EX8 manual
Contents
1. Xpr a Visual Plus Corporation Company EXO User Manual Ver 1 0 www visual plus com Xp m EX8 User Manual v1 0 Corporation Company EX8 manual ver1 0 Power supply important issue Use separate power supply when ever is possible one for EX8 and Reader and another for door lock This way electrical isolation between lock and EX8 protect the EX8 from any electrical noise generated by lock or damages caused by improper or damaged cabling of the lock Single power supply for EX8 and lock can be used if it has been made for this purpose If single power supply is to be used it must be tested by installer along with door lock before installation All locks do not have same electrical characteristics so the test must be done with lock that will be mounted at user site Keep power supply unit as close as possible to EX8 If longer distances are unavoidable use screened cables for 12V supply line Product concept The EX8 is used in a combination with fingerprint reader making standalone biometric access system Fingerprint Reader i Ge x E Aom b e QU fan Door Magnet AM Wee cn E y Exit Button UNSECURED AREA SECURED AREA Fig 1 Typical application www visual plus com 2 xpr a Visual Plus Corporation Company EX8 Controller EX8 User Manual v1 0 Housing 43B 3 B x 30 CSK z MA CT El un LEE il QUE i rH M3 x 6mm2. eoo O Enter security level 1 normal S _ 2 secure 3 more secure eoo www visual plus com 10 xpr au EX8 User Manual v1 0 Programming flowchart Enter Master PIN B default 000 B Three small beeps Error Beep RED Led blinks Validation OK Short Long beep OK Beep eeo U Change Relay 1 Relay 2 Assign Sensor Delete Delete Enroll User Master PIN Time Time Relays Settings All Users User O0 O0 eoo O 0 000 0000 000 01 99 seconds Enter User Number Press or Security Press 001 999 000 00 ON OFF Mode 2 999 000 00o 1 for Out1 OR 0 to 7 1 normal Enter NEW PIN s ps ne 0 ii 2 secure 1 to 8 sensitive digits 12 cn mor i secure 0 for neither sensitive Orange Orange LED on LED on Biometry Biometry Reader is Reader is blinking t blinking Green Orange LED on LED on EX8is EX8is blinking blinking Present finger ile cies Press A to validate Wait for 3 sec and OK beep from EX8 Three Back one level Validation OK beeps see Error Beep semaphore No Yes Short Long beep OK Beep To exit the menu Press B until the three LED s are OFF www visual plus com 11 xpr C
3. Close jumper J1 Turn ON the power supply Yellow LED will blink and buzzer will sound Open jumper J1 Master password is reset to default 000 Change master PIN code change Master PIN XXX to YYY XXX Enter master password XXXL ooo B Enter main menu eeo 0 Enter submenu 0 Enroll user ooo 000 Enter user number 000 eoo YYY Enter new password YYY SSS S o A Conf ent B Exitprogramming 000 To change master PIN from 000 to 123 000 B 0 000 123 A B Enroll a User User number ZZZ Finger F XXX Enter master password XX 000 B ZA Entermainmenu eeo 0 J Enter submenu 0 Enroll user 000 Select user number 001 999 oe0 1 Selectfingert 000 _Present the finger 1 on the reader Enrol Enroll done oe0 2 J Selecfingr2 00 Presentthefinger2onthereader Enrol Wait for OK beep Enmoldoe oeo B gt J Back to menu 0 ooo B JAdb Back to main menu eeo B ZJA Exit programming ooo To enroll User 001 with Master PIN 000 000 B 0 001 1 present finger wait for OK beep 2 wait for OK beep B B B Set user PIN User number ZZZ PIN PPPPP XXX Enter master password XXX 0o000 B Enter mainmenu X J J
4. security screw Readers Recommended position BioXr www visual plus com 3 xpr a Visual Plus Corporation Company EX8 User Manual v1 0 BioC Bioln www visual plus com 4 xpr a Visual Plus Corporation Company EX8 overview EX8 User Manual v1 0 Terminals side Terminal side Terminal 12V DC Power supply 12V Power supply OV Exit button Gnd_PB A GND D1 Gnd 1 1 Tamp Tamp m Com 2 NC Com 1 Red LED Blinking Error ON Reader not found ON Relay 1 activated ON Relay 2 activated e e e 99 s 9 n L2 3 L www visual plus com 5 xpr Company EX8 User Manual v1 0 Connections Readers EX8 BioC Wire color Name EX8 BioXr N D 5 D 6 Dt B jlj8 B J EX8 Bioln Terminal 12Vout 8 t2V p 3 DODA A 1 A 1 Bo Violet B Connecting reader with Cat5 network cable example Brown White DO Orange White B 2 JB Maximum cable length www visual plus com 6 XP Corporation Company Door control Door strike fail safe Electromagnetic lock fail open Disk Ceramic or Polyester capacitor 00lyF IN4007 Disk Ceramic Or Polyester capacitor www visual plus com 7 xpr Company EX8 User Manual v1 0 Programming Master PIN reset Turn OFF the power supply
