Home

IAD 161 162_SIP_100

1. This command will clean the configuration stored in the flash and reboot it usr config 75 IAD Gateway User Manual Parameter Usages clean clean all the user defined value and reboot Gateway in factory default mode Note 1 It is recommended to execute flash clean after application firmware been upgraded 2 Only User who login with root can execute it After flash clean all configurations in command ifaddr and pppoe will still be kept For example usr config flash clean Flash clean start Flash clean success I rebooting Attached TCP IP interface to cpm unit O Attaching interface lo0 done HTTPD initialized Flash Check WorkMode PROXY_MODE Start registering to Proxy server AC4804 0 is ok AC4804 1 is ok successful 2 2 Initialize OSS libraries OK VP v1 42 stack open successfully login 76 IAD Gateway User Manual 5 3 12 sysconf This command displays system information and configurations usr config sysconf System information and configuration Usage sysconf print idtime digit bf digit keypad dtmf faxtype typel 2833type type lcdrop ON OFF droptime digit eod digit callerid type service used dtmfstart digits dtmfend digits sysconf print print Display system overall information and configuration idtime Inter Digits time 1 10 sec service Specify gateway service type 0 Dial in service 1 HotLine
2. Re a a EEOEOEOO Re SIF Configuration decente Inerfare Rum Mode 7 Peer Peer E Proxy od Primary Proxy IP Address 10 1 12 Smiem Config erating Secemdaty Proxy IP Address sell PEPaE Configieration ii aa mr Valor Seting Praxy part sosa Ehem Pattern is sugar Function Prefix Firing sell Piane Haak Linel FMhmbers 1001 Dacre mae El Line Acceunt 1001 1 Pasen Linel Password ROM Cunfig uratsin EE SIF paris 060 Flash Cicas RTP Pari 16354 Comuni Daia IF Explre d Run Mode Select IAD to work under Peer to Peer mode or Proxy mode Primary Proxy IP Address Set primary Proxy IP Address or URL address Domain Name Server must be configured Please refer to Network Interface Secondary Proxy IP Address Set secondary Proxy IP Address or URL address Domain Name Server must be configured Please refer to Network Interface When IAD fail to register to primary Proxy it will try to register to secondary Proxy when it fails again it will retry to register to Primary Proxy Outbound Proxy Set IP Address or URL address Domain Name Server must be configured Please refer to Network Configure of outbound Proxy server Proxy port Set Proxy port for IAD to send message default value is 5060 if there is no special request of Proxy server please don t change this value Prefix String set prefix string If user ID cont
3. Sega Interface TA FAR C enable disable FF Info mation Smiem Config eration PEPA Config eration ROM Cong uratsin Flash Cinram Camunia Data 17 38 FAX enable disable FAX function If user wants to fax with IAD gateway this function must be enabled 54 IAD Gateway User Manual 4 3 8 Phone Book Configuration Click Phone Book Configuration in the navigation panel and open the Phone Book Screen De tuerk Interface FF Inlermadien System Configuration EEP AE Config eration Valor Setra Ehem Pattern Nippori Funston Piane Hack DACP Carlie erate EEU EE Passo ii ska H noord India Mira DP fallresa ELGA Dia Prat Pa ROM Config uration i Flash Cinram Abi Daia Delete Dai Add Data User can specify 20 sets of phone book via web interface Please input index Name IP Address and E 164 number of the destination device Delete Date User can delete any configured phone book data by index The following table describes this screen Note The e164 number defined in phone book will be fully sent to destination It is not just a representative number for destination s IP Address In other words user dial this e164 number to reach destination destination will receive the number and find out if it is matched to its line number 55 IAD Gateway User Manual 4 3 9 DSCP Configuration Screen Click DSCP Configuration in the navigation panel and open the DSCP Conf
4. Welcome to JADIS Web Configuration Server Please chek the leme in Jet frame 4 2 Save and Reboot Click OK at the end of every configuration page to confirm your changes All configurations will not take effect before reboot system Please remember to do Commit Data to save all configuration then Reboot System to reboot IAD 44 IAD Gateway User Manual 4 3 Web Management Configuration 4 3 1 Network I nterface Click Network Interface in the navigation panel and open the Network Interface Screen Network Interface bemerk laere LANE Adie Hy w Ma WAN Ake 193 IT ja Ba Dabar Mask BEE ass ET io EEPE Canis urien man ELE Ee Dell reacting geer 192 ia fa sa Pham ate o is PS PAT FF emble rissie tiame isak FETI E emkk E leo BEP Daai wats ENE Server Adler fice fs fie Ma Pirman ma E RIN taigen IF Skarin D palo dinski Heh thay DPP M email F dibi Sammi hei Pieris Server tiee Gi e fis Aao Eicken draer Prima DNS Serer lon PE li A Secaadisy DNI Sener Hor PS ii A LAN IP Address Set LAN IP Address of IAD WAN IP Address Set WAN IP Address of IAD Subnet Mask Set the Subnet Mask of IAD Default routing gateway Set Default routing gateway of IAD Get IP Mode User has to set IAD to use which network mode DHCP When DHCP function enables IAD will automatically search DHCP server after reboot NAT Enable Disable the Network Address Translation function SNTP Ena
5. boot update main boot code optional boot2m update 2M code optional ht updata Hold Tone PCM file optional dsptest update DSP testing code optional dspcore update DSP kernel code optional dspapp update DSP application code optional IP address of TFTP FTP server mandatory file name mandatory method download via TFTP FTP TFTP mode 0 FTP mode 1 ftp specify username and password for FTP server specify EMS Server IP address Note This command can run select one option in app boot dsptest dspcore and dspapp Example rom method 1 rom ftp vwusr vwusr rom app s 192 168 4 101 f app bin 38 IAD Gateway User Manual Parameter Usages print show versions of all rom files app boot boot2m dsptest dspcore dspapp ht To update main Application program code Boot code DSP testing code DSP kernel code or DSP application code and Hold Tone file Note Most of all the Rom file needed to get upgrade is App or Boot2m Please check the exact Rom file before doing download procedure s To specify TFTP server s IP address when upgrading ROM files f To specify the target file name which will replace the old one method To decide using TFTP or FTP as file transfer server 0 stands for TFTP while 1 stands for FTP ftp If users choose FTP in above item it is necessary to specify pre defined username and password when upgrading files server specify EMS Serv
6. root Password voip OK usr config 64 IAD Gateway User Manual 5 3 System Commands Overview 5 3 1 help Press help man will display all command list of IAD The following table lists all of the commands that you can use with the Gateway Refer to the following chapters for descriptions of commonly used commands This user s guide describes commands that are helpful for configuring the Gateway Using commands not documented in the user s guide can damage the unit and possibly render it unusable Commands with IAD Gateway Command DESCRIPTION help Input help man to list all command list duit Input quit exit close to exit telnet connection debug Add debug flag and display debug messages reboot Reboot local machine commit Save all data in IAD ifaddr Internet address manipulation time Show current time ping Test if an IP address is reachable pbook Phone book information and configuration pppoe PPPoE parameters manipulation flash Clean all configuration from flash rom sysconf System information manipulation Sip Configure SIP related parameters security This command is used to configure the account information included username and password obtained from the service provider voice Voice information manipulation support Special functions support manipulation tos Set DSCP values for QOS phone Set
7. sip px 210 68 222 33 linel 12345 In this case is to set proxy IP address as 210 68 222 23 line number as 12345 Step 3 You must configure the accounts using security command 21 IAD Gateway User Manual An example is demonstrated below usr config security line 1 name 12345 password 12345 This is to set username userid as 12345 password as 12345 into line1 which means linel can accept incoming calls after successfully registered to Proxy server Note 1 Please contact with your Proxy vendor to obtain user account information 2 If no need to enter password user also has to set security information please set name the same with line number 2 1 4 3 2 Peer to Peer Mode Peer to Peer Mode allows users to call other VolP devices without the proxy server When in Peer To Peer mode IAD Gateway use Phone Book which will dial predefined phone number and press optional to accelerate the dial as end of dial To configure Peer To Peer Mode in IAD Gateway follow the steps below Step 1 Set Peer To Peer Mode using sip command usr config sip mode O Mode 0 is for Peer To Peer mode while mode 1 is for Proxy mode Step 2 Configure Phone Book using pbook command usr config pbook add name TEST1 ip 10 1 1 1 e164 10 In this case user add one callee record named as TEST1 IP address as 10 1 1 1 and ma
8. 100 Base T IAD Gateway User Manual OPA mua IN A PEN 00000000 NiC mm Ethernet connector LAN WANT e TEL Port RJ 11 connector IAD interface to connect analog phone sets or trunk port of PABX PSTN Port IAD 162 Only RJ 11 connector IAD interface to CO PSTN line or extension port of PABX DC 12V Port DC 12V Power supply IAD Gateway User Manual Part Il Start UP This part explains how to configure essential and basic items before user can run IAD gateway IAD Gateway User Manual 2 1 Software Installation Guide This guide covers all essential configurations under different application user can follow steps below to configure basic items to run IAD gateway 2 1 1 Default Settings of I AD gateway gt WAN IP Parameters 1 WAN P Address 10 1 1 3 Subnet mask 255 0 0 0 e Default gateway 10 1 1 254 2 LAN P Address 192 168 123 123 Subnet mask 255 255 255 0 gt Telnet and Web Login Password Login User Name root Password Null default 2 1 2 Additional Installation Requirements In addition to the contents of your package there are other hardware and software requirements you need before you can install and use your AD Gateway These requirements include 1 A computer with an Ethernet NIC Network Interface Card installed 2 Use Internet Explorer 5 5 or later Netscape Navigator 6 or later versions 3 Analog telephone set Softw
