Home

User Manual UM EN FL WLAN 5100 - Digi-Key

Contents

1. Monitoring Agent 687407022 Figure 6 1 Schematic view of SNMP 94 PHOENIX CONTACT 7191_en_03 Setting the system time and using SNTP 7 1 2 Supported MIBs and SNMP versions The device supports SNMP Versions V2 and V3 The device supports the following MIBs MIB II and the PXC WLAN5100 MIB The full complement of MIB files can be found at www phoenixcontact com or MIBs can be downloaded under Help amp Documentation in web based management for the device Up to ten trap receivers can be configured 7 2 Setting the system time and using SNTP 7 2 1 General information on SNTP The Simple Network Time Protocol SNTP is defined in RFC 4330 SNTP clients in automation technology and is used to synchronize the internal system time with any NTP server which represents the timer i e the universal time The aim is to synchronize all the components in a network with the universal time and to thereby create a uniform time base Time synchronization provides valuable assistance when evaluating error and event logs as the use of time synchronization in various network components enables events to be assigned and analyzed more easily
2. Unless otherwise expressly stated all information provided in this user manual always applies to both the FL WLAN 5100 and the FL WLAN 5101 1 1 General description Compact wireless access point client with the following properties Operation as a WLAN access point repeater or client Supports WLAN 802 11 standards a b g n Operation in the ISM band at 2 4 GHz frequency or in the 5 GHz band P20 degree of protection Connections COMBICON for supply voltage 10 36 V DC 2 x RJ45 ports for LAN Configuration via WBM SNMP and CLI via SSH Telnet Security functions 802 11i WPA2 WPA PSK TKIP AES Connections for three antennas MiMo technology connection method RSMA not supplied as standard Figure 1 1 FL WLAN AP 5100 8 PHOENIX CONTACT 7191 en 03 Technical description 1 2 FL WLAN 510x country registrations 1 2 1 FL WLAN 5100 The FL WLAN 5100 is a WLAN device with access point and client functionality The device uses the WLAN standard in the license free 2 4 GHz and 5 GHz bands which are free of charge The device meets all the requirements of R amp TTE directive 1999 5 EC Europe EMC according to EN 61000 6 2 2005 Safety according to EN 60950 1 2006 11 Health according to EN 50371 EN301 893 V1 5 1 5 GHz EN 300 328 V1 7 1 2 4 GHz EN 301 489 01 V1 8 1 and EN 301 489 17 V2 1 1 Depending on the maximum possible transmission p
3. Passkey In this field encryption for Machine Admin access is entered The type of encryption always corresponds to that specified in access point mode It is configured under WLAN Security mode 8 to 63 characters may be used Letters numbers and the following characters are permitted amp _ lt gt Grant access to IP Machine admin access via the WLAN interface second SSID of the WLAN 510x enables the user to access exactly one device in the connected network This device is specified via its IP address This address is entered under Grant access to IP The IP addresses under Grant access to IP must be in the same address area as the WLAN 510x See Network configuration FL WLAN 5100 Connected clients la DE ge Machine admin configuration Second SSID MachineAdmin Passkey PxC_MachineAdmin IV Show cleartext passphrase Grant access to IP 192 168 0 21 FL WLAN 5100 Information Help amp documentation Device status Interface status Alarm amp events Connected devices Configuration Quick setup Network WLAN Advanced WLAN Serice System Local events Network even Diagnostics Channel allocation Copa by Piori CortetGmbHECo KG mdoter Figure 3 7 The required settings for maintenance access connection can be entered in the Machine admin configuration menu 7191_en_03 PHOENIX CONTACT 53 FL WLAN 510x 3 8 PROF
4. Figure 5 2 Display of the current signal strength as a bar graph 84 PHOENIX CONTACT 7191_en_03 Diagnostics 5 2 Diagnostics of WLAN channel assignment on the access point If the FL WLAN 510x is in access point mode it is possible to detect other WLAN networks that are within range The WLAN channels used and the number of networks per channel are represented in a graphic In this way you can find a free channel for your own WLAN network for example In access point mode the WLAN networks that are within range are displayed in the Diagnostics Channel Allocation menu when you click on Scan PHCEN FL WLAN 5100 Connected Clients X gE anne cation Scan WLAN channels 2 4 GHz Channels FL WLAN 5100 this device Information Help amp Documentation Device Status Interface Status Alarm amp Events Connected Devices Configuration Quick Setup Network WLAN Advanced WLAN Cluster Configuration Service System Local Events Network Events Diagnostics Channel Allocation by Phoe at CortactGmbH amp Co KG and Otter other devices i 2 3 4 5 6 Zi 8 9 i0 11 12 13 5 GHz Channels 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140 Figure 5 3 Display of WLAN channel assignment on the access point 7191_en_03 PHOENIX CONTACT 85 FL WLAN 510x 86 PHOEN
5. Reset Device The device is restarted Existing WLAN connections are interrupted Username Administrator name Administrator password It is recommended that you enter a new password to prevent any manipulation of the device The new password must be between 8 and 14 characters long The new password is not activated until you log out and log back in again Retype password Retype the new password you wish to use Security context Open the window for configuring security certificates here Security context pop up window Upload certificate Choose whether to upload the safety certificate via TFTP or HTTP Direction Download WLAN device to local PC host Upload local PC host to WLAN device TFTP server IP address In the case of TFTP the file name and path of the TFTP server must be specified here Generate new Generate a new certificate SSH hostkey Host key for the SSH session 78 PHOENIX CONTACT 7191 en 03 Menu functions Table 4 1 Parameter list for Information page Designation Description Device name Enter the device name here that will be displayed in the web interface under Device status Device description Enter the description here that will be displayed in the web interface under Device status Physical location Enter the location here that will be displayed in the web interfa
6. 3 7 4 Operating mode machine admin In Machine Admin mode a network device can be accessed via WLAN using a panel PC or smart phone A second SSID which enables password protected access to exactly one device in the network is assigned for this access During configuration this device is specified by entering its IP address This mode is intended for maintenance access of a service technician for example who should deliberately not be able to access the entire network In parallel the entire network can be accessed password protected via the other SSID of normal access point mode 3 7 4 1 Configuration of Machine Admin mode When using Machine Admin mode PROFINET assistance mode cannot be enabled Machine Admin mode is activated on the web interface under WLAN Operating mode When selecting Machine Admin mode Access Point mode automatically runs in parallel The network via the access point and the connected network are therefore still available via the SSID specified under WLAN In addition restricted access to a specific network device is enabled using a different SSID This access is configured under Machine admin configuration This menu item is shown in the menu on the left after selecting Machine Admin mode FL WLAN 5100 contact Connected clients WLAN configuration Basic settings Activate WLAN interface 7
7. Lii nis B2 Figure 2 4 Removing the module from the DIN rail 2 1 2 3 Housing dimensions 109 ra gt A d J Y E 115 Figure 2 5 Housing dimensions with protruding parts in mm 7191 en 03 PHOENIX CONTACT 15 FL WLAN 510x 2 1 2 4 Wall mounting 1 Preferably use the mounting position illustrated in the following graphic The FL WLAN 5100 PA mounting kit Order No 2701092 can be used to mount the device ona wall Figure 2 6 Securing the mounting kit Use the two screws provided to secure the device to the base plate The two 4 5 mm bore holes can be used for mounting 2 1 2 5 Dimensions of the mounting kit and drill hole template 64 a 1 ENS y T iP 8 t JJ Tor D M 9 2 Figure 2 7 Dimensions of the mounting kit and drill hole template in mm 16 PHOENIX CONTACT 7191 en 03 Mounting 2 1 2 6 Mounting in the IP65 housing Phoenix Contact offers an IP65 housing FL RUGGED BOX OMNI 1 specifically for use in conjunction with the FL WLAN 510x Three omnidirectional antennas dual band 2 4 GHz and 5 GHz are supplied as standard with the housing They are screwed directly onto the housing Also included a
8. Indoor 8 channels automatically indoor 16 channels automatically The system automatically selects the channels Dynamic Frequency Selection DFS In doing so the connection may be interrupted during a channel switchover or in the event of radar detection Operation outdoors If your application is located outdoors the checkmark must be deselected from Indoor In Outdoor mode the wireless channel is automatically selected in the system Dynamic Frequency Selection DFS In doing so the connection may be interrupted for at least one minute during a channel switchover 1 NOTE This operating mode is prescribed by law within the EU for outdoor operation must be used 34 PHOENIX CONTACT 7191_en_03 Startup and configuration CE Encryption WLAN Security WPA2 PSK AES offers the highest security standard in encryption WPA2 EAP for use in enterprise IT environments with central authentication can be defined in the WLAN menu WPA PSK TKIP is available as an alternative Other encryption options are available in the WLAN menu or via the CLI interface We strongly recommend using secure encryption in order to protect your network against unauthorized access Where possible use WPA2 with AES NOTE If you select WPA TKIP rather than high data rates WLAN standard 802 11n prescribes the use of 54 Mbps maximum In orderto reach full data throughput under WLAN 802 11n WP
9. WLAN 5100 UM EN FL WLAN 5100 User manual UM EN FL WLAN 5100 OGD OO GD GD OGD OO OD Lions INSPIRING INNOVATIONS User manual UM EN FL WLAN 5100 2013 06 05 Designation UM EN FL WLAN 5100 Revision 04 Order No This user manual is valid for Designation FL WLAN 5100 FL WLAN 5101 Revision Order No 2700718 2701093 PHOENIX CONTACT 7191 en 04 Internet Subsidiaries Published by Please observe the following notes User group of this manual The use of products described in this manual is oriented exclusively to qualified electricians or persons instructed by them who are familiar with applicable standards and other regula tions regarding electrical engineering and in particular the relevant safety concepts Explanation of symbols used and signal words hazards Obey all safety measures that follow this symbol to avoid possible in This is the safety alert symbol It is used to alert you to potential personal injury jury or death There are three different categories of personal injury that are indicated with a signal word DANGER This indicates a hazardous situation which if not avoided will re sult in death or serious injury WARNING This indicates a hazardous situation which if not avoided could result in death or serious injury CAUTION This indicates a hazardous situation which if not avoided could result in minor or moderate injury This symbol togeth
10. 1 1 General description niic dta eese ivo esa PEE 8 1 2 FL WLAN 510x country registrations eseeee e 9 1 2 1 EEWEAN S100 9 1 2 2 FE WEAN 5101 up P aer Re i bee ene 9 1 3 Firmware ses P EE 12 2 science EN 13 2 1 Connections and operating elements sese 13 2 1 1 Electrical connection 14 2 1 2 MOUNTING eiii Sete deter obtentu eel ett ves Pte 14 O gt oSnmipandcontiqurationk eia pague uum B mes Ue ae 19 3 1 Status and diagnostic indicators sse 20 3 1 1 Meaning of the LAN1 2 indicators 21 3 1 2 Meaning of the LEDs as signal quality indicators in client mode 21 3 2 Configuration using the MODE button esseeeeneeem een 21 3 2 1 General sequence esssesssseeeee eene ennemis 22 3 2 2 Changing the firmware image using the MODE button 23 3 2 3 acetone ite eee e BR peed note Ten 24 3 2 4 Assigning the IP address via BootP with IPAssign 25 3 2 5 IP address assignment using IPAssign exe 25 3 2 6 Using the digital input and output see 28 3 8 Startup via the web interface ssssssssseeee
11. Configuration Quick Setup Network WLAN Advanced WLAN Service System Diagnostics System Events Copyright by Phoenix Contact Gmb amp Co KG and Omer Figure 3 6 Login web page On the web page you can set all the necessary configurations for a standard WLAN network Language selection First select the language for user management the web page interface The help text displayed when you move the mouse cursor over the is shown in the selected language IP address assignment Static The static IP address subnet mask and gateway address can be set here 7191_en_03 PHOENIX CONTACT 31 FL WLAN 510x BootP during initial startup the device transmits BootP requests without interruption until it receives a valid IP address As soon as it receives a valid IP address the device stops sending BootP requests After receiving a BootP reply the device no longer sends BootP requests Following a restart a device that was previously configured sends three BootP requests if these requests are not answered the device starts with the IP address that was last assigned via BootP After the default settings are restored the device sends BootP requests until they are answered DHCP dynamic request for an IP address from a DHCP Dynamic Host Configuration Protocol server Country setting Under Country select the country in which the device is operated By selecting the country regulatory features in ter
12. You will then only be able to configure the parameters that are permissible for this specific country Operating Mode Access point implements a WLAN wireless network for wirelessly connecting WLAN compatible devices to an Ethernet network Client FTB supports the wireless connection of Ethernet devices to an Ethernet network via a WLAN wireless network Fully Transparent Bridge FTB mode supports Layer 2 transparent communication with multiple devices behind the WLAN client Other client modes are available in the WLAN menu Network SSID The SSID is the network ID via which clients are assigned to the access points It can be a maximum of 32 characters long Letters numbers and the following characters are permitted amp _ lt gt WLAN Band Selection of the frequency band Other operating modes according to IEEE 802 11 are available in the Advanced WLAN menu 7191 en 03 PHOENIX CONTACT 71 FL WLAN 510x Table 4 1 Parameter list for Information page Designation Description Channel Channel selection possible channel selection depends on the setting made under WLAN Band Indoor Ch36 Ch48 4 channels can be freely selected Indoor 8 channels automatically indoor 16 channels automatically the system selects the channels automatically DFS The connection may be interrupted during a channel switchover Automatic The device automatically
