User Manual - CS
Contents
1. E Auto Battery Cut Off automatic recognition and intelligent monitoring of the batteries to avoid deep discharging m TPI Temperatur monitoring and display safe protection against thermal damage E CCD Copper Cool Drive Technology 8 track conductors of copper for minimized power loss and for low temperature of the speed controller E PCB Integrierte Powercapacitor maximum protection without high resistant cables E DCB Drive Controlled Break Software rational speed controlled brea king efficiency at all speeds E Re Charging battery will be charged at breaking for more running time and power E Mega BEC System powerful and stable for interference free operating E MegaFlex Powercable high flexible 4 0 mm und 2 5 mm LowDrill silver stranded wires for maximum power E PC Interface compatible more settings for the professional racer 8 Additional Features for the The following settings can be done with the optional PC interface C130208 These settings can be preset at home with an PC laptop or at the racetrack E Power Programs Display of the different power programs E Profile memory save user profiles with details about the tracks E Launch Control adjustable start automatic for maximum acceleration E Current limiter configure the motor for the track conditions E Automatic brake adjustable braking power at neutral throttle for tight corners E Brake MIN adjustable minimum braking power whe2. 4 7 Cells Number For Brake of cells ward MIN Hall Sensor sensor less Sensor cable recom 4to yes 15 mended yes recom 4to yes 15 mended yes recom 4to yes 15 mended yes recom 4to 7 yes 15 mended recom 4to6 yes 15 yes mended erforderlich fur max Leistung aa aa aa 4 8 8 4V 4 8 8 4V 4 8 8 4V Automatic Lipo and 4 7 Cells erforderlich fur max Leistung Automatic Lipo and 4 7 Cells erforderlich fur max Leistung recom 4to6 yes 15 yes 4 8 mended 2N Very less 7 less grip nor mal high grip Recommended classes Offroad 2WD 4WD 1 12 Pro10 Saloon cars Offroad 2WD 4WD 1 12 Pro10 Saloon cars Offroad 4WD 1 12 Pro10 Saloon cars all models fun classes all models fun classes Saloon cars Offroad 2WD Standard Vale Attention Adjust gear ratio check motor temperatur Saloon cars Offroad 2WD Standard fall Attention Adjust gear ratio check motor temperatur Saloon cars Offroad 2WD Standard Wale Attention Adjust gear ratio 50 shorter check motor temperatur Selecting Programs E First of all select one of the programs in the overview E Press the setup key for more than 3 seconds until you hear a sound Now you move the throttle trigger from full speed to full brake as much as it corresponds to the number of the program Please note that the last movement to the
3. ELECTRONIC Do not leave you RC model unsupervised as far as a battery is connected In case of a failure this can be cause fire The speed controller and other electronic components should never get in touch with water The speed controller must be protected against dust dirt humidity and vibration If the motor is connected to the speed controller the motor may never be run with an external battery This destroys the speed controller and the guarantee is lost Never reverse connect the polarity of the speed controller Use a reverse connected protection plug systems Avoid short circuits and blocked motors All cables and connections must be isolated properly Short circuits can destroy the speed controller The speed controller may be only used in battery driven radio controlled models Another use of the speed controller is not permitted The use in a model for carrying of passengers is forbidden First check the holdup of your radio control hold you model tight before using you model It is not allowed to modify the speed controller in another way as descri bed in this manual Exclusion of liability The retention of the assembly and the users instruc tion as well as the conditions and methods of installation operating use and maintenance can not be supervised by CS ELECTRONIC Therefore CS ss accmonc CS ELECTRONIC does not take over any liability for losses damages or costs which result from a faulty use or operating
4. neutral position counts as one Every movement will be confirmed from the speed controller with a sound which also refers to the program number The last movement to the neutral position is also counted as one but you do not hear a sound for that Power Program 1 E on q E Press the setup key for more than 3 seconds E Throttle trigger remains in neutral position E Controller confirms after 10 seconds the power program 1 with 1 sound Power Program 2 e n lt x e i e y ay r E Press the setup key for more than 3 seconds E Throttle trigger on full speed speedo cheeps 1x and back to the neutral position 2 E Controller confirms after 10 seconds the power program 2 with 2 sounds Power Program 3 Ss y x 5 gt y gt s B s t E Press the setup key for more than 3 seconds E Throttle trigger on full speed speedo cheeps 1x now full brake speedo cheeps 1x and back to the neutral position 3 E Controller confirms after 10 seconds the power program 3 with 3 sounds Power Program 4 Ss e SS E E Press the setup key for more than 3 seconds E Throttle trigger on full speed speedo cheeps 1x now full brake speedo cheeps 1x full soeed again speedo cheeps 1x and back to the neutral position 4 E Controller confirms after 10 seconds the power program 4 with 4 sounds Power Program 5 E Press the setup key for more than 3 seconds E Throttle trigger on full spee