5. with smooth cloth or towel Do not let children touch the device without supervision Note that if the sensor is cleaned by detergent benzene or thinner surface is damaged and fingerprint can t be entered www visual plus com 12 xpr Company EX8 User Manual v1 0 Technical specification EX8 BioXr EX8 BioC EX8 Bioln 999 Users 2 templates per user 1 PIN code per user Reader dimensions 132 x 86 x 32 90 x 50 x 25 151 x 90 x 53 HxWxD in mm Reader weight g IP65 IP54 IP54 Reader protection class Indoor use Indoor use Indoor use Power supply 12V DC 11 14 V DC Relay outputs Exit button Current consumption 250mA max without door lock Recommended 0 40 C Temperature Range 20 50 C Extended temperature rane Human contact with sensor at extreme temperatures not g recommended 30sec lockout after 16 invalid fingers or PIN codes Users capacity 999 Users 2 templates per user Models may vary www visual plus com 13 EX8 User Manual v1 0 Users register Recommended fingers are A B E F G J EQ 2 AQ Do not write in this page make copy i H9 eR y S P i hi gt UL 4 J User PIN Finger 1 Finger 2 Relays S E LLL LLL www visual plus com 14
6. 99 ae A Confirmentry eo Bo Exit programming 000 To delete User 123 with Master PIN 000 000 B 9 123 A B Delete all users XXX Enter master password XXX ooo Entermanmenu owo To delete all users with Master PIN 000 000 B 8 999 A B B 8 eo00 999 Enter delete all command D eeo B _ 000 www visual plus com 9 xpr Company EX8 User Manual v1 0 Assign relays to a User Action LED status Enter master password XXX Enter main menu B Enter submenu 3 Assign relays aZ ZZZ Enter user number 600 eeo oeo oeo0 Enter output combination R 0 Disable user User is not deleted 1 Relay1 only 2 Relay2 only 3 Relay1 and Relay2 A eeo o00 A B Exit programming O To assign Relay1 to User 123 with Master PIN 000 000 B 3 123 1 A B Fingerprint sensor sensitivity setup _XXX Enter master password XXX B X Entrmanmen tt 7 Enter submenu 7 Sensor setup eoo 1 Enter sensitivity setup menu eoo S Enter sensitivity S 0 7 7 most sensitive A Confimenty tw B Exit programming 000 To set sensor to most sensitive with Master PIN 000 000 B 7 1 7 A B Fingerprint sensor security setup Bo Exitprogramming To set sensor to normal security level with Master PIN 000 000 B 7 2 1 A B eo0
7. J J ee O Enter submenu 0 Enroll user ooo ZZZ Select user number 001 999 oeo 3 Select user PIN menu oee Enter user PIN must be 5 digits 00000 99999 LA Confimmenty le B Back to menu 0 000 B Back to main menu eeo B JjExtprorammnng _ooo To assign PIN 88888 to User 123 with Master PIN 000 000 B 0 123 3 88888 A B B B www visual plus com 8 xpr Company EX8 User Manual v1 0 Set Relay1 open time Action LED status o00 Enter master password XXX Enter main menu Enter submenu 1 Relay 1 time B eeo eoo Enter open time TT T 0 toggle mode 1 99 timed 1 99 seconds Confirm entry 1 1 eeo 000 T Confirm entry B Exiprogramming To set Relay1 open time to 3 seconds with Master PIN 000 000 B 1 03 A B Set Relay2 open time XXX Enter master password XXX ooo B Enter mainmenu Ct 2 Enter submenu 2 Relay2 time oeo mo Enter open time TT m TT 0 toggle mode 1 99 timed 1 99 seconds A Confimentry amp 3 2 J owo B Exit programming O00 To set Relay2 open time to 3 seconds with Master PIN 000 000 B 2 03 A B Delete user XXX Enter master password XXX Bo Enter main menu eo 9 Enter submenu 9 Delete user eo Enter user number ZZZ 001 9
8. ompany EX8 User Manual v1 0 Enrollment E aa I A M j gt E Enrollment area Correct enrollment Incorrect enrollment El h FT e E _ E __ i al imei Problem Solution Check main AC power No power supply Power supply unit Replace fuse F1 On powering the system at the EX8 red Novconmmunicaton bern Check cable terminals A and B LED stays ON while EX8 and reader Replace reader yellow LED blinks every Replace EX8 30 seconds If green LED at EX8 is ON Check lock power supply Reader authorize the ARE Ibl Check lock lock problem finger but door do not If green LED at EX8 is OFF Relay1 is not activated it is EX8 problem open Assign relays to user Check DO and D1 connections Clean the sensor do not use Dirty or damaged sensor abrasive cleaning solutions T User have too smooth Increase sensor sensitivity Finger is damaged EX8 reset when door ER cion Replace power supply unit or use lock is activated P PPly separate supply for lock Safety precautions Do not install the device in a place subject to direct sun light without protective cover Do not install the device and cabling close to a source of strong electro magnetic fields like radio transmitting antenna Do not place the device near or above heating equipments If cleaning do not spray or splash water or other cleaning liquids but wipe it out
Download Pdf Manuals
Related Search