13. 1 1b g 5 GHz up to 9 channels according to 802 11a For 802 11a 20 dBm at 6 Mbps 18 dBm at 54 Mbps For 802 11b 19 dBm For 802 11g 19 dBm at 6 Mbps 18 dBm at 54 Mbps For 802 11an max 19 dBm at MCS 0 15 dBm at MCS 15 For 802 11gn max 18 dBm at MCS 0 15 dBm at MCS 15 For 802 1 1a 84 dBm at 54 Mbps 97 dBm at 6 Mbps For 802 11b 97 dBm at 11 Mbps 97 dBm at 1 Mbps For 802 119 84 dBm at 54 Mbps 97 dBm at 6 Mbps For 802 11n 76 dBm at MCS15 97 dBm at MCSO 2 4 to 2 48 GHz IEEE 802 1 1b g 5 15 to 5 35 GHz 5 47 to 5 725 GHz IEEE 802 1 1a h 2 4 to 2 48 GHz IEEE 802 11b g 5 15 to 5 35 GHz 5 725 to 5 85 GHz IEEE 802 11a 802 11b DSSS 802 11 a g n OFDM Supports roaming in client mode 3 x RSMA connection no antennas supplied as standard 50 Ohm 1 gt 10 V DC to 36 VDC lt 5VDC 1 supply voltage minus 1 V 0 5 A maximum None WPA PSK and WPS2 PSK WPA PSK 802 1 1i with TKIP or AES CCMP WPA RADIUS with TKIP or AES CCMP WPA RADIUS and WPA2 RADIUS 25g when there is a half wave of 30 ms Operation 5g 10 500 Hz Class B Class a Contact discharge 6 kV Air discharge 8 kV 10 V m Criterion A 88 PHOENIX CONTACT 7191_en_03 Technical data Conformance with EMC directives for FL WLAN 5100 Conducted interference according to IEC 61000 4 6 Fast transients burst according to IEC 61000 4 4 Surge voltages according to IEC 61000 4 5 10 Vrms Criterion A Data lines
14. 1 kV Criterion B Power supply lines 0 5 kV Criterion B Data lines 2 2 kV asymmetrical Criterion B Power supply lines 2 2 kV symmetrical asymmetrical Criterion B Approvals for FL WLAN 5100 Compliance with the Safety of information technology equipment test specifications DIN EN 60950 VDE 0805 IEC 950 Differences between this version and previous versions of the user manual Rev 00 no differences initial version Rev 01 valid for firmware Version 1 50 or later Rev 02 smaller adaptations Rev 03 valid for firmware Version 1 60 or later 6 1 Ordering data Description Order designation Order No Access point ETSI approval FL WLAN 5100 2700718 Access point FCC approval only for use in the USA and Canada FL WLAN 5101 2701093 Mounting bracket panel adapter FL WLAN 5100 PA 2701092 SD memory card SD FLASH 512 MB 2988146 IP65 protective housing with three dual band antennas for 2 4 GHz and FL RUGGED BOX OMNI 1 2701430 5 GHz and three connecting cables access point not included plus a 144 mm long DIN rail Control box for rugged construction of wireless systems for industrial FL RUGGED BOX 2701204 applications IP65 25 x 18 x 13 cm polycarbonate material gray drilled including DIN rail plugs and screw connections without devices Control box set for constructing wireless systems for industrial FL RUGGED BOX OMNI 2 2701439 applications including three 2
15. 5 9 BB 2838490 coaxial signal interfaces Connection N connectors socket socket Vulcanizing sealing tape for external protection of adapters cable RAD TAPE SV 19 3 2903182 connections etc against the effects of weather roll length 3m COMBICON plug MC 1 5 4 ST 3 5 1840382 Gray RJ45 plug set for linear cable 2 pieces FL PLUG RJ45 GR 2 2744856 Green RJ45 plug set for crossed cable 2 pieces FL PLUG RJ45 GN 2 2744571 Assembly tool for RJ45 plugs FL CRIMPTOOL 2744869 Factory Manager startup diagnostics software FL SWT 2831044 Network monitoring with HMI SCADA systems FL SNMP OPC 2832166 SERVER Patchbox 8 x RJ45 CAT5e pre assembled can be retrofitted FL PBX8TX 2832496 Patchbox 6 x RJ45 CAT5e and 4 SC RJ glass pre assembled can be FL PBX 6TX 4FX 2832506 retrofitted Patch cable CAT5 pre assembled 0 3 m long 10 pieces FL CAT5 PATCH 0 3 2832250 Patch cable CAT5 pre assembled 0 5 m long 10 pieces FL CAT5 PATCH 0 5 2832263 Patch cable CAT5 pre assembled 1 0 m long 10 pieces FL CAT5 PATCH 1 0 2832276 Patch cable CAT5 pre assembled 1 5 m long 10 pieces FL CAT5 PATCH 1 5 2832221 Patch cable CAT5 pre assembled 2 0 m long 10 pieces FL CAT5 PATCH 2 0 2832289 Patch cable CAT5 pre assembled 3 0 m long 10 pieces FL CAT5 PATCH 3 0 2832292 Patch cable CAT5 pre assembled 5 0 m long 10 pieces FL CAT5 PATCH 5 0 2832580 Patch cable CAT5 pre assembled 7 5 m long 10 pieces FL CAT5 PATCH 7 5 2832616 Patch cable CAT5 pre assembled 1
16. CONTACT 69 FL WLAN 510x 4 1 Parameter list for the configuration Table 4 1 Parameter list for Information page Designation Description Help amp Documentation Documentation amp SD Card Documentation of the The latest documentation for the device can be device PDF downloaded here as a PDF file Device Description Zip ZIP file for the device description SNMP SGML SNMP SGML IP Assignment Tool The IP Assignment Tool can be downloaded from the device here It can be installed on a PC and used for IP address assignment Device Status Device Identification This area contains important static information regarding the WLAN device especially its hardware and firmware version System Status This area contains dynamic information regarding the WLAN device such as the system time operating time since the last voltage reset and the states of the digital inputs and outputs Interface Status Interface Status LAN This area contains information regarding the current settings and states of the LAN interfaces Interface Status WLAN This area contains information regarding the current settings and states of the WLAN interfaces Note on client mode Show RSS displays a bar graph for antenna alignment Alarm amp Events Alarm amp Events A chronologically ordered table overview displays the event messages of the device The complete log file can be down
17. Cluster Name Confirm with Apply PHEN FL WLAN 5100 Ri B amp DB Clustering Enabled n Cluster name test cluster FL WLAN 5100 Device Name IP Address MAC Address Band Mode Channel Output Pd FL WLAN 5100 192 168 0 101 00 A0 45 37 1F CC 2 4GHz 802 w 7 2 442GF v 17 dBm Information FL WLAN 5100 192 168 0 104 00 15 61 10 58 E2 2 4GHz 802 v 7 2 442GF v 17 dBm buda ee FL WLAN 5101 192 168 0 100 00 A0 45 EE EE 02 2 4GHz 802 7 2 442GF v 17 dBm Statue FL WLAN 5100 192 168 0 102 00 0 45 36 9 2 4GHz 802 7 2 442GF v 17 dBm Alarm amp Events Connected Devices Configuration Quick Setup Network WLAN Advanced WLAN Cluster Configuration Serice System Local Events Network Events Diagnostics Channel Allocation Copyright by Proen Contact GmbHECO KG and Omer Figure 3 9 Assigning the cluster name the table first shows the access point used for configuration by the user Click on Start to start searching for other FL WLAN 510x type access points on the cable side After completing the inquiry scan a list of available access points is displayed The access point used for configuration is displayed in the last row on a gray background The access points that will be added to the cluster are now selected in the last column Cluster Member s
18. M enable Operating mode Access Point x Access Paint o Client FTB FL WLAN 5100 Cliant 36B Network SSID Client MCB Hide SSID Repeater Country regulatory domain 2 Information WLAN band Help amp documentation Channel Pw Device status Interface status Output power 17 dBm Alarm amp events Connected devices WLAN security Configuration Quick setup Security mode wPA2 PSK AES SEN Passkey eee T Show cleartext passphrase Advanced WLAN Cluster configuration Service System Local events Network events Diagnostics Channel allocation Capi by CortctGmbHeCo HG avdotier Figure 3 6 Machine Admin mode can be selected on the WLAN page 52 PHOENIX CONTACT 7191 en 03 Startup and configuration Second SSID Open the Machine admin configuration page First enter a network name in the Second SSID field This name is used to identify the administrator network The name is displayed on the WLAN page and can be selected by the termination device to be connected Typically the termination device is a tablet PC smart phone or notebook If your termination device is to be assigned an IP address via the WLAN 510x the DHCP server must be configured first see Section DHCP server on page 64 Usually devices like tablet PCs or smart phones expect temporary IP address assignment via a DHCP server
19. Other Revert Apply Apply amp Save Figure 3 8 PROFINET assistance mode should be enabled in PROFINET applications The following settings are activated in PROFINET assistance mode 1 IPaddress assignment is via DCP 2 PROFINET data is transmitted with top priority 54 PHOENIX CONTACT 7191 en 03 Startup and configuration 3 8 1 2 PROFINET prioritization In PROFINET assistance mode prioritization based on the PROFINET Ethertype is performed in addition to prioritization based on the VLAN tag and 802 11e Here PROFINET packets are transmitted with top priority over all other Ethernet packets via the WLAN interface strict prioritization The remaining traffic not labeled as PROFINET is limited to a maximum data throughput of 10 Mbps Reliable PROFINET communication is therefore also ensured in the event of a higher broadcast and multicast load as well as other high priority data on the Ethernet interface When setting the PLC please observe that the PROFINET update time must also be adjusted according to the number of PROFINET devices The more PROFINET devices used in the WLAN network the higher the required PROFINET update time 7191_en_03 PHOENIX CONTACT 55 FL WLAN 510x ie me ee 3 9 Wi Fi Protected Setup WPS Wi Fi Protected Setup WPS is a standard developed by the Wi Fi Alliance intended to help users easily set up a wireless network including the encryptio
20. Passkey 7 eeeeeeee L Show cleartext passphrase Administrator Password Retype Password Figure 3 13 Cluster information in WBM An access point that is part of a cluster indicates this in the web interface as well as the following cluster information of the access point MAC address Paddress The following information is exchanged within a cluster WLAN SSID Security settings access control list MAC address filter User names and passwords QoS settings WLAN settings The following information can also be viewed within a cluster Diagnostic information Connected clients 62 PHOENIX CONTACT 7191_en_03 Startup and configuration 3 11 3 Properties of cluster management The members of a cluster have the same cluster name and the same administrator password The cluster configuration can be changed by any cluster member The members of the cluster automatically load the latest configuration IP addresses are not assigned via cluster management Up to 20 access points can belong to a cluster Individual settings can only be made to cluster members if these particular members can be accessed The individual settings of specific devices are not saved in the cluster and therefore in the case of device replacement cannot be transferred to the replaced device Devices that were offline when a change was made to the configuration in the
21. SSH password protected 4180 Via MINI COMBICON maximum conductor cross section 1 5 mm 24 V DC PELV 10 V DC to 36 V DC 200 mA Ill IEC 61140 EN 61140 VDE 0140 1 2 RJ45 socket on the device 10 100 Mbps 100m BootP 3 x RSMA female 7191 en 03 PHOENIX CONTACT 87 FL WLAN 510x Interfaces Wireless standards for FL WLAN 5100 Wireless standards for FL WLAN 5101 Maximum transmission power at the RSMA connection Receiver sensitivity at the RSMA connection Frequency range for FL WLAN 5100 Frequency range for FL WLAN 5101 Modulation method Roaming Antennas Impedance Digital input Number Logic 1 voltage level Logic 0 voltage level Digital output Number Output voltage Output current Filter encryption Encryption authentication Mechanical tests Shock test according to DIN EN 60068 2 29 Vibration resistance according to DIN EN 60068 2 6 Conformance with EMC directives for FL WLAN 5100 Noise emission according to EN 55022 Radio interference field strengths according to EN 55022 Electrostatic discharge ESD according to EN 61000 4 2 Electromagnetic fields according to IEC 61000 4 3 IEEE 802 1 1a b g h n Automatic or manual channel selection 2 4 GHz 13 channels according to 802 1 1b g 5 GHz up to 19 channels according to 802 11a according to standard 802 11h IEEE 802 1 1a b g h n Automatic or manual channel selection 2 4 GHz 11 channels according to 802
22. gain IP55 degree of protection 1 5 m cable length MCX 3 1 MCX connection male h v 360 85 opening angle Mounting material for wall mounting the omnidirectional antenna with RAD ANT VAN MKT 2885870 protection against vandalism Omnidirectional antenna 2 4 GHz 6 dBi linear vertical h v 360 20 RAD 2400 ANT OMNI 6 0 2903219 opening angle N female IP65 salt water resistant SW Dual band omnidirectional antenna with protection against vandalism RAD ISM 2459 ANT 2692526 IP68 protection frequency band gain 2 4 GHz up to 6 dBi 5 GHz up to FOOD 6 0 8 dBi EN 50155 temperature range 40 C to 80 C N f connection 1 m long adapter cable N m SMA m connection Panel antenna 2 4 5 GHz 9 dBi linear vertical N female IP67 ANT DIR 2459 01 2701186 Panel antenna 5 GHz 9 dBi 45 dual slant h v 70 60 opening ANT DIR 5900 01 2701348 angle 2 x N female IP67 Omnidirectional antenna 5 GHz 5 dBi gain linear vertical polarization ANT OMNI 5900 01 2701347 h v 3607 25 opening angle N female IP64 Parabolic antenna IP65 protection 19 dBi gain linear vertical RAD ISM 2400 ANT PAR 2867885 N female connection 50 O impedance h v 17 11 opening angle 19 0 Panel antenna 5 GHz 18 dBi gain N female connection IP55 RAD ISM 5000 ANT PAR 5606613 18 N Parabolic antenna 5 GHz 22 dBi gain N female connection IP55 RAD ISM 5000 ANT PAR 5606174 22 N Adapter cable pigtail 50 cm N femal
23. itis protected against mechanical damage corrosion chemical stress and the effects of heat or UV radiation The same applies to the antenna which is connected to the cable and which functions as a cable termination The antenna must meet the requirements of EN 60079 0 with regard to housing and electrostatic discharge 7191 en 03 PHOENIX CONTACT 19 FL WLAN 510x e NOTE The device must only ever be operated when an antenna is present at the activated antenna connection The antenna connections can be deactivated under Advanced WLAN in the web interface Do not screw more than one omnidirectional antenna onto the device The distance of the antenna connectors has been optimized for installation in control cabinets and the use of antenna cables To ensure decoupling the distance between the antennas should be at least 80 mm A larger distance may improve the performance of the device This section describes a typical startup of the WLAN device as an access point or client using the Quick Setup feature A standard WLAN network can be established in this way For special applications and configuration further details can be found in Menu functions on page 69 3 1 e Status and diagnostic indicators e 0 Lo 58 Se Q MODE e A Figure 3 1 Status and diagnostic indicators 1 LEDs A B C and D indicate the relevant sta
