User Manual - Webstaurant Store
Contents
1. e ALWAYS connect CO2 gas canisters to a pressure regulator e NEVER drop or throw the CO2 canister e NEVER connect gas canister directly to keg e ALWAYS keep CO2 canisters in a cool place 70 F 21 5 C or less and away from heat e In case of CO2 leakage ventilate and evacuate the area immediately e ALWAYS keep canister secured in an upright position e Check the Department of Transportation D O T test date on the canister neck and do not use if older than five 5 years e Return outdated canister to your gas supplier for one that is within the time limit Ol a rri UNPACKING AND SETUP This Use and Care Manual provides specific assembly cdl operating and maintenance instructions for your model Use the keg cooler only as instructed in this Use and Care Manual Before starting the keg cooler follow these mine tam important first steps 491 O PARTS P to om a Your keg cooler comes with several small boxes that JI 2 contain all the required parts and accessories Check to J make sure that you have received all of the components listed below BEVERAGE DELIVERY KIT BOX Faucet Knob te Dp ay shee ate gene tate a ek Geo 1 Piece 2 Casters amp Washers 4 Pieces 3 Retaining Strap 1 Piece 4 Hole PWS PE 1 Piece 5 Facuet Knob a ca an NAK mk 1 Piece 6 CO2 Regulator 1 Piece 7 Keg Coupler aaa wawa Wk eae PAA 1 Piece 8 Small Hose Gas L2. e Set the edge of the keg on top of the plastic protective plate located on top of keg support shelf Slide the keg back until it is fully inside the cabinet e Care must be taken to avoid damage to the temperature control and shelf tower located in the cabinet 12 See TIPS ON INSTALLING KEG TO THE CABINET inside the cabinet as shown NOTE The illustration does not show the tap installed for clarity of installation Beer Dispenser Beer Line Tower DELIVERY HOSE ARRANGEMENT NOTE Failure to route hoses properly may cause the hose to become kinked or caught in High Pressure Valve door CO Bottle Shut Off Safety Pressure Release N _ Ff Single Guage uz CO Regulator a Low Pressure Valve REFRIGERATION User Manual VANTCO OPERATING YOUR KEG COOLER e Make sure that the keg cooler is plugged in properly to a 115V 60Hz AC only electrical outlet e Make sure that the drip tray and sump are secured under the faucet e Start with a clean beverage glass that has been wetted in cold water Place the glass at a 45 angle 2 5 cm 1 in below the faucet Do not let the glass touch the faucet Open the faucet all the way e After the glass has reached half full gradually bring the glass to an upright position e Let the remaining beverage run straight down the middle This insures proper release of CO2 by producing a 1 9 to 2 5 cm 3 4 to 1 in foam head e Close the faucet completely
3. and quickly NOTE It is normal to see condensation forming around the faucet This condensation is caused by the temperature difference between the cold beverage and the inner surfaces of the faucet when beverage is being drawn through the line HOW TO REPLACE AN EMPTY CO2 CANISTER e Remove hoses from routing clips e Remove the keg then remove CO canister e Close the canister valve of the empty canister by turning clockwise until it stops e Close the regulator shut off valve by moving it to the 9 o clock position e Carefully remove regulator from the empty CO2 canister by loosening the nut with an adjustable wrench Check the condition of the gasket inside the nut and replace if necessary Return canister to your local carbonic gas source for filling We suggest looking in your yellow pages under Carbonic Gas Sources of CO2 vary from community to community but it is often available at welding supply stores and beverage distributors Remove dust cap from new canister nut if any With the canister valve still in closed position reattach the regulator to the new canister using an adjustable wrench Ensure the plastic washer is inside of the nut Tighten nut until it feels snug but be careful not to overtighten as you will damage the gasket inside the stem nut Check to make sure that the braided gas line hose is still securely attached to the regulator Open the canister valve all the way by turning counter clockwise until it
