CO2 Fractional Laser System User`s Manual Read this manual
Contents
1. Then you will hear the sound of fans Touching the screen you will enter the next operation mode After few second you will see the screen as below Figure 2 Figure 2 Then you can choose scan mode or impulse mode according to your treatment If you see the screen as below Figure 3 Scan mode Depress footswitch to activate READY STANBY Repeat Delay Micro Pulse Energy Treatment Level Passes e l all 0 30 Coverage EJ 20 m Rectangular 20m m earme maeno sere spenne Figure 3 There is a red warning sentence on the left top of the screen in the meanwhile you will hear sound of warning du du du That is to say the machine is not ready to use You can check the back door of the machine to make sure whether it locked or not If it is not locked we can t use the machine We can close and lock it again 4 2 Steps for operation 4 2 1 Scanning mode When we enter into the scan mode we will see the screen as below Figure 4 Figure 4 e Micro Pulse Energy It refers to the energy of one single point of laser and should be adjusted by the doctors The minimum energy is 5mj the maximum one is 50mj To prevent dangerous consequence caused by mis operation every time the machine is turned on the energy would be back to the minimum one regardless of the set energy in operation e Treatment Level It is the density of laser point It refers to the ratio relationship between the2. actual lighted skin area and the original set area The minimum one is 0 30 the maximum one is 25 0 e Passes It refers to the repeated times to finish the whole scan chose by operator 10 steps are adjustable the minimum one is 1 time the maximum one is 10 times e Repeat Delay It refers to the interval time between each scanning When the Passes number is over 1 it can be adjust The minimum one is 0 1s the maximum one is 5 0s 0 5s adjustable per step e Treatment Area It refers to the shape of laser light area Two scan modes are available Rectangular one and Ellipse one Operator could randomly adjust the width and length The minimum one is 0 1 0 1mm The maximum one is 20 20mm e Handpiece Velocity It refers to the velocity of scan working head scanned area per second The minimum one is 0 1cm2 s the maximum one is 9cm2 s e Estimated Power It refers to energy value of the laser total output automatically calculated by the system itself according to the relative parameters setting by operator the unit is KJ J and mJ Ellipes estimated power 31mJ 1000J Rectangular estimated power 24mJ 981J Attention the expected power is in theory it would be little over or beyond the actual power if improper power seted The doctor will choose the right parameters according to the treatment After the doctor choose the right parameters press ready The machine is ready to use We will hear sound of du du du
3. sun tanned look At this point makeup can be applied 03 1 2 3 4 5 6 7 You will experience a burning sensation on the skin that will last between 30 minutes and up to 3 4 hours following your treatment on the first day If you have discomfort following the treatment take Tylenol or speak with your doctor about a prescribed pain killer such as Vicodin Take with food You may want to take a few days off of work Treatment to the facial area will result in an appearance similar to a darker tan sunburn for the first day A fine scab will be formed by the skin do not be concerned this promotes the healing process After 1 2 days the scar necrotic skin will disappear and the skin will have a tanned look At this point makeup may be applied Redness may persist for up to 3 days On the 4th day or so your face will get darker and then near the 5th to 6th day peeling will occur More intense treatments can take up to 7 days for recovery Wash using a mild soap like Purpose Neutrogena or a soap free cleanser like Cetaphil Wash the treated areas everyday and apply Aquaphor Ointment to the treated sites and lips 4 times a day or more frequently if tightness is noticed Avoid Hot water Eye Area Treatment to the upper Eye lids may results in swelling and create a slight squint Redness may persist up to 3 days Clean your eyes with cool water and dab or pat very lightly with a soft towel Avoid Hot water Lubric
