Instruction Sheet
Contents
1. can use your iPhone P Information sent over this network iPad laptop and any other Wi Fi might be visible to others devices to connect with it Connect automatically wirelessly and start surfing the nns Internet a ff Open Network and Sharing Center This device complies with Part 15 of the FCC Rules and Industry Canada licence exempt RSS standard s Operation is subject to the Following two conditions 1 This device may not cause harmful interference 2 This Device must accept any interference received including interference that may cause undesired operation Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Canadian Department of Communications The device meets the exemption from the routine evaluation limits in section 2 5 of RSS 102 and compliance with RSS 102 RF exposure users can obtain Canadian information on RF exposure and compli ance Le dispositif rencontre l exemption des limites courantes d valu2. If there are any items missing please contact Leviton immediately Quick Installation Guide 300Mbps Dual Band 802 11n Wireless Gigabit Router 2 Hardware Installation STEP 1 Connect the Power Adapter provided in the 1 Package Contents package to the 47611 WG4 The Power LED on the front panel shall turn on accordingly Thank you for choosing Leviton 47611 WG4 Before installing the router please verify the contents inside the package box Wireless Router Quick Guide CD ROM y i Power Adapter Ethernet Cable STEP 2 Follow the figure below to connect the network 3 Network Configuration Windows 7 devices It depends on your network environment to connect the WAN port to a Cable xDSL modem or the Ethernet directly in your place A computer with a wired Ethernet connection is required for the first time configuration of the Wireless Router Set your computer to get an IP address from the Wireless Router Click Start button located at lower left corner of the screen Click Control Panel Double click Network and Sharing Center icon Click Change adapter settings Double click Local Area Connection icon Select Internet Protocol Version 4 TCP IPv4 and click Properties button USB Storage Select Obtain an IP address automatically and USB Line Obtain DNS server address automatically then click OK button
3. anage the 47611 WG4 easily Launch the Web browser and enter the default IP address http 192 168 0 1 See E hittp 192 168 0 1 ee Wireless Router x STEP 2 When you enter into the Web User Interface please enter the User Name and Password in the login window The default User name and Password are both admin Then click Login button to continue Dual Band Wireless Router User Name Default User Name admin Password Default Password admin Login f Cancel FURTHER INFORMATION The above steps introduce simple installations and configura tions for 47611 WG4 For further configurations of Wireless Dual Band WAN LAN Firewall Virtual Server DMZ and DDNS etc please refer to the user manual in the CD ROM If you have further questions please contact Leviton Tech Support at 800 824 3005 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guaran tee that interference will not occur in a particular installation If this equipment does ca
4. ation dans la section 2 5 de RSS 102 et la conformit a l exposition de RSS 102 rf utilisateurs peut obtenir l information canadienne sur l exposition et la conformit de rf Federal Communication Commission FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment In order to avoid the possibility of exceeding the FCC radio frequency exposure limits human proximity to the antenna shall not be less than 20 cm 8 inches during normal operation 2011 E50280 010 FE
5. twice to save the configuration 4 Marvell LAN Card Properties Internet Protocol Version 4 TCP IPv4 Properties Networking Sharing General Alternate Configuration Connect using You can get IP settings assigned automatically if your network supports RJ 45 this capability Otherwise you need to ask your network administrator Ril gz j aana nemancaanl for the appropriate TP setings a Bits a j Phone Cable xDSL a a Jack Modem PC Laptop F eyeepear V JB Fie and Printer Sharing for Microsoft Networks 4 Intemet Protocol Version 6 TCP IPv6 Version 4 TCP emet Protocol Version Pv4 4 Link Layer Topology Discovery Mapper 1 0 Driver 4 Link Layer Topology Discovery Responder Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Validate settings upon exit 4 Enter into the Web Management Default IP Address 192 168 0 1 Default User name admin Default Password admin Default SSID of 2 4G default_2 4G Default SSID of 5G default_5G Default Wireless Encryption Type None STEP 1 The Web management allows you to access and m
6. use harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encourages to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio technician for help FCC and IC Statement To assure continued compliance example use only shielded interface cables when connecting to computer or peripheral devices any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment STEP 3 Once the corresponding Internet connection type is chosen click OK button to save and make the changes take effect 5 Wireless Network Connection STEP 1 Right Click on the network icon displayed in the system tray Not connected Connections are available 10 13 AM 5 3 2012 EN STEP 2 Highlight the wireless network SSID you want to connect and click Connect button STEP 3 Enter the encryption Not connected 9 key of 47611 WG4 if ifl Connections are available necessary Wireless Network Connection a You have already finished the mannas at configuration of the 47611 WG4 default 24G g Now you
Download Pdf Manuals
Related Search