5. side makes sure the position and the 4 polarity The black receiver plug is con nected to the plug in place 2 of your receiver Polarity of the receiver connection Please observe the polarity as follows Red is receiver Black is receiver White is receiver signa Ye Negative J h Negative Positive Positive Signal Sensor connection If the brushless motor is used in the sensor mode the motor must be connected with a sensor cable to the speed controller before you switch on the speed controller The sensor cable included is equipped with a standardized 6 pole JST plug for the connection with the mostly used brushless motors The 8 pole plug is plugged in the sensor jack of the speed controller Faulty sensor cables must be replaced immediately A spare cable or cables with different length can be ordered from CS ELECTRONIC Assembly of the air fan If you use brushless motors with less than 4 5T or if the ambient temperature is high we recom mend the use of the included air fan The fan is assembled with 4 screws on the cooling surface of the speed controller To ensure the 6 V power supply the cable of the fan is plugged in a free plug in place of the receiver Requirements for the basic settings are the following conditions a h The power cable A B und C of the speed controller must be con nected to the motor The controller BEC cable is connecte
6. Lu lt x S N O oa T N Power Specs 120 A 800 A Peak 6 Power Programs 3 Aktive Stock Programs 4 A Mega BEC 4 8 8 4 V 2 LiPo LiFe Forward Brake Forward Brake Reverse User Manual Optimized for 1 12 Pan Car 4 cells 1 10 Onroad 5 cells 1 10 Offroad 6 cells 1 10 Onroad 6 cells Stock motors NiCd NiMH LiPo Lilo LiFe and much more LOCKETT Motor Specs ere a Te Tstless Contros Syste above 2 5 Turn m 4 8 12 0 V Sensor Motors Sensorless Motors Order No C130200 C ee LT 1 Dear Customer ssesssssssssssssssseessesssssssseessesssssssosessesssssso 2 2 Range Of Application ssessesesseoseseesessessecsesessessesseceeseeseese 2 Zi InstahlatoN cecen 2 4 Connection of the componentS sessessesesoessesseosecoesseessesee 3 5 Basic Setting controller Transmitter set Up s0ssscccssseeees 4 6 Power programs Overview and SettING ccsccsccsecsecsseees 4 Ja Features prenin a E EEEE ENES 8 8 Additional features for the serious racel cssccssseseeescees 8 SD Di BIO SINGS scoren aaa 8 10 Reset to factory defauls csccssccesccscccsscesccsccesscescoeees 10 11 Safety precautionS eseessessesseoescessecsscssceesecseosecseseeseeseee 10 12 Technical dataserier i 11 1i ACCESSES so 11 14 24 month guarantee sessssessosesecessecscscsesessesecsesesesseseceee 11 15 Service returns ccccccccsscccscccc
7. attery cables Crystal defect Exchange crystals Car does not stop Set the trim triggers at the transmitter Water or humidity damage send in for repair 10 Reset to Factory Defauls When performing a reset to the factory defaults all data of the program will be set to the factory defaults All setup parameters done are lost The speed controller is set to all values when you bought it a b c d e 10 Remove the sensor cable if it is connected Press the setup key and hold it pressed After 3 seconds you hear a sound hold the setup key pressed until 3 short and 1 long sound can be heard Now let the setup key off Both LED s go off The controller now deletes all parameters of the selected program This will be confirmed with additional sounds At the end both LED s go on This procedure takes some time please wait f g Switch off the speed controller now and wait for appr 2 Seconds Now switch on the speed controller again and perform a transmitter setup Please note that you should set up the transmitter before as described in 5 d to g Select the power program you nee as described above 11 Safety Precautions Not for children below 14 years No toy The CE certificate of this speed controllers does not exempt from the obligation to handle this product with care Use only motors from CS ELECTRONIC which are intended for the used voltage range Use only high performance batteries from CS
8. carp Please contact your municipal administrati on for the details of the disposal facility in question CS CS ELECTRONIC