4. while pressing ready The machine make sound of du du du refers to ready to use Whenever you change the parameters and make it ready the machine will make the sound of du du du 4 2 2 Impulse mode When you choose impulse mode you will see the following screen Figure 5 Impulse mode Depress footswitch to activate READY STANBY Power Interval Time Impluse Mode CW Pulse Ultra Impulse mode System Info Figure 4 In this impulse operation mode we can choose three kinds of working mode e CW Continuous mode In the CW Mode the laser would be lighted on skin continually without stop when operator presses the foot switch The adjustable parameter is the output power from 1 to 30w e Pulse pulse mode In the Pulse Mode the laser would be lighted on skin as pulse form The adjustable parameter is output power from 1 to 30w and interval time from 0 to 999ms e Ultra super pulse mode In the Ultra Mode the laser would be lighted to skin as Ultra Pulse form The super Pulse Frequency is 1000Hz the adjustable parameter is output power from 1 to 30w The doctor will choose the right parameters according to the treatment After the doctor choose the right parameters press ready The machine is ready to use We will hear sound of du du du while pressing ready The machine make sound of du du du refers to ready to use Whenever you change the parameters and make it ready the machine will m
5. CO2 Fractional Laser System User s Manual Read this manual carefully before using Attention We seriously announce that for others and your safety Read this manual before using People can repair or check the machine after 5 min of the machine turn off It is forbidden to disassemble the machine while it is working People must stand on the nonconductor place while check repair and fix up the machine All operators must receive training in application technique and security knowledge about CO2 laser The operators must pay great attention to the potential danger of beams of CO2 laser light Only the maintainers of or authorized by our company can repair and maintain the rejuvenator Don t face the laser output beam to eyes or other healthy skins directly in any case Avoid aiming the laser beam at smooth reflection surface such as stainless steel mirror surface etc in order not to hurt eyes or skins by the reflection of laser beam If the unit is cleaned by alcohol the laser irradiation only can be used after the alcohol becomes dry The laser beam should avoid irradiating inflammable and explosive cargo In order to make the viewing fields of the operated part clear and avoid focusing lens of the bit being polluted smoke extracting facility should be equipped when operating Suggest the operators and patients wear laser eye shield with corresponding wavelength when operating High voltage power exi
6. aR R iA 19 4 2 1 Scanning MOG Sey eae js cees ised icessscedauba legis news cansloepn eit cehsiae lie beeiediews 19 4 2 2 IIMPUISE MOCE cece cece ceeeceeeceeeceeeceeeeeeeceeeeeeeeeeeseeteeeteeeenenenens 21 SECTION 5 MALFUNCTION EXCLUDING AND DAILY MAINTAINING 5 1 Maintenance of iNStrUMeNt ccccecceeseeneceeeeeeeceeeceeeaeeeeeeeeeseesneeeees 23 5 2 Guide for Malfunction examination and repai cccecceeeeeeneees 23 5 2 1 The checking of CO2 tube periodically cccceeeceeeeeeeeeeteteeeeeeees 23 DZ Replacing TUSE riia bee elevate E a aa 23 5 2 3 Warning sound checking cceceeeeeeeeeee eter eter eee eaaeaeeeeeeeeeseeaeeeeneees 24 SECTION 6 SHIPMENT CONDITION inccsessceviss na na naa e Aa i 25 SECTION 7 PAKING LIST aie eA OO A ee ene 25 SECTION 8 CO2 FRACTIONAL LASER TREATMENT 0 csseeseeeees 26 1 INTRODUCTION 1 1 Range of application Fractional resurfacing is a new laser treatment modality that creates numerous microscopic thermal injury zones of controlled width depth and density that are surrounded by a reservoir of spared epidermal and dermal tissue the normal skin been left between the injury point allowing for rapid repair of laser induced thermal injury This unique modality if implemented with high repetition Ultra Pulse Laser systems enables high energy treatments while minimizing risks it is less pain less down time and good effect Rhytides Wrink
7. ake the sound of du du du 5 MALFUNCTION EXCLUDING AND DAILY MAINTAINING 5 1 Maintenance of instrument A The machine will be kept by professional trained personnel The keeper must make sure that the machine should be in good condition and clear we can use non corrosive detergent to clean the shell of the machine A Avoiding the mechanical damage and the damage of CO2 tube when we remove the machine A We must keep the 7 joint torsion spring articulated arm with scanner and foot switch in the safe place orderly and cover with dustproof cover after the treatment A The keeper must check the machine after treatment He must confirm the machines is in good condition and then he can keep the machine He will keep the keys of the machine separated with the machine 5 2 1 The checking of CO2 tube periodically The periodical time once a year The checking must be made by a qualified person 5 2 2 Replacing fuse Using screwdriver to unscrew the fuse Putting new fuse into the plug Then screwing it tightly 5 2 3 Warning sound checking When we set up the machine we may hear a warning sound du du du There must be a problem with the machine If the back door of the machine is closed well Please open the back door of the machine and press the back door switch to let it to be at the door closed condition And we will see there are three lights are lighting There are two green lights and one red light If the lights are fla
