Home

User Manual - produktinfo.conrad.com

image

Contents

1. s bouquets only DVB S2 Define whether searching shall cover DVB S2 transponders as well Finding and storing the channels Once the options are set press the Green key on the remote control to start the channel search Once a channel search is started a progress bar and list of channels found will be displayed At any time you may stop the search by pressing Exit on the remote control After the channel search is complete press the Green function key on the remote control to save the channel list and exit FACTORY SETTINGS Use this option to reset the receiver to default settings This may be necessary when a large number of settings have accidentally been made incorrectly for example Access to factory defaults is protected by a PIN code 0000 by default Factory Defaults Press the OK key and confirm with the Green function key if you want to reset the unit to the Factory default settings Factory Defaults Note Using this option will delete all data stored in the channel lists and favourite lists After this the Installation Wizard will be open Please refer to the Installation Wizard section of this user manual for further information Preprogrammed Channel Lists Use this option to reset your TV channel lists to the receiver s preprogrammed default program lists SYSTEM UPDATE This option supports three ways to update the software of the digital receiver Over The Antenna
2. Over clocking Set system speed may result in 20 improvement to the system performance Delete Cookies All downloaded cookies will be deleted CHANNEL SEARCH The receiver supports automatic and advanced channel search modes The automatic channel search was described under the chapter of the installation wizard The following section focuses on the advanced channel search which is a customized search mode Advanced channel search The advanced channel search allows you to make a channel search with customized search parameters Satellite Use this option to select which satellite to search Frequency Use this option to set the frequency of the transponder to search Polarity Use this option to set the polarisation of the signal between horizontal vertical right and left circular 67 68 Symbol rate Use this option to set the symbol rate for the signal FEC Use this option to set the FEC Forward Error Correction PIDs Use this option to set the PIDs between automatic and manual If you choose manual you can set the individual Audio and Video PIDs and the PCR Video PID Use this option to manually set the Video PID Audio PID Use this option to manually set the Audio PID PCR PID Use this option to manually set the PCR PID Channels Select All to search for all Free to Air and encrypted channels Select Free to air to search only for Free to air channels Select HD to search channels on HD
3. 2006 95 EC low voltage directive 2011 65 EC RoHS POWER REQUIREMENTS Mains input voltage 230V Mains input frequency 50 60 Hz Power consumption Typ lt 11W Max 30W Deep standby mode less than 1Watt PHYSICAL SPECIFICATION Size W H D 260mm 53mm 225mm Operating temperature 5 C to 35 C Storage temperature 20 C to 60 C CONNECTIVITY 1 x USB2 0 High Speed Host port 1 x 10 100Mbps Ethernet port RJ45 1 x WiFi 802 11 b g Subject to 3rd party license REAR PANEL INTERFACES Front End Input connector Input connector IEC169 2 Socket F connector for Satellite front end Loop Through Output connector IEC169 2 Plug TV SCART connector CVBS RGB output L amp R Audio output Fast Blanking output Slow Blanking output Digital Audio SPDIF 1 Coaxial RCA 1 Optical CINCH RCA Audio L R and CVBS RCA Ethernet 10 100Mbps RJ45 HDMI USB 2 0 host socket Type A Wifi antenna eSATA port FRONT PANEL Standby Channel Up Down keys VFD display 1 Standby LED Indicator 1 IR Sensor 1 Smart card reader ACCESSORIES User manual English German Remote control unit with batteries HD smart card 1 5m HDMI cable 75 Troubleshooting ERROR POSSIBLE CAUSES POSSIBLE SOLUTIONS No power supply Check connection cables Disconnect device from mains power supply eliminate the short circuit in the coaxial cable or con
4. 3 Use the arrow keys to move the mouse cursor over the screen 4 Press the key to click on links or buttons on the web page Note The mouse cursor will disappear from the screen if the mouse is idle for over 10 seconds Press any of the up down left right arrow keys to re display the mouse cursor on the screen Setup This section explains the most important functions to ensure that you can directly watch television with your new digital receiver Please note additional adjustments may be required Note Do not connect the digital receiver to the main power yet Connecting the Antenna and LNB Low Noise Block to the digital satellite receiver input Connect the LNB on the satellite dish antenna directly to the digital receiver using the LNB in connector of the receiver by means of a coaxial cable You may use the loop through connector to connect to a second receiver Connecting the TV set The digital receiver and TV set can be connected by means of a SCART cable not supplied or HDMI cable Optional Simply connect the two ends of the cable you select to use in connecting the receiver to the TV set The SCART connection ensures that audio and video signals are transmitted to the TV set in optimum quality The HDMI connection is recommended for HD TV In case the TV has a HDMI input connector a special all digital interface that provides the highest picture quality connect the product to the TV with tne HDMI cable Conn
5. lt 1W extended start up time appr 25 seconds When in Economic mode only the stand by LED indication will be lit Auto standby mode Set the period of time upon which the receiver will automatically enter the standby mode if no user interaction took place HbbTV mode Disabled HbbTV services applications are disabled Auto start HbbTV services applications are automatically launched Notify HbbTV services applications are notified on screen and the user may choose to launch them most of the time by pressing the red color key of the remote control Auto red HbbTV services applications are launched in a background mode Press the red color key of the remote control to interact with the app TIME DATE Use this menu to set the time and date Automatic Time Update If the Automatic Time Update is set to On the receiver will receive the time and date automatically from the broadcast signal Note Some networks may transmit incorrect time or date Date Use this option to manually set the date Local Time Use this option to manually set the time Time Zone The DVB standard broadcast time and date is for the GMT time zone In order to display the local time correctly you must set the local time zone 65 66 Note If daylight savings is enabled then the receiver is changing automatically the time on the following condition valid for Europe with no time limit summer times begins
6. Digital audio SPDIF optical output Outputs digital audio signals S PDIF for home cinema connection over optical connector 12 On Off switch Powers on off the receiver Note The image shown may differ from the actual product Remote Control FIRST TIME USE Two 3V Lithium CR2032 batteries come pre installed in your remote control When using the remote for the first time pull out the plastic tab from the remote to activate the batteries REPLACING THE BATTERIES With screwdriver remove the battery tray Insert the batteries with the marking facing up into the battery tray Slide the tray back into the remote until it clicks YOUR TWO SIDED REMOTE Your Receiver is supplied with an advanced keyboard remote control that makes internet browsing simple and convenient Standby switches the receiver into standby mode Mute mutes the audio outputs of the receiver Color keys used for selection in On Screen Display menus TV Radio displays the TV Radio channel list Subtitles Audio displays the list of available subtitle or sound track languages 6 Media Access connected media devices Web Access your bookmarks home page or and HD SmartTV web portals 5 Guide displays the TV program guide Info displays detailed program information Fav selects the favorite list the user wants to be active Exit leaves the menu currently on screen 6 7 Up Down Left Right and OK navigation and select keys 12 8 B