4. normal Beer drawn improperly Make sure faucet is opened all the way Close quickly when when drawn is all foam or too much foam and not enough liquid beer FLAT BEER Foamy head disappears quickly beer lacks usual zestful brewery fresh flavour CLOUDY BEER When beer in glass appears hazy not clear Creeping regulator Applied pressure is set too high Hot spots in line Tapped into a warm keg should be 1 17 C 3 5 C 34 F 36 F Centre malfunctioning Faucet is in bad dirty or wom condition Dirty glasses Applied pressure is set too low CO is cut off Loose tap or vent connectors done Replace with a new regulator Readjust regulator to a lower pressure until foam subsides When pressure is properly set you should be able to pour 10 oz of beer in five 5 seconds Make sure beer delivery line is not pinched and is fully inside the intenor of the keg cooler Wait until keg cools down to proper temperature Have keg cooler serviced to retum it to proper operating condition Thoroughly clean faucet with recommended cleaning kit Replace all wom seals Wash glasses using soap free detergent Increase pressure until beer flows at a rate of 2 oz per second Do not tum off CO supply line to keg until keg is empty and ready to be removed Increase temperature of keg cooler See SETTING THE TEMPERATURE CONTROL section Check that coupler is properly installed in keg Replace regu
5. online call 717 392 7261 You must have your order number ready when contacting Failure to contact the designated location prior to obtaining equipment service may void your warranty Avantco Refrigeration will not warrant coverage for component failure or other damages that arise under the following conditions Failure to install and or use unit within proper operating conditions specified by Avantco Refrigeration Failure to properly maintain the unit This includes but is not limited to basic preventative maintenance such as cleaning the condenser coil Products sold or used outside of the United States Additionally no claims can be made against this warranty for spoilage of product loss of sales or profits or any other consequential damages Normal wear type parts such as light bulbs and gaskets are not included in warranty coverage 18
6. service Contact a service representative to perform this operation Care and Cleaning Tips What To Use Tips and Precautions Interior and Door Soap and water Use 30 mL 2 tbsp of baking soda in 945 mL 1 qt of warm water Be sure Liners Baking soda and water to wring excess water out of sponge or cloth before cleaning around controls light bulb or any electrical part Door Gaskets Soap and water Wipe gaskets with a clean soft cloth Drawers and Bing Soap and water Use a soft cloth to clean drawer runners and tracks Exterior and soap and water Do not use commercial household cleaners containing ammonia bleach or Handles Non abrasive glass cleaner alcohol to clean handles Use a soft cloth to clean smooth handles DO NOT use a dry cloth to clean smooth doors Exterior and Soap and water Never use CHLORIDE or cleaners with bleach to clean stainless steel Handles Stainless Steel Stainless steel cleaners i Pipes Only a dishcloth Rinse with clean water and a soft cloth Use a non abrasive stainless steel cleaner These cleaners can be purchased at most home improvement or major department stores Always follow manufacturer s instructions Do not use household cleaners containing ammonia or bleach Clean stainless steel front and handles with non abrasive soapy water and NOTE Always clean wipe and dry with the grain to prevent scratching Wash the rest of the cabinet with warm water and mild liquid detergent Rinse we
7. AVANTCO User Manual Beer Keg Dispenser User s Manual 09 2015 Beer Kegs KEGRTRBLK KEGRTRSS Recommended for household use only Please read the manual thoroughly prior to equipment set up operation and maintenance 4 Ua VEE AVANTCO Table of Contents Important Safety Instructions 002 eee ees 3 Unpacking and Setup 2 aaa 5 Features ata Glance 2 0 0 ce es 6 Assembly and Installation 0000 cee es 7 Temperature Controls aaa 11 Helpful Hints 0 0 ees 12 Energy Saving Tips 20 0 e ee es 12 Vacation and Moving TIpS 000 naaa 13 Normal Operating Sounds and Sights 13 Care and Cleaning 02 00 cece eee es 14 Before You Calaanan JN AG eee we AA 15 Warranty Information 00 00 cece es 17 REFRIGERATION VANTCO User Manual IMPORTANT SAFETY INSTRUCTIONS WARNING Please read all instructions before using this unit FOR YOUR SAFETY e DO NOT store or use gasoline or other flammable liquids in the vicinity of this or any other appliance Read product labels for warnings regarding flammability and other hazards e DO NOT operate the appliance in the presence of explosive fumes e Remove all staples from the carton Staples can cause severe cuts and also destroy finishes if they come in contact with other appliances or furniture DEFINITIONS This is the safety alert symbol It is used