8. ating the eye with drops i e artificial tears will help to decrease the dryness of your eyes 8 Ifthe skin around the mouth is tight Minimize Facial Expressions remember to lubricate with Aquaphor Ointment as needed and use a straw to drink 9 Rest Avoid strenuous exercise bending straining stooping or lifting heavy objects for 1 week after procedure These activities may cause more swelling and pain on your face and slow down your recovery See other side 10 Sleep in a slightly elevated position Using 2 3 pillows under your head amp neck or sleep a few nights in a reclining chair 11 Avoid sun exposure for at least six months A sunscreen SPF 15 or higher should be applied every day Use a hat and sunglasses Yourskin is extremely vulnerable to the sun after having a laser treatment Protecting your skin and limiting sun exposure ensures the best cosmetic results 12 Please schedule a follow up appointment for 2 3 days after the procedure with your doctor or the esthetician You may not need to come in but at least it will be set if you should want to be seen Attention Treatment with the Fractional CO2 laser takes anywhere from 30 minutes to 1 5 hours depending on the area s that are treated If a repeat treatment is required this is usually performed at least 1 to 2 months later Section 3 What To Expect After Treatment e1 Fractional Laser Treatment produces side effects The intensity and duration of your sid
9. ding Arm Smoke Exhausting System Built in air blow Cooling System Built in circulating water cooling Environmental temperature 5 40 C Relative Humidity lt 80 Power Supply AC 220V 22V 50Hz 1Hz Dimension 430mmx350mmx 1050mm Weight 40kg Working mode Continuos power 1 30W step adjustable each 1 W Pulse power 1 30W step adjustable each 1 Interval time 1 999ms Ultra pulse power 1 30W step adjustable each 1 modulated frequency of 1000 Hz Scanning mode scanning mode Ellipse Rectangular Triangular Repeat Delay 0 1s 5 0s Micro Pulse Energy 5mJ 100mJ Treatment Level 0 30 25 0 Passes 1 10 times Estimated Power 125mJ 1000J Ellipes estimated power 31mJ 1000J Rectangular estimated power 24mJ 981J Treatment area 0 1 0 1mm 20 20mm 0 1 0 1mm 15 15mm Handpiece Velocity 0 1 9cm2 s Treatment Deepth lt 2 0mm 2 EQUIPMENTS AND ACCESORY LIST 2 1 List of all the parts 50 Scanner 2 2 Name of each part and elucidation 2 2 1 The main machine CO2 Fractional Laser Machine PZ 605 Professional Scanners two scanner optional i Focus Length S0mm Focus Length 100mm Glasses Foot Switch 3 THE PROCESS OF INSTALLING 3 1 Preparation for Using When opening up the packing case first you should examine the outer shell of the unit and be sure there is no obvious collision damage You should also make sure that there is no dropout between
10. e as above Adjusting till the focusing flare of the green semiconductor laser coincides with that of CO2 Laser Select lower power after switching on Inspect the output condition of the laser by a piece of pergamyn at the flat surface of the output end of the laser guiding arm If there are double points and double lines CO2 Laser device or semiconductor laser device should be adjusted accurately and carefully following the above mentioned methods Use focusing probe to do cutting operation in general When conducting burning cure in large area take off the focusing probe and put on the focus out probe in order to control the size of the flare 3 2 Attention Don t face the laser output beam to eyes or other healthy skins directly in any case Avoid aiming the laser beam at smooth reflection surface such as stainless steel mirror surface etc in order not to hurt eyes or skins by the reflection of laser beam If the unit is cleaned by alcohol the laser irradiation only can be used after the alcohol becomes dry The laser beam should avoid irradiating inflammable and explosive cargo In order to make the viewing fields of the operated part clear and avoid focusing lens of the bit being polluted smoke extracting facility should be equipped when operating Suggest the operators wear laser eye shield with corresponding wavelength when 1 2 3 operating High voltage power exists inside the apparatus so that unspecia