7. OTA through the USB port or over the internet When this option is executed the receiver will automatically search for new software version at three sources in the following order a on a USB disk b over the internet and c over the satellite As soon as identifying the first source containing a newer software version the receiver will reboot into a software download mode and will start downloading the new software from the identified source In order to update from a USB disk you need to download the updated software file from our website to the root directory on the USB disk first The USB disk should be plugged in the USB port before executing the System Update option Do not remove the USB disk until the complete software update process is completed In order to update over the internet the receiver must be connected to the internet over a LAN or WiFi connection Remove any USB device from the USB port before you execute the System Update option If the System Update option is executed but there is no USB disk connected and no internet connection the receiver will search for a newer software version over the satellite This procedure may take very long time depending on the size of the new software file and therefore it is recommended to use the USB or internet methods described above for software updates After the new software file was downloaded the receiver will store the new software and automatically restart All user preferences an
8. and ends at 1 00 am universal time Greenwich mean time it begins the last Sunday in March itends the last Sunday in October This is done in disregard of DVB broadcasted information RECORDING Start Stop recording quard intervals Set the start stop guard interval for your scheduled TV recordings USB power during standby mode Set to Off in order to switch off the power of the connected USB drive during standby mode in case there are no scheduled recordings to be performed Note some USB eSATA storage devices may not switch smoothly back on Recording mode When set to On you can switch channel during recording of another channel if both programs are broadcast on the same satellite transponder Note Does not apply to HD recordings LANGUAGES Use this option to set your preferred language for the on screen menus primary and secondary subtitling and soundtracks languages PARENTAL CONTROL Not all TV and radio programmes are suitable for listeners or viewers of all age groups The digital receiver therefore provides an active parental control lock function allowing you to block individual channels by means of a four digit security PIN code Personal Identification Number or restrict content viewing based on restriction rating data if available with the program broadcast The default PIN is 0000 Use the Change PIN option to set a new PIN any time Use the Set Access Rights Level option to control the acc
9. fails of its essential purpose 2 Limitations of Liability Under no circumstances shall the Company or its supplier be liable for a damage to or loss or corruption of programs data or media or b any damages whatsoever including but not limited to direct or indirect damages loss of business profits lost savings or other special incidental exemplary or consequential damages whether for breach of warranty contract strict liability tort arising out of or resulting from the use of or inability to use the products and or the enclosed written materials or the provision of or failure to provide support services even if the Company its supplier an authorized Company representative service provider or dealer have been advised of the possibility of such damages or of any claim by any third party Any liability of the Company or its supplier which is not excluded shall be limited to the purchase price of the Product Some jurisdictions do not allow the limitation of incidental or consequential damages so this limitation may not apply fully to the Customer but such limitation shall apply to the maximum extent permitted by applicable law 3 Application of the Warranty The Company warrants the Product against critical failure resulting from original manufacturing defects in workmanship or material under normal use The company does not warrant any uninterrupted or error free operation of the product or that all deficiencies errors defects
10. for zapping To select a list you can use the TV Radio or Fav keys on the remote control Video photos and music streaming over your home network The Receiver will seamlessly and securely connect to your PC over your home network stream video music and photos from shared folders and allow you to use your PC as a remote storage for recording and playback of your favorite TV programs Hirn eee e a mamii i Accessing shared folders on connected devices i e PCs or Network Attached Storage NAS drives 1 Set login user name and password for the shared folder you wish to access or leave empty if shared folders are not protected 2 Select a connected device on your home network and access shared folders on the device 71 12 Set a shared folder to be your default storage for recorded TV Frequently Asked Questions MOVING CHANNELS AND EDITING YOUR FAVORITE LISTS Under TV Radio entry of the Main Menu select List Manager Select the Favorite list you would like to edit eg My Favorite The next screen will display the Main list on the left side and the Favorite list on the right side Use the Up Down keys to navigate to the channel you want to move from the Main list to the Favorite list Mark the channel by pressing the Green button if you wish to move a block of channels Press OK to move the channel to the Favorite list If you want to re order the channels inside the Favorite list pre
11. keys on the remote control to make a selection d I Soundtrack 59 60 ASPECT RATIO When the info banner is displayed scroll left with the Left arrow key until the Aspect ratio title is displayed Press the Down arrow key and use the arrow keys to set the picture aspect ratio RESOLUTION Resolution allows you to set the video resolution of the picture 1 Press the V Format key 2 The current resolution will be displayed 3 Each time you press the V Format key the resolution changes in the following sequence 576i p gt 720p gt 1080 gt 1080p gt original Alternatively scroll left with the Left arrow key till TV Resolution title is displayed Press the Down key to set the resolution AUDIO FORMAT When the program info banner is displayed scroll left with the Left arrow key until the Audio format banner is displayed Press the Down arrow key and use the arrow keys to select the audio format over the digital audio outputs of the receiver Notes Dolby Digital and Dolby Digital Plus transmissions are down mixed to analogue stereo signals or looped through as is over the digital audio outputs Some Dolby TM broadcasts contain stereo or stereo center audio data and not complete 5 1 audio channels SLEEP TIMER You can use the Sleep timer to specify a time e g at night at which the receiver is to switch to standby mode This is particularly useful if there is no person available at this time to manually swi
