Model SAF206S Electronic Siren
Contents
1. MOMENTARY FOOT SWITCH HRT VDC Switching example 22 AWG GRAY x2 Connect to output jack ter minals or speaker of radio 22 AWG YELLOW 1 E HRT VDC Switching example Must set HRT_N option switch LV3 LV2 LV1 2 O o 0 COREE POWER IN 1 nw OAA COUMRaSOYERE QazZzununwuwraracnc SIREN FUSE O e ew ew oo O 4 SAF2068 20A Automotive y Type Fuse 12 P Terminal Block Plug Plug installed this orientation The leads and recommended colors shown are user supplied Recommended Wire Size Use next larger size if longer than 10ft SAF206S Siren_v 1 LIGHT CONTROL CONNECTIONS Power The power input for the light controls the lever switch and the six auxiliary control switches are separate from the power inputs for siren This design helps prevent a fault in one main circuit from affecting another main circuit Fuses Breakers Each light control output is fused and should be limited to 10 Amps Proper rated circuit breakers should be connected between the power source and light control power inputs WARNING Improper circuit breakers or fuses can result in damage to the unit and or vehicle Lever Switch 8 Light Control Connections Load LV1 10 Amps Max Load SW4 Load SW3 10 Amps Max Load LV2 10 Amps Max Load SW5 Load Sw2 10 Amps 10 Amps Max Max Circuit B2. Model SAF206S Electronic Siren Installation and operation manual Notice to installer Before installation and use read all instructions and warnings Deliver this manual to the end user of this equipment Doc No SAF206S Siren_v 1 Table of Contents GENERAL DESCRIPTION ccs sissc cisceniisotenueccnevtessates sabeesaesesdsertdenaccsvnsdsides diante basis 2 SPECIFICATIONS vrs iaieecas cee cfttuse cake ii 3 INSTALLATION bch oi a aa 4 CONTENTS aiii la tddi 4 MOUNTING st iics docstoc tito id Lg 4 W Bra CK itest ccc ccsacc venassctasscancetacestuners aaar Ea neared 4 Console Motivar in ieee ed 4 Microphone GlDE om it ito E 4 WIRINGiiiiaronassaiana loa 5 Electrical ConNECtON Sureste cla 5 Light Control Connections macs ia 7 PROGRAMMING iramane sasons neontetraa yates nee liada 8 OPTION SWITCHES ipri iniiae sa nena ea a eaea aaie ea 9 OPERATION arae a E a das a aeaa lia aE a A a N 10 POWER VON ORF 3 caia aia 10 SIREN CONTROLS occiso riada 10 Rota S WICC arire adios da 10 Manual Butto Msema a ee 11 FIOM BUON criticar repisa 11 PA sia Aa 11 FLIRT Input Optional siisii aaaea 11 PKL Input optional cia HE A ee he 12 Time Override Opona lisissa natsa ie aaa 12 EIGHT CONTROLES out E a Ea dei acido 12 LEVER SWITCH seciecscnsstenssctecdeeenteeal cnsdeas ern elias reen aeii as ie oiiire EEs 12 AUXILIARY SWITCHES ii ccisnces ccs Gass cccaviessscendetcaateadectaddecie caselecisinssntsedinseceesensipas 12 TROUBLESHOOTIN
3. phone for PA use and push button override The SAF206S also includes a 4 position slide switch for primary lighting system control and 6 independently controlled switches each control switch is capable of 10 amps current There are 6 primary operation modes PHASER YELP WAIL STBY HF and RADIO with a HORN button and a MAN button override The Phaser tone can be replaced by HiLo tone or disabled entirely A Horn Ring Transfer input is available for the connection to vehicle horn ring or remote switch for hands free siren operation A Park Kill input is available for connection to a door switch etc to stop siren tones when exiting the vehicle A Video trigger output is available for activation via lever switch or auxiliary switches front view AXIX TECH swi sw4 RADIO WAIL PHASER rear view Lo xx ear LV3 Lv2 LV1 C l SAF2065 POWER IN SIREN FUSE side view DIP switches O vaagaada roent TA SAF206S Siren _v 1 SPECIFICATIONS Input Voltage 10 16 VDC negative ground n iren Input Current 8 5Amps 13 6VDC single 100W speaker 16Amps 13 6VDC dual 100W speakers Siren Standby Current Less than 300mA Audio Frequency 200Hz 10kHz 3db Siren Output Power 40 watts 13 6VDC singl