11. e effects depends on the treatment aggressiveness your individual healing characteristics e2 Generally patients who are treated more aggressively experience more intense side effects that last longer However some patients have greater than expected reactions to less aggressive treatments and others have fewer side effects to aggressive treatments than would ordinarily be expected e3 Notify your physician if the severity of your side effects becomes a problem for you e4 Swelling You will notice most the swelling on the first morning after treatment particularly under the eyes Swelling usually lasts two to three days To minimize swelling do the following Apply cold compresses to the treatment area for 10 minutes of every hour on the day of treatment until you go to bed Sleep elevated the first night Use as many pillows as you can tolerate e5 Redness Most redness resolves during the first week after treatment but a rosy glow can remain for several weeks If you wish you can apply makeup immediately after treatment to minimize the redness e6 Dry Skin Your skin may feel dry peel or flake You may notice a sandpaper texture a few days after treatment This is the treated tissue working its way out of your body as new fresh skin is regenerated e7 Bronzing Crusting and Small Dark Dots Fractional Laser Treatment causes destruction to microscopic cylinders of the skin which then exfoliates during th
12. e healing process In individuals with heavily pigmented skin or in areas where sun damage has produced pigmented lesions these microscopic wounds known as MENDs contain large amounts of melanin Because there are so many MENDs they can make the skin look bronzed or smaller areas appear crusted do not try to scratch them off When high energies are used to produce deep and wide lesions the MENDs can sometimes be seen as individual dark dots On the face the MENDs will shed within 7 10 days Off the face it may take as long as 3 weeks for the MENDs to shed e8 Raw Skin If you develop areas of raw skin post treatment keep them moist with something like Aquaphor or Bacitracin You do not need to apply band aids but keep the areas moist and do not pick at them They will heal very rapidly on their own and without any problems e9 Expected downtime Face up to 3 days Neck up to 5 days Chest and Hands up to 6 days Superficial wrinkles and skin defects usually disappear after one session e10 Deeper wrinkles and acne scars may require more than 3 up to 5 times spaced one to two month apart CO2 Fractional laser treatment clinic data Scanner Micro pulse Interval Treatment Scanning Passes Treatment Kind remarks treatment energy time level mode Repeat times process Repeat 3 or 4 1 2 processes for small In 2 and following treatment Wrinkle 12 5mj ims 1 56 Rectangular times until ski
13. hroughout the operation A local anaesthetic will be injected subcutaneously under the skin with a very fine needle You will feel a slight sting and a light burning sensation but that will disappear almost immediately The anaesthetic will last about 2 3 hours and will guarantee you have a painless procedure e10 At the end of the operation your face will be cleaned with a sterile solution a dressing will then be applied as well as a facial band that will sit under chin and around the head Section 2 Operation Procedure e1 Clean the skin e2 About 20 30 minutes prior to treatment apply a topical anesthetic to the treatment area e3 Right before treatment beginning wash off the anesthetic and apply a thin layer of the tracking gel e4 During treatment apply cold air for patient comfort e5 After treatment use our semi conductor laser physiotherapy laser to enhance the patient s treatment experience and accelerate the benefits of Fraxel treatment Section 3 Note in the Operation Procedure e1 Topical anaesthesia is not required for most patients This should be discussed with patient prior to treatment Avoid premenstrual days e2 Wash thoroughly and let the skin dry before treatment e3 Cover the patient s eyes with non reflecting protective goggles or water soaked gauze e4 Treatment is safe for the face neck chest and hands e5 Initial settings are generally not high enough The patient will not experience an