12. more when reproduced through a hi fi audio system To do this use a RCA cinch stereo cable to connect the sockets marked Audio L R on the receiver to one of the inputs of your hi fi system marked either Line Aux or Extra If your hi fi system is equipped with a digital audio input you may use a digital RCA cinch cable to connect the electrical Coax digital audio output of your receiver socket SPDIF to your hi fi or Dolby Digital system The receiver is also equipped with an optical digital output If your hi fi system is equipped with an optical audio input you may use an optical cable to connect your hi fi system to your digital receiver Connection to main power supply After all the connections are done you can connect your digital receiver to power Just before plugging a power cable into the wall connector put the power switch on the rear panel in position O off 53 CONNECTION DIAGRAM Home Network Audio amplifier Satellite dish antenna with LNB Video output only VCR DVD Recorder eSATA devices USB devices TV set The Installation Wizard The first time you turn on the receiver a Quick Start Guide menu will be open to assist you with the initial settings This menu will also appear after you do a Factory Reset Use the Green and Red keys on the remote control to navigate forward or back through the wizard steps Press the OK button to edit a para
13. or nonconformities will be corrected Unless the company specifies otherwise this warranty extends only for the original user of the Product and the Warranty applies only in the country or region in which the original user purchases the Product to the Company or a Company Reseller in case of a resale 4 Warranty period The warranty period of the Product is 24 months The warranty period for the Product starts at the day of purchase purchase invoice date of the Customer and in case of a resale by the Company Reseller not more than 45 days after the production date marked on the Product This Limited Warranty extends only to the original end user purchaser of the Product and is not transferable to anyone who obtains ownership of the Product from the original end user purchaser 5 Limited Warranty Exclusions This Warranty with respect to the Customer s Product is subject to the following exclusions i Failure or damage resulting from misuse including but not limited to use of any Product capacity or capability other than that authorized by the Company in writing accident modification unsuitable physical or operating environment or improper maintenance by the Customer ii Failure caused by a Product for which the Company is not responsible iii Any non Company Products including those provided with or installed on a Company Product at the Customer request iv Accessories supply items and consumables e g batteries and
14. the remote control to scroll through valid options for the current channel and program The icons on the right side describe the options see below detailed description for each icon Parental rating information displayed if available with the program broadcast Satellite signal quality bar oN D Program encryption information 9 Teletext information displayed if available with the program broadcast 10 Program timeline information 11 Active recording notification 12 Volume 13 Current time and date 14 Name and schedule of the next program 15 Use the Right arrow key of the remote control to scroll through program information mini TV Guide Full TV Guide and event scheduling Sleep timer Subtitles sD HD Resolution Sa Pre Parental control CEs Audio format Add to favorite T LN T Soundtrack Format ADD TO FAVOURITE Scroll left with the Left arrow button when the Info banner is displayed Add the current channel to one of the available favourite lists SUBTITLES AND SOUNDTRACKS Some TV broadcasters provide several audio channels Soundtracks or subtitles information carrying commentary in various European languages to accompany the TV image Press the Audio Subtitles key on your remote control or scroll left with the Left arrow key when the Info banner is displayed until the Subtitle or Soundtracks titles are displayed with the available subtitling or audio languages Use the directional
15. you may set a reminder for future programs by pressing the OK key on the remote Control Panel In this chapter all options of the Control Panel menu will be described In each of the settings screens use the Right arrow key to view the available options for each parameter on the right side of the screen press OK to effect a selection and the Left arrow key to go back to the parameter list on the left side of the screen USER PREFERENCES This is where you can set the basic parameters of your digital receiver Start up mode Select whether the receiver should display the main menu or switch to the last viewed channel when starting up from standby mode User interface Set user interface parameters such as the duration of displayed menus the transparency level of the menus and the font size used in menu screens History depth You can set the history of previously selected programmes from 1 5 and then use the Back key on the remote control to switch between them Energy mode You can switch the receiver into three different stand by modes Rapid start up If you prefer to get picture and sound immediately after pressing the On button use this option Light stand by Power consumption is reduced while the unit is not in use This mode turns off some parts of the receiver allowing it to start up again quickly when the unit is turned on Economic The receiver will enter into a deep sleep energy saving mode
16. ANDARDS The CE mark which is attached to these products means it conforms to EMC Directive 2004 108 EC Low Voltage Directive 2006 95 EC and RoHS Directive 2011 65 EC WEEE CONSUMER NOTICE The TELESTAR product you have purchased is subject to Directive 2002 96 EC of the European Parliament and the Council of the European Union on waste electrical and electronic equipment WEEE and in jurisdictions adopting that Directive is marked as being put on the market after August 13 2005 and should not be disposed of as unsorted municipal waste Please utilize your local WEEE collection facilities in the disposition of this product and otherwise observe all applicable requirements For further information on how to properly dispose of your product and for information specific to your country please contact your vendor or visit the Support section of our website www telestar de Disposal of Old Electrical and Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropria
17. HbbTV hybrid reception of content from satellite and from the internet HbbTV Hybrid Broadcast and Broadband TV In order to enjoy HbbTV services your receiver must be connected to the internet through wifi or LAN connection Through HbbTV you will be able to access new services from leading broadcasters and online services and application providers including video on demand VoD interactive advertising web applications games and social networking as well as programme related services such as digital text and EPGs The HbbTV services are provided and signalled to the receiver by the broadcasters i e ARD ZDF RTL etc As soon as you tune to channel the receiver will identify the HbbTV service of the channel if available and will launch it through its built in web browser When the HbbTV service is launched some keys of the remote control will have new functionality Follow the instructions on the screen to navigate and operate the service accordingly Pressing the EXIT key of the remote control will leave the HbbTV service and will return to you the full control of the receiver The HbbTV services may be disabled launched automatically or provide on screen notification please see more details on HbbTV settings under the User Preferences section Note HbbTV services rely on your internet connection and therefore performance depends on the speed of your connection Note Like any other internet based services and applicatio
