STAGE 12P DMX - AV-iQ
Contents
1. Audio Effect Programming The Audio Mode could be programmed to flash desired channels to the intensity of the Audio signal whenever the Audio Mode is on by following these steps 1 Tap the Program key until its LED lights If the LED does not light the memory lock is on Program 2 Select channels to be affected by audio by moving a the corresponding channel Faders to the maximum j and move other channel Fader to minimum 2 2 3 Tap the Audio key to program the audio intensity into memory Operation Run a Pattern Run a pattern with Speed Fader Tap the Pattern key stored your desired program to run and its LED lights Move Speed Fader to adjust to your wanted value Run a Pattern at audio effect 1 Tap the Audio key to enter Audio Mode udio 3 Move the Audio Fader slowly up until the desired e effect is reached j Th Operation MIDI In amp Out After turning off the power press and hold Built in keys 5 6 7 8 at the same time Continues to hold these keys and then switch on the power You will be allowed to set the states of MIDI and value display mode indicated by Pattern LED 1 2 3 and 4 flashing Press Pattern key 1 to access the setting state of MIDI Receiving The LED will show IN XX and XX refers to the relative receiving channel 1 122. FLASH gt the successful storing And the LED will show the present step number for quick programming Operation Programming Note If there can be Flash key keys in the holding state this unit will wait for you to release it them for storing the scene Repeat step 3 and 4 until all desired steps are include in the chase Note Every Pattern can record no more than 100 steps Tap the Blackout key to exit Program Mode Fader Programming Static Scenes or Chase Sequences with adjustments of levels may be programmed into any of Patterns using Channel Faders Press Program key until its LED lights up If its LED is off indicating that the program may be locked Select the pattern to program by tapping one of the 16 Pattern keys and its LED will start to flash Program K Operation Programming 3 Move the channel level Fader to the desired level for this step Note Channel LED does not light up except in Manual Mode 4 Press Program key and this step will be automatically programmed into memory 5 Repeat step 3 and step 4 until all your desired steps are completely programmed Note Every Pattern can record no more than 100 steps 6 Press Blackout key to exit Note Quick programming and Fader programming can be used together according to your requirements Operation
3. Press the Pattern 7 Pattern 8 to increment decrement the channel number to the desired receiving channel of MIDI Press Blackout key to confirm the new setting and automatically return the previous setting state Press Pattern key 2 to access the setting state of MIDI transmitting The LED Display will show OU XX and XX refers to the relative transmitting channel 1 12 Press the Pattern 7 Pattern 8 to increment decrement the channel number to the desired transmitting channel of MIDI Press Blackout key to confirm the new setting and automatically return the previous setting state Value display settings decimal and percent mode Pressing pattern 3 will allow to set the decimal display mode Then the LED displays 255 Press Blackout key to confirm the new setting and automatically return the previous setting state And pressing pattern 4 will enable the percent display mode indicated by the LED displaying 100 Also press Blackout key to confirm the new setting and automatically return the previous setting state 5 Press the Blackout again to exit from this setting state Operation MIDI Transmitting amp Receiving This unit can transmit and receive Note On Off data to enable some preset functions NOTE NUMBER VELOCITY FUNCTION 22 45 Turn on or off patterns 1 24 46 57 channel intensity Turn on or off channels 1 12 62 64 Turn on or off Add State 1 3 65 DARK 66 FULL ON 67 Manual Function 68 Activa
4. LED light up In the Manual State each channel controls its channel intensity A second tap of Manual key or Blackout key can turn off Manual State Note In manual Lock State a second tap of Blackout key can not turn off Manual State Main Function Audio key Fader Audio chase sync may be activated by tapping the Audio key indicated by Audio LED lighting up Then adjusting the sensitivity control for desired effects The patterns will sequence on the audio beat In this case the Tap Sync key and Speed fader can not affect these patterns Audio intensity effects may be programmed into any channel by Program key This can enable the desired channels to flash following the audio signal whenever the Audio mode is on Tap Sync The Tap Sync key is used to set and synchronize the chase rate the rate at which all patterns will sequence by pressing the key several times The chase rate will synchronize to the interval time of last two taps The LED above the Tap Sync key will flash Tap Sync key will override any previous setting of the chase rate control Fader until the Fader move again Blackout Each tap of Blackout key will clear or deactivate functions in the following order Program mode Go Function Patterns and Manual Mode The Blackout LED will light up when all the above function completely deactivated Lights affected by each function will fade out at the set fade rate Main Function Master Fader Pushing t