9. ches off Motor defect Exchange motor Sound 3x Motor not properly Check motor cables connected and connect the right way Permanent operation Break driving and wait for the controller coo ling down Motor does not start Motor defect Check motor and but exchange Brake too weak too weak Gear ratio much too Use a very much long smaller pinion Steeringservo works Receiver cable is wrong Check connection and or not connected reconnect cable Receiver plug in place 2 of the transmitter is not tranmsitter to 100 high enough and perform a trans Receiver cable defect a receiver mitter set up Motor does not start Receiver cable of the Check connections an ower and controller is wrong or reconnect j Transmitter Setup Set end point at the or i Steering Servo does not connected Servo Receiver plug nonenouahtop speed mixed up transmitter to 100 not work in place 1 and perform a trans Speed controller Re mitter set up ceiver plug in place 2 Motor defect Exchange motor Receiver defect Too much wear of the Setting of the end point Set end point at the CS CS ELECTRONIC a DIETAN a o Display failure Interference Power of the transmit Check batteries and an ter too low tenna of the transmit ter Antenna must be fully extended Reason Antenna in the car is Refer to installation rolled up or shorter than 35 cm Antenna is near the Refer to installation speed controller and or the b
10. d 1 full brake 2 full speed 3 full brake 4 and back to the neutral position 5 E Controller confirms after 10 seconds the power program 5 with 5 sounds CS CS ELECTRONIC Power Program 6 Power Program 9 i E Press the setup key for more than 3 seconds E Throttle trigger on full speed 1 full brake 2 full speed 3 full brake 4 full speed 5 and back to the neutral position 6 Power Program 7 i E Press the setup key for more than 3 seconds E Throttle trigger on full speed 1 full brake 2 full speed 3 full brake 4 full speed 5 full brake 6 and back to the neutral position 7 E Controller confirms after appr 10 seconds the power program 7 with 7 sounds Power Program 8 E Press the setup key for more than 3 seconds E Throttle trigger on full speed 1 full brake 2 full speed 3 full brake 4 full soeed 5 full brake 6 full soeed 7 and back to the neutral position 8 E Controller confirms after 10 seconds the power program 8 with 8 sounds CS s e1ecrn0ome E Controller confirms after 10 seconds the power program 6 with 6 sounds E Press the setup key for more than 3 seconds E Throttle trigger on full speed 1 full brake 2 full speed 3 full brake 4 full soeed 5 full brake 6 full soeed 7 full brake 8 and back to the neutral position 9 E Controller confirms after 10 seconds the power program 9 with 9 sounds Please note The timi
11. d to the receiver in plug in place 2 The sensor cable is not connected to the Sensor USB jack The jack must be open Now switch on the transmitter and you can begin with the basic set up The direction of rotation of the throttle function of the transmitter must be set to NOR normal Special setting for Futaba transmitters The direction of rotation must be set to REV reverse The end point adjustment of the throttle EPA must be set to 100 and the end point of the brake must be set to 150 if possible otherwise 100 too With very cheap transmitters this setting is not be possible use the standard settings Now connect the battery to the speed controller take care of the polarity The switch of the CS Rocket controllers is now set to ON j Press the setup key for more than 3 seconds until you hear a sound k Push the throttle trigger to full throttle you hear a sound again Now you push the throttle trigger to full brake until you hear a sound again m The throttle trigger is now moved back to the neutral position and the basic setup is finished n Both LEDs of the speed controller go out and three sounds confirm the correct setup Please note this takes appr 10 seconds Please wait for the sounds for the confirmation Check of the basic setup Speed Controller Transmitter Adjustment a in neutral position of the throttle trigger both LEDs shine red and yellow b at slow acce
12. leration the red LED goes out c at full throttle the yellow LED goes out and the red LED shines d atslow braking both LEDs go out e at full brake the red LED shines The speed controller is now calibrated to your transmitter 6 Power Programs Overv The CS Rocket Competition Brushless comes with 9 power programs which can be selected for different types of RC Cars and different handling characteristics The setting is done with the setup key and the throttle trigger of the transmitter By moving the throttle trigger to full throttle or full brake the program numbers will be increased and finally saved in the speed controller Hint Move the throttle trigger slowly and always to the end point The table on the next page shows the recommended use of the different programs CS s ecrn0me Section Modified soft Modified medium Modified race Modified aggressiv Modified Reverse after full breaking Modified Reverse after full stop Sport Max Punch High Speed Sport Medium Punch Super High Speed Sport Mega Punch Mega High Speed CS CS ELECTRONIC Motor Limit Re NiMH verse Lipo 48 8 4V o 4 8 8 4V 48 8 4V 48 6 0V 48 TEEN Auto Battery Cutt Off Automatic Lipo and 4 7 Cells Automatic Lipo and 4 7 Cells Automatic Lipo and 4 7 Cells Automatic Lipo and 4 7 Cells Automatic Lipo and 4 7 Cells Automatic Lipo and 4 7 Cells Automatic Lipo and