18. PANEL 1 VFD Display 2 Standby indication LED 3 Standby key Switches between operation and standby modes 4 Channel Up key 5 Channel Down key 49 50 REAR PANEL SPDIF AudioR AC 230V 50 60Hz LNB In A E CE 30W Max 950 2150Mhz Electrical shock hazard Do not open 13 18V Elektroschock Gefahr Nicht ffnen Made in Chin Max mA z O V OQ Bu S j SPDIE T eSATA r TV Video AudioL SEE Off On HIGH DEFINITION MULTIMEDIA INTERFACE 10 11 12 N w 7 8 1 LNB In and LNB Out LNB In Connects to the satellite antenna cable LNB Out allows to connect to another digital receiver 2 LAN RJ45 Connection to Local Area Network LAN at home 3 eSATA Connects to a external SATA devices 4 WiFi Antenna Connects to a Wireless LAN home network 5 USB Host Connects to a USB devices 6 HDMI Connects to the TV using HDMI cable for High Definition signals 7 TV SCART Connects to a TV SCART cable This connection supports Standard Definition TV resolutions only 8 Digital audio SPDIF Coaxial output Outputs digital audio signals S PDIF for home cinema connection over coaxial connector 9 CVBS video output Connects to the TV or DVD VCR recorder and outputs analog composite video signals This connection sup ports Standard Definition TV resolutions only 10 AUDIO L R Connects to the TV or DVD VCR recorder and outputs analogue stereo audio signals 11
19. Please consult your installer or card provider for information regarding use of your specific card Channel Lists Editing Use the channel list editor to create edit and organize all of your TV Radio and Favorite channel lists You can access the channel list editor from the Main menu press Menu gt TV gt TV list editor or by scrolling right with the Right arrow key when the infobanner is displayed The Main TV and Main Radio lists contain all of the TV and Radio programmes found during auto and manual search see chapter Channel search In a table you can see the channel numbers and names On the right side there is a small preview screen and at the bottom you can see all available options FAVOURITE LISTS Your receiver allows you to create separate lists of personal favourite programmes This means that each member of the family for instance can create his or her own list of personal favourites sorted according to their individual preferences Use the color keys at the bottom of the screen to manage the favorite lists You can add remove or rename favourite lists as well as edit existing favourite lists Note It is possible to put TV and radio programmes in the same favourite list Set the active list The digital receiver has minimum three lists Main TV Main Radio and My Favorite You can add additional favorite lists as well Once you select one of the lists this list will become the active list that will be used
20. ROGRAM NAVIGATION You can use the numeric keys on your remote control You can use the directional keys Up and Down on your remote control or on the front panel of the receiver You can use the P and P keys on your remote control Select your viewing list by pressing the TV Radio or FAV key select with the navigation key Left or Right the programme list and confirm the selection with OK key VOLUME CONTROL Volume Control allows you to adjust the audio volume 1 Press the Volume key to adjust the audio volume 2 Press the MUTE key to stop the audio temporarily Note The mute function remains set while you switch channels PROGRAM INFORMATION INFO BANNER 14 Notional Geographic z iJ ore of malima i E LETE ma bly ia aml j b 15 SES AN Ai u pe ed pg Program information is always displayed for a certain period of time whenever you switch channels You can view the program information by pressing the Info key while watching a program Press the Exit key to hide the info banner Channel number and name Use the Up and Down arrow keys of the remote control to change channels Current program name and timeline gt e ZE N gt HbbTV web service notification The icon appears when a web based service is available along the broadcast on this channel Press the red color key on the remote control to launch the service on screen 5 Use the Left arrow key of
21. User Manual HD Smart TV Satelliten Receiver 44 HD Smart TV Satellite Receiver User Manual Table of Contents Notices Before using the product Remote Control Setup The Installation Wizard Basic Operation The Main Menu HbbTV Applications Connecting external USB devices Program Guide EPG Control Panel Channel Lists Editing Video photos and music streaming over your home network Frequently Asked Questions Technical Specifications Troubleshooting Warranty service and support 46 49 51 53 54 58 61 62 63 63 64 70 71 71 73 74 76 77 45 46 Notices COPYRIGHT 2013 TELESTAR Digital GmbH Not to be copied used or translated in part or whole without TELESTAR prior consent in writing except approval of ownership of copyright and copyright law Television programs movies video tapes discs and other materials may be copyrighted Unauthorized recording of copyrighted material may be against the copyright laws in your region WARRANTY This warranty does not cover parts which may become defective due to misuse of the information contained in this manual Read this manual carefully and make sure you understand the instructions provided Should you experience a problem with this unit please refer to the trouble shooting section of this user manual Please retain the original packaging should it be necessary at some stage to return the unit CE MARK FOR EUROPEAN HARMONISED ST
22. ack toggles through recently watched channels 9 Volume up down 10 Channel up down WD 13 14 11 Menu brings up the Main Menu on the screen 12 Keypad for numerical and textual input 15 16 13 Record 17 14 Teletext launches the teletext browser 15 V Format selects the picture resolution 16 Full screen Enlarge framed video to full screen 17 Playback navigation keys see details below ba lt lt Fast Rewind Slow motion press to change the speed IK Pause Play Pause during playback or live TV Time shift gt gt gt gt Fast Forward Slow motion press to change the speed lq Jumps backward during playback E Stop gt Jumps forward during playback 51 52 18 19 20 21 22 23 24 25 31 32 33 Unlock keyboard backlit key press indication led ALTGr function key ALT function key Tab forward backward CAPS function key Back Menu Show Main menu Top web browsing bar Forward 22 23 24 25 26 27 OK Delete Escape Zoom In Zoom Out Home page shortcut Navigation color keys Favorites Mouse pointer on off Battery compartment Note Keys in Yellow require use of ALTGr key to operate keys in Blue require the ALT key USING THE MOUSE CURSOR 1 Make sure the keyboard side is unlocked by pressing the unlock key EA 2 Press the DO key and then bed key one after the other to activate deactivate the mouse cursor
23. d channel lists will remain unchanged Caution Be careful not to interrupt the software update process by removing the USB stick disconnecting the internet or turning off the receiver or otherwise interrupting the installation process If the installation is interrupted by accident such as by a power failure the receiver may not boot up properly afterwards SYSTEM INFORMATION This menu displays information related to the software and hardware version ofthe receiver This information may be required if you request service or repair j Heip Atem Syelom information AUDIO VIDEO SETTINGS This is where you can set the basic audio and video parameters of your digital receiver related to connections on rear panel Digital Audio Out Use this option to specify desired audio format on the digital audio outputs SPDIF HDMI Please check that your 69 70 TV supports Dolby Digital and DTS over HDMI HDMI Video output Use this option to specify the video output format on the HDMI connector TV SCART Use this option to specify the video output format on the TV SCART connector HDCP Use this option to set HDCP protocol over the HDMI connection On or Off ANTENNA SETTINGS Antenna settings options were described under the installation wizard chapter SMART CARD If your receiver is equipped with Conditional Access features such as a Cl or CA slot for a smart card additional options may be available in the menu