5. WORK STAGE 12 P DMX 12CH Dimmer Console USER S MANUAL Contents General INStruCtiony EE 1 Safety vide del 2 Efront Panel cece Nane me n n a Ai 3 Rear Panel ee 6 Main laten le EE 7 JsCirii en nG NEGBIRARNA SA QMq B N RE gt E DE EKE 13 Programming S2 wara W D NNN NNN 13 Quick Programming enee 13 Fader Programming zess 14 Audio Effect Programming senn 16 Run a Pattern Run a Pattern with Speed Fader unenee 17 Run a Pattern at audio effect d kwa ye xuza k eway A ke Kaw e ewk Bawa Z ke N GE 17 MIDI IMR OUt e n 18 MIDI Transmitting amp Receiving KEE 19 Power Input Wiring ssia 20 Technical Specification de j ee 21 General Introduction Thank you for purchasing this WORK product STAGE 12 P DMX This unit provides 24 patterns and 12 channels tocontrol various lighting devices The main features are that simple free programming 12 Dimmer Packs and the embedded functions e g Stand By Audio Tap Sync Dark Full on Blackout Main Features 12 Channel DMX Dimming Console 16 programable patterns and 8 built in patterns Audio Speed Fade Time and Master Control 12 free adjustable Faders Sound active Quick programming and Fader programming Catch and hold the present scene temporarily Fog Machine trigger Remote control in connection with foot switch USITT DMX 512 protocol with 3 pin XLR Safety Instructions Read the instruction in this manual caref
6. by fails in Full on state Its LED will flash when stand by state is activated Manual Program Lock Press and hold Step key and Blackout key their LEDs will flash at the same time Do not release and press the Manual Program key The LED shows On Off which indicates Manual Program Lock or Unlock states In Manual Lock State Black out key can not control and only pressing the Manual key can turn off Manual State While in Program Lock State any entry key for programming will be disabled And only setting the unlock state can allow to use Program function Erase all recorded chases Press Pattern key 3 6 10 and 15 Do not release and turn off the unit Turn on the console again after several seconds and all recorded chases will be deleted Note Deleted chases can not be recovered Please be cautious when performing this function Operation Programming Quick Programming 1 Press Program Key to enable Program function e indicated by its LED lit up Note If the LED can t be on Program Key may be rogram set in Lock State see Lock Function 2 Select a desired Pattern for program and press it Its LED will flash indicating that Program Mode can be active EI 3 Press and hold the desired Flash key keys as a scene 4 Releasing these Flash key keys will automatically record the present scene asone step ofthe chase All LEDs of 24 patterns will havea flash indicating
7. his fader can control the maximum output of 12 channels The output of each channel can t be beyond the set max value However pressing the Flash key or Full key may change the output temporarily Fade Time Fader This Fader is used to adjust Fade Time The time changing of 12 channels intensity can be determined by this function But when the Flash key or MIDI key is enabled the present Fade Time setting can not be used at all If the LED shows 1 1 it represents 1 1second and if it shows 1 10 the fade time is 1 minute and 10 seconds Fade time ranges from 0 to 10 minutes Speed Fader Pushing this fader up down to the desired position can adjust the rate of chase The rate must range from 0 05 second to 10 minutes If the LED shows 1 10 it indicates that the rate can be 1 10 seconds And when the LED shows 1 10 it means that the rate can be one minute and ten seconds Power A B Power A indicates the work state of phase A When its LED lights up phase A can be powered on On the contrary there is no electricity passing in phase A Power B indicates the work state of phase B When its LED lights up phase B can be powered on On the contrary there is no electricity passing in phase B Main Function Remote Control Connecting a foot switch will give a remote control of Full on and Stand by states Full on makes all channel outputfull on Stand by shuts down output but do not affect the intensity of LEDs Stand
8. n patterns stored in the unit 5 Add Keys The 3 Add keys are used to set modes of the patterns in rows between Single Mix mode and Kill mode Front Panel 6 10 11 12 13 14 15 16 17 18 Fog Machine Key Stand By Key Tap Sync Key Glide key Step key Program key Go key Dark key Manual key Full on key Audio key Blackout key LED Window This key can trigger the external connected Fog Machine indicated the states heating and ready by two separate LEDs This key can enable disable the Stand By function which can shutter all the outputs Repeatedly tap the key establishes the chase rate Enable the Fade Time between the two steps in the Glide Mode Press this key to go a step of a chase Set Lock Function when combined with Blackout key Press to enter Program Mode Press this key to hold the set channel intensity Press to turn off all output When this key is pressed down real time operation of the channel Fader level will be provided Press to output all at full intensity Activate audio sync of chase rate or set a scene at audio effect This key is used to clear Program Go Pattern Manual Mode When used with the Step key Lock function is enabled to be set It shows current programming or function state including Program Lock State Manual Lock State MIDI Receive State and also reads some relative values like dimmer chase rate steps of a