8. COOLER WITH KEG INSIDE lf using a hand cart load from the side Adjust leveling legs all the way up to protect floor surface during sliding or moving Pad cabinet to avoid scratching the surface NORMAL OPERATING SOUNDS AND SIGHTS UNDERSTANDING THE SOUNDS YOU MAY HEAR Your new high efficiency keg cooler may introduce unfamiliar sounds These sounds normally indicate your keg cooler is operating correctly Some surfaces on floors walls and kitchen cabinets may make these sounds more noticeable NOTE Rigid foam insulation is very energy efficient but is not a sound insulator Some surfaces on floors walls and kitchen cabinets may make these sounds more noticeable Following is a list of major components in your keg cooler and the sounds they can cause Evaporator Refrigerant through the evaporator may create a boiling or gurgling sound Electronic control and automatic defrost control These parts can produce a snapping or clicking sound when turning the cooling system on and off Compressor Modern high efficiency compressors run much faster than in the past The compressor may have a high pitched hum or pulsating sound Drain pan not removable You may hear water dripping into the drain pan during the defrost cycle a REFRIGERATION User Manual VANTCO CARE AND CLEANING Keeping your keg cooler clean maintains appearance and prevents odour build up Wipe up any spills immediately and clean the keg cooler at
9. appliance by pulling on the power cord Always grip the plug firmly and pull straight out from the receptacle to prevent damaging the power cord e Unplug the appliance before cleaning and before replacing a light bulb to avoid electrical shock e Performance may be affected if the voltage varies by 1096 or more Operating the appliance with insufficient power can damage the compressor Such damage is not covered under your warranty e Do not plug the unit into an electrical outlet controlled by a wall switch or pull cord to prevent the unit from being turned off accidentally Paga ALA ALA IMG CH ing Do not under not under Srcumtances cut OF grounding p pr ran grounding prong OFF turns off the compressor and prevents your appliance from cooling but does not disconnect the power to the other electrical components To turn off power to your appliance you must unplug the power cord from the electrical outlet ka Mi mp IMPORTANT Turning the Temperature Control to REFRIGERATION VANTCO User Manual A WARNING CO CANISTER SAFE HANDLING e CO2 canisters must be handled with extreme care They contain potentially hazardous high pressure compressed gas Make sure you read and understand all of these instructions before installation e Never attempt to refill a CO2 cylinder yourself They can be refilled at locations such as welding supply shops party stores fire supply shops or where kegs are purchased
10. ation are not problems of the past Junked or abandoned appliances are still dangerous even if they will sit for just a few days If you are getting rid of your old appliance please follow the instructions below to help prevent accidents PROPER DISPOSAL OF APPLIANCE We strongly encourage responsible appliance recycling disposal methods Check with your utility company or visit www energystar gov recycle for more information on recycling your old appliance BEFORE YOU THROW AWAY YOUR OLD APPLIANCE e Remove doors e Leave shelves in place so children may not easily climb inside e Have refrigerant removed by a qualified service technician WARNING These guidelines must be followed to ensure that safety mechanisms in this unit will operate properly ELECTRICAL INFORMATION e The appliance must be plugged into its own dedicated 115 Volt 60 Hz AC only electrical outlet The power cord of the appliance is equipped with a three prong grounding plug for your protection against electrical shock hazards It must be plugged directly into a properly grounded three prong receptacle The receptacle must be installed in accordance with local codes and ordinances Consult a qualified electrician Avoid connecting keg cooler to a Ground Fault Interruptor GFI circuit Do not use an extension cord or adapter plug e If the power cord is damaged it should be replaced by an authorized service technician to prevent any risk e Never unplug the