24. e High and Low LOF frequencies to match the LNB here Band switching The receiver uses a 22kHz signal to control the band of the LNB If you do not know if your LNB supports this feature set the option to Auto Pr Hato Mastage j Pisans select the type of LUD in use i i Antonia Settings DiSEqC type and DiSEqC input You can connect up to two cascadable DiSEqC switches to the receiver This option allows you to set the type and input port for each switch Reference transponder This option allows you to set which transponder is used as the reference for the satellite signal strength 55 56 Transponder number Use this option to select a transponder from the built in transponder list Once selected from the list the Frequency Polarity and Symbol rate fields will be updated accordingly Alternatively you can set these fields manually Heip Mercy TELEP UT JELE i Frequency Set the frequency of the reference transponder Polarity Set the polarity of the reference transponder Symbol rate Set the symbol rate of the reference transponder Tuner IF and Channel ID Unicable only This option allows you to select the Unicable Tuner IF frequency also known as User Band frequency and the channel ID for the receiver In a typical Unicable installation you are able to connect multiple receivers to a single LNB or Multiswitch output with each receiver set to connect to a different Unicab
25. ecting the Network The receiver connects to the internet through the internet router or DSL cable modem in your home The receiver can connect to the router or DSL cable modem via the Ethernet or Wi Fi interface depending on the interfaces supported by your router or DSL cable modem equipment 1 Connecting via the Ethernet port Connect one end of the Ethernet cable to the receiver and the other end to the LAN port at the router or DSL cable modem 2 Connecting via the Wi Fi interface Set the options for the Wi Fi Network Name SSID Select the network name of your Wi Fi access point from the list Security Type WEP WPA WPA2 The receiver supports WEP 40 128bit ASCII WEP 40 128bit HEX WPA and WPA2 The settings of the security type of the Wi Fi and the receiver shall be the same Password When using the security type you must set the password Enter the same password in the Wi Fi setting menu Note To improve quality of service keep the distance between the Wi Fi access point and the receiver close Connection to a DVD recorder or video recorder The DVD recorder or video recorder may be connected to the receiver via a SCART connection or the CVBS video and analogue stereo audio outputs Note The A V output of the DVD recorder or VCR needs to be connected to the TV directly and cannot be connected to the receiver Connection to a hi fi system The audio quality of digital TV and radio programmes can be enjoyed even
26. ess to channels system settings or both a Parental Control Note In case you forget your pin code call customer service NETWORK SETTINGS The receiver can connect to the internet through your home network router or DSL cable modem Connection to the internet allows you to access internetbased content applications and services offered by the broadcasters or over the public internet Use LAN wired if the receiver is connected to your home network over the Ethernet port or WLAN wireless if it connects to a wireless router in your home network Status Check the status of your network connection 7 EET Eee pr paren ZEN d gl dema es EEE EE pesak E Jedi gue ars erde E he LE ee wit Ont ae a a dei er ei bereen berd rz raras ban Derri Network Storage See page 28 on video photo and music streaming via your home network Network player Set the quality of online video accessed through HLS streaming WEB BROWSER Set the parameters associated with browsing web pages and online media using the built in web browser Virtual on screen keyboard Set whether the virtual keyboard should automatically appear on screen when the web page includes an input box Note You can also use the teletext button to show hide the virtual on screen keyboard USB Keyboard Layout Set the layout of the connected USB keyboard Underscan Activate the underscan if web pages are not properly displayed on your TV screen
27. formation for future programmes The mini Guide is accessible through the program info banner 61 62 See detailed description on the Full and mini Guides in the Program Guide chapter Note In order for tne EPG to function properly the time and date must be set correctly MEDIA This entry provides various filters allowing direct access to pre defined media folders Select All to view the list of all media files available on the storage device Select Movies to view a list of all the movie files on your storage device Select Music to view a list of all the music files on your storage device i e mp3 files Select Photos to view a list of all the photo files on your storage device i e jpg or bmp files Select Home videos to view a list of all the home video files on your storage device i e avi files from your video camcoder WEB This entry provides direct access to HD SmartTV portal Note Internet based services and applications are provided by third parties are not under TELESTAR s control and can be terminated at any time without any notice CONTROL PANEL To access Control panel press Menu and scroll down to select Control panel You may select the a settings category using the navigation keys Please see the Control Panel chapter later in this manual for a detailed description of all settings and their options HbbTV Applications Your receiver supports
28. he terms of this Limited Product Warranty The Product is designed to allow access to the HD online video services and applications under the HD SmartTV portal Being an internet based service the HD SmartTV portal may be unavailable at any time without any notice and is completely out of the control of Telestar Digital GmbH The SmartTV portal is operated exclusively by HD and any claim or problem associated with the availability of the service provisioning of the service quality or availability of content content copyrights other IP rights etc should be addressed to HD s service department directly and are not covered in any way by the terms of this Limited Product Warranty 6 Service during the warranty period In the event the Product is found to be defective within the warranty period Customer s sole and exclusive remedy and the entire liability of the Company under this Limited warranty will be at the Company or its Service Center at its option 1 Repair the Product by means of remote support such as but not limited to telephone email support 2 Upon the product return to the party supplying it to the Customer freight an insurance prepaid 2 1 repair or replace any defective Product or parts of the Product thereof covered by the Warranty with new or factory refurbished Products or parts that are equal to new products in performance 2 2 refund the amount paid for the product less a reasonable allowance for usage U
