Pancode VoIP Pantel VoIP
Contents
1. Pancode VoIP Pantel VoIP Access Control Door Phones Installation and Programming Manual 8 Technical Specification Power supply Communication interface DC Leakage Imbalance ratio Return loss Relay switching current VoIP protocol supported Supported codecs Echo canceller Quality Enhancement Echo canceller length IP media features In Band Signaling Detection and Generation Dimensions Weight Operating temperature 12V AC 1 5A or Power Over Ethernet IEEE 802 3af compliant Ethernet for voice and for programming lt 10 uA 300 3400Hz gt 46dB 300 3400Hz gt 18dB 2A max SIP RTP RTCP G 711 PCM u A Law at 64 kbps G 726 ADPCM at 16 40 kbps G 727 E ADPCM at 16 40 kbps G 729 A B CS ACELP at 8kbps G 723 1 MP MLQ at 6 3 kbps G 723 ACELP at 5 3 kbps GSM 6 10 Full Rate at 13 2 kbps GSM Enhanced Full Rate 12 2 kbps AMR at 4 75 2 2 kbps G 729E at 11 8 kbps G 168 2002 Compliant with programmable echo tail of up to 128 msec Full duplex acoustic EC Comfort Noise generation CHG Packet Loss Concealment PLC Adaptive Jitter Buffer up to 300 msec Up to 64 msec Automatic Gain Control DTMF TIA464B 19 4 X1 0 2 cm 0 9 kg 20 C to 50 C 4 F to 122 F 212. Default port 5060 Legal entry Up to 8 digits 0 9 Displays the time interval for the unit to register on the Proxy server and to indicate Live status Legal entry 0 9999 The setting in this field takes effect only when Enable Auto Registration checkbox is selected A Low MU Low options enable to select between VoIP codecs supported by the PBX Microphone Volume enables to set the microphone volume level as a two digit parameter Legal entry 00 63 00 sets Mute mode Speaker Volume enables to set the speaker volume level as a two digit parameter Legal entry 00 63 00 sets Silent mode When checkbox is selected activates a field under it This field contains a virtual value 0 256 that represents a threshold for human voice detection When voice is detected the unit will establish a connection with the extension according to the programming in Day and Night numbers recommended value 20 25 This parameter is required for manufacturing purposes only Switching between Full and Half duplex voice transmission modes Legal entry 1 half duplex mode 2 full duplex mode Enables DHCP service support IP Door panel will get IP settings automatically in case that DHCP server is present in the LAN List of available IP Door Panel configuration and functionality These settings define the device functionality as a panel or Pancode Standard dialing sets the unit to standard dialing operat
3. ISDN timing interface modes with which this device is compatible In the GCI mode the device can communicate in either of the two 64 kbps B channels This parameter may be changed by a qualified and authorized person only The Interchip Digital Link interface is one of two standard timing interface modes with which this device is compatible In the IDL mode the device can communicate in either of the two 64 kbps channels This parameter may be changed by a qualified and authorized person only Displays the name that will appear on the digital station display when a call is received from the unit depending on the VoIP PBX support for this feature An identifier for the TFTP server on a TCP IP network where configuration files will be stored The TFTP server can be activated by using the Third Part Company tftp software For example Tftpd32 application which can be found on the following URL http www snapfiles com download dlTftpd32 html Previously saved configuration file name which has to be written here and IP Door Panel will upload it using tftp server settings Internal IP Door Panel Firmware file name Uploading procedure is the same as Configuration file Internal IP Door Panel Kernel file name Uploading procedure is the same as Configuration file This parameter may be changed by a qualified and authorized person only 17 Pancode VoIP Pantel VoIP Access Control Door Phones 7 Telecom Installation and Progra
4. peer to peer network Legal entry 5 to 20 characters 0 9 A Z a z Contains the unit authorization on the SIP proxy server Legal entry 5 to 20 characters 0 9 A Z a z Identifies the Pantel VoIP Pancode VoIP device on the TCP IP network Legal entry digits 0 9 only Example 192 168 21 10 A mask that determines to which subnet an IP address belongs Legal entry digits 0 9 only Example 255 255 255 0 An identifier for the default gateway on a TCP IP network for cases when the Proxy server presents out of local LAN network Legal entry 0 9 digits only Example 192 14 21 210 15 ITS v Telecom Pancode VoIP Pantel VoIP Access Control Door Phones Installation and Programming Manual User Domain Registar Address Proxy IP field Registar port Proxy Port field Auto Registration Registration expire Registration Interval Codec Type Unit Volume level Far End Speaker Volume Level VAD Voice Activity Detection Threshold Auto Start DSP Firmware version Voice Operational Mode Enable DHCP Product Type Dial Mode In most cases it is the same as the Registar Address Proxy server IP address In special cases it is required to enter Company Domain IP address An identifier for the SIP Proxy server on a TCP IP network Legal entry 0 9 digits only Example 192 14 21 210 Designed to contain the number of the TCP IP port used by the unit for communication with SIP Proxy server IP PBX