11. be seating properly causing the cold air from inside the keg cooler ta meet warm moist air from the outside Use another circuit If you are unsure about the outlet have it checked by a certified technician See SETTING THE TEMPERATURE CONTROL section Ensure plug is tightly pushed into outlet Checkreplace fuse with a 15 amp time delay fuse Reset circuit breaker Check house lights Call local electric company It s normal for the keg cooler to work longer under these conditions It takes four 4 hours for the keg cooler to cool down completely Warm air entering the keg cooler causes it to run more Open door less often See DOOR PROBLEMS section Adjust temperature control to warmer setting Allow several hours for temperature to stabilize Clean or change gasket Leaks in door seal will cause keg cooler to run longer in order to maintain desired temperatures Adjust temperature control to a warmer seting Allow several hours for temperature to stabilize Adjust temperature control to a colder setting Allow several hours for the temperature to stabilize Warm air enters the keg cooler every time the door is opened Open the door less often See DOOR PROBLEMS section It takes four 4 hours for the keg cooler to cool down completely This is normal while the compressor works to transfer heat from inside the keg cooler This is normal See DOOR PROBLEMS section Open the door less often See DOOR PROBLEMS se
12. ction ODOUR IN KEG COOLER Unpleasant odours Intenor needs to be cleaned Clean intenor with sponge warm water and baking soda DOOR PROBLEMS Door will not close Keg cooler is not level 15 This condibon can force the cabinet out of square and misalign the door Level the unit OJAVEE UITE REFRIGERATION VANTCO CONCERN POTENTIAL CAUSE COMMON SOLUTION SOUND AND NOISE Louder sound levels whenever keg cooler is ON Longer sound levels when compressor comes on Popping or cracking sound when compres sor comes ON Bubbling or gurgling sound like water boil ing Vibrating or rattling noise Modem keg coolers have in creased storage capacity and more stable temperatures They require a high efficiency compres SOT Keg cooler operates at high pressure during the start of the ON cycle Metal parts undergo expansion and contraction as in hot water pipes Refrigerant used to cool keg cooler is circulating throughout the system This is normal When the surrounding noise level is low you might hear the compressor running while it cools the intenor This is normal Sound will level off or disappear as the keg cooler continues to run This is normal Sound will level off or disappear as the keg cooler continues to run This is normal Move keg cooler slightly away from the wall Snapping noise COMMON DRAFT PROBLEMS WILD BEER Beer This is
13. egulator to the right of the tank e Tighten the hex nut securely DO NOT over tighten Over tightening may damage the gasket in the nut of the regulator SMALL CO2 HOSE TO REGULATOR CONNECTION e Attach wing nut on end of small hose 8 to fitting at bottom of regulator 6 Hex Nut SMALL CO2 HOSE TO COUPLER CONNECTION ji DS e Secure other end of small hose 8 to the threaded end of keg coupler 7 as shown Be Dar f sure to fully tighten fitting f E NOTE Depending on your choice of beer you may require a different keg coupler 7 Threaded Check with your local beer distributor to determine which type of system you need Connector and order additional keg couplers as needed CLEAR HOSE TO COUPLER CONNECTION Place one of the supplied rubber washers inside the wing nut on the one end of the clear hose beverage delivery line and attach to keg coupler 7 Be sure to tighten the nut securely to prevent leakage DO NOT overtighten Overtightening may damage the gasket in the nut COUPLER TO KEG CONNECTION e Align locks on keg coupler 7 with housing on top of keg and push down on the keg coupler 7 Make sure top handle is in the up position e Turn the tap head handle clockwise 1 4 turn The tap head is now secured to the keg e Pull the tap handle out and push down until it locks into place to open the port in the keg DELIVERY HOSE PRESSURIZATION e Open the CO2 canister valve all the way by turning counte
14. ine 1 Piece 9 Rubber Gasket Black 1 Piece for bottom of dispensing tower 10 Guard Rail paaa kk kaba yd 1 Piece 11 Dispenser Tower with faucet 1 Piece ed Ba f 12 C02 Canister empty 1 Piece Tower CO Canister Spare Parts 13 Bag of Spare Parts 1 Bag replacement seals and washers NOTE The box comes with a D System type Keg Coupler 7 Depending on your choice of beer you may require a different Keg Coupler 7 Check with your local beer distributor to determine which type of system you need and order additional Keg Couplers as needed a REFRIGERATION User Manual VANTCO FEATURES AT A GLANCE Features may vary according to model Faucet Handle pr ewe Dispensing Tower Faucet Top Rail 4 Drip Tray emperature Control 41 0 cm 16 1 8 in 23 5 cm 9 1 4 in 41 0 cm 16 1 8 in 28 3 cm 11 1 8 in Quarter Sixth Half Slim Quarter Barrel Barrel Barrel Barrel REFRIGERATION VANTCO User Manual ASSEMBLY AND INSTALLATION This Use and Care Guide provides specific operating instructions for your model Use this unit only as instructed in this Use and Care Guide Before starting the unit follow these important first steps LOCATION e Choose a place that is near a grounded electrical outlet Do not use an extension cord or an adapter plug e If possible place the unit out of direct su