29. ion to the earth ground system of your house building or by a qualified installer 47 48 VENTILATION Do not expose the product to high temperatures such as placing it on top of other product that produce heat or in places exposed to direct sunlight or spot lights The ventilation slots on top of the product must be left uncovered to allow proper airflow into the unit Do not stand the product on soft furnishings or carpets Do not stack electronic equipment on top of the product Do not place the product in a location subject to extreme changes in temperature The temperature gradient should be less than 10 degrees C hour Place the product in a location with adequate ventilation to prevent the build up of heat inside the product The minimum ventilation space around the unit should be 7 cm The ventilation should not be impeded by covering the ventilation openings with items such as newspapers table cloth curtains etc POWER SOURCES The product is not disconnected from the AC power source mains as long as it is connected to the power outlet or wall socket even if the product is turned off ifthe product will not be used for a long period of time disconnect it from the AC power outlet or wall socket Before using the product This chapter provides detailed description of the product and its accessories PACKAGE CONTENT Remote control User manual 2 Batteries HDMI Cable HD Smart card WLAN Antenna FRONT
30. isions are especially susceptible to this ABOUT THIS MANUAL Instructions in this manual describe the operation using the controls on the remote You can also use the corresponding controls on the front panel with the same markings The on screen display illustrations used in this manual may not match the graphics displayed on your television exactly SAFETY CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING TO PREVENT ELECTRIC SHOCK DO NOT REMOVE COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONAL Graphical symbols and supplemental warning markings are located on the back panel of the terminal WARNING TO REDUCE THE RISK OF FIRE OR SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance Product identification and supply rating are provided on the label found on the bottom of the unit and the back panel respectively SAFETY PRECAUTIONS This digital video receiver has been manufactured in accordance with internatio
31. l currently selected indicating the current programme as well as all following programs This allows you to quickly obtain an overview of programs being broadcasted that day and possibly those of the next several days as well depending on the availability of the EPG data from the broadcaster You can use the directional keys Up and Down to select specific channels and the directional keys Right and Left to search forward and backwards in the programme schedule The synopsis of the programs you navigate through is displayed above the grid view Use the Red key on the remote control to toggle between Full Guide grid view and Quick View see below Use the Green key on the remote control to toggle between Full Guide grid view and a Single Channel View see below 63 64 SINGLE CHANNEL VIEW Press the Green function key on your remote control to toggle between the Full Guide grid view and the Single channel view The Single channel view makes it easier to see an overview of programs or an individual channel e g to search for repeats of a movie or to control the timer for a specific channel MINI GUIDE When the program info banner is displayed scroll right with the Right arrow key to the mini Guide banner The program synopsis will be displayed above the banner Press the Down arrow key and navigate with the arrow keys through the programs listed on the mini Guide banner The synopsis of each program is displayed and
32. le user band and channel ID Heip Mercy Herte takrt He natalia m Ihe Bei anorg In poor aatebile rdia Leten Anlenna Seting TET Signal strength and signal quality bars In two level bar meters on the right side of the screen the user can see the strength and quality of the signal coming from the antenna dish to the tuners These two meters can be used while doing a fine tuning of the antenna position The antenna has to be adjusted to have maximum possible signal strength and signal quality CHANNEL SEARCH In order to view video programs you must first do a channel search Select the search scheme you wish the wizard to follow Select Automatic HD to search for channels on HD s bouquets Select Satellite search to search for channels on all transponders for the selected satellite Select Predefined List to restore a predefined channel list associated with the the Country you have selected earlier For some countries a default channel list is shared Finding and storing the channels Once the options are set press the Green key on the remote control to start the channel search Once a channel search is started a progress bar and list of channels found will be displayed At any time you may stop the search by pressing Exit on the remote control After the channel search is complete press the Green function key on the remote control to save the channel list and exit 57 58 Basic Operation P
33. meter and select its value from the drop list that will appear on the right side of the screen TELEN UA ETE i COUNTRY AND MENU LANGUAGE This is where you can set your country and the menu language related parameters of your digital receiver Select the language to be used for all menus Note This does not change the language for information about programs shown in the EPG Press the Green key on the remote control to continue to Antenna settings 54 ANTENNA SETTINGS Satellites To set up the receiver for the type of antenna connected follow the instructions below Select the satellites you wish to receive with the receiver Each of the satellites in the built in satellite list is configured with predefined default parameters You may press the Blue button Advanced settings to edit these values See below details of the Advanced Settings ADVANCED SATELLITE SETTINGS LNB Type Select Universal for most standard LNBs or Unicable if you have a Unicable LNB or Unicable multiswitch Heip Marne Ar kanna Selarggs Satellite Use this option to select the satellite for which you would like to set the position Use the color keys on the remote control as shown at the bottom of the screen to delete or add a satellite from the satellite list and set their individual settings LOF Low and High Band The LOF Local Oscillator Frequency of the LNB is usually printed on the LNB itself or in its documentation You can set th
34. nal safety standards For your own safety you should read the notes on safety precautions carefully and take note of them before operating your new receiver For your own safety please be sure to follow these safety precautions This product is for indoor use in moderate climates only This product contains no user serviceable parts The unit should only be opened or repaired by qualified service personnel The supplied AC power cable must be used to power this product If the power cord becomes damaged it must be replaced Always refer to qualified personnel Check to make sure operating voltage of the product is identical with your local power supply prior to connecting it to the power socket To prevent fire or shock hazard Do not expose the apparatus to dripping or splashing Do not place objects filled with liquids such as vases on the apparatus Install the product so the AC power cable can be unplugged from power socket immediately in the event of a problem The unit should not be placed near sources of open flame No open flame sources such as candles should be placed on the unit Should any solid object or liquid fall into the cabinet unplug the product and have it checked by qualified personnel before operating it any further Proper grounding For protection from lightning and static discharge the antenna connected to this receiver must be connected to earth ground The proper grounding can be achieved by connect