4. PKL Input optional The Park Kill input may be connected to the vehicle door switch or other switching device to turn off any siren tone when activated It can also turn off the light control by setting the DIP SW1 3 PKL_O1 option Also the siren tone may be set to remain off until a siren control is changed or until the PKL input is deactivated by setting the DIP SW1 4 PKL_O2 option see OPTION SWITCHES section Timed Override optional With Rotary Switch in WAIL YELP or PHASER mode momentarily pressing the MANUAL button will toggle between tones overriding the Wail Yelp Phaser tones The unit can be set to automatically go back to the original tone after 10 or 20 seconds by setting the DIP SW2 4 MAN_T option see OPTION SWITCHES section LIGHT CONTROLS The 4 position lever switch is used for the primary lighting functions It provides automatic activation of the siren There are additional 6 programmable on off buttons for auxiliary lighting or other device controls LEVER SWITCH The lever switch can be set to operate as a Progressive or Non progressive switch Progressive Non progressive Switch There are 4 different settings available This is configured by setting the DIP SW1 5 LV_P and DIP SW1 6 LV_N option see Lever Switch Modes chart At each of the 3 lever positions it is possible to program the additional AUX on off buttons to be activated together Lever Switch Position 3 At this position the siren tone
5. under OPTION SWITCHES section SIREN CONTROLS ROTARY SWITCH The rotary switch controls the primary operating modes of the siren CONTROL BUTTON CORRESPONDING TONES CHART Rotary Switch Tone MAN button PKL MIC HRT HORN button RADIO WAIL WAIL YELP HORN HF WAIL MANUAL SIREN HF STBY WAIL WAIL YELP SILENT PA HORN HORN WAIL WAIL WAIL YELP YELP YELP YELP PHASER PHASER PHASER PHASER YELP SAF206S Siren_v 1 foe OPTION SWITCHES Various options can be selected DIR Sw PISA by turning on or off DIP switches en DIE ON DIP located on the side of the siren The DIP SWITCH functions are 12345678 1234567281 described below DIP SW1 1 HRT_N HRT Input Polarity The HRT input is normally activated by a positive voltage Set switch on to activate with negative DIP SW1 2 PKL_N PKL Input Polarity The PKL input is normally activated by a positive voltage Set switch on to activate with negative DIP SW1 3 PKL_O1 PKL Option1 With this switch off only siren tone is shut off when PKL is activated Set this switch on to shut off siren tone and light control DIP SW1 4 PKL_O2 PKL Option2 With this switch off siren tone remains off until siren control is changed With this switch on siren tone resumes as soon as PKL is deactivated
6. DIP SW1 5 LV_P Lever Progressive See Lever Switch Modes chart DIP SW1 6 LV_N Lever Non Progressive See Lever Switch Modes chart LEVER SWITCH MODES CHART LV_P OFF LV_P OFF LV_PON LV_PON cee LV_N on LV_N A LV_N OFF LV_N on Lever Position LV_MODE1 LV_MODE2 LV_MODE3 LV_MODE4 OFF OFF 1 LV1 LV1 LV1 LV3 LV1 2 Lv2 Lv2 LV2 LV3 LV1 Lv2 3 LV1 gt LV2 gt LV3 LV3 LV1 LV2 LV3 LV1 LV2 LV3 DIP SW1 7 AUTSR_D See Code3 mode 8 AUSTR_D OFF DIP SW1 8 INST_ON The Enable input is normally required to turn on the unit Setting this switch on allows the lever switch to turn on the unit without the Enable input SAF206S Siren_v 1 AMPLIFIER CONNECTIONS 14 AWG RED x2 Use second lead for dual speaker ENA 22 AWG ORG 14 AWG BLK x2 Use second lead for dual speaker Unit Enable like an ON OFF switch Connect to positive circuit fuse panel controlled by ignition or other switch VID 22 AWG BLU Connect to camera input dual speaker connect to 18 AWG BRN x2 16 AWG dual speaker 1 ADDED DOOR SWITCH DOME LIGHT PKILL VDC Switching example PRICE 22 AWG WHITE VDC Switching example Must set PKL_N option switch
7. 1
8. G gs ccciciaccci ancianidad il 13 SAF206S Siren_v 1 TROUBLESHOOTING SAF206S Siren has been designed to provide reliable quality service under the worst condtions If encounter any difficulties check its installation or speakers The following table represents problems and probable causes PROBLEM POSSIBLE CAUSE No sound Loose wires or connectors Bad speaker driver High input voltage greater than 16V Fuse ruptured short circuit Vehicle supply fuse open PA Volume knob in lowest position if DIP SW2 8 SR_ADJ on No siren tones Microphone button pressed High input voltage greater than 16V Speaker not connected Open circuit in speaker wiring Defective speaker Distorted sound Bad speaker driver Damaged or loose speaker housing or tip Low voltage to siren amplifier Loose wires or connectors at ENA or SPKR Speaker connected to wrong tap High resistance in speaker wiring Low voltage to siren Speakers not properly phased PA Volume knob in low position if DIP SW2 8 SR_ADJ on Siren volume low Weak PA Microphone no held close to mouth Defective microphone Microphone loose connection Intermittent High input voltage greater than 16V Bad speaker driver Unused wires touching vehicle ground or supply SAF206S Siren_v 1 213 GENERAL DESCRIPTION The SAF206S Siren Amplifier is a premium 200W unit designed for single or dual 100W speaker use with full lighting control The siren comes with a noise canceling micro