24. not possible This device and its antenna s must not be co located or operation in conjunction with any other antenna or transmitter If this device is going to be operated in 5 15 5 25GHz frequency range it is restricted in indoor environment only FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body IC Statement This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B conforme la norme NMB 003 du Canada This device complies with Industry Canada license exempt RSS standard s Operation this subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device 10 PHOENIX CONTACT 7191 en 03 Technical description Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement For product available in the USA Canada marke
25. of functions that relate to the digital input can be activated simultaneously If you activate the Show status of WLAN interface function for the digital output the Status change via SNMP and Status change via WBM functions will be deactivated automatically The Show status of WLAN interface function sets the output to ON if a WLAN link is present Table 3 4 Function of the digital inputs outputs Function Digital input Digital output Status request via SNMP Yes always Yes always Status change via SNMP Yes via configuration Status request via WBM Yes always Yes always Status change via WBM Yes via configuration Send SNMP trap when input Yes via configuration is set Trigger WLAN roaming Yes via configuration Switch WLAN interface Yes via configuration on off Show status of WLAN Yes via configuration interface 3 3 Startup via the web interface 1 WBM of the device is optimized for Internet Explorer 8 0 or later 28 PHOENIX CONTACT 7191 en 03 Startup and configuration 3 3 1 General information in the web interface 3 3 1 1 There are a few icons at the top of the web page marked in red in the graphic below which provide an overview of important device functions Web interface icons FL WLAN 5100 PHENIX LLL D Quick Setup Web management language English Mi IP Address As
26. products e Enter the order number 2701094 or IPASSIGN in the search field for example The BootP IP addressing tool can be found under Configuration file e Double click on the IPAssign exe file e Inthe window that opens click on Run From the device e Set the device to mode 6 using the MODE button see Configuration using the MODE button on page 21 e Usinga browser go to IP address 192 168 0 254 In web based management you can start the program by double clicking on it under Help amp Documentation Step 2 IP Assignment Wizard For the device to send BootP requests you must switch the device back to BootP on the Quick setup IP address assignment web page The program opens and the start screen of the addressing tool appears The program is mostly in English for international purposes However the program buttons change according to the country specific settings 7191 en 03 PHOENIX CONTACT 25 FL WLAN 510x The start screen displays the IP address of the PC This helps when addressing the device in the following steps e Click on Next Step 3 IP Address Request Listener All devices sending a BootP request are listed in the window which opens These devices are waiting for a new IP address Phoenix Contact IP Assignment Tool IP Address Request Listener Please select a MAC Address The list box below displays all MAC Addresses that we have receiv
27. seen in the right hand column of the table The configuration is stored to the device as the latest configuration by clicking on the diskette icon Any parameter changes made to a device belonging to a cluster and saved will be automatically transferred to the other devices in the cluster However the parameters listed in the Cluster Configuration table can be configured individually Access points can be integrated into a cluster at a later time To do this enter the name of the existing cluster under Cluster in the Cluster Group Configuration window An inquiry scan is triggered by clicking on Start The new device appears in the list and can be added to the cluster via the checkbox under Cluster Member Save the configuration with Apply amp Save 7191 en 03 PHOENIX CONTACT 61 FL WLAN 510x 3 11 2 Identifying cluster relevant parameters in the web interface In cluster management the parameters of an access point marked with an in the web interface see red marking in Figure 3 13 on page 62 if the function was previously activated on the Cluster Configuration web page are transferred to the other access points in the cluster Country Regulatory confer Germany Operating Mode Accesspoint v Network SSID PxC WLAN Band 2 4GHz 802 11 b g n v Channel Channel 2 442GHz WLAN Security WPA2 PSK AES
28. selected as the Operating Mode and confirmed with Apply amp Save The SSID Security mode and Passkey are then entered and confirmed with Apply amp Save oraux FL WLAN 5100 connected Clients B 3 WLAN Configuration Basic settings Activate WLAN interface 1 enable Operating Mode Repeater vj M Indoor only Country Regulatory Domain Germany Disable 802 11d Country Domain Bayete ta Network SSID 7 CSCS Information Output power 7 17 dBm 2 Help amp Documentation Device Status Interface Status Alarm amp Events Connected Devices Configuration Quick Setup Network WLAN Advanced WLAN Cluster Configuration Service System Local Events Network Events Diagnostics Channel Allocation VP by Phoe al ContactGmbHSCo KG and Otter WLAN Security Security mode FWPA2 PSK Passkey ehem Gk Show cleartext passphrase Figure 3 3 Configuration of the repeater The WLAN repeater now scans for the corresponding SSID and establishes the connection The WLAN LED lights up blue after successful connection establishment The MAC address of the connected device and information regarding the connection quality are displayed in the Interface Status WLAN menu 50 PHOENIX CONTACT 7191_en_03 Startup and configuration 3 7 3 1 4 Number of devic
29. the purpose of technical progress The receipt of technical documentation in particular user documentation does not consti tute any further duty on the part of Phoenix Contact to furnish information on modifications to products and or technical documentation You are responsible to verify the suitability and intended use of the products in your specific application in particular with regard to observ ing the applicable standards and regulations All information made available in the technical data is supplied without any accompanying guarantee whether expressly mentioned im plied or tacitly assumed In general the provisions of the current standard Terms and Conditions of Phoenix Contact apply exclusively in particular as concerns any warranty liability This manual including all illustrations contained herein is copyright protected Any changes to the contents or the publication of extracts of this document is prohibited Phoenix Contact reserves the right to register its own intellectual property rights for the product identifications of Phoenix Contact products that are used here Registration of such intellectual property rights by third parties is prohibited Other product identifications may be afforded legal protection even where they may not be indicated as such PHOENIX CONTACT Table of contents Table of contents 1 Technical description na tede edu uit aea eere te iubet petu toe erase tes a due ad ay 8
30. to the configuration PC The FL WLAN 510x receives the IP address 192 168 0 254 24 PHOENIX CONTACT 7191_en_03 Startup and configuration 3 2 4 Assigning the IP address via BootP with IPAssign This section explains IP address assignment using the IP Assignment Tool Windows software IPAssign exe This software can be downloaded free or charge at hoenixcontact net catalog The tool can also be found under Help amp Documentation on the web page for the device where it can be started directly Notes for BootP During initial startup the device transmits BootP requests without interruption until it receives a valid IP address As soon as it receives a valid IP address the device stops sending BootP requests After receiving a BootP reply the device no longer sends BootP requests Following a restart a device that was previously configured sends three BootP requests if these requests are not answered the device starts with the IP address that was last assigned via BootP After the default settings are restored the device sends BootP requests until they are answered Requirements The device is connected to a computer using a Microsoft Windows operating system 3 2 5 IP address assignment using IPAssign exe Step 1 downloading and executing the program You can either load the tool from the Internet or from the device itself From the Internet e On the Internet select the link phoenixcontact net
31. 0 0 m long 10 pieces FL CAT5 PATCH 10 2832629 PHOENIX CONTACT GmbH amp Co KG Flachsmarktstr 8 32825 Blomberg If there are any problems that cannot be solved using this documentation please call our Germany 49 0 52 35 3 00 amp 49 0 52 35 3 4 12 00 9052 www phoenixcontact com 25 www phoenixcontact com Worldwide locations www phoenixcontact com salesnetwork HOTLINE hotline Gp 49 0 52 81 946 2888 7191_en_03 PHOENIX CONTACT 91 FL WLAN 510x 92 PHOENIX CONTACT 7191_en_03 7 Technical appendix 7 1 Simple Network Management Protocol SNMP 7 1 1 General function SNMP is a manufacturer independent standard for Ethernet management It defines commands for reading and writing information and defines formats for error and status messages SNMP is also a structured model that consists of agents their relevant Management Information Base MIB and a manager The manager is a software tool that is executed on a network management station The agents are located inside switches bus terminal modules routers and other devices that support SNMP The task of the agents is to collect and provide data in the MIB The manager regularly requests and displays this information The devices can be configured by writing data from the manager to the MIB In the event of an emergency the agents can also send messages traps directly to the manager All configuration modific
32. 0 cfg file on the SD card Save client configuration the device that is in access point mode can save the corresponding client configuration here The SD card can then be used to configure the client that corresponds to the access point Advanced configuration pop up window Upload certificate Upload certificate via HTTP select a file by clicking on Upload a file or drag the file over this button Alternatively the certificate can be uploaded via a TFTP server 7191_en_03 PHOENIX CONTACT 79 FL WLAN 510x Table 4 1 Parameter list for Information page Designation Description Direction Download from device to local PC host Upload from PC host to device TFTP server IP address Enter the TFTP server address Current configuration Download the configuration from the device by selecting the wlan_5100 cfg file Configuration name The active configuration can be assigned a name here Customer default configuration A customer specific configuration can be downloaded to the device or from the device here This configuration can also be activated via the MODE button Device independent configuration Local Events Local events digital input A configuration can be downloaded to the device or from the device here which only stores the general settings and not device specific data Status Current state of the digital input connect
33. 4 5 GHz IP65 omnidirectional antennas that can be directly screwed on with DIN rail plugs and screw connections with 100 240 V power supply unit without devices Control box set for constructing wireless systems for industrial FL RUGGED BOX DIR 1 2701440 applications including panel antenna and 3m antenna cable for 2 4 5 GHz IP65 with DIN rail plugs and screw connections with 100 240 V power supply unit without devices Omnidirectional antenna 2 4 GHz 5 GHz 2 5 5 dBi gain linear vertical ANT OMNI 2459 02 2701408 polarization 2 4 GHz h v 360 30 5 GHz h v 260 16 opening angle N male IP68 Omnidirectional antenna with protection against vandalism 2 4 GHz RAD ISM 2400 ANT VAN 2701358 3 dBigain IP55 protection 1 5 m cable length RSMA connection male 3 0 RSMA h v 3607 85 opening angle 7191 en 03 PHOENIX CONTACT FL WLAN 510x Description Order designation Order No Omnidirectional antenna 2 4 GHz 2 dBi linear vertical 1 5 m cable RAD ISM 2400 ANT OMNI 2701362 RSMA male IP65 50 O impedance 2 1 RSMA Omnidirectional antenna with protection against vandalism 2 4 GHz RAD ISM 2400 ANT VAN 2885867 3 dBi gain IP55 protection 1 5 m cable length SMA connection male 3 0 SMA h v 360 85 opening angle Omnidirectional antenna with protection against vandalism 2 4 GHz RAD ISM 2400 ANT VAN 2885702 3 dBi
34. A2 PSK AES encryption must be used Passkey Enter a key which will be used by the device during the initialization of WPA encryption Note for maximum security a random alphanumeric string up to 63 characters should be used Letters numbers and the following characters are permitted amp _ lt gt The password must contain at least eight characters Administrator Password The password for accessing the web interface is changed under Administrator Password and confirmed under Retype Password The change of password is applied when you log out and log back in again The change is only applied when you click on Apply To permanently save the change beyond a device restart click on Apply amp Save We strongly recommend that you change the administrator password the first time you use the device in order to avoid unauthorized access to the web interface 7191 en 03 PHOENIX CONTACT 35 FL WLAN 510x 3 4 2 Operation as a client In client FTB mode the device forms the wireless interface of a distributed device One or more WLAN clients can be connected to a WLAN access point PHCEN FL WLAN 5100 f 4X Y vy I Web management language English IP Address Assignment bootp z hide as Country Regulatory Domain Germany vj ing Information perating Mode Help amp Documentation Device Stat