9. 440 125 105 2000 4000 2000 4000 phone bt 620 480 125 105 500 500 500 500 phone dt 440 350 96 96 8000 0 8000 O 88 IAD Gateway User Manual phone flash 400 800 phone level 1 32 usr config Parameter Usages print Print current call progress tone configurations ring ring tone rbt ring back tone bt busy tone dt dial tone This parameter should be accompanied with tone type ring To set RING tone value The played tone type when Gateway is receiving a call rbt To set RingBackTone value The played tone type when Gateway receives a Q 931 Alerting message In condition that Gateway is the originate side bt To set BusyTone value The played tone type when destination is busy dt To set DialTone value The played tone type when hook off a phone set of workable Gateway flash Set the detective flash range in ms for example 300 500 ms Note For tone simulation Gateway adopts dual frequencies as traditional telephone does If users want to have their own call progress tone they can change the value of tones High and Low frequency level cadence can be configured respectively For example usr config phone print rbt Phone ringback tone paramter Ringback Tone frequency high 480 Ringback Tone frequency low 440 Ringback Tone frequency high level 155 Ringback Tone frequency low level 155 Ringback Tone tonel on 2000 Ringback Tone tonel off 4000 Ringback
10. O disable 13 IAD Gateway User Manual 3 PPPoE Click PPPoE Configuration in the navigation panel and open the PPPoE Configuration Screen PPPoE Devece Configuration System i I FAP Information RE Support Func tien Ehanet Bueh Thiscenmnection os DoE DEEP Condiguration DE Device Set PPPoe function to be On or Off User Name Set PPPoE authentication User Name Password Set PPPoE authentication password Reboot After Remote Host Disconnection Enable Disable auto reboot after PPPoE disconnection If user enables this function after PPPoE being disconnected IAD will automatically reboot to re connect and after reboot if IAD still can t get contact with server IAD will keep trying to connect After re connected IAD will also restart system On the other hand if user disables this function IAD won t reboot and keep trying to connect Other items for reference only cannot allow to be configured 14 IAD Gateway User Manual 2 1 3 3 Application mode Proxy Peer to Peer Mode After setting IP address user must assign IAD to work under Proxy mode or Peer to Peer mode If there is no Proxy please set your IAD as Peer to Peer Mode 2 1 3 3 1 Proxy mode Proxy mode means that there will be an intermediate Proxy Server between IAD Gateway and the remote entity While operating at this mode IAD Gateway will
11. Phone Book Target File Type FTP TFTP Server IP Address Set TFTP server IP address Target File name Set file name prepared to upgrade Method Select download method as TFTP or FTP FTP Login Set FTP login name and password Target File Type Select which sector of IAD to upgrade Note 1 After 2mb file download is finished all configurations might change to default values user has to configure again 2 After upgrade Application please remember to execute Flash Clean which will clean all configurations become factory values except IP address 59 IAD Gateway User Manual 4 3 12 Flash Clean Screen Click Flash Clean in the navigation panel and open the Flash Clean Screen omno o ma APS a Gateway will Be revered do factory dafen values Press CLEAN will clean all configurations of IAD and reset to factory default value once execute this function Note User must re configure all commands all over again except Network Configure 60 IAD Gateway User Manual 4 3 13 Commit Configuration Data Screen Click Commit Data in the navigation panel and open the Commit Configuration Data Screen Commit Daia Hill take few secando SIF Information Commit Date to save all configurations Please remember to commit data before reboot your IAD 61 IAD Gateway User Manual 4 3 14 Reboot I AD System screen Click Reboot System in the navigat
12. Tone tone2 on 2000 89 IAD Gateway User Manual Ringback Tone tone2 off usr config usr config phone print rbt Phone ring back tone paramter Ringback Tone frequency high 440 Ringback Tone frequency low 480 Ringback Tone frequency high level 13 Ringback Tone frequency low level 13 Ringback Tone tonel on 100 Ringback Tone tonel off 200 Ringback Tone tone2 on 100 Ringback Tone tone2 off 200 usr config usr config phone print bt Phone busy tone paramter Busy Tone frequency high 620 Busy Tone frequency low 480 Busy Tone frequency high level 155 Busy Tone frequency low level 155 Busy Tone tonel on 500 Busy Tone tonel off 500 Busy Tone tone2 on 500 Busy Tone tone2 off 500 usr config usr config phone print dt Phone dial tone paramter Dial Tone frequency high 440 90 IAD Gateway User Manual Dial Tone frequency low 350 Dial Tone frequency high level 155 Dial Tone frequency low level 155 Dial Tone tonel on 8000 Dial Tone tonel off 0 Dial Tone tone2 on 8000 Dial Tone tone2 off 0 usr config usr config usr config phone print flash Phone flash paramter Flash frequency high 800 Flash frequency low 400 usr config 5 3 19 bureau To set Hotline function must be under Peer to Peer mode and switch to hotlin
13. can be adjustable by manual Vertical type or Horizontal type Environment e Operational Humidity 10 to 90 Non condensing e Operational Temperature O to 40 C e Storage Humidity 10 to 90 Non condensing Storage Temperature 10 to 50 C Front Panel The LEDs on the front panel indicate the operational status of the Gateway IAD 164 dy Welltech power S LAD 162 du Welltech power Siatua POTH FT fi fi Power Green 1 Light on IAD is connected with power adapter correctly and power on IAD Gateway User Manual 2 Light off IAD is not connected with power adapter correctly or not power on e Status Green 1 Light on IAD is under Proxy mode and successfully register to Proxy 2 Light off IAD is under Proxy mode and not successfully register to Proxy or under Peer to Peer mode e TEL Orange 1 Light Blinking IAD IP side has incoming call 2 Light On IAD IP side is in communication 3 Light Off IP Line of IAD is in standby mode eo WAN LAN Green 1 Light on Ethernet port successfully connected with network 2 Blanking Ethernet port is transmitting or receiving data PSTN Orange IAD 162 only 1 Light Blinking IAD IP side has incoming call 2 Light On IAD PSTN side is in communication 3 Light Off PSTN Line of IAD is in standby mode gt Back Panel Ethernet Port Ethernet port is for connecting VolP Gateway to network transmit rate supports 10
14. first register to the Proxy Server located at the ISP side For the following operation it sends the INVITE message to the Proxy Server once you initiate a session Then the Proxy server will forward the INVITE message to the right place And the Response message from the remote entity will be forwarded back to you via Proxy server Step 1 Configure the IAD Gateway SIP Configuration Click SIP Information on the navigation panel In the SIP Information screen select Proxy routed Mode function Step 2 Set the SIP information from your service provider Proxy IP Address Linel Number Linel Account Linel Password and click the OK button Note 1 Please contact with your Proxy vendor to obtain user account information 2 If no need to enter password user also has to set security information please set name the same with line number 15 IAD Gateway User Manual Peer 2 Peer Prog E Config eratinn A ar PEPak Config eration Phere Pare mm Supgont Function an Pone Haih DEEP Cenlig eration poa o 2 1 3 3 2 Peer to Peer Mode Peer to Peer Mode allows users to call other VolP devices without the proxy server When in Peer To Peer mode IAD Gateway use Phone Book which will dial predefined phone number and press optional to accelerate the dial as end of dial To configure Peer To Peer Mode in IAD Gateway follow the steps below Step 1 Configure the IAD Gateway SIP
15. flag open Start to show debug messages close Stop showing debug messages In this example user open debug flags including sip vp msg usr config debug add sip msg usr config debug open For example usr config debug status Current debug type enabled Debug Mode is open DEBUG gt SIP MSG usr config 5 3 4 reboot After commit type reboot to reload Gateway in new configuration The procedure is as below usr config reboot Start to Unregister Unregister complete Rebooting lt will take 40 seconds Attached TCP IP interface to cpm unit O Attaching interface lo0 done HTTPD initialized Flash Check WorkMode PROXY_MODE Start registering to Proxy server AC4804 0 is ok 67 IAD Gateway User Manual AC4804 1 is ok successful 2 2 Initialize OSS libraries OK VP v1 42 stack open sucessfully login 5 3 5 commit Save changes after configuring Gateway usr config commit This may take a few seconds please wait Commit to flash memory ok usr config Note Users shall use commit to save modified value or they will not be activated after system reboot 5 3 6 ifaddr Configure and display Gateway network information usr config ifaddr LAN information and configuration Usage ifaddr print dhcp used sntp mode server ifaddr ip ipaddress mask subnetmask gate defaultgateway ifaddr dns i
16. g7231 g711u g 11a Volume levels voice volume 25 84 IAD Gateway User Manual input gain 25 dtmf volume 23 No sound compress CNG G 729A There is no setting G 723 1 Off G 711 U Law Off G 711 A Law Off Echo canceller On On On On Jitter buffer Min Delay 90 Max Delay 150 usr config 5 3 16 support This command provides some extra functions that might be needed by users usr config support Special Voice function support manipulation Usage support t38 enable busy number noanswer number uncon number support print t38 T 38 FAX enabled disabled busy Busy Forward number if empty please fill null noanswer No Anser Forward number if empty please fill null uncon Unconditional Forward number if empty please fill support t38 1 support busy 1001 support uncon null usr config Parameter Usages print print current settings in support command t38 Enable or disable T 38 fax ability The function is will automatically 85 IAD Gateway User Manual defer codec G 723 or G 729a to T 38 when FAX signal is detected busy Provide setting busy forwrd to other number when you setting this function Then this channel busy auto forward to setting phone number noanswer Provide setting noanser forwrd to other number when you setting this function Then this channel not answer auto forward to setting phone number uncon Provide setting no
17. ifaddr print Internet address information WAN IP address 192 168 13 71 Subnet mask 255 255 248 0 Default gateway 192 168 8 254 NAT enabled OFF 70 IAD Gateway User Manual DHCP startup OFF SNTP mode 1 server 168 95 195 12 time zone GMT 8 cycle 1024 mins IPSharing no PSharing device Primary DNS Server 168 95 1 1 Secondary DNS Server 168 95 1 1 EMS IP Address null EMS User ID vwusr EMS Password vwusr EMS cycle time 0 usr config 5 3 7 time When SNTP function of Gateway is enabled and SNTP server can be found as well type time command to show current network time usr config time Current time is WED SEP 17 12 36 49 2003 usr config 5 3 8 ping Use ping to test whether a specific IP is reachable or not For example if 192 168 1 2 is not existing while 210 63 15 32 exists Users will have the following results usr config ping 192 168 1 2 no answer from 192 168 1 2 usr config ping192 168 1 254 PING 192 168 1 254 56 data bytes 64 bytes from 192 168 1 254 icmp_seq 0 time 5 64 bytes from 192 168 1 254 icmp_seq 1 time 0 64 bytes from 192 168 1 254 icmp_seq 2 time 0 64 bytes from 192 168 1 254 icmp_seq 3 time 0 71 IAD Gateway User Manual 192 168 1 254 PING Statistics 4 packets transmitted 4 packets received 0 packet loss round triP ms min avg max 0 1 5 210 63 15 32 is alive usr config 5 3 9 pbook Phone Book function a