9. programming chase etc Front Panel 19 20 21 22 23 Kill Key It can enable disable the Kill mode Audio Fader It can control the sensitivity of the audio automatic gain control circuit Adjust it for best effects with external audio device Speed Fader This fader controls the speed of the patterns chases or sets the Fade Time in the Glide Mode Fade Time Fader It can set the initial fade in and out of a chase Go function Manual state etc Master Fader Pushing the Master fader can control the output values of allthe 12 channels Rear Panel 1 Channel Output 2 Audio input 3 Fog Machine Connector MIDI In 4 5 MIDI Out 6 MIDI Thru 7 8 DMX Out Remote Control 9 DMX Polarity Select 10 Power switch 11 Channel Fuse This unit provides 12 Dimmer packs for easy and convenience operation Audio input line for music signals or built in microphone signals with amplitude ranging from 100mV to 1v Connects with a fog machine MIDI data input MIDI data output MIDI data transmitting Standard DMX signal output Connects a remote controllerto enable Stand By and Full On function Used to select DMX polarity Switch on off this unit F6 3A CH 250V 5 x 20mm 12 Power Input AC 230V 50Hz 16A PHASE Max Phase A CH 1 6 Phase B CH 7 12 Main Function Patterns 16 8 There are total 24 patterns in charge of pattern keys in which 16 a
10. re edited programs and the other 8 are built in programs chases For the built in patterns they can be selected for application complying with the real controlled channels of external lighting devices Pattern Number Way Number Channels of lighting device Pattern 1 2 4 way 4 channels Pattern 3 4 6 way 6 channels Pattern 5 6 8 way 8 channels Pattern 7 8 12 way 12 channels A tap of any of the patterns keys will light the pattern LEDs and causes the scene or chase stored in memory to fade at the set fade rate A second tap will cause Pattern LED to go off and the current channel LEDs will fade out at the set fade rate 24 Pattern keys are arranged with 3 rows and each row has an Add key which determine Kill Mode or Add Mode Pattern key works normally in the Kill Mode whereas pressing one key will disable other patterns that are active and cause them fade out while the selected pattern fades in Pressing the Add key will put the patterns in the Add Mode and all patterns will operate independently of each other Main Function ADDs 3 The Add mode is activated by pressing the Add key When the Add mode is turned on multiple patterns of the row will be selected every time Add mode consists of Single and Mix modes Single mode Press the appropriate Add key indicated by the ADD LED flashing The Single mode is active Tap the desired Pattern keys in the row the patterns will chase in sequence from left to right Mi
11. te Glide function 69 Turn on or off AUDIO 70 Step 71 BLACK OUT 72 Standby Power Input Wiring Two phases input Wiring L1 lt L1 Power input L2 lt L2 ac 230V 50HZ N lt N Earth lt Earth Technical Specifications Power input Channel output Audio input MIDI in out thru DMX output Remote control Cooling Circuit fuse Channel fuse Dimension Weight CE CHINA Power Input AC 230V 50Hz 16A PHASE Max Phase A CH 1 6 Phase B CH 7 12 1 5 A CH 6A total CH 1 6 1 5 A CH 6A total CH 7 12 5A CH 16Atotal CH1 6 5A CH 16A total CH7 12 Line input 0 1v 1Vp p 5 pin Multi connector 3 pin XLR female socket 1 4 stereo jack Powerful fan thermo controlled F1A 250V 5x20mm F6 3A 250V 5x20mm 482x266x182mm 8 6 kg C WORE k k ewrs resenven REV 1 1 Apr 2003 24 004 0976
12. ully and throughly as they give important information regarding safety during use and maintenance Please keep this manual with the unit for reference in the future N Warnings Be careful of high voltage connected with this unit e DO NOT make any inflammable liquids water or metal objects contact the unit e STOP using the unit immediately in the event of serious operation problem and contact your local dealer without hesitation e DO NOT open the unit there is no user serviceable parts inside NEVER try to repair the unit yourself IT Cautions e This unit must be earthed e Be sure that your product is not damaged and all accessories are not missing This unit must only be operated by adults DO NOT allow children to tamper or play with it e DO NOT dismantle or modify the unit when charging it e To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Front Panel 1 Channel Faders These 12 Faders can adjust the levels of each channel to control the intensity of external lights fixtures indicated by 12 LEDs related to the specific channels 2 Flash Keys These 12 keys are used to give an individual channel a full intensity and also used for quick programming 3 Pattern Keys The 16 Pattern Keys are used for activating any of the 16 static scenes or chase patterns which have been programmed before 4 Built in Pattern Keys The 8 keys can activate built i
13. x mode Press the appropriate Add keys until the ADD LED lights the Mix mode is active Tap the desired Pattern keys in the row the patterns will chase in unison To change between Single and Mix mode press the appropriate Add key until its LED lights flashes from flashes lights Kill Press Kill key until its LED lights In Kill Mode pressing any Flash keys will disable any other channel outputs A second tap of Kill key will return normal Add Mode in which tap of any Flash keys will not affect other outputs Main Function Glide The Glide key is used to turn on and off the Glide Mode When the Glide is activated any pattern selected will fade in afer the previous pattern The rate of the change is determined by the Speed fader between steps chase rate Press the Glide key again to exit the Glide mode And turning on or off the Glide Mode will not affect patterns that are already running Go The Go key causes all channels to fade to the present level represented by the setting of the Channel Fader The lighting level will be added to the present scene Compared to the present level of each channel the higher level of each corresponding channel of any other active scenes or functions will have precedence to control the intensity Pressing the Go key additional times will cause the old scenes to fade out and the new scenes to fade in A tap of Blackout key will cancel Go State Manual Press Manual key until its
Download Pdf Manuals
Related Search