35. Clients should therefore only be activated at the most extreme points of an NTP network Time synchronization is carried out at fixed synchronization intervals known as polling intervals The client receives a correction time by means of an SNTP server with the packet runtime for messages between the client and server being integrated in the time calculation in the client The local system time of the client is thus constantly corrected Synchronization in the NTP is carried out in Universal Time Coordinated UTC format The current system time is displayed as Universal Time Coordinates UTCs This means that the displayed system time corresponds to Greenwich Mean Time The system time and the UTC offset provide the current local time The device supports the use of the SNTP protocol only in client mode i e devices or other network components only ever receive a time from a time server but do not transmit their own times Each client synchronizes its system time with that of an SNTP server Time synchronization is carried out at fixed synchronization intervals Thelocal system time of the client is thus constantly corrected Synchronization is carried out in Universal Time Coordinated UTC format 7191 en 03 PHOENIX CONTACT 95 FL WLAN 510x The corresponding web page is located under Configuration Service System Time System Time Network time protocol disable Primary SNTP Se
36. ContectGmbHSCo bG ard Other Event SNMP Trap Remote Syslog Start of device o Ethernet link state changed O o Userinterface access changed Digital Input state changed o Error LED state changed M Configuration state changed O SD plug state changed 2 Figure 3 15 Possible system events that can be selected 66 PHOENIX CONTACT 7191_en_03 Startup and configuration 7191_en_03 PHOENIX CONTACT 67 FL WLAN 510x 68 PHOENIX CONTACT 7191_en_03 Menu functions 4 Menu functions The web interface is split into three main areas each containing several thematically structured web pages Area Information This area contains information on the product and the current device status You do not have to log in to access the web pages Area Configuration You can configure the device in this area For security reasons you must log in with a password before accessing the web pages Web page Quick Setup All the main parameters are grouped together on the Quick Setup web page in order to enable quick and easy configuration of a WLAN standard network or WLAN client adapter Area Diagnostics All information regarding the diagnostics of wireless connections can be found in this area Help On web pages a appears after each parameter When you place the mouse pointer over it information regarding the parameter is displayed in a flyout window 7191 en 03 PHOENIX
37. Ethernet switches to the access point on Layer 2 Operation as a fully transparent bridge is possible between the following devices FL WLAN 510x FL WLAN 510x FL WLAN 510x FL WLAN XX AP DAP 802 11 FL WLAN 510x FL WLAN 24 EC 802 11 Operation as a fully transparent bridge is not possible between the following devices FL WLAN 510x FL WLAN 24 AP 802 11 XDB FL WLAN 24 EC 802 11 FL WLAN 24 AP 802 11 XDB FL WLAN 24 AP 802 11 XDB FL WLAN xx AP DAP 802 11 An FTB connection between the FL WLAN 510x and the device access point of a third party manufacturer can only work if the latter uses the same non standardized implementation This is possible but rather unlikely More detailed information regarding interoperability in FTB mode with other manufacturers cannot be provided 48 PHOENIX CONTACT 7191 en 03 Startup and configuration 3 7 3 Operating mode repeater The FL WLAN 510x offers repeater functionality This means that several devices in one line can be connected via WLAN One or more clients can log onto the individual devices in this repeater chain These can be connected via WLAN or the Ethernet copper ports See Figure 3 3 on page 49 and Figure 3 5 on page 51 This repeater function allows for the creation of a linear structure A meshed network or rings cannot be created Notebook a EECCCcc COHEN Client pn Zum aq MAIN qa Ww g Access Point Mode 1 i i i i i Repeater M
38. INET assistance mode 3 8 1 WLAN in PROFINET applications The use of WLAN in PROFINET applications means that certain individual parameters must be observed PROFINET places high demands on prompt data transmission also via the WLAN interface 3 8 1 1 Activating PROFINET assistance mode PROFINET assistance mode can be activated in the web menu under Service Configuration Alternatively PROFINET assistance mode can also be activated using the MODE button mode 3 FL WLAN 5100 5 E Service User Interfaces 0 Webserver mode Telnet Command Line Interface enable Secure Shell SSH enable 7 FL WLAN 5100 SNMP Sewer F Information Help amp Documentation Profinet assistance mode Device Status v nterface Side Disable configuration from WLAN Alarm amp Events Remote Syslog Server IP Address Connected Devices Configuration System Time Quick Setup Network Network time protocol dissbe H WLAN Advanced WLAN Primary SNTP Server 0000 Cluster Configuration Secondary SNTP Server pooo Service System Manual time set dicktosetime Local Events Network Events UTC offset 00h UTC GMT Lon Diagnostics Current system time 18h 37m 47s Channel Allocation Last SNTP synchronisation not synchronized by ContactGmbHSCo hG ard
39. IX CONTACT 7191_en_03 Technical data 6 Technical data General data Function Housing dimensions width x height x depth in mm External dimensions without antenna connections External dimensions with antenna connections Permissible operating temperature Permissible storage temperature Degree of protection Humidity Operation Storage Air pressure Operation Storage Mounting position Connection to protective earth ground Configuration Weight Supply voltage Connection Nominal value Permissible voltage range Current consumption at 24 V Power over Ethernet Protection class Interfaces RJ45 Ethernet interface Number Connection format Data transmission speed Segment length IP address assignment Wireless interface Antenna connection WLAN Ethernet access point client repeater 40 x 100 x 109 40 x 109 x 109 25 C to 60 C extended temperature range available on request the device when you operate the FL WLAN 510x in the extended temperature range from 40 C to 60 C The supply voltage should not fall below 12 V DC 1 At very low temperatures there may be a delay in the start up of 40 C to 80 C IP20 10 to 95 non condensing 10 to 95 non condensing 800 hPa to 1080 hPa up to 2000 m above sea level 660 hPa to 1080 hPa up to 3500 m above sea level Perpendicular to a DIN rail By means of the DIN rail Web based management via http or https SNMPv2 v3 CLI via Telnet
40. ROFINET applications it is recommended that the number of clients per access point is reduced to a few devices This can be achieved by using multiple access points and assigning different frequencies and SSIDs The configuration of an access point is described step by step in Section 3 4 1 on page 34 and Section 4 1 on page 70 3 7 2 Operating mode client 3 7 2 1 Compatibility between different WLAN device manufacturers The following describes points relating to the client configuration that should be noted when using WLAN devices from different manufacturers The Ethernet protocols and the number of Ethernet devices that can be used for transmission are described WLAN Client Mode Ethernet Y SCB All manufacturers One device e g PN on Li 2 ne e g PN only transmit transparently Layer 2 TCP IP transmits transparently on Layer 3 Pies SCB All manufacturers L3 Je L3 Ethernet MCB All manufacturers M Ethernet _ X Multiple devices e g TCP IP on Layer 3 a d only between devices from the same manufacturer all devices transmit transparently on Layer 2 3 Client N the technical implementation depends on the manufacturer FTB Ethernet Ethernet Multiple devices Layer 2 or Layer 3 Figure 3 14 Overview of the various client modes 46 PHOENIX CONTACT 7191_en_03 Startup and configuration 3 7 2 2 Operation as a single client Ethe
41. Start Inquiry Searches for devices that can be picked up in the cluster or are ready The devices must belong to the same subnetwork Table for cluster configuration Service User Interface Service Additional as yet unassigned devices can be assigned to the current cluster via the checkboxes You can assign the device you are currently logged into gray to another cluster via the radio button Webserver mode Selection of Webserver mode HTTPS security certificate HTTP standard unsecured Note Disable deactivates the web interface When confirmed with Apply amp Save the device can be accessed only via the CLI Telnet or SSH must be activated beforehand Telnet Command Line Interface Configuration of the device via Telnet Secure Shell SSH Configuration via Secure Shell SSH SNMP Server Selection of SNMP mode SNMPv2 SNMPv3 or SNMP deactivated Service Configuration PROFINET assistance mode IP address assignment via DCP supported If the device is operating in PROFINET assistance mode the PROFINET packets are classed as high priority based on their Ethertype value Strict prioritization is used Non PROFINET traffic is now limited to a maximum data throughput of 10 Mbps Allow configuration via WLAN If activated the device can be configured via its WLAN interface must be deactivated for PROFIsafe applications The configuration
42. W version 12 PHOENIX CONTACT 7191_en_03 Mounting 2 Mounting 2 1 Connections and operating elements NUUS SAT WLAN 57 0 Figure 2 1 Connections and operating elements of the device ooo ge o mw c COMBICON connections for supply voltage and one digital input or output X3 Two RJ45 Ethernet connections with 100 Mbps X1 X2 Mode button for setting various pre configured states Status and diagnostic LEDs Slot for optional SD memory card X4 RSMA antenna connections female X5 X6 X7 7191 en 03 PHOENIX CONTACT 13 FL WLAN 510x e 65 2 1 1 Electrical connection WLAN 5100 PHOENIX CONTACT Figure 2 2 Connecting the supply voltage and the input output 2 1 2 Mounting When using remote antennas always keep the antenna cable as short as possible to avoid an attenuation of the wireless signal Preferably use the mounting position illustrated in the following graphic 2 1 2 1 DIN rail mounting Use the DIN rail guide to position the module onto the upper edge of the DIN rail and snap the module into place by pushing it downward Figure 2 3 Snapping the module onto the DIN rail 14 PHOENIX CONTACT 7191 en 03 Mounting 2 1 2 2 Removal Insert a suitable tool e g flat bladed screwdriver into the latch and pull the latch downward B1
43. Wi Fi Protected Setup WPS a a 56 3 9 1 Running WPS using the MODE button 56 3 10 Quality Of Service con iore thc de e quie dele ertet eq tede teintes 56 3 41 Cluster management cerne ed cet dette ee ete eta doge ca dida 57 3 11 1 Searching and selecting cluster devices 57 3 11 2 Identifying cluster relevant parameters in the web interface 62 3 11 3 Properties of cluster management sssem 63 3 12 Using tile transfer scr holies eee Gs ie leone 63 3 13 DHCP Server Eee redd n d dade 64 3414 Event handlinga ossiani inek ree tbe a i EH rest 65 3 14 1 Selecting events in web based management 66 2 MIB TOOL Or IS sua tetas cats So etate etes 69 4 1 Parameter list for the 70 B JBiBgridslies cas aca dood atu us eite a Leute 83 5 1 WLAN signal strength diagnostics on the 83 5 2 Diagnostics of WLAN channel assignment on the access point 85 6 Technical ata ERO verias ened 87 6 1 Ordering data x ine IR dien dy Si Sere Beha n cu d
44. X CONTACT 7191 en 03 Menu functions Table 4 1 Parameter list for Information page Designation Description Grant access to IP Channel allocation The IP address of the device in the network which should be accessible via Machine Admin mode second SSID is entered here Note It must be in the same address area as the WLAN 510x see Network configuration Graphic In access point mode the Channel Allocation web page displays a graphical overview of the channels occupied by WLAN systems The data displayed is cleared when the web page is exited RSSI graph Graphic In client mode the RSSI Graph web page has a graphical RSSI logger which displays the time curve for the RSSI values on the client The data displayed is cleared when the web page is exited 7191_en_03 PHOENIX CONTACT 81 FL WLAN 510x 82 PHOENIX CONTACT 7191_en_03 Diagnostics 5 Diagnostics 5 1 WLAN signal strength diagnostics on the client If the FL WLAN 510x is in client or repeater mode the current WLAN signal strength of the connected access point or repeater can be displayed This function can be used to determine the signal strength when setting up wireless paths Thanks to the dynamic display it is possible to determine the signal strength of an access point at various locations e g mobile clients or to determine the optimum alignment of an antenna in the ca
45. a RR E ch 89 6 PHOENIX CONTACT 7179 en 04 WLAN 5100 next generation industrial WLAN Industrial WLAN network solutions from Phoenix Contact open up new possibilities for creating production and logistics processes more efficiently reliably and simply The fields of application are e Reliable safe and fast communication with mobile or moving automation and production systems e Realtime access to network resources and service information for increasing productivity and accelerating decision processes The WLAN modules in the 510x series offer maximum reliability data throughput and range The new WLAN 510x combines rugged industrial technology with high 802 11n performance and modern MiMo multiple input multiple output antenna technology in extremely compact metal housing MiMo technology with three antennas significantly increases the ruggedness speed and range of your wireless communication This is particularly noticeable under challenging industrial conditions A special feature of the WLAN 510x modules is their quick and easy configuration The configuration of a WLAN access point is automatically distributed to all other access points in the WLAN network using the cluster management function At the touch of a button WLAN clients can also be integrated easily into the WLAN network without configuration thanks to WPS Wi Fi Protected Setup 7191 en 03 PHOENIX CONTACT 7 FL WLAN 510x 1 Technical description
46. a gain permitted for devices in the band 5725 5825 MHz shall comply with the e i r p limits specified for point to point and non point to point operation as appropriate Users should also be advised that high powers radars are allocated as primary users i e priority users of the bands 5250 5350 MHz and 5650 5850 MHz and that these radars could cause interference and or damage to LE LAN devices IMPORTANT NOTE IC Radiation Exposure Statement This equipment complies with IC RSS 102 radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between radiator amp your body This module is intended for OEM integrator The OEM integrator is still responsible for the IC compliance requirement of the product which integrates this module 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into Under such configuration the IC RSS 102 radiation exposure limits set forth for a population uncontrolled environment can be satisfied Any changes or modifications not expressly approved by the manufacturer could void the users authority to operate this equipment 7191 en 03 PHOENIX CONTACT 11 FL WLAN 510x 1 3 Firmware Table 1 1 Firmware version Functionality FW 1 60 The machine admin mode second SSID and DHCP server func tions are available as of this F