18. information Click SIP information on the navigation panel In the SIP information screen select Peer to Peer Mode function set line number line account and click the OK button Line account must be the same with Line number 16 IAD Gateway User Manual SLIP Configuration Rua Made EF Peer Peer C Proxy Proxy IF Address 10 1 12 xy x Step 2 Configure Phone Book in the IAD Gateway Click Phone Book on the navigation panel In the Phone Book screen enter the Index Name IP address and e164 phone number of the destination and click the Add Data button 17 IAD Gateway User Manual Phane Book 18 IAD Gateway User Manual 2 1 4 Essential Configuration via Telnet Command Line interface This section describes how to setup IAD via Telnet command line interface Please follow procedures below to configure essential items before you use IAD gateway 2 1 4 1 Save Data and Reboot After any configuration has been made user has to save all data and reboot system to make configurations take effect Step 1 Confirm the changed configurations input commit and press enter key to save it Step 2 nput reboot then press enter key to restart Gateway Step 3 After around 40 seconds Gateway will take effect in new configurations Do not turn off your Gateway or remove the Gateway w
19. lanip 192 168 124 124 mask Assigned internet subnet mask gate Assigned IP default gateway 69 IAD Gateway User Manual nat Provide DHCP Server and NAT function dhcp Dynamic Host Configuration 1 ON O OFF dns Setup DNS Server IP Address sntp Simple Network Time Protocol O No update 1 Specify server IP 2 broadcast mode When SNTP function is activated users have to specify a SNTP server as network time source An example is demonstrated below while 10 1 1 1 stands for SNTP server s IP address usr config ifaddr sntp 1 10 1 1 1 timezone set local time zone according to GMT ipsharing To enable or disable IAD behind IP sharing function When this function is enabled user must specify a public fixed IP address usr config ifaddr ipsharing 1 210 11 22 33 Note If the public IP address is not a fixed one IAD cannot work behind NAT with peer to peer mode upnp Enable Disable UPnP function If IP sharing has this function user can enable UPnP function that user doesn t need to configure gateway or IP sharing for NAT function server set EMS server IP EMS is software to help user can easily configure products Please contact with your reseller for more information id specify EMS ID to login EMS Server pwd specify EMS password to login EMS Server emstime specify EMS cycle time For example usr config
20. print voice priority G723 G711U G711A G729 print Display voice codec information and configuration 82 IAD Gateway User Manual Specify sending packet size G 723 30 60 ms G 711U 20 40 60 ms G 711A 20 40 60 ms G 729 20 40 60 80 ms priority Priority preference of installed codecs G 723 6 711U G 711A G 729 volume Specify the following levels voice volume 0 63 default 25 input gain 0 38 default 25 dtmf volume 0 31 default 23 No sound compression and CNG G 723 1 only On 1 Setting of echo canceller On 1 Off 0 per port mindelay Setting of jitter buffer min delay 0 150 default 90 maxdelay Setting of jitter buffer max delay 0 150 default 150 Example voice send g723 60 g711u 60 g711a 60 g729 60 voice volume voice 20 input 32 dtmf 27 voice echo 1111 usr config Parameter Usages print Print current voice information and configurations send To define packet size for each codec 20 40 60 80 ms means to send a voice packet per 20 40 60 80 milliseconds The smaller the packet size the shorter the delay time If network is in good condition smaller sending packet size is recommended In this parameter 20 40 60ms is applicable to G 711u a law 20 40 60ms is applicable to G 729 codec while 30 60ms is applicable to G 723 1 codec priority Codec priority while negotiating with other h323 device This parameter determines the listed sequence in h 245 TCS messa
21. then input new password clean Will clear all password setup and change null Note Gateway Login name only use root or administrator root and administrator have the same authorization except commands that can be excuted by Login name root only passwd set root rom boot room boot2m and flash clean For example usr config passwd set root root1234 Setting login root Password root1234 OK usr config sr config passwd clean Please wait a moment Clean password OK usr config 95
22. 4 3 3 Hotline MOOG a SEED ED EDE GE IE tah mule tate ale ade dtl tales 23 2 1 Special Housing Installation Guide ocooocooccnnconononcnnncnnnnnnnnnos 24 2 1 1 Horizontal Type eo mania ana lada a a dad 24 21 ke ei SS ER EE o ds e Ee 24 RUE RE EE RA RE OE PT 24 RE De AAS MEE AE OER AE A AE OE OE 24 2 1 2 Vertical TYDE sd So se Ee Rd be SR Be GER Ee RA Be ER ed boe tala 25 AE EE MOER AA EA A AI 25 DAD Nba 25 List of Table II Part III Special Applications and Features sssssssssssnnnnnnnnnnnnnnnnn 26 3 1 Behind I P Sharing rias a 27 3 1 1 IP Sharing GohfiduraHOhs is SE EG EER Ee Ed ER Re ED tata 27 3 1 1 1 One IAD Gateway behind IAD ee ee ek ee ee ee ek ee ER ee ER ee ek ee 27 3 1 1 2 More than one IAD behind the same IP Sharing Device 30 3 2 NAT mode PPPOE iii 32 3 3 Call Hold Transfer and Forward ss ss ss sesse asses sesse EER EEN 34 3 3 1 Gall HoldsbressELAS FI wv cats EEN deta EER EE EN De Dene aa eee esa EED 34 3 3 2 Call Transfer press FLASH then transferring number 34 A B13 Gall EOrWard a EE eee ED EG IE DE DE 34 3 4 Upgrade Your AD ie ER SKREE NE SEER EM EKEN WE MEE N Re NE NEK ER ENE EE RENE UR 36 3 4 1 Upgrade via Web management interfaCe esse ee Ee ee ee 36 320 Before Stalts eters de ete wean teed even tn tu cess EE wean saree WEN ea 36 3 4 1 2 Upgrade Version uses enews iii ida ai 36 3 4 2 Upgrade via Telnet Command interface sees see ee ER ee ee 38 3 5 AD 162 PSTN
23. DP prot prefix when your username contains alphabets for example sip1123 then specify the prefix string as sip linel assign line 1 number pbsearch enable disable phone book search function under Proxy Mode If user enabled this function IAD will search dialed number in phone book to see if there is any matched table before send to Proxy server and if there is a matched data in phone book IAD will make call to related IP address expire this parameter is used to inform proxy server the valid duration of the registration information port SIP local UDP port which uses to listen incoming SIP Messages rtp Specify the RTP received port number Note One will need to configure port and rtp parameters only when you deploy two or more sets behind the IP sharing device Router For example usr config sip print Run Mode PEER 2 PEER MODE Prefix string null Linel 1001 80 IAD Gateway User Manual pbook search SIP listen port RTP receive port usr config usr config sip print Run Mode PROXY MODE Primary Proxy address 10 1 1 2 Secondary Proxy address null Proxy port 5060 OutBound Proxy address null Transport Type TCP UDP UDP Prefix string null Linel 1001 Line2 1002 Line3 1003 Line4 1004 pbook search Orr SIP listen port 5060 RTP receive port 16384 Expire 3600 usr config 5 3 14 security This command is used to configure the account inf
24. Features Provide Voice over IP and Fax over IP features SIP RFC 3261 compliance Built in NAT IP sharing function Provided call features Hold forward and transfer Automatic FAX detection Support T 38 protocol Codec G 711 a u law G 723 1 G 729A PPPoE connection VAD Voice Activity Detection CNG Comfort Noise Generate G 168 165 echo cancellation FSK and DTMF Caller ID Provide both IP telephone number and PSTN telephone number in one device for end users IAD 162 only PSTN backup user still can make phone call when external power is failure IAD 162 only Audio feature Codec G 711 a u law G 723 1 6 3kbps G 729A VAD Voice Activity Detection CNG Comfort Noise Generation G 168 165 compliant adaptive echo cancellation Dynamic Jitter Buffer Bad Frame Interpolation Voice DTMF Gain Settings System Monitoring System status WAN LAN TEL Status Power Remote Firmware Upgrade You can use FTP TFTP to perform firmware upgrade for the IAD Gateway from a remote location Security Password protection for system management Built in NAT function Certification CE FCC IAD Gateway User Manual 1 3 Hardware Specifications gt Chassis 190mm W x 110mm D x 51 5mm H e Weight unit 0 3 kg Interface e Four 10 100 Base T Ethernet RJ 45 ports Auto LAN MDI MDIX Input AC 100V 240V Output DC 12V One Two RJ11 Telephone Port IAD 161 162 Special Housing The plastic housing
25. IAD 1611162 USER MANUAL PROTACE ii V Part 1 AD Gateway OvVervieW c comccocconnconccnncnnncnncnnnennnnnnenananncnnnenanana 1 ao Ed AR RE ias 2 1 2 Software Specifltations N as 3 1 3 Hardware Specifications iss asses n N GEN GESE ENE SES AE EG SEE N Eg RE EEN De Eg 4 Part ll Start UP o nee een errr Cre ree cere or os ee ee 7 2 1 Software Installation Guide cooccconcnconncononconancnnnarnnnnananrannananass 8 2 1 1 Default Settings of IAD gateway iss es see es ee ee Re ee ed Re ee ee 8 2 1 2 Additional Installation Requirements ee see ke ee Re RR ee ER ee ee 8 2 1 3 Essential Configuration via Web Management interface 10 2 1 3 1 Save Data and RebOOE WERE E REEN EE DE EN Ee ee GE ED 10 2 1 8 2 Setup NELWOLK DEE AS oi 12 T Fixed Pike sies SR Se ER Ge SR Ee se Ee ER ee SR bo BED 12 A REED ED OD DER a eS ek les 13 SIPPROE alo 14 2 1 3 3 Application mode Proxy Peer to Peer Mode esse ske 15 Di Vid A MOJE oe A 15 2 1 3 3 2 Peer to Peer Mode see ee RR ER ed Re ee RR Re Re 16 2 1 4 Essential Configuration via Telnet Command Line interface 19 2 1 4 1 Save Data and Reboot re tale e ee Ee SE ev 19 2 1 4 2 Setup Network sis ske ad aa 19 A Et EE ee OE A 19 DEEP ES RE Ge GE A 19 3 PPPOE od ce ce ee Cand er dle Cyne ee eke ee N A Ce EE here EN EE 19 2 1 4 3 Application mode Proxy Peer to Peer Mode esse esse 21 2 1 4 3 1 AO 21 2 1 4 3 2 Peer to Peer Mode uso 22 2 1
26. Line Application iss RR R EER KREER KEER RE ER RE EER KAREE 41 B25 PSTN EAN o ea E EOE connector nee 41 3 5 1 1 Make PSTN call from TEL Phone set iss ee sesse ee ee see ee ee 41 3 5 1 2 PSTN A o no nes 41 3 5 2 PSTN Incoming Ella ie 41 3 5 21 VOlP TEL iS BUSY esas 41 3 5 2 2 VolP TEL is IVA AD A AA ee 41 3 5 3 VolP Outgoing Call ses reto ER ES EE ER ERA ES atera RR BEN SE 41 3 5 4 VolP Incoming Call os id aad 41 Part I V Web Management I nterface cccononocconnconnnnnconnnnncnnnenanenananos 42 4 1 Login and welcome SCreen sssssssssssss55555555 uuuuunnnnnnnnnnnnnnnnnn 43 4 2 Save and ReboOt ss RR EER ER KERE ER KERE ER KERE EER KERE EER KERE EER KERE EREE 44 4 3 Web Management ConfiguratiON conccocccnncononnncnnncnannnncannnnnnnas 45 4 31 Network lnterface iii 45 43 2 SIP Information SCFESN MERE Ee DR EA N ae AA 47 4 3 3 System Configuration cn a di 49 4 3 4 PPPoE Configuration Screen ee see es ee ee ee ee ee ek ee ek ee ee ee ek ee 50 4 3 5 Voice Configuration Screen cs 51 4 3 6 Phone Configuration Screen ee see Re ER EA Re Re Re ee Re AE 52 List of Table III 4 3 7 Support Configuration SCreeN see EE ER EE EE ER RR ee ER Re ee ee Re ee 54 4 3 8 Phone Book ConfiguratiON esse es ee ek ee ER ee ER ee ER ee ek ee ER ee ek ee 55 4 3 9 DSCP Configuration Screen ee see se ee ER ee Re Re ee RR ee Re eg 56 4 3 10 Password Configuration SCreeN see sk ee Re RR ee ER ee ER ee ek