14. id using metal apparatus which can reflect light as possible as you can for fear of reflecting laser light Even when using ensure not to directly expose laser light on the metal apparatus A During operation operators shouldn t wear watch necklace bracelet or other light reflecting articles A Effective protection measurements must be offered to customers eyes such as gauze eye shield and tarsi A Don t use laser light to irradiate other places other than affected part and target skin when hand tool is moved or after use the front edge of it must be put toward the safe place A There should be a warning sign hanged over the entrance to laser Light Room None is allowed to enter or exit the Room during operation Il Eyes Protection A All operators working within the irradiation space of laser light must wear protective glasses A Careful and effective eyes protection must be offered to customers A Protective glasses cannot absolutely absorb all laser light or reflected laser light by glasses reflection mirror or smooth metal surface For this reason please don t directly see the upper laser light with protective glasses A Gauze eye shield and tarsi are all effective to protect customers eyes Ill Safety of operation room A The operation room must be equiped with smoke exhaust and dust exhaust equipment And labeling caution on the equipment which saying the discharging from the laser machine may contains particulates
15. ime heavier injury more recovery time Longer interval time lighter injury less recovery time 2 For tiny pain it s better have some Anesthetics on the treatment skin After 20 to 30 minutes the treat could begin 3 Bigger treatment level bigger treatment area larger total output energy 4 the scan area should cover the whole treated skin 5 More than 1 month rest time needed between two procedures 6 The whole procedure a Disinfection b Anesthetics c begin treatment d have burn medicine on treatment area
16. les Mottled dyspigmentation Cosmetic Telangiectasia Red Spots Application Solar lentignes Brown spots Large pores Rough skin texture Actinic keratosis Ssun damaged skin precancerous lesions Medical Seborrheic keratosis sun damaged skin applications precancerous lesions Sebaceous hyperplasia yellow shiny bumps on the face Rhinophyma nose swelling and tissue over growth Epidermal Melasma Brown spots 1 2 Range of Contraindication Those who are sensitive to light severe cardiopathy or high blood pressure People who have done skin chemical or laser operation in the last half a year must not use the product Pregnancy woman People took drugs that cause photo sensitisation recently People who have sever keloid scar and systemic lupus erythematosus People with skin pigmentary conditions People with hepatitis tuberculosis and AIDS is forbidden to use it People with blood disease is forbidden to use it People suffering from hight fever is forbidden to use it People with psychopathy is forbidden to use it 1 3 Specifications Laser Type 10 6um Output Power 220W Starting Voltage lt 25kV Operating Voltage lt 15kV Operating Current lt 25mA Focal length of working head f 100mm f 50mm Indication Beam Green Semiconductor Laser 532nm 5mW Transmission System 7 Articulation Joint Spring Balanced Light Gui
17. lized technician is not allowed to open up the cabinet in order to avoid electric shock danger If extraordinary noise and smell is found when the apparatus is working the apparatus must be stopped for inspection immediately Power should be cut off before inspection The apparatus assembles glass laser tube inside So pay attentions not to fall down when transport it 3 3 Installation Make sure whether the power voltage coincides with the voltage needed by the unit Screw into earth plug Insert the plug of the foot switch connecting line into the socket on the back of the unit Push the notch till the connection is reliable 4 Insert remote interlock 5 Insert the two ends of the power line into the power input socket and power socket separately The power socket must have a good earth connect the earth nail on the under bed of the outer shell with ground firmly 6 Insert the key into the switch hole of the control board and turn the key 90 degree in the direction of right hand and in the meantime the power is on and the circulating water pump and the cooling fan inside the unit are turned on 7 Turn off the power after several minutes test run OPERATION INSTRUCTION 4 1 The operation of the screen Turn the key of POWER SWITCH in the direction of right hand the computer automatically inspects the unit simultaneously If it works regularly the Figure 1 will be shown CO2 Fractional Laser System