47. adio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna ncrease the separation between the equipment and receiver Connectthe equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help To comply with FCC part 15 rules in the United States the system must be professionally installed to ensure compliance with the Part 15 certification It is the responsibility of the operator and professional installer to ensure that only certified systems are deployed in the United States The use of the system in any other combination such as co located antennas transmitting the same information is expressly for bidden FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For product available in the USA Canada market only channel 1 11 2 4GHz can be operated Selection of other channels is
48. ap Internal Syslog Send to Set digital Error LED entry external Syslog output lights up server Device start Yes Always Yes configurable configurable Link up link down Yes Always Yes configurable configurable IPAssign tool download Always Yes configurable User login failed Yes Always Yes configurable configurable Power supply low level Yes Always Yes configurable configurable Error LED ON OFF Yes Yes Yes configurable configurable Client connected not Yes Always Always connected configurable Roaming performed Yes Always Yes configurable configurable Client mode changed Yes Always Yes Yes Yes configurable configurable configurable configurable 7191_en_03 PHOENIX CONTACT 65 FL WLAN 510x 3 14 1 Selecting events in web based management Various events can be selected on the System Events web page the occurrence of which generates an external Syslog entry or sends an SNMP trap In addition the SNMP trap receivers are defined here LS n PHENIX FL WLAN 5100 YB SNMP Trap 10 10 2 23 FL WLAN 5100 Add new IP address add Information Help amp Documentation Device Status Interface Status Alarm amp Events Connected Devices Configuration Quick Setup Network WLAN Advanced WLAN Cluster Configuration Service System Local Events Network Events Diagnostics Channel Allocation Copa by Phoeak
49. ations which are to take effect after a device restart must be saved permanently SNMP interface All managed Factoryline components have an SNMP agent This device agent manages Management Information Base II MIB 2 according to RFC1213 and private SNMP objects from the Phoenix Contact MIB PXC WLAN MIB Network management stations such as a PC with Factory Manager can read and modify configuration and diagnostic data from network devices via the Simple Network Management Protocol In addition any SNMP tools or network management tools can be used to access Factoryline products via SNMP To do this the MIBs supported by the relevant device must be made available to the SNMP management tools On the one hand these are globally valid MIBs which are specified and described in RFCs Request for Comments This includes for example MIB2 according to RFC1213 which is supported by all SNMP compatible network devices On the other hand manufacturers can specify their own SNMP objects which are then assigned to a private manufacturer area in the large SNMP object tree Manufacturers are then responsible for their own private enterprise areas i e they must ensure that only one object is assigned to an object ID object name and parameters and can be published If an object is no longer needed it can be labeled as expired but it cannot be reused with other parameters under any circumstances Phoenix Contact provides notifi
50. cation of ASN1 SNMP objects by publishing their descriptions on the Internet Reading SNMP objects is not password protected However a password is required for read access in SNMP but this is set to public which is usual for network devices and cannot be modified By default upon delivery the password for write access is private and can be changed by the user For SNMP the password public is used for read only access the password private for read write access 7191_en_03 PHOENIX CONTACT 93 FL WLAN 510x Another benefit for the user is the option of sending traps using the Simple Network Management Protocol Management Information Base MIB Database which contains all the data objects and variables required for network management Agent An agent is a software tool which collects data from the network device on which it is installed and transmits this data on request Agents reside in all managed network components and transmit the values of specific settings and parameters to the management station On a request of a manager or on the occurrence of a specific event the agent transmits the collected information to the management station Schematic view of SNMP management Management station SNMP management Trap receiver E SNMP traps Management objects organized in MIBs
51. ce under Device status Device contact Enter the desired contact address here that will be displayed in the web interface under Device status Firmware update Select the type of firmware update TFTP or HTTP Firmware update pop up window Upload protocol Choose whether the firmware update should be carried out via TFTP or HTTP Remote firmware filename In the case of TFTP the file name and path of the TFTP server must be specified here Current active image Display of the current active firmware version Two firmware images can be stored on the WLAN device The image displayed here is the active one After a firmware update or when another firmware image is selected the device must be restarted If the Automatic reboot after upload checkbox is activated this will be carried out automatically on completion of the update Next active image Another firmware image can be activated here By default there is only one firmware image on the device SD card state Shows whether an SD card is inserted in slot X4 The web page must be reloaded in order to display the current status Note only specially formatted SD cards from Phoenix Contact can be used Perform action Load configuration loads the device configuration stored on the SD card and executes it Save configuration Save device independent configuration saves the device independent parameters to the wlan_510
52. cluster detect that the cluster configuration was changed as soon as they go online again and apply the new configuration automatically When a cluster relevant change to the configuration of a device is saved this triggers saving on all cluster members 3 12 Using file transfer Various files can be transferred between the configuration PC and the device using HTTP s or TFTP Table 3 1 File transfer File Upload Download Device documentation Yes SNMP MIB files Yes Security context Yes Yes CA root certificate Yes Yes Client certificates Yes Yes Event log files Yes Firmware files Yes Device configuration Yes Yes 7191_en_03 PHOENIX CONTACT 63 FL WLAN 510x 3 13 DHCP server The FL WLAN 510x has a DHCP server IP addresses can be assigned via WLAN or the Ethernet interface copper By default upon delivery the DHCP server is deactivated The DHCP Server item can be found in the Network menu under Configuration Configuration is performed here DHCP server To activate the DHCP server IP address assignment must be set to static under Network configuration After selecting enable the following parameters can be configured FL WLAN 5100 Connected clients ral DERA Le B Network configuration IP address assignment IP address 192 168 0 250 Subnet mask 255 255 255 0 FL WLAN 5100 Gat
53. ddress the device stops sending BootP requests After receiving a BootP reply the device no longer sends BootP requests Following a restart a device that was previously configured sends three BootP requests if these requests are not answered the device starts with the IP address that was last assigned via BootP After the default settings are restored the device sends BootP requests until they are answered DHCP dynamic request for an IP address from a DHCP Dynamic Host Configuration Protocol server IP address Entry of the static IP address in format 192 168 0 254 Subnet mask Entry of the static subnet mask in format 255 255 255 0 Gateway Assignment of the gateway in format 0 0 0 0 Nameserver If aname server is used the destination address is entered here in format 0 0 0 0 DHCP Server DHCP Server The DHCP server assigns IP parameters to network devices This is performed via both methods the cable based Ethernet interface and WLAN To activate the function IP address assignment must be set to static first IP pool starting address The first IP address to be assigned by the DHCP server is entered here Size of pool The number of DHCP clients which may receive an address is entered here The number can be between 1 and 1000 Subnet mask The DHCP server uses the local subnet mask It is configured under Network configuration Gateway Assignment of
54. der firmware version on the card will be installed if the SD card is inserted and the newer device firmware will therefore be overwritten This function ensures 1 1 function compatibility in the event of device replacement In the case of a newer device the dual image concept can be used if necessary to switch easily to the second newer image in the AP Note loading the device configuration The device configuration is loaded from the SD card to the WLAN device The WLAN configuration must be saved to the SD card in a folder with the name FLConfig so that the WLAN 510x can access it G H FLConfigiwlan_dev_1101 loj x Datei Bearbeiten Ansicht Favoriten Extras ay 2 gt T JO suchen Ordner gt F x I Ez Adresse e H FLConfig wlan_dev_1101 Wechseln zu Name Gfe Typ Ge ndert am a wlancert Dateiordner 22 11 2011 17 29 8 configuration 1KB Datei 22 11 2011 17 29 E SecurityContext ctx 3KB 22 11 2011 17 29 8 wlan dev pxc 23 584KB PXC Datei 22 11 2011 17 30 Figure 3 13 Folder for saving the configuration file on the SD card All configuration data is saved with the exception of some parameters that should not be overwritten when the configuration data is later transferred to other devices via the SD card 42 PHOENIX CONTACT 7191 en 03 Startup and configuration 3 6 Firmware update A firmware update can be p
55. e gt RSMA male insertion loss RAD PIG EF316 N RSMA 2701402 0 75 dB at 2 4 GHz 1 25 dB at 5 GHz impedance 50 ohms Antenna cable 0 5 m in length N male gt RSMA male impedance RAD PIG RSMA N 0 5 2903263 50 ohms Antenna cable 1 m in length N male gt RSMA male impedance RAD PIG RSMA N 1 0 2903264 50 ohms Antenna cable 2 m in length N male gt RSMA male impedance RAD PIG RSMA N 2 0 2903265 50 ohms Antenna cable 3 m in length N male gt RSMA male impedance RAD PIG RSMA N 3 0 2903266 50 ohms Antenna cable 3 m in length N male gt N male attenuation approx RAD CAB EF393 3M 2867649 0 45 dB at 2 4 GHz impedance 50 ohms Antenna cable 5 m in length N male gt N male attenuation approx RAD CAB EF393 5M 2867652 0 45 dB at 2 4 GHz impedance 50 ohms Antenna cable 10 m in length N male gt N male attenuation approx RAD CAB EF393 10M 2867665 0 45 dB at 2 4 GHz impedance 50 ohms Antenna cable 15 m in length N male gt N male attenuation approx RAD CAB EF393 15M 2867634 0 45 dB at 2 4 GHz impedance 50 ohms 90 PHOENIX CONTACT 7191 en 03 Technical data Description Order designation Order No Adapter RSMA male gt SMA female insertion attenuation lt 0 3 dBat RAD ADP RSMA F SMA F 2884538 2 4 GHz Attachment plug with LAMBDA 4 technology as surge protection for CN LAMBDA 4
56. e 5 2 The checkbox can only be activated if a connection already exists The current signal strength in dBm is displayed to the right of the bar graph The average signal strength as well as maximum and minimum values during the current measuring period are displayed below Measurement is stopped when you exit the web page FL WLAN 5100 SEJ T x IP Address 192 168 0 251 Network Mask 255 255 255 0 Default Gateway 0 0 0 0 Nameserver Address 0 0 0 0 IP Assignment static FL WLAN 5100 MAC Address 00 0 45 36 06 LAN Status Port 1 100baseT full duplex LAN Status Port 2 no link Information Help amp Documentation Device Status Interface Status Alarm amp Events Configuration Quick Setup Network WLAN Advanced WLAN Cluster Configuration Service System Local Events Network Events Diagnostics RSSI Graph Copyright by CotctGmbHa Co KG aid Otter Radio Status Operating Mode Connect State Network SSID Datarate Signal Strength RSSl Long Distance mode Current TX power Channel Security Mode Interface Status WLAN enabled Client FTB Fully Transparent Bridge Accesspoint 00 A0 45 36 E9 B6 PxC Messung 130 MBit 27 dBm Show signal bar normal 17 dBm Sai WPA2 PSK Current Signal Strength RSSl ae Signal Strength min avg max 5 dBm 30dBm 25dBm 45dBm
57. e admin configuration under Configuration Country regulatory domain When a country is selected regulatory conditions such as special wireless channels are taken into consideration Network SSID The SSID is the network ID via which clients are assigned to the access points It can be a maximum of 32 characters long Letters numbers and the following characters are permitted amp _ lt gt Hide SSID Hide the SSID If Hide SSID is used when the access point is operating 5 GHz DFS channel please note that because the clients may not actively scan this area and due to passive scans and the missing SSID in the beacons of the access point it may not be possible to find the correct access point WLAN band Selection of the frequency band Other operating modes according to IEEE 802 11 are available in the Advanced WLAN menu 74 PHOENIX CONTACT 7191_en_03 Menu functions Table 4 1 Parameter list for Information page Designation Description Channel Channel selection possible channel selection depends on the setting made under WLAN band Indoor Ch36 Ch48 4 channels can be freely selected Indoor 8 channels automatically indoor 16 channels automatically the system selects the channels automatically DFS The connection may be interrupted during a channel switchover Automatic The device automatically selects a WLAN c
58. e entered automatically even during later operation To avoid this it is recommended that you use manual SCB mode 3 7 2 2 2 Manual SCB If several Ethernet devices are connected to the Ethernet port of the FL WLAN 510x on the cable side it is recommended that the MAC address of the device that is to be connected via the WLAN interface is entered manually in the web interface In contrast to automatic mode this will ensure that this specific device is addressed The other devices in the network cannot be accessed via WLAN In Single Client Bridge SCB mode the data is transmitted transparently on Layer 2 Only the device whose MAC address is entered for FL WLAN 510x can be accessed via WLAN 7191_en_03 PHOENIX CONTACT 47 FL WLAN 510x 3 7 2 3 Operation as a multi client Properties Connects several Ethernet devices connected via Ethernet switches to the access point on Layer 3 Ethernet device is detected automatically Operates between all WLAN devices even devices access points from third party manufacturers Several network devices can therefore be connected on the cable side In this mode restrictions apply and not all protocols are transmitted just Layer 3 transparent protocols This includes for example TCP IP but not PROFINET or EtherNet IP 3 7 2 4 Operation as a fully transparent bridge default Properties Connects several Ethernet devices connected via