5. f Pancode VolP Pantel VoIP Access Control Door Phones Telecom Installation and Programming Manual Table of Contents 1 WPVEFOG UCUION esate sacs ves dicated ect aes ies anes E E bse cece ha hates Layee lg ea destheea es ea eas Seago eae 2 1 1 Pancode VoIP Pantel VoIP Kit CONTENTS ecccecceeccee cece cece eeceeeceeeeeeeeceeeceeeceeeeaeeeseeseeeeetneeneeeaeess 3 2 PHYSICAlDESGr iO TON iiss co eeecasci nes Sas saces eteed dp wep a a E E eaten Hane A E e 4 ZA Pancode VoIP Eront Panel ecseri ianoaiiaea aa tah EEE a AE Sa NE aani 4 22 Pameli MOIPIRFOMU PAG esee ea ects ada tes a A a A ATOE 5 3 WSCA ATOM E A E E N E E E N A E 6 4 Pancode VolP Pantel VoIP Schematic Setup cccceccececececececeeeceee cece eesaeeceeeceaeeeaeceseecaeeeseeeseeseeetseseseeeseeees 7 5 Installing the Pantel VolP Pancode VOIP sssini inneir aA nave EE EEEE 8 6 Adjacent Access Control DEVICE esgorodd SAAE AEEA EARE EE SAER E 11 I PrograMMiINg 0 ccceecceeeceeeeececeeeeceeeeeeeeeceaeeeceeeeeceeeseeeeecaaeeeceeeeceeeesaeeecaeeeceeeseneescceeecceeecseeesseeecteeeenteeenaees 13 7 A S arching fora Device im LAN os cs saesexcsieendecee seg asked het tp tance E ENR AEN 13 7 2 Application Interface vcd ieee sexs arepane nia Ee E E E E AEE E AET E EEES 14 753 e a E a E E A T A A E A 15 7 4 VolP Dialing settings 0 ccccccccceeececeeececececeeeeeceaeeeceeeeeceeeseaeeeceaeeeceeeseeeecaeeeceeeeceeesesaeeesseeenteeenaees 18 8 Technical Specification c
6. of an Ethernet cable to the local network The programming application is launched from the web browser preferably MS Internet Explorer version 5 5 or higher It is possible to run the application by typing the following address in the address bar http XXX XXX XXX XXX pancode Figure 10 S ITS Pancode IP Microsoft Internet Explorer File Edit view Favorites Tools Help O Back gt x B A a Search Se Favorites Address E http 192 166 1 229 pancode SSS SSS Figure 10 ITS Pancode IP Web Page 7 1 Searching for a Device in LAN When the IP address is unknown it is possible to find the unit in the LAN using the QUERY utility from the NOTE Unit location through a query is possible only when the unit MAC installation CD address is known It appears on the label attached to the rear panel of the device To find the unit in the network a Insert the installation CD and copy the query exe file from Software directory to the local hard drive b Start MS Windows DOS prompt application c Access the directory in which the query exe application exists d Enter the following command query XX XX XX XX XX lt Enter gt where XX XX XX XX XxX is the MAC address A search for the device takes place at the end of which the unit IP address appears Figure 11 C UOIP NEWFIRMWARE gt query 66 61 62 63 64 12 Target IP 192 168 1 38 C U0OI P NEWFI RMWARE gt Figure 11 Searching for Device Us
7. Telecom Pancode VoIP Pantel VoIP p a a OrtA h ar 2 107 Uctoper ZUU Pancode VoIP Pantel VoIP Access Control Door Phones Telecom Installation and Programming Manual NOTICE This publication refers to the PANCODE IP and Pantel IP Door Access Control devices Release 2 Additional copies of this manual may be obtained from ITS Ltd Reproduction of this manual or parts thereof without written permission from ITS is strictly prohibited ITS Ltd reserves the right to modify the hardware and software described herein without prior notice However changes made to the hardware or software described do not necessarily render this publication invalid WARRANTY In the event that the product proves to be defective in workmanship or materials within a period of one year from date of shipment ITS Ltd shall repair or replace the same at its discretion Transportation will be the responsibility of the dealer distributor Under no circumstances shall ITS Ltd be liable for consequential or special damages loss of revenue or user dealer expenses arising out of or in connection with the use or performance of the product whether base on contract tort or any other legal agreement The following shall void the above warranty malfunctions resulting from fire accident neglect abuse or acts of God use of improper electrical power or repair of tampering with or alteration of the product by anyone other than ITS authorized