18. n wrinkles The data setting could be smaller if still removal 15mj 2ms 6 25 Big line white 4 5 processes for deep in heavy disease the data could be a wrinkles littler larger Repeat 3 or 4 2 3 In 2 and following treatment Scar 7 5mj 1ms 1 56 Ellipse times until skin processes for light scar The data setting could be smaller if still Removal 15mj 2ms 6 25 0 2 0 2mm white 4 5 processes for heavy in heavy disease the data could be a 0 5 0 5mm scar littler larger Repeat 3 or 4 2 3 processes for light In 2 and following treatment Vascular 12 5mj 1 2ms 1 56 rectangular times until skin vascular The data setting could be smaller if still removal 15mj 2 89 white 4 5 processes for heavy in heavy disease the data could be a vascular littler larger Repeat 3 or 4 2 3 processes for light In 2 and following treatment Large 7 5mj 1 2ms 1 56 Ellipse times until skin condition The data setting could be smaller if still pores 12 5mj 6 25 white 4 5 processes for heavy in heavy disease the data could be a 15mj condition littler larger Repeat 3 or 4 2 3 processes for light In 2 and following treatment Mole 15mj or more 1 2ms 25 Ellipse times until skin condition The data setting could be smaller if still removal white and little 4 5 processes for heavy in heavy disease the data could be a blood out condition littler larger General rule 1 Short interval t
19. of biologic tissue A The operation room must be avoid the existence of the following matter incendive anaesthetic oxidizing gas such as N20 and O2 Content SECTION 1 INTRODUCTION 1 1Range of ADpIICALLON isin siienicaarteenictaotegecata taut ia cadememameaianith 6 1 2 Range of Contraindication ccccccceceeceeeeeeeeeeeeeeeeeeaeeeeeseneaeeeenneees 7 3 DOCHICALONS aits c0 tacvenecaveadle arsadyssecveeeas aadoucantetaantoradutestameda iee 7 SECTION 2 EQUIPMENTS AND ACCESORY LIST 2 1 List of all the Pats sai sci scevedvavescncntacteushasaceineddaadnase dabcostesnaduesdevedenens bane 8 2 2 elucidation each Part ee ceceece cece eee eees teer eeee cece eeeeeeeeeeeeeeeeeeeeeneeanaeanes 9 2 2 1 THE man machine errira a ae Ha a EEA EEA deter ane 9 2 22 TNE SCANNET nenia a a e a a A Eana E Ei 10 2 2 3 The view of whole MACHING cccccccccecececeeeaececseceseeeceeeseeeseeeeeees 11 SECTION 3 THE PROCESS OF INSTALLING 3 1 Pr paration for USING renis riiet a oiea iiaa Ra 12 3 1 1 Laser Guiding Animnncisisicccecetaetevctivesseetia ithe etree a nern enresenn teene 12 3 1 2 CO2 Laser Output Beam core adjustment cceeeeeeeeeereeeeeeeees 13 DZ Aten ON en o arro eda eea A EA Ee A Eoaea keat 14 3 3 Installations aea a a a A AE idee 15 SECTION 4 OPERATION INSTRUCTION 4 1 The operation of the SCFECN cccccccccssssscceceeeceeeceeeeeeceeeeeesessneneaeees 17 4 2 STEPS TOF opera tioN sinen innein a
20. of vitamin E preparations eating large amounts of garlic and consuming alcohol can also produce the same result and should be avoided If pain medication is necessary we recommend you take ibuprofen paracetamol e3 It is better the Client quit smoking at least two weeks before and until 2 weeks after surgery It is well Known that smoking causes narrowing of the blood vessels which leads to a decreased blood supply to the skin thus slowing and interfering with the healing process e4 Be sure to inform your surgeon of any medications you take as well as possible allergies including drug latex plasters and so on e5 The surgeon will decide whether preliminary examinations are necessary such as blood tests an electrocardiogram or x rays of the lungs If this is the case these tests should be performed several weeks before the surgery e6 It is best not to wear any makeup when the client comes in for the operation Wear loose clothing that doesn t need to be pulled over head the client may also want to bring a scarf to cover the bandages on the way home e7 Do not eat or drink anything for 6 hours before your operation e8 Make certain you have someone to collect you and stay with you overnight after the surgery You are not allowed to drive a car for 48 hours after the surgery due to the effects of the anaesthetic e9 On the day of the operation the surgeon will explain each step of the procedure and the nurse will assist you t
21. shing it must be a problem with the corresponding integrate circuit board So the machine makes warning sound If the problem is caused by the integrate circuit board we can disassemble it and fix a new one If the threes lights work in good condition and back door locked well but the machine is still making warning sound you can contact us immediately 6 SHIPMENT CONDITION Temperature of environment 40 C 70 C Relative humidity 10 100 Pressure 500 100hPa The machine must be placed in the warehouse without the pollution of alkaline acid and irradiation by intense light It is forbidden to roll and throw the machine Avoiding vibrating during the shipment 7 PACKING LIST No Name Quantity Unit Note 1 Cabinet 1 set 2 7 Articulation Joint Spring Light Guiding Arm 1 set 3 scanner 2 set 4 Focus Incision handpiece 2 set 5 Power Wire 1 piece 6 Foot Switch 1 piece 7 Key for Power Supply 2 piece 8 Fuse 2A 4 piece 9 Asbest 1 piece 9 User s Manual 1 set 10 Guarantee Card 1 set 8 CO2 FRACTIONAL LASER TREATMENT Section 1 Before the treatment e 1 Two weeks before the surgery the client should not take any medications containing aspirin acetyl salicylic acid since these products affect the bloods clotting mechanism and therefore may lead to excessive bleeding during and after surgery hence resulting increased bruising e2 Taking high doses