9. ault RED Steady PUSH ON PUSH OFF w VID trigger RED Slow Flashing MOMENTARY RED Quick Flashing TIMED MOMENTARY 10 or 20 seconds NOTE The Timed Momentary operation typically used as a Gun Lock Timer must begin with switch 6 If switch 6 is programmed as timed momentary only then switch 5 may be programmed also as a timed momentary and so on Each lever switch position 1 2 or 3 may be programmed to automatically turn on any of the auxiliary switch controls except Timed Momentary Gun Lock Timer These auxiliary switch controls may still be operated manually even if they were turned on automatically Each time the lever switch changes position the combined auxiliary switch controls are turned on or off When the lever switch is turned off the entire auxiliary switch controls tied to a position on the lever switch is turned off while the other auxiliary switches are unaffected Set Lever Switch Position 1 2 3 and Auxiliary Switch Combination 1 Set the lever switch to the desired position to the program 2 Press the desired auxiliary switch to change LED color to Red Press the auxiliary switch again to change LED color to Green to remove from combination 3 Once the switches are programmed as desired save and exit programming mode by turning DIP SW2 7 PRG switch OFF NOTE If the unit is turned off before the DIP SW2 7 PRG switch is turned off the new programming will not be saved SAF206S Siren_v
10. ccessed by the vehicle operator Make sure to not mount in an area that would affect the vehicle the air bag U Bracket Position the U bracket in the selected mounting location and drill mounting holes Then secure the U bracket to the vehicle and the siren to the U bracket Console The siren can be mounted into the console by using the hardware supplied by console manufacturers The siren is secured onto the console brackets the same way as the U bracket Microphone Clip Select a good location for mounting the microphone clip for easy accessibility of the microphone WARNING Do not interfere with the proper operation of the vehicle airbag deployment system SAF206S Siren_v 1 WIRING Use wires that are capable of handling the required current Route the wires properly to prevent wear overheating and interference with air bag deployment Ensure that all connections are tight and double check wiring before connecting to the vehicle battery ELECTRICAL CONNECTIONS Electrical connections to the unit are made by using block plugs and screw terminals located on the rear Route all wiring to the siren and secure onto block plug termi nals then plug onto the siren The plug can be easily removed without unwiring when the unit requires servicing The power supply for the fused amplifier 12 P plug must be capable of delivering peak currents up to 50A for adequate short circuit protection and proper operation It is recommended t
11. e 100W speaker Siren Output Power 100 Watts RMS MAX 14 VDC single 100W speaker 200 Watts RMS MAX 14VDC dual 100W speakers Siren Frequency 725Hz 1465Hz Tones Cycle Rates Horn Wail Yelp Phaser HiLo Cycle Rates Composite Constant 12CPM 190CPM 650CPM 60CPM Operating Temp 30 C to 65 C 22 F to 150 F Siren Controls 6 position rotary mode switch Radio HF STBY Wail Yelp and Phaser Momentary push button Horn switch Momentary push button Manual Tone toggle switch ENA input positive to turn on unit HRT input programmable for positive or negative operation PKL input programmable for positive or negative latching operation Side DIP switch option selectors Siren Controls 4 position lever switch with position 3 siren activation and LED indicators 6 on off lighted push button switches with replaceable legends Light Output Ragings 10A fuse on each of the 9 outputs 6 push buttons 3 lever positions Siren Connections Positive x 2 Negative x 2 Speaker x 2 Radio x 2 Enable Video Park Kill ee Block Horn Ring Transfer Light Control Power In 2 position screw terminal inputs Connections LV1 LV2 LV3 lever switch 3 position screw terminal outputs SW1 SW2 SW3 SW4 SW5 SW6 push buttons 6 position screw terminal outputs Size 16cm x 18 5cm x 21 5cm Boxed Weight 2 5kg SAF206S Siren_v 1