27. Precedence Class 1 Class 2 Class 3 Class 4 Low Drop Precedence AF 11 AF21 AF31 AF 41 001010 010010 011010 100010 Medium Drop Precedence AF12 AF22 AF32 AF42 001100 010100 011100 100100 High Drop Precedence AF13 AF23 AF33 AF43 001110 010110 011110 100110 Please refer to RFC standard documents for more information about what is DSCP 57 IAD Gateway User Manual 4 3 10 Password Configuration Screen Click Password configuration in the navigation panel to open the Password Configuration screen It is highly recommended that you change the default password Null Current Paeswer Mew Passar SIF Inlermadien oe mar MEA Svetem Cenfigerstion Confirm New Pasrwerd PEPE anig mation Valor Seti f CHANGE ABORT dae see ee Ehem Pare rm Skpgon Fun tien Phone Hack DACP Esrliguerddon luna ROM Confizura an Flash Ciria D Change First select login name as root or administrator then enter current password new password and confirm new password again to set new password Abort Press abort will clean all inputs 58 IAD Gateway User Manual 4 3 11 ROM Configuration Screen Click ROM Upgrade in the navigation panel and open the ROM Configuration Screen ROM Configuration FIP TFTP server P Address 4 _ EZ ee sea Ps FTP ago nael pm Apekcanca ma Sippari Fun tian OE
28. Pv4 address or dns name px2 Secondary Proxy server address IPv4 address or dns name pxport Proxy server port the port of proxy outpx OutBound Proxy server address IPv4 address or dns name transport SIP message transport type TCP 0 UDP 1 prefix Specify prefix string use it when Userl D contains alphabets if UserlD uses numerals specify as null linel TEL1 Phone number pbsearch Search phone book O off 1 on expire The relative time after which the message expires 0 2731 1 port SIP local UDP port number 5060 5070 Default 5060 rtp RTP port number 2326 65534 Default 16384 Example sip mode 1 Sip px 210 59 163 171 linel 70 line2 71 line3 72 line4 73 79 IAD Gateway User Manual usr config Parameter Usages mode Configure as Proxy mode or Peer to Peer mode 0 Peer to Peer mode 1 Proxy mode px to specify Proxy address when IAD Gateway is in proxy mode Proxy address can be IPv4 address or DNS name px2 to setting Secondary Proxy server address Proxy address can be IPv4 address or DNS name Proxy port Set Proxy port for IAD to send message default value is 5060 if there is no special request of Proxy server please don t change this value Outbound Proxy Set IP Address or URL address Domain Name Server must be configured Please refer to Network Configure of outbound Proxy server transport Provide setting SIP message transport type for TCP or U
29. ROM Canis uraan IP Sharing Server Address 210 se fia fiss 1 Flash Clean Primary DNS Serer ict ps MM Comuni Data Secsmdary DNS Seme fice ps ff ar oe Rebsor Fries 28 IAD Gateway User Manual Step 8 Click Commit Data on the navigation panel In the Commit Configuration Data screen click the Commit button In the Commit Configuration Data screen will Display Commit to Flash OK when IAD finished committing data Step 9 Click Reboot System on the navigation panel In the VolP Gateway screen click the Reboot button It will take around 40 seconds to reboot Step 10 Close the current browser windows and launch your web browser again Enter the new IP address in the Location or Address field 29 IAD Gateway User Manual 3 1 1 2 More than one IAD behind the same IP Sharing Device 1 Assign an IP address to each IAD using fixed address 2 Enable the IP Sharing function for each set using following command Fixed IP Address usr config ifaddr ipsharing 1 public IP of IP Sharing 3 Configure separate SIP port and RTP port for each set to prevent from port conflict For example if set A uses the default settings SIP port 5060 RTP port 16384 you must change set B s setting to SIP port equal to 5061 and RTP port equal to 26384 for instance Change SIP port usr config sip port 5061 Change RTP port usr config sip rtp 26384 4 Use the Port Forwarding or Port Redirection function prov
30. Rom file before doing download procedure s To specify TFTP server s IP address when upgrading ROM files f To specify the target file name which will replace the old one method To decide using TFTP or FTP as file transfer server 0 stands for TFTP while 1 stands for FTP ftp If users choose FTP in above item it is necessary to specify pre defined username and password when upgrading files server specify EMS Server IP address Provide auto upgrade rom application verion but you must use EMS Server it work For example usr config rom print Download Method TFTP Boot Rom sdboot 200 Application Rom lasiplAD 107 DSP App 48302ce3 140 DSP Kernel 48302ck 140 DSP Test Code 483cbit bin Hold Tone holdtone 101 usr config 5 3 21 passwd For security concern users have to input the password before entering configuration mode passwd command is for password setting purpose usr config passwd Password setting information and configuration Usage passwd set Login name Password clean passwd set Loginname Password 94 IAD Gateway User Manual clean Clear all password stored in flash Note 1 Loginname can be only root or administrator 2 passwd clean will clear all passwd stored in flash please use it with care Example passwd set root Your Passwd Setting passwd clean usr config Parameter Usages set Set login name and password input login name
31. System on the navigation panel In the IAD Gateway screen click the Reboot button It will take around 40 seconds to reboot Reboot LILADIGI Gateway Iewill take 40 peramds do reboot remember da COMMIT data bedaar reba _REROOT Supponi Fune tien Phone Hack DACP Step 3 Close the current browser windows and launch your web browser again 11 IAD Gateway User Manual 2 1 3 2 Setup Network 1 Fixed IP To configure the VoIP Gateway IP address please click Network Interface on the navigation panel In the Network Interface screen type a new IP address subnet mask and the default routing gateway e g IP Address 192 168 13 80 Subnet mask 255 255 248 0 Default routing gateway 192 168 8 254 and click the OK button Metmork Interface oa al aa DHCP enable F disable SNIP enable 7 disable SNIP Server Address ie fos ios iz o IP Sharing enable disable UPmP enshle F disable I Sharing Serper Address 210 fa fies fise Primary DNS Serve fie ps ft Secomdasy DNS Server laa BE EE ox 12 IAD Gateway User Manual 2 DHCP Click Network Interface on the navigation panel In the Network Interface screen enable the DHCP function if you are using the cable modem or DHCP server and click the OK button Riebwork Interiace Address fio fiee fps o Seras pass casa R cad dlls fe jc Sti ees EE DHCP Le F disable SMTP enable
32. ains alphabets user can set it as prefix string here For example if Account Name is 123 IAD will sent out messages as Account Name IP address of Proxy if user set prefix as abc IAD will set out as abc123 IP address of Proxy This function is for special proxy server 47 IAD Gateway User Manual Line Number identify one number for the IAD to register to the Proxy Line Account set user name of IAD for registering User can set user name and password for registering If password is no need please set user name the same as line number or IAD won t register successfully Line Password set password for registering SIP Port set SIP UDP port RTP Port set RTP port for sending voice data Expire set expire time of registration IAD will keep re registering to proxy server before expire timed out 48 IAD Gateway User Manual 4 3 3 System Configuration Click System Configuration in the navigation panel and open the System Configuration Screen ores system Lonfiguralion eter Interface Keypad DOM Tree inHand RECIBA RAP Info sers tien RFCI833 Payload Type 96 Sao ed el alka FAX Payboad Type LDI PEPA len inter Digit Time E Wailer Setting Caller Type F diable C FSRRELLCOORE O DTMF Phare Fair Busy Forwards 07 DEF Huppari Fane tag SEEN Phone Bock Esd af Dial Dies ONE OT fa r Son OK ROM Config uraian Elash Clean mm Dats ehant Treier Ke
33. anser forwrd to other number when you setting this function Then all call this channel number will all auto forward to setting phone number Note It is not recommended to change the value in this command only if users do know well the application This might cause incompatibility with other devices For example usr config support print Special Voice function support manipulation T 38 FAX support Disabled Forward Numbers Busy Forward number 0123456789 NoAnswer Forward number 0212345678 Uncondition Forward number usr config 5 3 17 tos This command is for setting Differentiated Service Code Point configuration usr config tos IP Packet ToS type of Service Differentiated Service configuration Usage tos rtptype dscp tos sigtype dscp tos print 86 IAD Gateway User Manual rtpreliab mode tos print Example tos rtptype 7 sigtype O usr config Parameter Usages rtptype the packages of voice 0 63 sigtype the package of call signal 0 63 Note The value of rtptype and sigtype is from O to 63 It s working if it supported by your network For example usr config tos print IP Packet ToS information Signalling Packet DSCP Code 0 Media Packet DSCP Code 0 usr config 5 3 18 phone Gateway progress tone is configurable Default tone value is set according to U S tone specification Users may adjust the values according
34. ansfer the DTMF in if users disable the end of dial function Users have to press the keypad in if the end of dial function is enable Note User can also define IP address here in P2P mode once user press Gateway will call out this IP address callerid Support Bell Core and DTMF callerlD function After the first ring at destination site device will send line number as callerlD to called site dtmfstart DTMF Caller D Start Symbol dtmfstart DTMF Caller D End Symbol For example usr config sysconf print System information Gateway Service Inter Digits time BusyForward OFF Keypad DTMF type In band End of Dial Digit Caller ID Type EN DTMF Caller ID Start Symbol D DTMF Caller ID End Symbol C 78 IAD Gateway User Manual RFC2833 Payload Type 96 FAX Payload Type 101 Disconnect Supervision OFF Loop Current Drop Time ms 500 usr config 5 3 13 sip This command is to configure SIP related parameters usr config sip SIP stack information and configuration Usage sip print mode pxmode outpx Paddmress sip px address px2 address domain domain prefix prefixstring linel number line2 number line3 number line4 number expire t1 port udpPort rtp rtpPort sip print print Display SIP stack information and configuration mode Configure as Proxy mode 0 Peer to Peer mode 1 Gateway mode 2 px Primary Proxy server address I