8. ation process which can take up to 20 seconds The initialization completion is indicated by short busy signal 2 Device can be detected in the LAN by using the MAC address shown on the label 3 When SIP parameters are updated an automatic power reset is required The programming is not done in real time Make sure to apply the settings to the unit by selecting Communication gt Send Parameters on the main menu ITS Pancode VoIP Pantel VoIP Access Control Door Phones Telecom Installation and Programming Manual Ethernet RJ 45 12V Connector Wire Connectors Figure 6 Unit Connectors Figure 7 RJ 45 Connector 10 Pancode VoIP Pantel VoIP Access Control Door Phones Telecom Installation and Programming Manual 6 Adjacent Access Control Device This section describes adding an access control device to an existing Pantel VoIP Pancode VoIP and adding a Pantel VoIP Pancode VoIP to an existing access control device The key difference between these two installations is which access control device controls the door lock relay To add an access control device to a Pantel VoIP Pancode VoIP When activated the access control triggers the Pantel Pancode SW terminal which activates the door lock relay and opens the door For this type of installation the access control device N O output wires are connected to the Pantel VoIP Pancode VoIP Switch terminals see Figure 8 Lock Relay Sw
9. cccccccceccccceecceeeeeeeeeeceseceececeeeeseceseeeceeeceeeceeeceeecaeecaeesaeessaeeneeeceeeneeeeaeeneeeaeeees 21 Pancode VoIP Pantel VoIP Access Control Door Phones Telecom Installation and Programming Manual 1 Introduction This guide provides installation and programming instructions for the following products Y Pancode VoIP outdoor piezo keypad unit 7 Pantel VoIP outdoor piezo keypad unit The Pancode VoIP and Pantel VoIP are smart wall mounted access control door phones connected to a local Voice Over IP VoIP network of a VoIP PBX allowing door entry control They are available for outdoor installation in an aluminum unit with a piezo keypad As an option these units can be equipped with an internal black amp white or color high quality pinhole camera The Pancode VoIP and Pantel VoIP have the following features Integration with local LAN and VoIP networks Vv Vv Authorized registration with existing VoIP switching system Proxy Vv Vv Two different operation modes Vv X Standard for direct dialing to any destination number Speed dial for one touch dialing to internal or external subscribers Automatic busy amp disconnect detection Door opening from any extension Door opening from Bypass Switch button Programmable day and night destinations High quality speakerphone with separate volume control Entry access code supports up to ten codes Works in conjunction with card readers and security devices Pr
10. djacent access control devices such as card reading devices see Section 6 The provided 12V AC external power supply should not be located further than 10m 30ft from the unit These units also support Power Over Ethernet PoE meaning that they could operate when connected to Ethernet without mains However the current provided by the PoE supply is insufficient for opening a door If your system is equipped with door lock relay make sure to use the external supply Figure 5 shows the terminal locations on the wire connector provided with the unit This connector is attached at the base of the internal component All wiring to the unit is attached to the wire connector NOTE There may be LINE pins in the connector but they are not active with this product and cannot be used When holding the unit as displayed in Figure 6 the first pin from the right is the first 12V pin The Pantel VoIP Pancode VoIP supports a bypass switch installation This allows opening the door with a hardwired switch A bypass switch should be connected to the SW and SW terminals 12V 12V l N C option1 Connect CMN to an External o N O option2 Device l DLR p Connect A DLR option 3 to Door DLR Lock 9 e DLR option4 Relay i Bypass Switch SW Contact Detection e Bypass Switch SW Figure 5 Connectors Scheme ITS Pancode VoIP Pa
11. el VoIP Access Control Door Phones Installation and Programming Manual Speed dialing mode Door Access Codes Speed dialing mode destination numbers Regular Normal Direct dialing mode First digits of Extensions Regular Normal dialing mode Door Access Codes Call Button definitions Door opening from extension code No answer timeout The Main Parameters screen contains the following operational buttons Submit Reset to default Reboot Upload Config File Save Config File Upload Firmware Upload Kernel Upload modified settings to the Door Unit Reset Door Unit to the factory default settings Restarts the Door Unit Upload previously saved Door Units configuration file Note Saved file renamed to Config CFG Save existing Door Panel configuration as file on local PC drive the existing configuration file will be saved with extension Config SAV For uploading this file need to rename saved file to extension Config CFG Activate the updating of the Door Unit s internal firmware This operation requires original firmware file provided by manufacturer or local dealer 7 3 System Parameters The following table details the system parameters You may require assistance from your LAN administrator Parameter Name and Parameters area Account Name username Account Password password IP Address Local Address Subnet Mask Default Gateway Contains the unit identification as an SIP proxy server account or VoIP