12. is automatically activated This function can be disabled by setting the DIP SW1 7 AUTSR_D option see OPTION SWITCHES section Video Trigger Output The video camera trigger output is activated with the lever switch in position 1 2 or 3 The AUX Switches will also activate trigger Function OFF Position 1 Position 2 Position 3 PKL Depends on setting ON ON ON of auxiliary switches VID Trigger has no effect AUXILIARY SWITCHES The 6 lighted on off switches are for controlling other lighting functions or devices The switches can be programmed for different functions and changes from Green to Red when activated They may also be combined with each lever switch position to automatically be activated SAF206S Siren_v 1 RADIO This function amplifies the radio speaker input for re broadcast outside the vehicle It is also known as Radio Re broadcaster and no siren tones are available in this position The Radio Volume can be adjusted via the PA volume switch HF This is a standby position dedicated for HRT Horn Ring Transfer When installing the unit the auxiliary input must be connected to the horn ring or other switching device Tap the horn ring once to activate Wail tone then tap again to activate Yelp tone then tap again to activate Phaser tone and quickly tap the horn ring twice to shut off siren tone Constantly press and hold the horn ring will produce Horn tone until released then the si
13. nect to radio output terminals or its speaker The Radio volume can be adjusted by using the PA Volume control knob on the front panel VID Output Connection A Video Camera trigger output is activated with the lever switch or programmed auxiliary switches SAF206S Siren_v 1 DIP SW2 1 HORN_D Horn tone is disabled by setting this switch on DIP SW2 2 PHASER_D Phaser is disabled by setting this switch on DIP SW2 3 HILO HiLo Tone replaces Phaser tone by setting this switch on DIP SW2 4 MAN_T With this switch off the next siren tone is activated when MAN button is pushed With this switch on the next siren tone is activated momen tarily for 10 or 20 seconds when MAN button is pushed DIP SW2 5 TMR Timed momentary auxiliary output is on for 10 seconds set this switch on for 20 seconds DIP SW2 7 PRG Turn this switch on to enter PROGRAMMING mode see PROGRAMMING section DIP SW2 8 SR_ADJ The siren tone volume is adjustable by setting this switch on Use PA Vol knob to adjust volume OPERATIONS POWER ON OFF The unit can be activated by applying positive voltage to the ENA terminal in the rear Normally this is wired to the ignition switch of the vehicle it can also be wired to another switch to act as ON OFF See Amplifier Connections Diagram The unit can also be configured to activate with the lever switch without applying positive voltage to the ENA terminal See DIP SW1 8 INST_ON
14. o wire directly to the vehicle battery WARNING Ensure that all wires are firmly secured onto the block plug and plug is firmly secured onto the siren Wire Size and Termination The AMPLIFIER CONNECTIONS diagram shows the minimum size of the wires used for each connection along with recommended lead color If the wire is longer than 10 ft use the next larger size ENA Input Connection This serves as the power switch for the entire unit Connect to a positive circuit controlled by the vehicle ignition switch usually a terminal at the vehicle fuse panel It is not recommended to make permanent power connection as this may drain battery The lever switch may also be setup like a power switch see DIP SW1 8 INST_ON under OPTION SWITCHES section HRT Input Connection The Horn Ring Transfer input allows activation by an external source of either the Horn or other function It can be set for positive or negative switching see DIP SW1 1 HRT_N under OPTION SWITCHES section PKL Input Connection The Park Kill input may be connected to the vehicle door switch or other switching device to turn off any siren tone when activated It can also turn off the light control by setting the DIP SW1 3 PKL_O1 option Also the siren tone may be set to remain off until a siren control is changed or until the PKL input is deactivated by setting the DIP SW1 4 PKL_O2 option see OPTION SWITCHES section RAD Input Connection Con