59. ed BOOTP requests from MAC Address Count Last Request Time 00 0 45 04 08 3 2 14 33 06 If you do not see the Mac address of the device you are looking for try cycling power to that device Show Only Phoenix Contact Devices Abbrechen Figure 3 2 IP Address Request Listener window In this example the device has MAC ID 00 A0 45 04 08 A3 e Select the device to which you would like to assign an IP address e Click on Next Step 4 Set IP Address The following information is displayed in the window which opens P address of the PC MAC address of the selected device parameters of the selected device IP address subnet mask and gateway address incorrect settings 26 PHOENIX CONTACT 7191 en 03 Startup and configuration Phoenix Contact IP Assignment Tool Set IP Address Please specify an IP Address to use This PC s IP Address 192 168 1 100 Please specify the IP Address to be used below Selected MAC Address 00 20 45 04 08 3 TP Address Subnet Mask Gateway Address WARNING this address is in a different Subnet Once you have entered a valid IP address click Next lt Zur ck Abbrechen Figure 3 3 Set IP Address window with incorrect settings e Adjust the IP parameters according to your requirements If inconsistencies are no longer detected a message appears indicating that a valid IP address has been set e Click
60. ed of roaming varies depending on the type of client used Roaming is rather slow in the case of a notebook For applications where roaming needs to be carried out in a fraction of a second industrial WLAN clients must definitely be used Roaming is primarily defined via the client Access points are effective due to their physical location set transmission power and antenna They make sure that there is sufficient network coverage available at every location The FL WLAN 510x is already optimized for fast roaming in client mode The user can only improve effectiveness by restricting channels via the Roaming search list under Advanced WLAN configuration see Section 4 1 on page 70 Network planning The frequencies to be specified for the wireless channels are also defined via the access point ideally as early as the WLAN network planning stage In addition it may be possible to select the transmission standard according to 802 11 Multiple WLAN clients can be connected simultaneously to every access point Due to the higher number of clients per access point the amount of data that can be transmitted via each individual client is reduced This can vary to a greater or lesser extent depending on how much data the application requests via the individual clients If the application has time requirements the number of clients must also be taken into consideration For example for 7191_en_03 PHOENIX CONTACT 45 FL WLAN 510x P
61. ee Figure 3 10 on page 59 Up to 20 access points can be grouped into a cluster An Ethernet network can have several clusters 58 PHOENIX CONTACT 7191 en 03 Startup and configuration 3 http ft 92 168 0 101 php clustergroup_config php reload 1 Cluster Group Configuration 0000000000000 Cluster Name Start Inquiry Inquiry Process Device Name IP Address B not assigned FL WLAN 5101 192 168 0 100 FL WLAN 5100 192 168 0 102 FL WLAN 5100 192 168 0 104 B test_cluster test_cluster MAC Address 00 0 45 02 00 0 45 36 9 00 15 61 10 58 E2 Device Type Cluster Member FL WLAN 5101 FL WLAN 5100 FL WLAN 5100 FL WLAN 5100 192 168 0 101 00 A0 45 37 1F CC FL WLAN 5100 Figure 3 10 List and configuration options for the cluster created Once all desired access points have been selected by activating the corresponding checkbox click on Apply to start creating and configuring the cluster The configuration of the preset access point is transferred to all the other devices The process can take a little time depending on the number of access points in the cluster 7191_en_03 PHOENIX CONTACT 59 FL WLAN 510x B http 192 168 0 101 php clustergroup_config php reload 1 lY configure Cluster Group Figure 3 11 Automatic configuration of the selected cluster Atable containing all the access points belonging t
62. er with the signal word NOTE and the accompanying text alert the reader to a situation which may cause damage or malfunction to the device hardware software or surrounding property formation or refer to detailed sources of information i This symbol and the accompanying text provide the reader with additional in How to contact us Up to date information on Phoenix Contact products and our Terms and Conditions can be found on the Internet at www phoenixcontact com Make sure you always use the latest documentation It can be downloaded at www phoenixcontact n tal If there are any problems that cannot be solved using the documentation please contact your Phoenix Contact subsidiary Subsidiary contact information is available at www phoenixcontact com PHOENIX CONTACT GmbH amp Co KG FlachsmarktstraBe 8 32825 Blomberg GERMANY Should you have any suggestions or recommendations for improvement of the contents and layout of our manuals please send your comments to tecdoc phoenixcontact com PHOENIX CONTACT Please observe the following notes General terms and conditions of use for technical documentation Phoenix Contact reserves the right to alter correct and or improve the technical documen tation and the products described in the technical documentation at its own discretion and without giving prior notice insofar as this is reasonable for the user The same applies to any technical changes that serve
63. erformed directly via the web interface e Todo so select Update Firmware under the System menu item A Firmware Update pop up window allows you to choose whether to update the firmware via HTTP or TFTP Note Please keep in mind that the configuration settings of the device may be lost when you downgrade the firmware 3 6 1 HTTP Select HTTP and click on the Upload a file button Then select the folder containing the new firmware The new firmware file is a pxc file The firmware is loaded and the update status is indicated by a progress bar Update finished is displayed as the status when the update is completed e Close the Firmware Update window To activate the new firmware the device must be restarted This can be activated by clicking on the Auto Reboot or Reset button at the top of the System web window or by performing a voltage reset for the device 3 6 2 TFTP Select TFTP and enter the IP address of the TFTP server in the window provided for this purpose In the Remote firmware filename window enter the path and name ofthe firmware file see also Using file transfer on page 63 e Start the TFT file transfer by clicking on the upload button e Close the Firmware Update window e To activate the new firmware the device must be restarted This can be activated by clicking on the Reset button at the top of the System web window or by performi
64. es data throughput Multiple devices can be connected to all FL WLAN 510x devices in repeater mode via the Ethernet port or the WLAN wireless interface In repeater mode the data is transmitted sequentially via a single wireless channel This means that the overall data rate that can be achieved decreases as the number of devices and repeaters increases The data throughput that can be achieved is dependent on these factors on the potential use of the wireless channel by other devices as well as on the distance between the individual devices As a result no general statement can be made as to the possible data throughput amount With respect to the clients connected via WLAN repeater mode supports FTC SCB and MCB see Section Operation as a client on page 36 and Section Wi Fi Protected Setup WPS on page 56 qp d 4 Notebook a WLAN EPA Client Client Client 7 Mode PLC i Access Point Repeater Mode Mode LU 5 Ethernet Ethernet 5 Figure 3 5 FL WLAN 510x in repeater mode device connection via RJ45 or WLAN All FL WLAN 510x devices in a network that are configured as repeaters operate with one SSID one security mode and one passkey The same applies to the clients that are connected to the repeaters via WLAN All devices use a single wireless channel The use of WPS is not supported in repeater mode 5 7191_en_03 PHOENIX CONTACT 51 FL WLAN 510x
65. eway 0 0 0 0 Nameserver ln 0 0 0 Information Help amp documentation Device status DUCE Server Interface status DHCP Sewer enabe gt Alarm amp events Connected devices Configuration IP pool starting address 192 168 0 20 Quick setup Size of pool 10 Network WLAN Subnet mask 255 255 255 0 Advanced WLAN Senice Gateway 0 0 0 0 System Lease time 3600 Local events Network events 0 admin configuration Revert Apply Apply amp Save iagnostics Channel allocation Copia by Picea cortsctGmbHSCo MG ad ofer Figure 3 14 use the DHCP server IP address assignment must be set to static IP pool starting address The first IP address to be assigned by the DHCP server is entered here Size of pool The number of DHCP clients which may receive an address is entered here The number can be between 1 and 1000 Subnet mask The settings of the local subnet mask from the Subnet mask field under Network configuration are automatically entered in this field The subnet mask is assigned by the DHCP server Gateway Assignment of the gateway in format 0 0 0 0 Lease time Time interval in seconds during which the IP address is valid 64 PHOENIX CONTACT 7191 en 03 Startup and configuration 3 14 Event handling Various events trigger various reactions on the device Table 3 2 Event handling Event SNMP tr
66. figuration Service System Local Events Network Events Diagnostics Channel Allocation by Piori CortctGmbHe Co KG and Otter Country Regulatory Domain Germany Operating Mode Client FTB Indoor Network SSID Pxc Scan WLAN Security WPA2PSK AES v Passkey eseeeece Show cleartext passphrase Administrator Password Retype Password Revert Apply Apply amp Save Figure 3 9 Quick Setup web page after selecting client mode Network SSID The network SSID is used to identify the network to which the WLAN clients connect wirelessly The name entered here allows the WLAN client to search for an access point with the same SSID When using the correct encryption a connection can be established with the access point In order to reach full data throughput under WLAN 802 11n WPA2 PSK AES encryption must be used The network name can be up to 32 characters long Letters numbers and the following characters are permitted amp _ lt gt If the SSID of the access point with which the wireless connection is to be established is known it can be entered in the Network SSID field Scan button An alternative to typing in the SSID is to click on the Scan button and search for WLAN access points that can be reached Please note that any existing connections will be interrupted during scanning All frequencie
67. hannel Note if the device is operated outdoors in the 5 GHz band outdoor mode must be activated This information is valid for Europe Output power Selection of the transmission power at the antenna connection Maximum corresponds to the maximum transmission power that can be output by the wireless module or which is permitted by regulations Note antenna gain and cable attenuation must be taken into consideration by the user WLAN Security Security Mode None operation without encryption puts network security at risk WPA PSK TKIP used by older devices that do not support WPA AES WPA2 PSK AES secure and faster for client roaming WPA2 EAP enables the use of authentication servers AAA server RADIUS server In order to reach full data throughput under WLAN 802 11n WPA2 PSK AES encryption must be used Passkey Key during the initialization of WPA encryption Note for maximum security a random alphanumeric string up to 63 characters should be used Letters numbers and the following characters are permitted amp _ lt gt 7191 en 03 PHOENIX CONTACT 75 FL WLAN 510x Table 4 1 Parameter list for Information page Designation Advanced WLAN Advanced WLAN configuration on the access point Description WLAN band Selection of the frequency band Channel Bandwidth 802 11n 20 MHz operation of the device on one wirele
68. hen the device is booted this configuration including the firmware version is applied and the previous configuration is overwritten in the internal memory NOTE If an SD card without firmware image is detected during a boot process ora firmware update was carried out prior to booting the boot process will take longer as the firmware has to be copied from the device to the SD card first Do not remove the SD card until the last boot LED has gone out O Figure 3 12 Inserting the SD card The configuration data for the FL WLAN 510x can be saved to the SD card and downloaded from the SD card to the WLAN device The Perform action menu for this purpose is located under System in the web interface 1 The device also be operated without an SD card The configuration is also stored in the internal memory of the device 7191_en_03 PHOENIX CONTACT 41 FL WLAN 510x 3 5 2 Saving the device configuration The active device configuration is saved to the SD card This configuration can then also be transferred to another device In addition to the configuration the current firmware image is also stored on the SD card This too is read from the card after power up if it differs from the internal firmware image present on the device 1 NOTE Device downgrade If there is an older version of the device firmware on the SD card on a power up the ol
69. interfaces WBM SNMP CLI via Telnet SSH are still available via Ethernet 7191_en_03 PHOENIX CONTACT 77 FL WLAN 510x Table 4 1 Parameter list for Information page Designation Description Remote Syslog Server IP Address Diagnostic messages are redirected to the device with the specified IP address The IP address 0 0 0 0 deactivates the forwarding of messages to the Syslog server System Time Network time protocol If the time synchronization of an existing time server is to be used it must be activated here Primary SNMP Server Entry of the IP address of the primary SNTP server Secondary SNMP Server Entry of the IP address of the secondary SNTP server Manual time set The system time is set here if an SNTP server is not available UTC offset Selection of the time zone For the times in the event table for example make sure that the system time corresponds to Greenwich Mean Time The current local time is based on the system time and the UTC Offset Where necessary the switch between daylight savings and standard time must be taken into consideration Current system time Display of the current system time Last SNTP synchronization System If an SNTP server is available in the network the time is automatically applied from this server if Network time protocol is activated The time of the last synchronization is displayed here