35. are tools SIP Proxy Server optional 5 Installation Wizard optional This is a configuration tool for users can easy access products and configuring IP address Please contact with your retailer for more information D IAD Gateway User Manual Please follow steps below to access IAD configuration interface Step 1 Connect WAN Port of I AD Gateway to public network Connect the WAN port silver on the IAD Gateway to the Ethernet port of your network e g Cable Modem ADSL Modem using the standard CAT 5 straight Ethernet cable Step 2 Connect your PC to the LAN port of I AD Connect your PC to the LAN port of IAD with standard CAT 5 straight Ethernet cable Step 3 Set your PC as DHCP mode Please go to the network setting of your PC and set it as DHCP mode let your PC can automatically search for DHCP server and get one valid IP address IAD has embedded DHCP server default is enabled so that your PC will get one IP address from IAD DHCP server Step 4 Open your browser and input I P address 192 168 123 123 Once your PC has got an IP from IAD you may connect IAD via WEB browser to do more configurations The default LAN IP address of IAD is 192 168 123 123 please input this IP address on web browser to connect with web management interface Please refer to Part III Web management for more information Step 5 Advanced Setting via Telnet Optional If user wants to do more advanced and complete settings that cannot be found
36. ble Disable the Simple Network Time Protocol function SNTP Server Address Set SNTP Server Address When SNTP server is available enable IAD SNTP function to point to SNTP server IP address so that IAD can get correct current time GMT Set time zone for SNTP Server time User can set different time zone according to the location of IAD For example in Taiwan the time zone should be set as 8 which means GMT 8 45 IAD Gateway User Manual IP Sharing Enable it if IAD is behind IP Sharing router UPnP Enable it if IP sharing or NAT device supports UPnP function so that no need to configure IP sharing or IAD when IAD is behind NAT device IP Sharing Server Address Set Public IP Address of IP Sharing router for IAD to work behind IP sharing Primary DNS Server Set Primary Domain Name Server IP address User can set Domain Name Server IP address Once IAD can connect with DNS server user can specify URL address instead of IP address for Proxy and phone book IP address Secondary DNS Server Set Secondary Domain Name Server IP address Note When IAD is behind IP sharing device if Proxy support behind NAT function both IAD and IP sharing don t need to do any configuration Please contact with your proxy vendor more correct information before configuring IAD 46 IAD Gateway User Manual 4 3 2 SIP Information Screen Click SIP Configuration in the navigation panel and open the SIP Information Screen ee
37. d No 2 Deactivate 76 3 3 3 2 No response Answer While no one answers the call incoming call will be forwarded to the assigned number 1 Activate 75 Forward No 2 Deactivate 75 3 3 3 3 Unconditional Incoming call will be forwarded to the assigned number unconditionally 1 Activate 77 Forward No 2 Deactivate 77 35 IAD Gateway User Manual 3 4 Upgrade Your IAD 3 4 1 Upgrade via Web management interface 3 4 1 1 Before start Step 1 Please confirm Host PC which is installed as TFTP FTP server and is in available network Step 2 Note down your current configurations such as SIP Information Phone Book 3 4 1 2 Upgrade Version Step 1 To update the IAD Gateway ROM Version please click ROM Upgrade on the navigation panel In the ROM Configuration screen type TFTP FTP Server IP address Target File Name Method Target File Type e g Server IP Address 192 168 4 71 Target File Name 4alAD 204 Method TFTP Target File Type Application image and click the OK button Me ear Interface FTP TRIP server IF Address MIF Inlermadien Target File iame System Config eratinn Meihed PEPE Config ersiinn here Pare rm FTF Login Target File Type Sepgent Function Paar Book DEEP Carlie eration Passed ROM Cong uratean Flash Cinram Camumia Daia 36 IAD Gateway User Manual Step 2 After upgrade finished on scr
38. e mode usr config bureau Bureau line setting information and configuration Usage bureau hotline Port DestlP TELnum bureau print print Display Bureau line information and configuration hotline Set Hot line information Port range 1 6 Note Hotline feature should be used together with sysconf service 1 HotLine service sip mode O peer to peer mode Example bureau hotline 1 192 168 4 69 628 2 192 168 4 200 999 91 IAD Gateway User Manual usr config Parameter Usages print Display current Hotline table hotline Define Linel and Line2 s Hotline table respectively The table is included Line number destination IP Address and destination Port or Number For example 1 Destination is a IAD device 628 is its Linel number usr config bureau hotline 1 200 168 4 69 628 User picks up the Linel and then hears the ringback tone generated from destination Of course 628 are ringing simultaneously 2 Destination is a FXO device Port 3 is the one connected to PSTN Line usr config bureau hotline 1 200 168 4 69 82265699 User picks up the Linel and then hears the ring back tone generated from destination Simultaneously 82265699 numbers is the destination which is dialed from Port 3 Above FXO example is subject to the FXO configurations such as 2nd dial ON or OFF For example usr config bureau print Bureau line setting relate information Hot lin
39. e table Destination Address Remote TEL 92 IAD Gateway User Manual 5 3 20 rom ROM file information and firmware upgrade function usr config rom ROM files updating commands Usage rom print app boot dsptest dspcore dspapp ht method used boot2m S TFTP FTP server ip f filename rom print print show versions of rom files optional app update main application code optional boot update main boot code optional boot2m update 2M code optional ht updata Hold Tone PCM file optional dsptest update DSP testing code optional dspcore update DSP kernel code optional dspapp update DSP application code optional IP address of TFTP FTP server mandatory file name mandatory method download via TFTP FTP TFTP mode 0 FTP mode 1 ftp specify username and password for FTP server specify EMS Server IP address Note This command can run select one option in app boot dsptest dspcore and dspapp Example rom method 1 rom ftp vwusr vwusr rom app s 192 168 4 101 f app bin usr config Parameter Usages print show versions of all rom files app boot boot2m dsptest dspcore dspapp ht To update main Application program code Boot code DSP testing code DSP kernel code 93 IAD Gateway User Manual or DSP application code and Hold Tone file Note Most of all the Rom file needed to get upgrade is App or Boot2m Please check the exactly
40. ee 58 4 3 11 ROM Configuration Screen EE SE EER conn WENE KEN WEEREENS DEER EYE LE EE 59 4 3 12 Flash Clean CON ee dia 60 4 3 13 Commit Configuration Data Screen ee ik ee renee renee ER ee ee 61 4 3 14 Reboot IAD System SCreeN ee see see Ee EA ee Re RR Re ee ee Ee 62 Part V Telnet Command Interface iss K REK KREER KAR RR RARR RE ER RE EER KEER 63 511 ad EE ee ae ae ke EN Re ee Ee 64 5 2 Save and Rebollo 64 5 3 System Commands OvervieW issues ER RE EK REK KARRE AR KARRE EER A ERA RR nn 65 A SE DE AA Ee ee Ge GE 65 A ie EE AE HO EE T DE 66 5 2 3 Fdebug RE EE GE De Ge EE aaa 66 BA EL E MR aE MRE TART MC OR EMR TAR TMT AR ER TR MR OR AE 67 Prae Fe GOL UNC Ves tar ee nents dia deter dia debera dias debeis dnd 68 A GE ee ana ae ee GE eee ee 68 A ere 71 A r a a r a DES 71 Nc A ODO AAA A AAA EEE E 72 A RT OR OE OR ER OR RR RE 7a Bes el las Lie ads 75 A ES is ASE LEES E AA 71 BS SSID ey utes ES ie ta eit Seat ents ae a wien Gx EER aa ve N hea sens De Di ER eN ER ee 79 NA A ee ee eg eo DE 81 O Voices e Ke 82 5 5 16 SUpport va ds 85 A AA A A ED A DE De GE 86 A AAA ANN Ede MM Re in ed HA Re 87 EN EE De ies Oot A ah eke 91 Da OTOM is NE EE OS O RE sae 93 e AA ll AAA O AO 94 List of Table IV Preface gt About this User s Manual This user s guide includes specifications installation guide web management and command line configuration interface for the IAD 161 162 VolP Gateway gt Revision History Vers
41. een will display Please issue FLASH CLEAN to consist software version information Phasa ima FLASH CLEAN io cons solhas varrim Meimei erior AEP aiiin My rin DON AA Fpjie eri Piume Pailera geet Pe ige Elsie Prik DECT Candi garw iny Vat ed E aS eT arii Eladi Clean Tomnii Nsa feboal Hidrin Aereo miera Step 3 Click Flash Clean on the navigation panel In the Flash Clean screen click the CLEAN button Flash Cla t LAFNN abras il be aA fo ory efi ara EP da irni Spririn CLEAN A AT Spice Beitia Pane Pribero Apo a Lio Fleur Book id grater Eur ad ECH Cantigi wiin Elh ET Correos Tara Beba Siirin Step 4 In the Flash Clean screen to Display Flash cleaned Please reboot your system when Flash Clean Ok 37 IAD Gateway User Manual Step 5 Click Reboot System on the navigation panel In the Reboot IAD Gateway screen click the Reboot button It will take 40 seconds to reboot Step 6 Close the current browser windows and launch your web browser again Enter the IP address in the Location or Address field 3 4 2 Upgrade via Telnet Command interface Use rom command to upgrade software of IAD usr config rom ROM files updating commands Usage rom print app boot dsptest dspcore dspapp ht method used boot2m S TFTP FTP server ip f filename rom print print show versions of rom files optional app update main application code optional
42. ency on time off time voltage level IAD will give ring to phone set to trigger ring If user found that phone set cannot ring when having incoming call please try to increase ring frequency here ringing frequency 15 100 Unit Hz ringing ring ON OFF O 8000 Unit ms ringing level 0 94 Unit V tone frequency 0 65535 Unit Hz tone freqLevel 0 65535 Unit mVrms tone Tone ON OFF O 8000 Unit ms VV VV V Y Ring Back Tone Set ring back tone parameters Busy Tone Set busy tone parameters Dial tone Set Dial tone parameters 52 IAD Gateway User Manual Low frq Frequency value of Low frequency High frq Frequency value of High frequency Low lev Level volume of Low frequency High lev Level volume of High frequency Oni On cadence of first cycle Off1 Off cadence of first cycle On2 On cadence of second cycle Off2 Off cadence of second cycle VVVVVV VV Note 1 If disconnect tone is single frequency user has to configure the same frequency value of Low frequency and High frequency the same level of Low frequency and High frequency 2 For On Off cadence user must set 1023 instead of 0 if there is only one set of cycle please as in second set columns 53 IAD Gateway User Manual 4 3 7 Support Configuration Screen Click Support configuration in the navigation panel and open the Support Configuration Screen
43. er IP address Provide auto upgrade rom application verion but you must use EMS Server it work For example usr config rom print Download Method TFTP Boot Rom sdboot 200 Application Rom lasiplAD 107 DSP App 48302ce3 140 DSP Kernel 48302ck 140 DSP Test Code 483cbit bin Hold Tone holdtone 101 usr config 39 IAD Gateway User Manual After software like application has been upgraded please execute flash clean to clear old configurations and make upgrade complete This will keep all configurations under ifaddr usr config flash clean 40 IAD Gateway User Manual 3 5 LAD 162 PSTN Line Application 3 5 1 PSTN Outgoing Call 3 5 1 1 Make PSTN call from TEL Phone set Default TEL line is intended to make IP call if user wants to make a call via PSTN line please dial then user will hear dial tone from PSTN side If the PSTN port doesn t connect a PSTN line press the signal will be back to IP side then play busy tone 3 5 1 2 PSTN Backup If IAD is working under Proxy mode and fail to register to Proxy server TEL line will automatically switch relay to PSTN line which means when VolP system is failed user can still make a call from PSTN line without pressing Uk 3 5 2 PSTN Incoming Call 3 5 2 1 VoIP TEL is busy Caller from PSTN side can still make a call to IAD PSTN LED will be blanking when user hangs up IP call TEL phone set wil