12. estination use following format XXX XXX XXX XXX where XXX are digits the address is prefaced by an asterisk and an asterisk is used as a separator The access door opening code in speed dial mode must start with 0 Day number field contains the number of the target phone which will be dialed when a visitor presses the Call button when the device is configured to operate in Day mode You may insert up to 20 entries so that a visitor could call different extensions directly Legal entry Digits 0 9 ABCD Night number field contains the number of the target phone which will be dialed if a visitor will press the Call button when the device is configured to operate in Night mode You may insert up to 20 entries so that a visitor could call different extensions directly Legal entry digits 0 9 ABCD Error number field contains the number of the target phone which will be dialed if a visitor will dial an incorrect access entry code more than three consecutive times You may insert up to 20 entries Legal entry digits 0 9 ABCD Contains the number of the target phone which will be dialed if a destination number dialed by visitor is not answer during specific time interval You may insert up to 20 entries Legal entries digits 0 9 ABCD See also No Answer Time Out parameter enables to set a code of up to four digits which could be dialed from any extension during conversation to open
13. eypad Figure 2 Speaker Call Button Microphone Figure 2 Pantel VoIP Front Panel TS Pancode VoIP Pantel VoIP Access Control Door Phones Telecom Installation and Programming Manual 3 Installation The Pantel VoIP Pancode VoIP is mounted on the provided installation bracket This mounting bracket should be installed as shown in Figure 3 Figure 3 Installation Bracket To install the wall bracket a Measure and mark the location on the wall where the holes will be drilled for the mounting bracket b Drill the holes and insert the wall anchors into the holes c Attach the mounting bracket using the provided wall screws Pancode VoIP Pantel VoIP Access Control Door Phones Telecom Installation and Programming Manual 4 Pancode VoIP Pantel VoIP Schematic Setup The Pancode VoIP Pantel VoIP unit is connected to the VoIP PBX as a SIP extension or via any IP router Network HUB Switch etc The unit powers the door lock provided it is powered by an external supply and not PoE Figure 4 details the unit schematic setup PBX Il oe z VolP Network LAN Pancode VolP Pantel VolP Extension Door Lock 0 TV Monitor Figure 4 Schematic Setup Pancode VoIP Pantel VoIP Access Control Door Phones Telecom Installation and Programming Manual 5 Installing the Pantel VoIP Pancode VoIP The Pantel VoIP Pancode VoIP can be installed as an individual access control or used with a
14. ial mode fields contain door opening codes in speed dial mode Each field can contain a code of up to 8 digits which opens the door lock Legal entries 0 9 digits only All codes in this mode must start with 0O 18 ITS v Telecom Parameter Regular Prefix Speed Dialing Numbers Destination numbers 11 35 Call Button Dialing Day Mode destination Call Button Dialing night mode destination Call Button Dialing Error mode destination Call Button Dial no Answer Forward No Answer Open Door Activation Door opening code from extension Pancode VoIP Pantel VoIP Access Control Door Phones Installation and Programming Manual Description Prefix for direct dialing field contains the first digit of a target phone number to which it is possible to call directly You can enter up to eight prefixes using a coma separator Example Defined prefixes 1 2 5 enable to dial directly to numbers beginning with 1 2 or 5 Digits defined as a direct call prefix may not be used as first digits for access door opening code The direct dialing feature requires a SIP proxy definition In case of Peer To Peer mode VoIP gateway IP address can be used as destination and set in the SIP proxy address Speed dialing subscribers list contain from to 2 to 20 lengths of subscriber s phone numbers Legal entry 0 9 It is possible to enter 25 codes indexed from 11 to 35 If an IP address is used as a d