15. it then place inside and twist clockwise until secure Use four screws to fasten the beer tap Pay attention to use the thin black gasket 9 for assembly see illustration If you find this to be a tight fit apply some soapy water to the gasket to make the tower easier to twist into place Also see illustration showing hose connections to CO2 Notches on regulator to the beer tap EN ey R ispe mbly INSTALLING THE GUARD RAIL Follow the steps below to install the casters 1 Place the guard rail on top of the cabinet 2 Align all support feet of the guardrail with the holes on the top of the unit and press down into place CAUTION Do not install the unit where the temperature will drop below 55 F 13 C or rise above 90 F 32 C The compressor will not be able to maintain proper temperatures inside the unit INSTALLATION initial clearances e Allow the following clearances for ease of installation proper air circulation and electrical connections Sides and Top 5 inches 12 7 cm Back so uceonsneene oes 5 inches 12 7 cm Fs REFRIGERATION User Manual VANTCO LEVELING All four casters of your unit must rest firmly on a solid floor Use adjustable wrench to adjust leveling screws CAUTION do not attempt to move or relocate the keg cooler with a keg inside REGULATOR INSTALLATION e Check to ensure plastic washer is inside the hex nut e Fasten the CO2 regulator 6 to the CO2 canister 12 Place the r
16. lator Retum keg to place of purchase and exchange for one that has been properly refrigerated Exchange keg for fresh one Wash glasses using soap free detergent Clean faucet with recommended cleaning kit Remove items from atop keg and place in a separate refng erator 16 AVANTCO BALETE DANGER Risk Of Fire Or Explosion Flammable Refrigerant Used To Be Repaired Only By Trained Service Personnel Do Not Puncture Refrigerant Tubing CAUTION Risk Of Fire Or Explosion Flammable Refrigerant Used Consult Repair Manual Owner s Guide Before Attempting To Service This Product All Safety Precautions Must be Followed CAUTION Risk Of Fire Or Explosion Dispose Of Property In Accordance With Federal Or Local Regulations Flammable Refrigerant Used CAUTION Risk Of Fire Or Explosion Due To Puncture Of Refrigerant Tubing Follow Handling Instructions Carefully Flammable Refrigerant Used REFRIGERATION User Manual VANTCO Warranty Information To obtain warranty service contact the location that you purchased the product from www WebstaurantStore com Call 717 392 7472 You must have your order number ready when contacting The Restaurant Store If you purchased this unit from your local store location please contact your store directly A list of store locations can be found by visiting http www therestaurantstore com store directory html www TheRestaurantStore com lf you purchased this unit
17. least twice a year When cleaning take the following precautions e Never use CHLORIDE or cleaners with bleach to clean stainless steel e Do not wash any removable parts in a dishwasher e Always unplug the electrical power cord from the wall outlet before cleaning e Remove adhesive labels by hand Do not use razor blades or other sharp instruments which can scratch the appliance surface e Do not remove the serial plate Do not use abrasive cleaners such as window sprays scouring cleansers brushes flammable fluids cleaning waxes concentrated detergents bleaches or cleansers containing petroleum products on plastic parts interior doors gaskets or cabinet liners Do not use paper towels metallic scouring pads or other abrasive cleaning materials or strong alkaline solutions NOTE If you set your temperature controls to turn off cooling power to lights and other electrical components will continue until you unplug the power cord from the wall outlet CAUTION 1 Pull the keg cooler straight out to move it Shifting it from side to side may damage flooring Be careful not to move the keg cooler beyond the plumbing connections 2 Damp objects stick to cold metal surfaces Do not touch refrigerated surfaces with wet or damp hands IMPORTANT If you store or move your keg cooler in freezing temperatures be sure to completely drain the water supply system Failure to do so could result in water leaks when the keg cooler is put back into