44. evice Enabled Status Ready User name 84460791 hinet net Password PEREA Reboot Yes IP address 218 160 239 35 Destination 61 223 128 254 DNS primary 168 95 1 1 Subnet Mask E 299 255 299 209 Authenticate PAP 20 IAD Gateway User Manual Protocol TCP IP Device PPP PPPoE usr config 2 1 4 3 Application mode Proxy Peer to Peer Mode After setting IP address user must assign IAD to work under Proxy mode or Peer to Peer mode If there is no Proxy please set your IAD as Peer to Peer Mode 2 1 4 3 1 Proxy mode Proxy mode means that there will be an intermediate Proxy Server between IAD Gateway and the remote entity While operating at this mode IAD Gateway will first register to the Proxy Server located at the ISP side For the following operation it sends the INVITE message to the Proxy Server once you initiate a session Then the Proxy server will forward the INVITE message to the right place And the Response message from the remote entity will be forwarded back to you via Proxy server Step 1 Set Proxy Mode using sip command usr config sip mode 1 Mode 0 is for Peer To Peer mode while mode 1 is for Proxy mode Step 2 You must specify Proxy address obtained from your service provider And the Proxy address can be Pv4 address as well as DNS name Several important SIP parameters are listed below when setting proxy mode px linel For example usr config
45. fferent packet size for each codec G 723 Silence Suppression Enable Disable sound compression and comfort noise generation It is only for codec G 723 1 Volume Adjust the volume in Voice sending out Input receiving DTMF DTMF sending out Echo Cancelor Enable Disable suggested always Enable this function Jitter Buffer Set Min Delay and Max Delay of Jitter Buffer for voice packets Note Well the application before you change voice parameters because this might cause incompatibility 51 IAD Gateway User Manual 4 3 6 Phone Configuration Screen Click Phone Configuration in the navigation panel and open the Phone Configuration Screen For tone simulation IAD Gateway adopts dual frequencies as traditional telephone does If users want to have their own call progress tone they can change the value of tones ee Ne rerk Ineerfare on Ring Tame Frenquenes 20 Eno cor soon SIF Infiermatinn A Eysrem _ Higie Lotto Higher Lawley Om OE ie seer anale TO aan iss iss on FT Pak A Baar Timet Hed ler He Lem On on z 630 HET ES MES i ann Lowry ler Lomler n of Ehem Patiern Dial Tam q jaa iss i oo ard F ien A o Migu Led Higher Leer Op ow Phone Book ed Did FT fea i e e EI i DEEP F Config eration ERS ese REIS ee ars Password ROM Configura Flash Cinram Combi Daia ar Es Ring Tone Set Ring frequ
46. ge The codec listed in left side has the highest priority when both parties determining final codec User can also select the particular codec without 83 IAD Gateway User Manual others usr config voice priority g723 only select this codec usr config voice priority g723 g729 g711u g711a select four codecs and g723 is the first choice volume There are three adjustable value voice volume stands for volume which can be heard from Gateway side range 0 63 default 28 input gain stands for volume which the opposite party hears range 0 38 default 28 dtmf volume stands for DTMF volume level which sends to its own Line range 0 31 default 23 nscng Silence suppression and comfort noise generation setting 1 ON O OFF It is applicable to G 723 codec only usr config voice nscng g723 1 echo On or Off the activate each canceler mindelay The minimum jitter buffer size Default value 90 ms maxdelay The minimum jitter buffer size Default value 150 ms usr config voice mindelay 90 maxdelay 150 Note Be sure to know well the application before you change voice parameters because this might cause incompatibility For example usr config voice print Voice codec setting relate information Sending packet size G 729A 40 ms G 723 1 60 ms 6 7110 40 ms G 711A 40 ms Priority order codec g729a
47. hile saving your configuration 2 1 4 2 Setup Network Use command ifaddr to configure Gateway IP Address and related information 1 Fixed IP usr config ifaddr ip 192 168 1 11 mask 255 2555 255 0 gate 192 168 1 254 In this case is to configure Gateway IP Address as 192 168 1 11 subnet mask as 255 255 255 0 default router gateway as 192 168 1 254 2 DHCP usr config ifaddr dhcp 1 In this case is to enable DHCP mode of IAD once IAD reboot system it will automatically capture IP from DHCP server 3 PPPoE Step 1 To Set PPPoE mode please use pppoe command usr config pppoe dve 1 PPPoE used usr config pppoe open PPPoE open 19 IAD Gateway User Manual Step 2 nput the user id amp password provided by your ISP usr config pppoe id 123 hinet net PPPoE login account usr config pppoe pwd 123 PPPoE login Passowd For example usr config pppoe print PPPoE adapter information Device Status User name Password Reboot Enabled Not initialized 84460791 hinet net KKK K k KK Yes usr config Step 4 Commit and reboot IAD usr config commit usr config reboot Step 5 When IAD successfully establish PPPoE connection use command pppoe print to see detail information For example usr config pppoe print PPPoE adapter information D
48. ided by IP Sharing device Router See following for example gt Advanced setting gt NAT setting gt Port Redirection Active Configuration Actual Items Service name Protocol Puri Virtual IP Virtual Port Enable or UDP UDP UDP 26394 192 168 1 11 26394 30 IAD Gateway User Manual Note With Dynamic WAN IP Address when the WAN IP is changed we need to change the external IP of IAD Gateway using above command 1 Different Vendor s Router will have different appearance of setting 2 Once you set the DMZ Host you don t need to configure the Port Forwarding and vice versa 3 If there is only one IAD Gateway attached to the IP Sharing device it is recommended to use DMZ Host setting to enable the NAT traverse and disable the Port Forwarding 4 If there are two or more sets of IAD Gateway attached to the IP Sharing device please configure the Port Redirection Forwarding to enable the NAT traverse and disable the DMZ Host 5 After the IP Sharing configuration of IAD Gateway and IP Sharing device is complete you must reboot the IAD Gateway to activate the new settings ad IAD Gateway User Manual 3 2 NAT mode PPPoE Step 1 Set PPPoE mode using pppoe input the user id amp password provided by your ISP using pppoe reboot the device after disconnection using pppoe usr config pppoe dve 1 PPPoE used usr config pppoe open PPPoE open usr conf
49. ig pppoe id 123 hinet net PPPoE login account usr config pppoe pwd 123 PPPoE login Passowd usr config pppoe reboot 1 Enable Step 2 Set NAT function usr config ifaddr nat 1 For example usr config ifaddr print Internet address information LAN IP address 192 168 123 123 WAN IP address 192 168 13 71 Subnet mask 255 255 248 0 Default gateway 192 168 8 254 NAT enabled ON DHCP startup OFF SNTP mode 1 server 168 95 195 12 time zone GMT 8 cycle 1024 mins IPSharing no PSharing device Primary DNS Server 168 95 1 1 Secondary DNS Server 168 95 1 1 usr config 32 IAD Gateway User Manual Step 5 When Gateway connection succeed Setup PC use LAN IP connection Network Select Specify an IP Address and enter 192 168 123 111 in the IP Address location where xxx is a number between 2 and 254 used by the VolP Gateway to identify each computer and the default Subnet Mask 255 255 255 0 Please notice that two computers on the same LAN cannot have the same IP address Set Default Gateway value as 192 168 123 123 in the new gateway field Then save your change PC can also use DHCP mode when DHCP server of IAD is enabled 002 IAD Gateway User Manual 3 3 Call Hold Transfer and Forward Gateway provides call features including call hold transfer and forward Please be noted that both calling and called site have to support this featu
50. iguration Screen Mier Code Point DiSCEH Configuration fetwork Interface Siemal Packet FIF Inlermatien T Amire Farwarding AF FHE Delay Prisrtiy Chus 1 Diap Precedence Low e Smiem pe Configuration Exqe ited Forwarding EF PHE EEPE Config eration E Dean Valor Setting C teer Assign Special DGCP Code e RIF Packet Sipponi Function gede C Ascured Forwarding AF PHE Delar Priority ES 1e Drop Precedence ete Expedited Ferwanting EF PHE Condition Password Default ROM Cong ura an C User Assign Special DSCP Code Flash Clean Damme Daia Set Signal or RTP Packet DSCP value Assured Forwarding AF PHB Select Delay priority and Drop Precedence Expedited Forwarding EF PHB Select TOS value as EF Default Select TOS value as 0 User Assign Special DSCP Code User can set other unspecified value here TOS DiffServ DS priority function can discriminate the Differentiated Service Code Point DSCP of the DS field in the IP packet header and map each Code Point to a corresponding egress traffic priority As per the definition in RFC2474 the DS field is Type of Service TOS octet in IPv4 The recommended DiffServ Code Point is defined in RFC2597 to classify the traffic into different service classes The mapping of Code Point value of DS field to egress traffic priorities is shown as follows 56 IAD Gateway User Manual DROP
51. ion Date___ Author Modified Contents Sep 17 2004 Sabrina 1 Revision for IAD 161 162 SIP Gateway List of Table V IAD Gateway User Manual Part IAD Gateway Overview This part introduces the software hardware specifications and default settings of the IAD Gateway IAD Gateway User Manual 1 1 Overview The IAD 161 is a one port telephone extension and three ports SOHO Router to IP network gateway It provides Data transfer by 10 100Mbps telephone services and T 38 fax over IP network with easily operation and configuration It is most suitable for SOHO and small to medium enterprise in Internet communication environment The IAD 161 provides IP telephone number for end users with FreeTalk voice service User can make phone call via Internet now No more long distance and international telephony fee It also connects three computers without another IP sharing as showed as following diagram The IAD 162 provides two telephone numbers that one is IP telephone number and the other is PSTN telephone number in one device for end users You can make phone call via Internet or PSTN in one telephone set now No more long distance and international telephony fee Especially User still can make phone call when external power is failure The IAD 161 162 also can connect three computers with embedded IP sharing and DHCP server function IAD Gateway User Manual 1 2 Software Specifications gt IAD Gateway