15. ing Query 13 TS Pancode VoIP Pantel VoIP Access Control Door Phones Telecom Installation and Programming Manual 7 2 Application Interface When running the application the main screen opens comprising the navigation menu parameters fields and functional buttons Figure 12 ITS Pancode IP Microsoft Internet Explorer File Edit view Favorites Tools Help Om O 2 AO pe trom Ol 4 LJara BS Address http 192 168 1 185 pancode System username fas password COLI LocalAddress P 2681185 CO SubnetMask P 52552550 I i DefaultGateway fisziesi2 UserDornain fisetcst1s7 RegistrarAddress fi92168 1187 RegistrarPort fur E AutoRegistration Enable More about ITS RegistrationExpire fc i E Customer Service Codec Type Atew unitolumeLevel Bso o OoOo peamine farEndVolumeLevel fs Contact US vadThreshold eS rti CO C Auto Start JEnable z Figure 12 Application Interface The navigation menu contains the following items System Authorization parameters Local network parameters Proxy server parameters Codec Type Volume settings Time mode DHCP support Dialing mode Door opening time Auto Answer mode Video Camera operational mode optional Video camera operational mode depends on the Door Unit s hardware configuration 14 ITS v Telecom VoIP Dialing Settings Pancode VoIP Pant
16. ion mode In this mode it is possible to make a direct call to an extension or enter a door opening access code Speed dialing sets the Pancode VoIP to speed dialing operation mode In this mode it is possible to make a call using a two digit speed dial code 11 to 35 to internal or external subscribers 16 ITS v Telecom Pancode VoIP Pantel VoIP Access Control Door Phones Installation and Programming Manual Time mode Number of errors Panel Session Time Out Maximum Conversation time Door open time VCR Mode Low mode GCI Idi Mode Presentation Name Auto Answer TFTP Server IP address Config File name Firmware file name Kernel File name Day mode and Night mode enables to select the operational mode of the unit Number of Door Access Code error retries when IP Door Panel will implement calling to Error Number Call max duration displays the time interval for conversation with the target phone s subscriber You may insert the time parameter in two digit format in seconds Legal entry 10 99 seconds Unlimited time interval with the 00 settings Open door interval enables to set the time interval during which the door lock remains open Parameter defines the digital camera functionality Depends on the firmware and hardware configuration Contact local dealer or manufacturer for further details General Circuit Interface is the second of two standard synchronous 2B D
17. itch N O Output Figure 8 Controlling Lock Relay 11 TS Pancode VoIP Pantel VoIP Access Control Door Phones Telecom Installation and Programming Manual To add a Pantel VoIP Pancode VolP to an access control device The access control device opens the door when the Pantel Pancode triggers the access control device For this installation the access control device Bypass Switch SW wires are connected to the N O and CMN terminals of the Pantel Pancode The door lock relay wires are connected to the access control device see Figure 9 Lock Relay N O amp CMN Figure 9 Access Control Controlling Lock Relay Connection schematics The Pantel VoIP and Pancode VolP offer multiple wiring options 7 Option 1 For use with an external device which requires the unit to be set up as Normally Closed 7 Option 2 For use with an external device which requires the unit to be set up as Normally Open 7 Option 3 For use with the powered unlocked state lock relay most common y Option 4 For use with the powered locked state lock relay recommended for safety purposes 12 Pancode VoIP Pantel VoIP Access Control Door Phones Telecom Installation and Programming Manual 7 Programming The Pancode VoIP Pantel VoIP units are programmed through web based GUI interface This process can be implemented after the unit has been installed on the wall since it requires the connection
18. mming Manual IP Camera Type Type of the digital video camera used in the IP Door panel IP Camera Enabling DHCP Enables the DHCP mode for the digital video camera IP Camera IP Address Identifies the Pantel VoIP Pancode VolP digital video camera on the TCP IP network Legal entry digits 0 9 only Example 192 168 21 10 IP Camera Subnet mask A mask that determines to which subnet an IP address belongs Legal entry digits 0 9 only Example 255 255 255 0 IP Camera Gateway An identifier for the default gateway on a TCP IP network IP Camera stream Type The video stream type supported by the digital video camera Feature activity depends on the IP Door Panel hardware and software configuration Contact the local dealer or manufacturer for details Software Version Displays the IP Door panel internal software number Hardware Version Displays the IP Door panel internal hardware edition number 7 4 VoIP Dialing settings The VolP Dialing Parameters screen displays the dialing and door opening definitions NOTE Pancode VoIP has two dialing modes standard and sped dial Pantel VoIP has the standard mode only The VoIP Dialing screen contains the following areas Parameter Name and Parameters area DTMF Transfer type Defines the mode of providing DTMF tone information in the SIP VoIP network Possible choice RFC 2833 or Transparent In Band DTMF Speed Access Codes 1 to 10 Access Door Opening Codes speed d