15. reaker Limit input up to 50 Amps Max Internal screw pressure terminal will accept up to 6 AWG for input current higher than 50 Amps Load SW6 Load SW1 10 Amps 10 Amps Max Max Load LV3 10 Amps Max Recommended Wire Size Use next larger size if longer than 10ft SW6 SW5 SW4 SW3 SW2 SW1 LV3 LV2 LV1 O O o o PE E E E QQ amp nnoors aa POWER IN Seur isoZzE22 L0LQ0ZZ0N QU gt OA TITO On SIREN FUSE O ei ea a E ew ala o SAF206S Siren_v 1 PROGRAMMING Once the electrical connections are made and the power is available to the unit each position of the lever switch and six auxiliary control switches are ready to be programmed The programming mode is entered by changing the DIP switch Follow these steps to program the unit Get into program mode 1 Turn unit on with enable input or lever switch 2 Enter the program mode by turning DIP SW2 7 PRG switch on Set Auxiliary Control Switch Operation Lever Switch in OFF Position 1 With Lever switch in off position each auxiliary switch current operation program status is indicated on the face of the unit using colors and flashing See the table below for switch status definition 2 Change switch operation by momentarily pushing the switch LED showing AUXILIARY button setting GREEN Steady PUSH ON PUSH OFF def
16. ren will return to its previous siren tone STBY This is a silent mode that allows Manual Horn and Public Address operation WAIL A slower changing tone used on highways YELP A rapidly changing tone used in congested area PHASER A very rapidly changing tone used at intersections or in highly congested areas for maximum attention Phaser may be replaced with HiLo tone or disabled completely See OPTION SWITCHES section MANUAL BUTTON It provides manual control of siren tone rise and fall while in HF or STBY While in WAIL YELP or PHASER pressing MAN button can toggle between see Tones chart It can also be configured to change tone for only 10 or 20 seconds by setting the DIP SW2 4 MAN_T option see OPTION SWITCHES section HORN BUTTON It provides a simulated air horn tone when pressed and overrides all siren tones except Radio The Horn tone may be disabled entirely by setting the DIP SW2 1 HORN_D option see OPTION SWITCHES section PA The noise canceling microphone is used for public address operation It will override any siren mode when the button on the side is pressed The volume can be adjusted using the PA Volume knob Hold the microphone close to your lips for proper operation HRT Input optional The Horn Ring Transfer input may be connected to the horn ring or other switching devices Activating this input will produce Horn tone or other functions depending on Rotary Switch position SAF206S Siren_
17. v 1 sti INSTALLATION It is essential to install the unit properly to ensure safe and reliable operation Please read through all instructions thoroughly and carefully before installing the unit Failure to follow these instructions could result in serious damage to the unit or vehicle and may void warranties The correct mounting and wiring is key to the effectiveness of SAF206S siren Installers must read and follow installation instructions and warnings in the manual from original manufacturer The vehicle operator should verify the siren system is fastened to the vehicle securely and is functioning properly Failure to follow all safety precautions and instructions may cause property damage injury or death WARNING The installer must have good knowledge of electricity vehicle electrical systems and emergency equipment Always seek professional assistance if in doubt CONTENTS Inspect the product contents carefully to see if there is shipping damage or missing content If any damage is found inform carrier immediately Contents should include 1pc Siren unit with attached microphone 1pc Siren mounting bracket 1pc Microphone Clip with mounting screws 1pc 12 Pin Siren Input connector 1pc 2 Pin Light Control Power Input connector 1pc Faceplate button labels 1pc User manual Please contact supplier immediately if any component is missing MOUNTING Mount the unit in an area where it can be easily a
Download Pdf Manuals
Related Search