35. nections reconnect and activate device Defective or missing cables Check connecting cables Check the settings to make sure your TV supports the selected format Short circuit in coaxial cable No image no sound no display Wrong video format selected in the OSD settings Check for defective cables or connectors Alternatively reduce the coaxial cable length The displayed time differs from the deria senine Check the settings and current program g correct the time The CI module or CA card is not Re insert the Card and or correctly inserted module Small blocks in the video occasionally no sound occasionally Signal too weak no signal Scrambled programs are not received The CI module or CA card belong to Use a CA module or Card for a different decoding system the specific decoding system Sound OK but no image Device is set to a Radio channel Change to TV mode The batteries are weak Replace the batteries Install the batteries The batteries are installed observing the correct incorrectly polarity as marked in the battery compartment The Remote Control does not work l Aim the Remote Control directly at the front of the receiver The remote control is not pointed directly at the receiver Remove the obstruction from The front of the receiver is blocked mrono ETETE The frequency has changed Start a channel search Previously receivable programs are no longer received Check all cables and There is a
36. nless the Company specifies otherwise a Product or part that is repaired or replaced under this Warranty shall be covered for the remainder of the original warranty period applying to the Product or part All exchanged parts and Products replaced under this Warranty will become the property of the Company 7 To get the Limited Warranty service In the event that a warranty service is required you should contact your specialist dealer or the point of sale Warrantee claims cannot be made directly to the company Telestar Digital GmbH You should therefore keep your sales receipt as proof of purchase The Company recommends the Customer first utilize Support material shipped with the product product diagnostics information contained on the Web and online support on http www telestar de If unsuccessful to obtain service under this warranty the Customer must notify the Company Technical Support or its authorized Service Center representative of the defect before the expiration of the warranty period Customers will provide appropriate assistance to the Telephone Support personnel to resolve issues If the technical support is unsuccessful The Company or its authorized Service representative will instruct the customer on how to receive warranty repair If the Customer does not know of a Company authorized service center for the Company s product it should contact the reseller If the reseller is an authorized service center they will arrange f
37. ns HbbTV services are provided by third parties are not under TELESTAR s control and can be terminated at any time without any notice Connecting external USB amp eSATA devices Your digital receiver is equipped with a USB and eSATA connections at the back panel When you connect a mass storage class device the receiver will automatically initialize the device and will display an indication that the device is connected Notes Supported file systems NTFS Fat16 Fat32 Ext2 Format Device requires entering the PIN code default 0000 Program Guide The following sections provide detailed description of the two types of program guides Full Guide and mini Guide FULL GUIDE GRID VIEW The Guide grid view can be displayed by pressing the Guide key selecting the Guide entry in the Main menu or by scrolling right with the Right arrow key when program info banner is displayed The Guide data is provided by the TV broadcast channels The receiver will display the EPG data that is available for each channel However the receiver can only display what is provided by the broadcast and has no influence on the quality or reliability of the data While you are watching TV the data will be loaded and displayed while you using the Guide Note The message No EPG Information means that the data is not provided by the channel or the data is not yet received The receiver is able to display the programs available on the channe
38. nt Full HD compliant supporting HD SmartTV and HD Replay WiFi and Ethernet connection Media library TV recording and playback over shared folders network and USB storage devices Microsoft PlayReady DRM HbbTV 1 5 HTML5 support HLS smooth streaming and HTTP streaming Nagravision CAS and PRM embedded Number of channels 6000 Number of favourite list 8 EPG up to 7 days based on SI information Free remote control apps for iPhone Android based smartphones Decoding MPEG2 MPEG4 H 264 VC1 WMV WMA HE AAC MKV AVI XViD JPEG Dolby and MP3 Deep standby low power mode SATELLITE FRONT END Modulation DVB S S2 Input connector F connector with Loop through Frequency range 950 2150 MHz Symbol rate range 1 45 MSym s Input level 25 to 65 dBm LNB voltage 13 18V max 400 mA Tone control 22 kHz DiSEqC and Unicable VIDEO DECODING MPEG2 MP HL MP ML MPEG4 AVC high profile level 4 1 Max resolution 1920 x 1080p Supported resolutions 576i over CVBS video and SCART connectors 576i p 720i 720p 1080i 1080p over HDMI interface Standard PAL Aspect ratio 4 3 and 16 9 Automatic adjustment for 16 9 TV sets Letter Box supported AUDIO DECODING Mono Dual channel Stereo Joint Stereo MPEG1 MPEG2 mp3 AC3 Dolby Digital Plus Digital Audio via S PDIF interface Dolby Digital pass through PCM data output REGULATORY COMPLIANCE Compliant to CE 2004 108 EC EMC
39. or repair If the Customer reseller is not a Company authorized Product s service center they will direct the customer to an authorized service center The Company reserves the right to charge for service in exception cases 8 Governing Law The Customer and the Company consent to the application of the laws of the country in which the Customer purchase the Product to the Company or a Reseller approved by the Company in case of a resale to govern interpret and enforce all of the Customer and the Company s rights duties and obligations arising from or relating in any manner to the subject matter of this Statement of Limited Warranty without regard to conflict of law principles these warranties give you specific legal rights and you may also have other rights which vary from state to state or jurisdiction to jurisdiction 9 Jurisdiction All of our rights duties and obligations are subject to the courts of the country in which you purchase the product to the Company or a Company Reseller in case of a resale Notes Notizen 79 80
40. problem with the signal connectors connected to the RECEIVER Warranty service and support This Limited Warranty applies only to the Product sold by TELESTAR Digital GmbH hereby the Company the Customer purchase for his own use and not for resale The term Product in this Limited Warranty does not include any software programs whether pre loaded with the Product installed subsequently or otherwise 1 Disclaimer and exclusion except as specified in this limited warranty the foregoing warranties are given and accepted in lieu of any and all other warranties or conditions express or implied including but not limited to the implied warranties or conditions of merchantability and fitness for a particular purpose to the extent an express or implied warranty cannot be excluded in some states or juridictions the above exclusion may not apply in that event such warranties are limited in duration to the warranty period no warranties apply after that period because some states or jurisdictions do not allow limitations on how long an implied warranty lasts so the above limitation may not apply this limited warranty gives customer specific legal rights and customer may also have other rights which vary from jurisdiction to jurisdiction customer is advised to consult applicable state or country laws for a full determination of your rights This disclaimer and exclusion shall apply even if the express warranty set forth below