18. ll and wipe dry with a clean soft cloth 14 REFRIGERATION VANTCO User Manua BEFORE YOU CALL RUNNING OF KEG COOLER Keg cooler does not run Keg cooler runs too much or too long interior keg cooler tem perature is too cold Interior keg cooler temperature is too warm Keg cooler extemal surface temperature is warm Keg cooler is plugged into a circuit that has a ground fault interrupt Temperature control is in the O position Keg cooler may not be plugged in or plug may be loose House fuse blown or tipped circuit breaker Power outage Room or outside weather is hot disconnected for a period of time Doors are opened too frequently or too long Keg cooler door may be slightly open Temperature control is set too bow Keg cooler gasket is dirty wom cracked or poorly fitted Temperature control is set too low Temperature control is set too Door is kept open too long or is opened too frequently Door may not be seating property disconnected for a penod of time The extemal walls can be as much as 1 C 30 F warmer than room temperature WATER MOISTURE FROST INSIDE KEG COOLER Moisture collects on inside of keg cooler walls Weather is hot and humid Door may not be seating property Door is kept open too long or opened too frequentty WATER MOISTURE FROST OUTSIDE KEG COOLER Moisture collects on outside of keg cooler walls Door may not
19. ll be required before beverage will reach recommended temperature CAUTION DO NOT attempt to move or relocate this keg cooler with a keg inside TYPICAL BEER SERVING EQUIVALENTS OO 1 4 Keg 1 2 Keg 992 oz 28 1239 1 984 oz 56 2459 Gallons Liters 7 75 gal 29L 15 5 gal 58L Cases 12 oz 355mL Bottles 3 3 8 82 bottles 6 3 4 165 bottles Weight full 82 5 Ibs 37 kg 165 Ibs 75 kg ENERGY SAVING TIPS ky O e Install the keg cooler in the coolest part of the room out of direct sunlight and w ids pa away from heating ducts or registers Do not place the keg cooler next to heat s producing appliances such as a range oven or dishwasher ne Koy e Do not overcrowd the keg cooler or block cold air vents Doing so causes the keg ag E ENE cooler to run longer and use more energy e Organize the keg cooler to reduce door openings Remove as many items as needed at one time and close the door as soon as possible 12 REFRIGERATION VANTCO User Manual VACATION AND MOVING TIPS VACATION AND MOVING TIPS Short Vacations Leave keg cooler operationg during vacations 3 weeks or less Use all perishable items from keg cooler compartment Long Vacations Remove all food and ice if you will be gone one month or more Turn controls to the OFF position and disconnect power Clean interior thoroughly Leave door open to prevent odors and mold build up Block door open if necessary NEVER MOVE KEG
20. nlight and away from the range dishwasher or other heat sources e For optimum performance this product should only be used indoors under normal ambient conditions e The appliance must be installed on a floor that is level and strong enough to support a fully loaded unit e If the appliance has been placed in a horizontal or tilted position for any period of time please wait at least 24 hours before plugging the unit in INSTALLING THE CASTERS Follow the steps below to install the casters 1 Empty the inside of the cabinet completely and lay the Keg Cooler down on its side We recommend that you place a piece of cardboard or cloth underneath the cabinet to prevent dents or scratches 2 Insert the casters into the holes on the bottom corners of the cabinet Tighten each caster by turning the head of the bolts clockwise with a wrench not provided in the kit 3 Once all four casters have been tightened stand the cabinet in its upright position NOTE Two of the casters include locking mechanisms to ensure the unit does not slide on hard floors These two locking casters should be fastened at the front end of the unit with the unlocked casters fastened on the rear end INSTALLING THE BEER TAP Grooves to Fit Notches Turn and Lock into Position There are notches on the bottom of the dispensing tower that line up with grooves inside the opening on the top of the Keg Cooler Align the dispensing tower with the opening on the top of the un