19. ntel VoIP Access Control Door Phones Telecom Installation and Programming Manual NOTE For the installation of the powered unlocked state use DLR and DLR For the installation of the powered locked state use DLR and DLR this is recommended for safety purposes The wiring connector is a screw connector type In order to attach a wire you must insert the stripped end of the wire into the proper terminal and tighten the terminal screw This will crimp the wire connection To Install the Pantel Pancode VoIP a Remove the cover from the Pantel VoIP Pancode VoIP unit and disconnect the wire connector found at the base of the internal component Connect the two 12V lead wires from the 12V AC power adapter one to each of the 12V terminals Figure 5 Connect the Ethernet cable to the RJ 45 LAN socket Figure 6 and Figure 7 by means to program the unit using the Web based GUI see Section 7 Connect the door lock relay wires to the DLR and DLR terminals or If the door lock relay is a powered locked state type lock connect the door lock relay wires to the DLR and DLR terminals If a push button switch is used connect the push button wires to the SW and the SW terminals Plug the wire connector to the base of the unit s inner component Switch on the power to the 12V adapter NOTE 1 After power up or reset the Pancode Pantel device starts an initializ
20. ogramming via Ethernet interface using a web based GUI application Acoustic echo canceller Automatic gain control AGC SRTP encryption and authentication Support for video over VoIP optional Shr T SESS TSI BR ES ES PSS ES ES eR es SS SES IN ES Smart looking durable design S Pancode VolP Pantel VolP Access Control Door Phones Telecom Installation and Programming Manual 1 1 Pancode VolP Pantel VolP Kit Contents The contents of the Pancode VolP Pantel VolP are as follows 7 Pancode VolP or Pantel VoIP unit 7 External 12V AC power supply 7 Ethernet cable y Installation CD 7 S Pancode VolP Pantel VolP Access Control Door Phones Telecom Installation and Programming Manual 2 Physical Description The Pancode VolP and Pantel VolP are attached to the wall using a bracket and screws These units are hardwired and powered by an external 12V AC transformer included in the package The Pancode VolP and Pantel VolP dimensions are 7 Height 19 4 cm 7 Width 10 2 2 1 Pancode VolP Front Panel The front panel of the Pancode VolP unit contains a built in speaker a microphone and a touch keypad Figure 1 Speaker Keypad Microphone Figure 1 Pancode VolP Front Panel Pancode VoIP Pantel VoIP Access Control Door Phones Telecom Installation and Programming Manual 2 2 Pantel VoIP Front Panel The front panel of the Pantel VoIP unit contains a built in speaker a microphone and a touch k
21. the door 19 ITS v Telecom Pancode VoIP Pantel VoIP Access Control Door Phones Installation and Programming Manual Access Codes 1 10 Peer IP Address Peer Mode No answer Time Out Off Hook Time Out Access Door Opening Codes fields contain door opening codes Each field can contain a code of up to 8 digits which opens the door lock Legal entries 0 9 digits only An access door opening code cannot begin with digits that are used as direct call prefix number Specify the target Peer device IP address when Peer mode is activated Used mostly for functionality testing purposes Specify the following type of operation Visitor dials any free up to 3 digits number and IP Door panel try to establish SIP connection with the target Peer device where dialed digits used as fourth quarter of the IP address For example Peer IP Address is 192 168 21 XXX where last XXX digits are insignificant Visitor dialed 151 Door panel started to establish connection with the IP address 192 168 21 151 Time interval when a call will be forwarded to the another destination specified in the Call Button Dial no Answer Forward No Answer parameter when destination dialed by visitor did not answer This parameter is relevant if the Auto Answer mode is disabled Specify a maximum time interval in seconds when the IP Door Panel can be in the No Answer mode during incoming call before rejecting the call 20 ITS Telecom
Download Pdf Manuals
Related Search