52. ion panel and open the Reboot IAD Gateway Screen Pela Hanne Reboot IADIEL Gateway Tt will take 40 peramds do rrna De tuerk Interface remember ia COMMIT data bedaar rebani _ REBOOT Sippo Fun tan Plane Hack DScr E Press reboot will reset IAD Note To execute reboot please remember to do Commit Data before Reboot System 62 IAD Gateway User Manual Part V Telnet Command Interface This part gives information on how to configure IAD gateway via Telnet command line interface 63 IAD Gateway User Manual 5 1 Login For you first login enter the login root and default no password login root password Welcome to Terminal Configuration Mode Please enter your configuration item usr config Note Login account root or administrator is the default login account and there is no password needed 5 2 Save and Reboot After any configuration has been made user has to save all data and reboot system to make configurations take effect Step 1 Confirm the changed configurations input commit and press enter key to save it Step 2 I nput reboot then press enter key to restart Gateway Step 3 After around 40 seconds Gateway will take effect in new configurations Do not turn off your Gateway or remove the Gateway while saving your configuration usr config passwd set root voip Setting Login
53. l ring and user can pick up the call from PSTN side 3 5 2 2 VoIP TEL is available When IAD has incoming call from PSTN side TEL phone set will ring user can pick the call from PSTN side 3 5 3 Vol P Outgoing Call Default TEL line is intended to make IP call user can just pick up the phone set connected with TEL port and make VoIP call while Vol P network system is available 3 5 4 VoIP Incoming Call When user is communicating with PSTN side with TEL Phone set IAD can t have VoIP incoming call ae ee IAD Gateway User Manual Part IV Web Management Interface a EN This part explains how to configure the IAD Gateway via WEB management E interface 49 IAD Gateway User Manual 4 1 Login and welcome screen Step 1 Start your web browser Step 2 Launch your web browser and enter 192 168 123 123 the default IP address of the LAN port in the Location or Address field Press Enter Step 3 Password request screen will appear as below Please input root in the user name field and no password in the password field MAREE aS gt GR ie ASS ASS Hu 199 100 193 193 EE 140161 Configuniton Web server HAS ea M Sh aS ne ea if i L we _ ma Step 4 Click OK Step 5 After a successful login you will see the welcome screen described next User can click links on the navigation panel at left to go to corresponding configuration screen 43 IAD Gateway User Manual
54. llows users to define their own numbers which mapping to real IP address It is effective only in peer to peer mode When adding a record to Phone Book users do not have to reboot the machine and the record will be effective immediately usr config pbook Phonebook information and configuration Usage pbook print start record end_record pbook add ip ipaddress name Alias e164 phonenumber pbook search ip ipaddress name Alias e164 phonenumber pbook insert index ip ipaddress name Alias e164 phonenumber port numb er pbook delete index pbook modify index ip ipaddress name Alias e164 phonenumber port numb er print Display phonebook data add Add an record to phonebook search Search an record in phonebook delete Delete an record from phonebook insert Insert an record to phonebook in specified position modify Modify an exist record Note If parameter end record is omited only record start_record will be disp lay If both parameters end_record and start_record are omited all records will be display 72 IAD Gateway User Manual Range of ip address setting 0 0 0 0 255 255 255 255 Range of index setting value 1 100 Example pbook print 1 10 pbook print 1 pbook print pbook add name Test ip 210 59 163 202 e164 1001 pbook insert 3 name Test ip 210 59 163 202 e164 1001 pbook delete 3 pbook search ip 192 168 4 99 pbook modify 3 name Tes
55. mic WAN IP Address a valid Gatekeeper for IAD Gateway to get register on is a must In other word it is not workable in Peer to Peer mode while dynamic WAN IP Address Step 5 1P Sharing device must have a function to do P Port mapping Some is named as DMZ some is named as virtual server whatever The VoIP messages from WAN have to completely pass forward to the LAN It is said if the IAD Gateway is assigned a virtual fixed IP Address such as 192 168 1 5 IP Sharing device must forward the VoIP message to 192 168 1 5 27 IAD Gateway User Manual Please see following for example gt Advanced setting gt NAT setting gt DMZ Host setting DMZ Host setting O Activate DMZ DMZ Host IP 192 168 1 5 Step 6 Configure the IAD Gateway IP address for IP Sharing Mode Click Network Interface on the navigation panel In the Network Interface screen enter the IP address Subnet mask and the default gateway in the network table Please follow up your IP Sharing device Step 7 Enable the IP sharing function and put the static IP address in the IP Sharing server address e g 210 59 163 198 and click the OK Metwork Interface a Sai Marks 255 255 Ba ho System a ae Rolin main Default routing gateway 192 fian E Lasa PEPE Conhigeration DACP enable F disable Valer Setting SHIP enable C disable Ehem Pattern SNTI Server Address iss Ps es In Phone Hack GMT B nace
56. n stand as horizontal type 24 2 1 2 Vertical Type 2 1 2 Insert stand board on one side 2 1 2 2 Insert the other stand board on the same side 2 1 2 3 Finally IAD can stand as vertical type IAD Gateway User Manual 25 IAD Gateway User Manual Part IIl Special Applications and Features This part explains how to configure IAD Gateway under special application mode such as behind NAT and how to upgrade firmware 26 IAD Gateway User Manual 3 1 Behind I P Sharing 3 1 1 IP Sharing Configuration 3 1 1 1 One IAD Gateway behind IAD This application is only for the user who is using the IP Sharing device It is said Gateway is connected behind IP Sharing The IP Sharing Device must support the DMZ or Virtual server functions such as ADSL network Step 1 The WAN IP Address obtained from ADSL has two kinds of methods One is fixed IP Address while user applies for one or more fixed IP Addresses Another is dynamic IP Address while user applies for dial up connection way Only when the IP address is fixed user can put IAD behind NAT device Step 2 The LAN IP Address of User s PC can be set as DHCP client in order to gain a valid one Step 3 One can also assign a fixed IP address which belongs to the same network segment as the LAN interface of IP Sharing device Step 4 1AD Gateway must enable the IP Sharing function for the fixed dynamic WAN IP Address Note With Dyna
57. ndex dns server address ipsharing used ip address ifaddr upnp used print Display LAN information and configuration ip Specify WAN ip address lanip Specify LAN ip address mask Set Internet subnet mask gate Specify default gateway ip address IAD Gateway User Manual nat Set NAT service flag On Off dhcp Set DHCP client service flag On Off sntp Set SNTP server mode and specify IP address dns specify IP address of DNS Server timezone Set local timezone ipsharing Specify usage of an IP sharing device and specify IP Specify the upnp mode of ipsharing 0 Off 1 On specify EMS Server ID pwd specify EMS Server password emstime specify EMS cycle time Note Range of ip address setting 0 0 0 0 255 255 255 255 DHCP client setting value On 1 Off 0 If DHCP set to On Obtain a set of Internet configuration from DHCP server assgined SNTP mode 0 no update 1 specify server IP 2 broadcast mode Example ifaddr ip 210 59 163 202 mask 255 255 255 0 gate 210 59 163 254 ifaddr nat 1 ifaddr dhcp 1 ifaddr sntp 1 210 59 163 254 ifaddr ipsharing 1 210 59 163 254 ifaddr upnp 1 ifaddr dns 1 168 95 1 1 usr config Parameter Usages print Print current IP setting and status ip Assigned IP address for Gateway lanip Specify LAN port IP address For NAT function use this command setup LAN IP address assigned to PC or other machine usr config ifaddr
58. ormation included username and password obtained from the service provider usr config security Secuirty information and configuration Usage security line number name username pwd password security print print Display system account information and configuration line Specify which line number you want to set the account name Specify user name pwd Specify password 81 IAD Gateway User Manual Example security line 1 name 1001 pwd 1001 usr config Parameter Usages print print current setting in security command line Specify which line number you want to set into the account Note If you have only one account you can set into linel or line2 using this parameter For example if you set the account into linel linel can accept incoming calls name Specify the username of your account information pwd Specify the password of your account information For example usr config security print Linel account information Username 1001 Password er usr config 5 3 15 voice The voice command is associated with the audio setting information There are four voice codecs supported by Gateway usr config voice Voice codec setting information and configuration Usage voice send G723 ms G711U ms G711A ms G729 ms volume voice level input level dtmf level nscng G711U used1 G711A used2 G723 used3 echo used mindelay t1 maxdelay t2 voice
59. ot After Remote Host Disconnection Enable Disable auto reboot after PPPoE disconnection If user enables this function after PPPoE being disconnected IAD will automatically reboot to re connect and after reboot if IAD still can t get contact with server IAD will keep trying to connect After re connected IAD will also restart system On the other hand if user disables this function IAD won t reboot and keep trying to connect Other items for reference only cannot allow to be configured 50 IAD Gateway User Manual 4 3 5 Voice Configuration Screen Click Voice Configuration in the navigation panel and open the Voice Configuration Screen Vales Settn a De tuerk Interface Colse ard lei 2ml Priority 157101 EET 5 1 lmoLar eks TIF Information Seseem 07231 Erran 571 lo GINA eree Frame Sine ys GM Mo gaz Mn i n e sess PRPoE Config eration cra y Siimer T emshle disakle Valor Stites Suppression Wa dure voice 25 inpia 25 DTMF 23 Suppori Function Pine Bae ice enable disable Dacr a hi Config eration Bun Min Delay 90 Max Delay 150 canis o DE ROM Configura Flash Cinram k Da ar Fe Codec Priority set codecs priority in order Please notice that user can set from 1 to 5 codecs as their need For example user can only set first priority as G723 1 and set the others as x that means only G 723 1 is available Frame Size User can set di
60. pping e 164 number as 10 After phone book data has been set user can dial 10 to make a call for IP 10 1 1 1 After the command completed you can type pbook print to see if the input record is correct When adding a record to Phone Book user does not have to reboot the machine and the record will be effective immediately 99 IAD Gateway User Manual 2 1 4 3 3 Hotline Mode The Hotline Mode is applied in limited two peers User just picks up the phone set and then hears ring back tone or dial tone depended on configurations of destination device Step 1 Set gateway under P2P mode Step 2 Create phone book table with pbook command Step 3 Create a Hotline table with line command usr config sip mode O usr config sysconf service 1 usr config bureau hotline 1 10 2 2 2 201 In this example means if user picks up phone set of IAD Linel gateway will automatically dial out IP address of 201 Step 4 After configuration is finished commit and reboot the device usr config commit usr config reboot 23 IAD Gateway User Manual 2 1 Special Housing Installation Guide IAD has special adjustable housing for vertical or horizontal type Please follow procedures as below to change type you like 2 1 1 Horizontal Type 2 1 1 1 Insert stand board on one side 2 1 1 2 Insert the other stand board on the other side 2 1 1 3 Finally IAD ca