70. ion X3 Reaction on digital input high event Definition of the action that is triggered when the digital input is set to High Local events digital output Status The digital output can be set here for test purposes via the web interface To do this Access must be activated Access Activation of access via SNMP CLI or the web interface If this is not desired access should be deactivated here Network Events Network events Access is then only possible via the event table SNMP trap In this area you can select which system events should be recorded and on which interface they should be output They can be output in the Syslog server or as an SNMP trap Add new IP address Machine admin configurati Machine admin configurati Add a new trap receiver to the list Second SSID This second SSID network ID in addition to the SSID of the access point is used to assign a service access to the access point The SSID can be a maximum of 32 characters long Letters numbers and the following characters are permitted amp _ lt gt Passkey For encryption of the machine admin network Note for maximum security a random alphanumeric string up to 63 characters should be used Letters numbers and the following characters are permitted amp _ lt gt The password must be at least eight characters long 80 PHOENI
71. itable for installation in zone 22 If however you wish to use the device in zone 22 it must be installed in a housing that complies with EN 60079 0 In doing so observe the maximum surface temperatures Adhere to the requirements of EN 60079 14 Installation in zone 2 Observe the specified conditions for use in potentially explosive areas When installing the device use an appropriate and approved housing with a minimum protection of IP54 Atthe same time observe EN 60079 14 requirements Only devices which are designed for operation in zone 2 and are suitable for the conditions at the installation location may be connected to the supply and signal circuits in zone 2 In potentially explosive areas only connect and disconnect cables when the power is disconnected You must only work on the device if it has been ensured that there is no explosive environment The device must be stopped and immediately removed from the Ex area if it is damaged was subjected to an impermissible load stored incorrectly or if it malfunctions In addition for FL WLAN 5100 Ensure that the radiated wireless power is neither bundled focused by the antenna itself nor by any inserts in the environment of the antenna and that it cannot enter neighboring zones 1 or 0 Please refer to the technical data for the transmission power Application note The HF antenna cable must be suitable for the ambient conditions and should be installed in a way that
72. loaded via a link Connected Devices Only in access point mode the connected devices client mode and their parameters are displayed in table format 70 PHOENIX CONTACT 7191_en_03 Menu functions Table 4 1 Parameter list for Information page Designation Description Configuration interface Quick Setup any configuration on this page always activates the WLAN Web management language Select the language for the web interface Enable cookies in your browser Otherwise the language will be reset to English when you log in again IP Address Assignment Static a static IP address is assigned to this interface BootP during initial startup the device transmits BootP requests without interruption until it receives a valid IP address As soon as it receives a valid IP address the device stops sending BootP requests After receiving a BootP reply the device no longer sends BootP requests Following a restart a device that was previously configured sends three BootP requests if these requests are not answered the device starts with the IP address that was last assigned via BootP After the default settings are restored the device sends BootP requests until they are answered DHCP dynamic request for an IP address from a DHCP Dynamic Host Configuration Protocol server Country Regulatory Domain Select the country in which the device is operated from the list
73. mately 200 mm to 500 mm between the antennas are mechanically feasible this may lead to further improvement For the same reason antennas should not be screwed directly onto the device Figure 2 10 Do not screw several antennas onto the device 18 PHOENIX CONTACT 7191 en 03 Startup and configuration 3 Startup and configuration Installation notes The category 3 device is designed for installation in the potentially explosive area of zone 2 It meets the requirements of EN 60079 0 2009 and EN 60079 15 2010 Installation operation and servicing may only be carried out by qualified electricians Follow the installation instructions as described When installing and operating the device the applicable regulations and safety directives including national safety directives as well as general technical regulations must be observed The safety data is provided in this user manual and on the certificates conformity assessment additional approvals where applicable Do not open or modify the device Do not repair the device yourself but replace it with an equivalent device Repairs may only be performed by the manufacturer The manufacturer is not liable for harm resulting from noncompliance The IP20 degree of protection IEC 60529 EN 60529 of the device is intended for use in a clean and dry environment Do not subject the device to mechanical and or thermal loads that exceed the specified limits The device is not su
74. modes Client mode is subdivided into three options FTB Fully Transparent Bridge SCB Single Client Bridge and MCB Multi Client Bridge Each operating mode supports different applications 3 7 1 Operating mode access point In Access Point mode the FL WLAN 510x represents the wireless interface of an Ethernet network WLAN devices can be connected wirelessly to a network via this access point Important parameters The WLAN network which is represented by one or more access points is assigned a network name known as the SSID Service Set Identifier which is its main feature In order to ensure that network security is protected against unauthorized access via the WLAN interface according to IEEE 802 11i secure encryption must also be used see Section 3 4 1 on page 34 The network name and encryption are defined in the access point They can be entered via the web interface Any WLAN client that would like to access the network via this access point must know the SSID and encryption If WLAN access is to take place at several points in an Ethernet network or a wide area is to be covered multiple WLAN access points are used which are connected to the network If all of these access points use the same SSID and encryption a connected WLAN client can switch between the access points Roaming The process where a WLAN client switches from one access point to another is known as roaming The spe
75. ms of the frequency usage of the device are automatically taken into consideration The settings primarily affect the device when it is used in the 5 GHz WLAN band A wireless license is not necessarily available for each country that can be selected here 32 PHOENIX CONTACT 7191_en_03 Startup and configuration Operating mode Under Operating Mode you can define whether the device assumes the function of an access point or a client in the network f 7 7 SY iz FL WLAN 5100 AX 3 4 6 Q i 4 5 Web management language English yj IP Address Assignment static FL WLAN 5100 IP Address 192 168 0 254 x Subnet Address 7 255 255 255 0 Information Gateway Address 0000 Help amp Documentation Device Status Interface Status A Country Regulatory Domain v A EI y Reg y Y Germany Connected Devices Operating Mode Accesspoint Configuration Quick Setup Network WLAN Advanced WLAN Cluster Configuration Service System Local Events Network Events Diagnostics Channel Allocation Copyright by Phonk ContactGmbHSCo KG and Otter 24 Network SSID PxC WLAN Band Channel WLAN Security Passkey 2 4GHz 802 11 b g n v Channel 2 442GHz WPAZ PSK AES Show cleartex
76. n 7191 en 03 PHOENIX CONTACT 29 FL WLAN 510x Web interface buttons Meaning of the individual buttons Table 3 6 Meaning of the buttons Icon Meaning This button deletes the entries made since the last saved entry This button applies the current settings but does not save them This button applies and saves the current settings 30 PHOENIX CONTACT 7191 en 03 Startup and configuration 3 4 Quick setup The Quick Setup feature on the web page allows you to quickly configure the minimum requirements of a WLAN network The procedure is described below Establishing a connection to the device e Connect the device to the supply voltage and connectit to the PC via an Ethernet cable e Setthe device to mode 6 using the MODE button see Configuration using the MODE button on page 21 As a DHCP server the device assigns an IP address to the PC connected via the Ethernet network Make sure that your PC is ready for IP assignment using DHCP e Using a browser to IP address 192 168 0 254 In web based management select Quick Setup e Login enter admin as the username and private as the password QE EPHOENIX FL WLAN 5100 R CONTACT Login Username admin Password FL WLAN 5100 Information Help amp Documentation Device Status Interface Status Alarm amp Events Connected Devices
77. n method or to easily add devices 3 9 1 Running WPS using the MODE button Please note that the WPS function is disabled automatically after 120 seconds for security reasons Make sure you only ever set one access point to WPS mode This will prevent clients connecting to an incorrect access point Please note that the WPS function cannot be used if certificates are used Sequence e Activate the WPS Access Point function for the access point on the Advanced WLAN web page The access point can now be accessed by clients for 120 seconds during this time the link quality LEDs flash yellow Once this time has elapsed the device returns to configuration mode Select WPS Client mode for the client using the MODE button The client can now be accessed by access points for 120 seconds during this time the link quality LEDs flash yellow Once this time has elapsed the device returns to configuration mode If the device has received valid configuration parameters the link quality LEDs flash green if no configuration was received the link quality LEDs flash yellow and the error LED lights up red 3 40 Quality of service The device supports Quality of Service QoS in the following way use of QoS is supported both according to IEEE 802 1p and according to IEEE 802 116 The device evaluates IP ToS and VLAN tags Ifthe device is operating in PROFINET assistance mode the PROFINET
78. ndard in encryption WPA PSK TKIP is available as an alternative Other encryption options are available in the WLAN menu We strongly recommend using secure encryption in order to protect your network against unauthorized access In order to reach full data throughput under WLAN 802 11n WPA2 PSK AES encryption must be used 38 PHOENIX CONTACT 7191 en 03 Startup and configuration Passkey Enter a key which will be used by the device during the initialization of WPA encryption Note for maximum security arandom alphanumeric string up to 63 characters should be used Letters numbers and the following characters are permitted amp _ lt gt After clicking on Apply the client automatically establishes a connection to the access point If this does not happen check that the entries for the SSID network security and passkey match those of the access point If the security of the installation permits it a test run without using encryption can simplify startup However during operation secure encryption should be activated Administrator Password The password for accessing the web interface is changed under Administrator Password and confirmed under Retype Password The change is only applied when you click on Apply To permanently save the change beyond a device restart click on Apply amp Save We strongly recommend that you change the administrator password the fi
79. nenneen nennen 28 3 8 1 General information in the web interface 29 3 4 Quick setup se tates M e tester 31 3 4 1 Operation as an access point sssssssseeeeeene 34 3 4 2 Operation as a client 36 3 5 SD card for saving the device configuration seen 40 3 5 1 Inserting the SD Card toasters 41 3 52 Saving the device configuration esse 42 3 6 Firmware updale prede teen devin es eee pat erste ret o det ge 43 3 6 1 NEP MT CI c mE 43 3 6 2 SRT PR sit eee E on pei dre ER LEUR 43 3 6 9 Via 50 iiio oe nta ne RI eec Rte 43 3 649 Via BOOIP TETP d endis D ee Datus 44 3 7 Operating modes of the device sees 45 3 7 1 Operating mode access point s sse 45 3 7 2 Operating mode client esessssseeeeeeenneneeennen nenne 46 3 7 3 Operating mode repeater 49 3 7 4 Operating mode machine admin 52 7179 en 04 PHOENIX CONTACT 5 FL WLAN 5100 3 8 PROFINET assistance 54 3 8 1 WLAN in PROFINET applications 54 3 9
80. ng a voltage reset for the device 3 6 3 Via SD card Make sure that the desired firmware version is located in the FLConfig folder The new firmware file is a pxc file e Switch off the device on which you wish to install the new firmware e g by interrupting the power supply e Now insert the SD card into the device e Switch on the device with the card inserted LEDs A D form a light sequence and indicate that the firmware is being downloaded After rebooting the new firmware version is available 7191 en 03 PHOENIX CONTACT 43 FL WLAN 510x 3 6 4 Via BootP TFTP This update method is used if the firmware on the device is no longer compatible in terms of function and a new version needs to be installed Make sure that your PC has an active BootP and TFTP server Configure the TFTP server with the IP addresses assigned via BootP Place the desired firmware image in the corresponding folder of the TFTP server Connect the device and your PC via an Ethernet cable Switch off the device on which you wish to install the new firmware e g by interrupting the power supply Switch on the device while holding down the MODE button Do not release the button until the LEDs change from yellow to green 44 PHOENIX CONTACT 7191 en 03 Startup and configuration 3 7 Operating modes of the device The device supports Access Point Client Repeater and Machine Admin
