status of the system Wiser Home Controller router The locations and meanings of the various LEDs on the Wiser Home Controller router unit are shown below LAN Internet 4 3 Wiser Home Controller User s Manual LED onthe Wiser Purpose or Meaning vomeconvoner fenememnns Power he Power LED lights when power is applied to the power Uitandstaysit 2s ong power is present o Security orange he Wiser Home Controller does not make use of reefers fis te e onroter doss not make seot ireless Lit when wireless is available Blinks when pre fransmiting or recewing data oes z DIAG red Lit during self test and a few moments thereafter If PASS fie ight Stays on itindicates a problem o LAN Lit when the Ethernet port is connected to a LAN he numbered LEDs indicate which ports are active C Bus Network Interface CNI The meaning of the two CNI LEDs is shown below hen router is working as a router the LED is lit Note The C Bus indicator LED is powered by the C Bus network Inline CNI LAN C Bus Ethernet Indicator Red Non existent or problematic link 0 off Power problem for example no power connection SiMe P C Bus Indicator Statu C range Red flash C Bus good active communication between C Bus and Ethernet Off i 5 Fe mae Wiser Home Controller User s Manual 3 0 Concepts The Wiser Home Controller web interface appearance depends on many factors including t
24. undo any changes press the Reset button 8 2 User System IO Real The widget is used to select a real value number with decimal point for controlling some aspect of the C Bus system The details of the usage will depend on the project The name of the controlled item is above the widget 30 Wiser Home Controller User s Manual aii il setting h i hd Reset Set A Short Press on the up or down arrows will change the column value by one A Long Press on the up or down arrows will cause the value to change continually until released When the desired value has been reached press the Set button To reset the value and undo any changes press the Reset button 8 3 User System IO String The widget is used to display information of some aspect of the C Bus system The details of the usage will depend on the project The name of the item is above the widget system Mode Pressing the Widget will have no effect 31 Wiser Home Controller User s Manual 8 4 User System IO Boolean The widget is used to select a Boolean value ON or OFF for controlling some aspect of the C Bus system The details of the usage will depend on the project The appearance will depend on the icons selected one for the off state and one for the on state The name of the controlled item is underneath the Icon A Short Press on the icon will change the state from on to off or vice versa 8 5 User System
Download Pdf Manuals
Related Search