61. re For call forward function it only works under Proxy mode Of course Proxy must support these call features too It is better for user to prepare a telephone set supported FLASH function on keypad If telephone set does not support FLASH function on keypad user can click the Hook quickly by sending FLASH message Note The default FLASH length for Gateway is between 100ms to 300 ms This value must be compliant with your phone set if user press flash but not work please check the flash value of your phone set and adjust it on IAD 3 3 1 Call Hold press FLASH By pressing the FLASH after making a call both sites shall hear the 2nd dial tone generated by Gateway To retrieve the call back just press the FLASH again 3 3 2 Call Transfer press FLASH then transferring number A makes a call to B B press FLASH A and B hear 2nd dial tone B presses C s number C will ring A will hear Ring Back tone B Hangs up this call and A and C can communicate 3 3 3 Call Forward User has to activate deactivate call forward function via pressing keypad of phone set This function is only available under Proxy mode and the Proxy supports Call Forward function There are three conditions for user to set forward function 34 IAD Gateway User Manual 3 3 3 1 Busy Forward While line is engaged or phone set is been off hook incoming call will be forwarded to the assigned number 1 Activate 76 Forwar
62. s not just a representative number for destination s IP Address In other words user dial this e164 number to reach destination destination will receive the number and find out if it is matched to its e164 including Line number in some particular device For example usr config pbook print usr config 5 3 10 pppoe Display PPPoE related information usr config pppoe PPPoE device information and configuration Usage pppoe print open close pppoe dev on off id username pwd password print Display PPPoE device information dev Enable 1 or Disable 0 device open Open PPPoE connection close Disconnect PPPoE connection id Connection user name pwd Connection password reboot Reboot after remote host disconnection usr config 74 Parameter Usages print print PPPoE status dev Enable PPPoE Dial up function open Open the connection close Close the connection id Input the User name ID provided by ISP IAD Gateway User Manual pwd Input the User name password provided by ISP reboot Reboot the PPPoE connection For example usr config pppoe print PPPoE adapter information Device Enabled Status Not initialized User name pppoe Password ER de Reboot No usr config 5 3 11 flash Clean the configuration stored in flash usr config flash Flash memory information and configuration flash clean Clean the configuration stored Note
63. service keypad Select DTMF type O In band 1 RFC2833 faxtype FAX Payload Type range 96 128 inter used 100 102 105 2833type RFC2833 Payload Type range 96 128 inter used 100 102 105 Icdrop Disconnect Supervision Loop Current Drop ON 1 OFF 0 droptime Period of Loop Current Drop ms eod End of Dial Digit setting 0 none 1 2 Callerid Caller ID Type setting 0 Disable 1 FSK BELLCORE 2 DTME dtmfstart DTMF Calleri D Start Symbol dtmfstart DTMF Calleri D End Symbol Example sysconf keypad 0 eod 2 callerid 1 usr config 77 IAD Gateway User Manual Parameter Usages print Print current sysconf settings idtime Set the duration in second of two pressed digits in dial mode as timed out If after the duration user hasn t pressed next number it will dial out all number pressed 1 10 seconds service set SIP Phone to be normal mode or under hotline mode sysconf service 0 1 O for normal service 1 for hotline service keypad DTMF replay type When value is 1 IAD Gateway will transfer DTMF signal via RTP payload as defined in RFC2833 When the value is set to 0 the DTMF type is set as In band faxtype FAX Payload Type Rrange 96 128 inter used 100 102 105 2833type RFC2833 Payload Type Range 96 128 inter used 100 102 105 Icdrop Disconnect Supervision Loop Current Drop ON 1 OFF 0 droptime Period of Loop Current Drop ms eod It will tr
64. t ip 210 59 163 202 e164 1001 usr config Parameter Usages print Print out current contents of Phone Book Users can also add index number from 1 to 100 to the parameter to show specific phone number Note Index number means the sequence number in phone book If users do request a specific index number in phone book Gateway will give each record a automatic sequence number as index add add a new record to phone book When adding a record users have to specify name IP and e164 number to complete the command name Name to represent caller e164 e 164 number for mapping with IP address of caller ip IP address of caller port Call signal port number of caller drop Drop e 164 number when dial out O means to keep e 164 number 1 means to drop e 164 number when dialing out inert Insert digits 1 10 digits usr config pbook add name test e164 100 ip 192 168 13 78 modify modify an existing record When using this command users have to specify the record s index number and then make the change usr config pbook modify 1 name test e164 5678 ip 192 168 1 10 port 1730 drop O 73 IAD Gateway User Manual delete delete a specific record pbook delete 3 means delete index 3 record usr config pbook delete 3 PhoneBook Rules The e164 number defined in phone book will fully carry to destination It i
65. to their own country s tone specification or users defined tone specification usr config phone Phone ringing ringback tone busy tone dial tone setting and notes Usage 87 IAD Gateway User Manual phone ring freq ringON ringOFF ringLevel rbt freqHi freqLo freqHiLev freqLoLev Tone1ON TonelOFF Tone20N Tone20FF bt freqHi fregLo freqHiLev freqLoLev Tone1ON TonelOFF Tone20N Tone20FF dt freqHi fregLo freqHiLev freqLoLev Tone1ON Tone1OFF Tone20N Tone20FF flash fregLo freqHi level loopCurrentLevel onhookLineVoltageLevel phone print ring rbot bt dt flash print Display phone ringing tone configuration ring ringing rot ringback tone bt busy tone dt dial tone flash flash tone ringing configuration set ringback tone configuration set bt busy tone configuration set dt dial tone configuration set flash flash configuration set level Loop Current and On Hook Line Voltage level set ringing frequency 15 100 Unit Hz ringing ring ON OFF O 8000 Unit ms ringing level 0 94 Unit V tone frequency 0 65535 Unit Hz tone freqLevel 0 65535 Unit mVrms tone Tone ON OFF 0 8000 Unit ms level loopCurrent 0 7 20mA 41mA Step 3mA level OnHookVol 0 63 OV 94 5V Step 1 5V Example phone print rbt phone ring 20 2000 4000 94 phone rbt 480
66. up of call progress tones and ring SLIC control bureau To set Hotline function which must be under Peer to Peer mode and switch to hotline service rom ROM file update passwd Password setting information and configuration 65 IAD Gateway User Manual 5 3 2 quit Type quit will quit the Gateway configuration mode And turn back to login prompt usr config quit Disconnecting login root Welcome to Terminal Configuration Mode Please enter your configuration item usr config Note It is recommended that type the quit command before you leave the console If so Gateway will ask password again when next user connects to console port 5 3 3 debug Open debug message will show up specific information while Gateway is in operation After executing the debug command it should execute command debug open as well usr config debug Debug message information and configuration Usage debug add typel type2 open close status status Display the enabled debug flags add Add debug flag delete Remove specified debug flag open Start to show debug messages close Stop showing debug messages Example debug add sip msg debug open usr config 66 IAD Gateway User Manual Parameter Usages status Display the enabled debug flags add Add debug flag Sip sip related information msg voice related information delete Remove specified debug
67. via web management interface please Telnet to the IAD to do more detail configurations Step 6 Connect other PC with LAN Ports Optional If you have more than one PC you can connect them with LAN Ports black on the IAD Gateway Please set these PCs as DHCP mode so that they can automatically get IP from IAD DHCP server DHCP server of IAD can assign 253 IP most Caution To prevent damage to the I AD Gateway please make sure you have connected with the correct power adapter IAD Gateway User Manual 2 1 3 Essential Configuration via Web Management interface This section describes how to setup IAD via Web managementinterface Please follow procedures below to configure essential items before you use IAD gateway 2 1 3 1 Save Data and Reboot After any configuration has been made user has to save all data and reboot system to make configurations take effect Step 1 Click Commit Data on the navigation panel In the Commit Configuration Data screen click the Commit button In the Commit Configuration Data screen will Display Commit to Flash OK when IAD finished committing data Commit Data Hi will take few cecemds COMMIT De tuerk Interface SIP Information System Configuration EEPaE Config eration Phere Patiern Support Function Phone Book DELE Eerli eration Passward ROM Cunfis uraan Flash Elraa oud Data Erbant Svei 10 IAD Gateway User Manual Step 2 Click Reboot
68. ypad DTMF Type set DTMF type User can select DTMF type IAD transmits RFC2833 Payload Type change RFC2833 Payload type This is for special request from the other site if RFC2833 payload types of 2 sites are different it may cause some problem of connection FAX Payload Type Change FAX payload type of IAD Inter Digit Time Set the DTMF inter digit time second To set the duration in second of two pressed digits in dial mode as timed out If after the duration user hasn t pressed next number IAD will dial out all number pressed Caller ID Type Set Caller ID function If user set disable IAD won t display caller ID on Phone set when if receive caller ID information from remote site User can also select caller ID type to be FSK or DTMF according on which type your phone set supports End of Dial Digit select end of dialing key e g set end of dial key as button after finished pressing dialing number then press will dial out 49 IAD Gateway User Manual 4 3 4 PPPoE Configuration Screen Click PPPoE Configuration in the navigation panel and open the PPPoE Configuration Screen HIF Infermatien A Destination DAS primary Rebeot After Remote Host Thiscennection Support Func tiem Plane Bock Eo C of DACP Device Set PPPoe function to be On or Off User Name Set PPPoE authentication User Name Password Set PPPoE authentication password Rebo

IAD 161 162_SIP_100

Contents

Download Pdf Manuals

Related Search

Related Contents