13. n starting braking E Brake MAX adjustable maximum braking power at full brake E Power acceleration curve selectable from soft linear aggressive for an optimized adjustment to track and style of driving E Automatic Drive adjustable minimum acceleration at throttle trigger neutral position E Low battery recocnition manual adjustable or automatic mode E Transmitter settings checking of the detailed transmitter signal of full throttle full brake and neutral 9 Diagnostics It can have several reasons if your CS Rocket Competition speed controller does not work properly First check all components connected to the speed controller to exclude other failure sources If you can not solve the problem we recommend to perform a reset to the factory settings before you send the speed controller for repair to us The following table can help you with the diagnostic CS CS ELECTRONMIC Diagnostic BoE O Oc O ccc Red LED off Battery voltage 4 8V Charge battery Car drives backwards Motor cables are mixed Connect the motor Yellow LED off Plugs dirty or faulty Clean plugs and check ae cables properly No sound connections Dirction of rotation of Red LED flashes 1x Battery voltage too Use battery with cor acceleration Controller is getting Drive train turns not Check and make it too hot free running smooth Red LED flahes 3x No Motor connected Connect brushless or Wrong gear ratio Use smaller pinion or Motor Controller swit
14. ng of the motor must be set to minimum if possible Finalizing the Programming l After the selection of the program the speed controller is ready for use Please note After each program selection the gear ratio has to be exactly adjuste and must be checked after a short running time with the tempera ture of the brushless motor It is sufficient to strongly grasp the motor with three fingers If you can hold the motor for appr 4 seconds tight it is o k If not the temperature is raised over 65 C In this case you have to change the gear ratio immediately by using a smaller pinion to avoid any serious damage or destruction of one of the components After a new speed controller transmitter setup you have to select the power program again If you do not reselect the power program the speed controller is using the power program 3 E 6 selectable Modified Programs graded driving profiles for different cars and tracks E 3 selectable Sport Stock Programs with adjustable motortiming more power and top speed for the serious racer Attention the timing of the motor must be set to minimum if possible E Power Programs can be changed quite simple selectable with the throttle trigger of the transmitter E Automatic recognition of sensor and sensorless motors no setup for different motors necessary E PDM Precice Digital Drive Mode Technology exact sensitive and con trollable driving feeling results in constant fast lap times
15. or are connected in any kind to such conditions Only components and spare parts recommended by CS ELECTRONIC may be used Use only suitable plugs original from CS ELECTRONIC Please be sure that your transmitter is working on a free frequency is switched on and the throttle trigger is in neutral position before connec ting the speed controller and using the model 12 Technical Data Operating voltage Number of cells NiMH NiCd Number of cells LiPo Constant current brushless M Shorttime current 10s Pulse current at 25 C Inner resistance at 20 C appr Voltage loss at 20A app Temperature protection Low voltage protection BEC Power Max BEC dissipation power Clock frequency Dimension in mm incl capacitor appr Weight without cables appr Weight with cable appr CS ss arcrmonc 4 8 84V 4 7 2 120 A 250A 800A 0 0004 Q 0 008 V yes automatic adjustable 5 8 V short time 4 A 2 5 W 2 4 8 16 kHz 50x31x27 60g 95g 13 Accessories E C130201 Receiver cable 5 cm black C130202 Receiver cable 10 cm C130203 Receiver cable 20 cm C130204 Sensor cable 11 cm black for CS LRP GM Novak C130205 Sensor cable 20 cm black for CS LRP GM Novak C130206 Silicone cable Megaflex 11AWG black 4 0 mm 1m C130207 Silicone cable Megaflex 12AWG black 2 5 mm 1m C130208 CS Rocket Competition Interface with USB Adapter C130209 Cooling fan for CS Rocket Competition 30x30x6 incl 4 x sc