22. structural parts and connecting lines and all the equipped spare parts are complete 3 1 1 Laser Guiding Arm CO2 laser guiding arm is composed of debugging tube laser guiding arm scanner the light conducting arm plug and scanner plug The light conducting arm plug and scanner plug are on the bottom of the machine As we can see in the picture below Scanner connecting data cable Smoke Evacuation hole The connecting base is fixed on the laser output end of the unit Generally speaking this system can be used when the laser guiding arm is connected and locked tightly to the connecting base Caution The arm can be circumvolve in a certain direction as marked on the arm 3 1 2 CO2 Laser Output Beam core Adjustment Firstly take off the laser guiding arm and equip the debugging tube on the connecting base Secondly adjust CO2 Laser device to make CO2 laser beam aim at the core of the debugging tube and make sure the beam goes through the debugging tube coaxially Thirdly switch on and select the lowest power and inspect the position of the flare of the debugging tube end by a piece of pergamyn Fourthly adjust laser device repeatedly until the CO2 Laser beam go into from the core of the debugging tube beginning and go out from the core of the ending At last take off the debugging device put on the laser guiding arm and lock it tightly The process of indication adjustment of isotopic light route is the sam
23. sts inside the apparatus so that unspecialized technician is not allowed to open up the cabinet in order to avoid electric shock danger If extraordinary noise and smell is found when the apparatus is working the apparatus must be stopped for inspection immediately Power should be cut off before inspection The apparatus assembles glass laser tube inside So pay attentions not to fall down when transport it Warning Any operation against the instructions of this Manual would possibly result in injury or danger Safety In consideration of the user s safety the machine is designed to minimize the harm of strong light to people and environment Improper operation would result in severe injury to customer operator or environment For your safety please pay much attention to the followings Security of laser Light The wave length of CO2 laser is 10 6um Warning The window outputting laser light is installed at the front edge outlet of applicator tool ADo avoid the strong optical radiation from the window Warning All operators working within the irradiated space of strong light must wear protective glasses A Don t directly see the laser light from the front edge outlet of applicator tool A Keep combustible and detonable stupefacient fluid and gas such as alcohol ether laughing gas and oxygen far away from irradiation space of laser light where appropriate measurements of protection should be taken A Try to avo
24. y discomfort at this soft setting e6 Treatment of wrinkles Power setting needs low The index setting will vary according to skin type and depth of wrinkles Reduce the index setting to increase the exposure time and spot penetration The new index setting is when the patient feels bearable discomfort but no pain For treatment of deeper wrinkles prescribe an oral painkiller 1 hour prior to the procedure This will enable the patient to sustain a lower index e7 Treatment of acne scars Index setting needs low The power setting will vary according to skin type and severity of the acne scars Increase the power setting until the desired effect on tissue is achieved The patient should feel no pain For treatment of deeper scars prescribe an oral painkiller e8 1 hour prior to the procedure This will enable the patient to sustain a higher power Set the scan area e9 After fractional resurfacing the laser can be switched to traditional CO2 mode for ablation of skin growths e g skin tags seborrheic keratoses etc or to traditional resurfacing mode in selected areas Section 3 Post treatment e1 Do not wipe the treated area The scar will promote the healing process The patient will experience a burning sensation on the skin that lasts between 30 minutes and 3 hours e2 Apply a fragrance and preservative free moisturizer to the treated area After one to two days the erythema will be replaced by a progressively darkening
Download Pdf Manuals
Related Search