21. rclockwise until it stops This valve seals at both the fully open and fully closed positions Failure to completely open or close the valve could result in premature loss of CO2 pressure e Open the regulator shut off valve by moving it to the 6 o clock position e Check gauge pressure Adjust the regulator adjustment knob Knob as necessary until the pressure reads between 12 to 14 psi You may first need to loosen set screw located behind knob After setting regulator to correct pressure set screw may be retightened to lock knob in place D REFRIGERATION VANTCO User Manual CO2 CANISTER TO CABINET INSTALLATION e Lift and place the CO2 canister 12 with the CO2 regulator 6 on the shelf at rear right hand corner of cabinet It is important that the canister be kept in an upright position to operate efficiently Hook one end of retaining strap 3 over metal bracket at rear then stretch around canister and hook other end over front bracket KEG TO CABINET INSTALLATION e Place the keg on the support shelf and push back next to the CO2 canister 12 See TIPS ON INSTALLING KEG TO THE CABINET inside the cabinet as shown WARNING SAFE KEG HANDLING e Installing the keg to the cabinet is a two person team effort NEVER lift a full keg alone Doing so may cause severe injury e With the door fully open and the help of another person lift the keg vertically on both sides until the keg is higher than the keg support shelf
22. stops This valve seals at both the fully open and fully closed positions Failure to completely open or close the valve could result in premature loss of CO2 pressure Open the regulator shut off valve by moving it down to the 6 o clock position Check gauge pressure Adjust the regulator adjustment screw as necessary until the pressure reads between 12 to 14 psi Tighten the adjustment lock nut e Replace keg and route hose clips 10 REFRIGERATION VANTCO User Manual TEMPERATURE CONTROLS COOL DOWN PERIOD For proper operation allow the unit to operate with the door closed for at least 12 hours before placing the keg inside KEG COOLER CONTROLS Temperature control This rotary control is the primary control for the refrigerated compartment temperature If the unit is too warm adjust this control in the Max direction If the unit is too cold adjust this control in the Min direction TEMPERATURE SETTING AND ADJUSTMENT For beer storage the recommended initial setting is Med Under most conditions this setting will provide for dispensed beer between 1 3 2C 34 38 2F You may adjust as required to suit your individual taste and the keg cooler operating conditions After a control adjustment always allow 24 hours for the beer to stabilize at the new temperature before making additional adjustments IMPORTANT Turning the unit temperature control to OFF turns off the compressor but does not disconnect
23. the power to the light bulb and other electrical components To turn off power to your unit you must unplug the power cord from the wall outlet NOTE When purchasing a beer keg always purchase a keg cold lt 38 F 3 C transport as quickly as possible and get it installed in the cold unit within two 2 hours Under most conditions these guidelines will allow serving of properly cooled beerwithin 24 hours Purchasing a keg ata temperature above lt 38 F 3 C and or exposure to elevated temperatures longer than two 2 hours will require additional time for the beer to be cooled to optimum serving temperature t REFRIGERATION User Manual VANTCO HELPFUL HINTS PARTS OF A CO2 REGULATOR A Low Pressure Gauge B Adjustment Knob C Adjustment Lock Set Screw D Shut off Valve E CO2 Nut used to connect to CO2 canister F High Pressure Gauge BEER STORAGE TEMPERATURE e Draft beer is not pasteurized so it must be kept cold preferably at 38 F 3 C Temperatures above 38 F 3 C may cause the beer to become wild turn sour and cloudy RECOMMENDED KEG HANDLING e Be sure the keg is cold when you purchase it e Transfer keg from place of purchase and install in keg cooler in two 2 hours or less e After the keg is installed in the keg cooler allow 24 hours for beverage to reach recommended temperature e If the keg is exposed to ambient temperatures longer than two 2 hours additional cooling time wi
24. to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury IMPORTANT indicates installation operation or maintenance information which is important but not hazard related INSTALLATION CHECK LIST DOORS ELECTRICAL POWER L Door seals completely to cabinet on all sides 1 House power turned on L Door is level across the top L Appliance plugged in LEVELING FINAL CHECKS LI Unit is level side to side and tilted 1 4 6mm front to back LI Shipping material removed Cabinet is setting solid on all corners Appliance temperatures set LI Registration card sent in CHILD SAFETY Destroy or recycle the carton plastic bags and any exterior wrapping material immediately after the appliance is unpacked Children should NEVER use these items to play Cartons covered with rugs bedspreads plastic sheets or stretch wrap may become airtight chambers and can quickly cause suffocation REFRIGERATION User Manual VANTCO PROPER DISPOSAL OF YOUR APPLIANCE RISK OF CHILD ENTRAPMENT Child entrapment and suffoc
Download Pdf Manuals
Related Search