16. rews M2 5x8 Sensor cable adapter 14 24 Month Guarantee CS ELECTRONIC GmbH Johann Karg Str 30 D 85540 Haar b M nchen Germany guarantees this product for a period of 24 months from date of purchase This guarantee applies only to such material of operational defects which are present at the time of purchase Damages due to wear overloading incompetent handling are not covered by this guarantee The users legal rights and claims under guarantee are not affected by this guarantee Please check the product carefully for defects before you make a claim or send the item back to us since we are obliged to make a charge of 15 EUR if the product is found free of faults We can opnly handle a guarantee if the used motor is also send to us together with a detailed description of the failure including the used gear ratio and the used battery C130210 11 15 Service Returns Freight collect can not be accepted Please inform us about your complete address for question we maybe will have Please do not forget to include your telephone number and if existent your email address as well as your mobile number If you are a registered dealer of us please give us your customer code CS ELECTRONIC GmbH Johann Karg Str 30 D 85540 Haar b M nchen Tel 49 89 436 302 99 0 E Mail service cs electronic com In case of questions you can call or email us 16 CE Conformity Declaration We hereby declare that the following produc
17. scccsccccsccecccccsccscccscssscesecs 12 16 CE Conformity Declaration cccsscssccesecesccsccesecescceees 12 17 Environnemental protection notes ccsccsscsecssccsccscees 12 1 Dear Customer congratulations for buying your new digital CS Rocket Competition Brushless speed controller for brushless motors from CS ELECTRONIC You can be sure having purchased a product which was developed on the basis of the newest technical knowledge and constructed as well as optimized for the use in RC Cars We have realized several pioneering technologies in this product and are proud to present to you a intelligent high performance speed controller which has outstanding features in performance function ality and safety 2 Range of Application The CS Rocket Competition Brushleee Speed Controller is conceived for 1 10 RC cars with an operating voltage from 4 8 V to 8 4 V It can be used with all current brushless motors with or without sensor in the 540 size N 3 Installation IEN ThE Bie AA The speed controller must be placed in a cool and crash protected area in the car For fastening the speed controller use only two small stripes of double sided adhesive tape in a way that not the complete cooling area of the bottom is covered The receiver as well as the receiver antenna must have a distance of more than 3 cm to the speed controller Current carrying battery or motor cables should not be near
18. t CS Rocket Competition Best Nr C130200 conforms with the essential protective requirements as laid down in the directive for harmonizing the statutory directives of the mem ber states concerning electro magnetic interference 2004 108 CE and the low voltage guideline LVD 2006 95 CE This product has been tested for electro magnetic interference in accordance with the following norms EN61000 6 1 EN61000 6 3 12 CS ELECTRONIC This declaration was produced by CS ELECTRONIC GmbH Johann Karg Strasse 30 85540 Haar bei Munchen and is valid for the manufacturer importer of the product AM Geshe Norbert Forster 85540 Haar 30 01 2009 17 Environmental Protection Notes When this product comes to the end of its useful life you must not dispose it in the ordinary domestic waste The correct method of disposal is to take it to your local collection point for recycling electrical and electronic equipment Individual markings indicate which material can be recycled You make an important contribution to the protection of our common en vironment by recycling the basic materials or recycling redundant materials in other ways Remove batteries from your device and dispose them at your local collection point for batteries In case of RC models you have to remove electronic parts like servos receivers or speed controllers from the product and these parts must be disposed of with a corresponding collec tion point for electronic s
19. the antenna Avoid direct contact of the antenna to graphite or metal parts To avoid any interference problems guide the antenna on the direct way to the top of the car and do not coil up the antenna If necessary the antenna can be shortened to appr 35 cm in length Sufficient cooling openings in the body as well as cases free of dust or dirt increase the efficiency and the life time of electronic components CS ss arcmonc 4 Connection of the Compor The CS Rocket Competition is factory equipped with 10 AWG power cables for the connection to the battery Please use only suitable high current plugs i e C180712 und C180713 and pay attention to the polarity and A short circuit or a wrong polarity results in a serious damage of the speed controller The connection to the motor is done with 12 AWG power cables marked with A B and C These can be soldered directly to the connections of the motor To change the direction of rotation just exchange two of the three motor cables On Off Switch N A Bricen Receiver YX i K Setup Ue A it Orange motor oy A P Sm za Yellow motor WC lt lt m m HEE WN _ Blue motor Sensor ag USB Red Battery Black Battery AL CS ss arcrmonc Receiver connection First you connect the receiver cable BEC with the white three pole plug of your CS Rocket Seppdcon trollers Guide strips on the
Download Pdf Manuals
Related Search