41. ss the Right Left keys to switch to from the Favorite list When on the Favorite list use the Up Down keys to navigate to the channel you want to move Mark the channel by pressing the Green button if you wish to move a block of subsequent channels use the Up Down keys to mark more channels and press Green again Use the Up Down keys to mark the new location of the channel you selected and press OK to move it to the new position MOVING CHANNELS IN MAIN LIST Moving channels and re ordering the Main TV or Radio lists can be done in the same way described for editing Favorite lists However since the Main TV or Radio lists are being updated with routine software updates and are also reset back to their default order pursuant to Factory Reset operation it is not recommended to move channels and or re order the Main lists The Favorite lists are the right tool for the users to create order and manage their own channel lists IS FLASH CONTENT SUPPORTED BY THE WEB BROWSER The web browser embedded in your receiver is compatible with HTML5 and CE HTML and its video player supports the standard MPEG2 MPEG4 audio video formats Web content that is provided in Flash format is not supported and may result in an error pop up message suggesting to install a Flash plug in however such plug in installation is not available for the receiver due to the strict security requirements 73 74 Technical Specifications GENERAL INFORMATION Full HD complia
42. structural parts e g frames and covers v Service of Product alterations vi Service of a Product on which the Customer is using capacity or capability other than that authorized by the Company in writing vii Any Product not manufactured by or for the Company or sold to an end user in a country not covered under 77 78 this Warranty viii Loss of any or damage to programs data or storage media The Company may opt to replace the Product submitted for warranty services and thus any data stored on the original Product may become permanently inaccessible This Limited Warranty is voided by removal or alteration of identification labels on the Product or its parts Any technical or other support provided for a Product under warranty such as How to questions and those regarding the product set up and installation is provided WITHOUT WARRANTIES OF ANY KIND The Company is not liable for any transport delivery insurance costs import duties taxes licensing fees and any charges from telephone fax communication as consequence of the failure of the Product Web based content applications and services are provided by 3rd parties and may be limited to certain regions require additional cost and may become unavailable at any time without prior notice The availability provisioning quality or availability of content content copyrights other IP rights etc of web based content applications or services are not covered by t
43. switched to standby mode When in standby mode the standby LED indication will be shown on the front panel The Main Menu Besides the programme that is received from the TV station your digital receiver is able to display different information on your TV screen like Volume bar Menu Pop ups All those things are used as an interface between the receiver and the user also called GUI Graphical User Interface or OSD On Screen Display The actual GUI display generated by your receiver may differ slightly from those shown on the picture as continuous updates of the software may alter the appearance or even the structure of the menus Navigation within the GUI display is effected by the four directional keys and OK key which is used to confirm a selection as well as in some cases by means of the coloured function keys To enter into main menu press Menu on your remote control Being in a menu and pressing Menu key you will completely exit from all the open menu pages Using Exit key you will exit only from the last open menu page TV Select Live TV to watch live TV from the default channel list GUIDE EPG There are two types of Guides Full Guide and mini Guide This entry provides direct access to full TV and Radio listing Full Guide of a specific day within the coming week The EPG Electronic Program Guide gives you information about current broadcasted programmes as well as the schedule and in
44. tch the receiver to the standby mode Scroll left with the Left arrow key until the Sleep Timer title s displayed and set the time for automatic switch into standby mode d D Sleep Timer Note When switching to standby mode the receiver is also able to switch off some TV sets with Slow Blanking on the SCART connector TELETEXT If teletext information is available on the current channel the symbol will be shown in the channel information banner You can press the on the remote control to display this information You can use the numeric keys 0 9 on the remote control to enter a three digit page number wey VV ij I Fl KOR 1090 ZL ZL EAZL ZEA ARDTest Trauer um Abzturzopf er in Polen Karstadt zoll ein onzer bleiben ote bei Zugqumgl ck im S dtirol Eohlefrachter vom Fiff geweszchleppt EE A arhoff Lob im Fall KAT GT Herths Protertbrief an DFB GL Oke Lg f r deutsche Handbal lar r0 ANKER SOs TANG NNN gazzchmu UT mt Lid Var dn OSO GZ im 20 15 Leben unter Grizzlys CHE Gl ekwunzech ARD 226 FRET Die T STANDBY MODE You can put the receiver in standby mode to reduce the power consumption while the unit is not in use The standby mode turns off some parts of the receiver but does not fully turn off the receiver allowing it to start up again very quickly when the unit is turned on If Economic is set see User Preferences section the receiver will enter a deep sleep energy saving mode when
45. te waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local Civic Office your household waste disposal service or the shop where you purchased the product FOR USED BATTERIES Disposed of the used batteries properly Please follow the local regulations for the battery disposal OPEN SOURCE SOFTWARE NOTICE The product uses certain open source operating system software distributed pursuant to GNU GENERAL PUBLIC LICENSE version 2 and GNU LESSER GENERAL LICENSE version 2 1 each as defined and published by the free software foundation inc the following gpl and Igpl software source codes used in this product can be provided GPL software LGPL software linux kernel wedison cairo busybox ffmpeg zi libgcc libstdc WEB and Internet based Applications Web content and Internet based services and applications are provided by third parties and can be terminated at any time without any notice TRADEMARKS Manufactured under license from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby Laboratories CAUTION PREVENTION OF SCREEN BURN IN Continuous display of still images and graphics such as on screen displays stock market tickers and other fixed non moving patterns can cause permanent damage to the television Plasma screen displays projection televisions and CRT telev

Download Pdf Manuals

image

Related Search

Related Contents

ENSURA DR MRI™ SURESCAN™ EN1DR01, ENSURA SR MRI  Codumé Nanakia 450  Manual técnico do Middleware Cartão de Cidadão  Manual del usuario  フロン類回収業登録申請書添付書類一覧表  CAMCOLVC17  Bradford-White Corp DH1504T* User's Manual  

Copyright © All rights reserved.
Failed to retrieve file