81. o the cluster then appears in the Cluster Configuration window They can be identified by their IP address or MAC address 60 PHOENIX CONTACT 7191 en 03 Startup and configuration FL WLAN 5100 amp PHEN X B t Clustering Enabled i Cluster Group Manage Cluster Group Cluster Group Name test cluster FL WLAN 5100 Device Name IP Address MAC Address Band Mode Channel Output Pd FL WLAN 5100 192 168 0 101 00 A0 45 37 1F CC 2 4GHz 802 7 2 442GF v 17 dBm Information FL WLAN 5100 192 168 0 104 00 15 61 10 58 E2 2 4GHz 802 7 2 442GF v 17 dBm Help amp Documentation Device Status Interface Status Alarm amp Events Connected Devices Configuration Quick Setup Network WLAN Advanced WLAN Cluster Configuration Serice System Local Events Network Events Diagnostics Channel Allocation FL WLAN 5101 FL WLAN 5100 192 168 0 100 192 168 0 102 00 0 45 02 2 4GHz 802 v 7 2 442GF v 17 dBm 00 A0 45 36 E9 CE 2 4GHz 802 7 2 442GF v 17 dBm ja lv Figure 3 12 List and configuration options for the cluster created The parameters that can be adjusted individually if necessary to achieve full wireless coverage can be edited in the table frequency band channel and transmission power The number of WLAN clients connected to the relevant access point can be
82. ode Repeater Mode Repeater Mode Ethernet Figure 3 3 Communication via a repeater chain enables WLAN coverage for complex topologies and connection at various locations Properties repeater acts as a logical dual device with a client FTB and an access point The repeater can therefore connect to every AP A All access points run on the same WLAN channel In repeater mode the data rate is at least halved as each data packet is received and sent coverage area of a WLAN network is enlarged configuration matches that of a client Only with PSK encryption 7191 en 03 PHOENIX CONTACT 49 FL WLAN 510x a 3 7 3 1 First a FL WLAN 510x must be configured as an access point The device settings mainly determines the encryption the SSID and the wireless channel with which the entire repeater system operates The other devices which are configured as repeaters below search for this SSID on all wireless channels Configuration of repeater mode 3 7 3 1 1 The configuration of an access point is described in Operation as an access point on page 34 Only WPA PSK TKIP WPA2 PSK AES or no encryption can be selected as the security mode Configuration of the access point In order to reach full data throughput under WLAN 802 11n WPA2 PSK AES encryption must be used 3 7 3 1 2 Configuration of the repeater In the WLAN menu Repeater is
83. on Next and perform a voltage reset Step 5 Assign IP Address The program attempts to transmit the IP parameters set to the device Phoenix Contact IP Assignment Tool Assign IP Address Attempting to Assign IP Address The wizard is attempting to Assign the specified IP Address Attempting to assign MAC Address LL 00 a0 45 04 08 a3 If it has been more than a minute or two and the IP is still not assigned please try rebooting or power cycling your device the following IP Address 192 168 1 21 IP Mask 255 255 255 0 IP Gateway 0 0 0 0 Once your device has received it s IP Address this wizard will automatically go to the next page Abbrechen Figure 3 4 Assign IP Address window Following successful transmission the next window opens Step 6 finishing IP address assignment The window that opens informs you that IP address assignment has been successfully completed It gives an overview of the IP parameters that have been transmitted to the device with the MAC address shown To assign IP parameters for additional devices e Click on Back 7191 en 03 PHOENIX CONTACT 27 FL WLAN 510x To exit IP address assignment e Click on Finish 3 2 6 Using the digital input and output The functions of the input output are generally available or need to be activated by the user by means of configuration The following table shows the possible options Please note that the majority
84. ower device operation must be approved or registered in some countries Furthermore there may be a usage restriction on the transmission power An up to date list of the country registrations can be found in the e shop at phoenixcontact com Make sure you observe the regulations of the relevant regulatory domain for device operation in all countries Approvals for other countries are available on request 1 2 2 FL WLAN 5101 The FL WLAN 5101 device Order No 2701093 does not have CE approval and may not be operated in Europe It is only available for export In addition the following approvals have been performed and passed for the FL WLAN 5101 device Order No 2701093 FCC CFR 47 Part 15 USA RSS 210 Canada 1 2 2 1 FCC information FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications 7191_en_03 PHOENIX CONTACT 9 FL WLAN 510x However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to r
85. packets are classed as high priority based on their Ethertype value Strict prioritization is used Non PROFINET traffic is now limited to a maximum data throughput of 10 Mbps 56 PHOENIX CONTACT 7191 en 03 Startup and configuration 3 11 Cluster management For the simplified configuration of larger WLAN networks the FL WLAN 510x offers cluster management This functionality enables WLAN access points within a network to be configured clearly and quickly They are grouped together into a cluster 3 11 1 Searching and selecting cluster devices To configure a cluster call a WLAN access point which you intend to add to the cluster via the corresponding IP address The other FL WLAN 510x devices are connected to this device via the cable based Ethernet network They are in Access Point mode Only FL WLAN 510x series devices can be grouped into a cluster The access point whose web interface you are viewing is fully configured These parameters are later transferred to all access points that belong to the cluster Parameters can also be modified later some individually for each device The Clustering parameter must be activated default in the Cluster Configuration menu in order to apply the configuration Clicking on Manage Cluster Group opens the Cluster Group Configuration pop up window 7191 en 03 PHOENIX CONTACT 57 FL WLAN 510x First enter a name for the future cluster under
86. re three antenna connecting cables the necessary DIN rail 144 mm plus cable feed throughs The WLAN access point is not supplied as standard Housing dimensions of FL RUGGED BOX OMNI 1 Width 180 mm Height 250 mm Depth 140 mm Figure 2 8 IP65 protective housing with antennas and cable feed throughs Additional rugged box versions can be found at phoenixcontact com FL RUGGED BOX Order No 2701204 FL RUGGED BOX OMNI 2 Order No 2701439 FL RUGGED BOX DIR 1 Order No 2701440 2 1 2 7 Antenna mounting distances The WLAN 510x supports the MIMO multiple input multiple output antenna technology Up to three antennas are used which are connected to connections X5 X6 X7 The antennas should be connected via an antenna cable outside the control cabinet so they can radiate 7191 en 03 PHOENIX CONTACT 17 FL WLAN 510x well into the area This means that the radiating element of the antenna should not be located too close to conductive objects if possible Keep a distance of more than 200 mm if possible Smaller distances are possible however they may affect radiation 9 Figure 2 9 Correct and wrong antenna mounting using an omnidirectional antenna as an example Distance of the antennas from one another The distance between the three antennas of a device must at least be 80 mm each to ensure decoupling of the data streams that are transmitted in parallel MIMO technology If larger distances of approxi
87. rnet All manufacturers K Ethernet Figure 3 15 Diagram single client mode Properties Transparently connects an Ethernet device to the access point on Layer 2 via WLAN 3 7 2 2 1 Automatic SCB Itis not necessary to manually enter the MAC or IP address of the connected device in the FL WLAN 510x It requests these automatically Only one cable based device may be connected in SCB mode Example of static IP An Ethernet device L2 with static IP address is connected to the copper port of the FL WLAN 510x in SCB mode A ping is sent or the IP address of the Ethernet device L2 behind the client is addressed via a browser from the PC that is connected to the access point on the other side A broadcast is sentto all devices Device L2 responds The first response ARP reply is not sent back via the WLAN wireless interface of the FL WLAN 510x This means a timeout is received on the PC side following the first ping browser call i e not a response All other calls are answered Old ARP tables in the PC can be deleted with the arp d command to ensure that the ARP request is resent If necessary delete the browser cache Example of DHCP BootP DCP Ifthe Ethernet device L2 is running in DHCP mode the MAC address is always transmitted to the FL WLAN 510x and beyond If several Ethernet devices are connected in automatic SCB mode it is possible that the MAC address of an unwanted device will b
88. rst time you use the device in order to avoid unauthorized access to the web interface 7191 en 03 PHOENIX CONTACT 39 FL WLAN 510x 3 5 SD card for saving the device configuration The FL WLAN 510x uses an SD card as an external storage medium The SD card can be used to back up the device configuration and to transfer the configuration to other devices Only SD cards from Phoenix Contact can be used see Ordering data on page 89 Do not delete the existing license key on SD cards from Phoenix Contact The device can be operated with or without an SD card The SD card must have a minimum memory capacity of 256 Mbyte The SD cards can be read and written by a PC Additional data project data which is not needed or used by the device can also be archived on the SD card After you have saved the configuration the SD card has the following structure SD card Figure 3 11 Fro Configuration nfig Image Recovery Configuration il Image Licence xxxxxx id pxc XXXXXx nwt pxc Utils XXX yy Documentation Tools FDCML GSD Structure on the SD card 40 PHOENIX CONTACT 7191 en 03 Startup and configuration 3 5 1 Inserting the SD card Insert the card into the device as shown in the figure below until it engages with a click NOTE If an SD card with a configuration file is inserted w
89. rver 0000 Secondary SNTP Serve 0000 Manual time set click to set time UTC offset 00h UTC GMT Lon v Current system time 12h 44m 27s Last SNTP synchronisation not synchronized Figure 6 2 System Time web page For the times the event table for example make sure that the system time corresponds to Greenwich Mean Time The current local time is based on the system time and the UTC offset Where necessary the switch between daylight savings and standard time must be taken into consideration Configuration sequence e Activate the SNTP function enable e Set the desired time zone with UTC offset e Select the operating mode Choose between Unicast mode the client receives its time from a fixed SNTP primary server Broadcast mode the client receives its time from broadcast messages which were transmitted by an NTP server and sent to several clients Manual configuration the module has a realtime clock with buffer battery This means that the clock continues running even without an external power supply Manual configuration is recommended for the certificate to be validated Please note that it is not possible to automatically switch between daylight savings and standard time 96 PHOENIX CONTACT 7191_en_03
90. s that can be used in the 2 4 GHz and 5 GHz band see Indoor checkbox are scanned for access points 7191 en 03 PHOENIX CONTACT 37 FL WLAN 510x Scan for Access Points Network Name SSID MAC Address Security Channe Signal Adopt PxC Guest 00 11 88 A0 DD F1 none 36 Adopt al Stefan 00 A0 45 37 25 10 none 6 Adopt PxC Guest 00 11 88 0 00 9 1 Adopt PxC 00 A0 45 EE EE 02 WPA2 PSK 7 Adopt PxC User 00 11 88 5A E6 18 WPA2 Radius 5 Adopt PxC 00 A0 45 37 1F CC WPA2 PSK 4 Adopt Rescan Figure 3 10 Display of WLAN access points received by the client A list of the WLAN access points found is displayed in a separate window The SSID for setting the client can be applied by clicking on Adopt The key must be known and entered as described below Indoor checkbox When set the Indoor checkbox means that the outdoor frequencies of the 5 GHz band are not scanned This significantly reduces the scan time For regulatory reasons not all frequencies in the 5 GHz band may be used outdoors If your WLAN application is located outdoors and is operated in the 5 GHz band uncheck the Indoor checkbox Specific operating modes are prescribed by law forthe 5 GHz frequency range in the case of outdoor operation Please make sure that the correct country settings are also used on the WLAN access point side Encryption WLAN Security WPA2 PSK AES offers the highest security sta
91. se of a radio link In client mode the current signal strength value of the connected access point or repeater is displayed graphically and dynamically in the Diagnostics RSSI Graph menu The RSSI Radio Signal Strength Indication value indicates the signal strength of the connected access point at the client location in dB The MAC address of the connected access point and the current WLAN signal strength RSSI are displayed at the top of the window FL WLAN 5100 amp 3 RSSI Graph Connected to AP 00 0 45 36 9 36 Signal Strength RSSl 13 dBm 0 FL WLAN 5100 20 Information Help amp Documentation Device Status Interface Status Alarm amp Events Configuration 60 Quick Setup Network WLAN Advanced WLAN Cluster Configuration Service System Local Events Network Events Diagnostics RSSI Graph 80 by CortctGmbHaco KG and Otter Figure 5 1 Display of the current WLAN signal strength on the client 7191_en_03 PHOENIX CONTACT 83 FL WLAN 510x a The value is only displayed and updated while the web page is open When the web page is closed the display is cleared Another option for dynamically displaying the signal strength of the access point on the client can be found in the Interface Status WLAN menu Here the Show signal bar checkbox must be activated see Figur
92. selects a WLAN channel Note if the device is operated outdoors in the 5 GHz band outdoor mode must be activated This information is valid for Europe WLAN Security WPA2 PSK AES offers the highest security standard Other encryption options are available in the WLAN section In order to reach full data throughput under WLAN 802 11n WPA2 PSK AES encryption must be used Passkey Key during the initialization of WPA encryption Note for maximum security arandom alphanumeric string up to 63 characters should be used Letters numbers and the following characters are permitted amp _ lt gt The password must contain at least eight characters Administrator Password It is recommended that you enter a new password to prevent any manipulation of the device The new password must be between 8 and 14 characters long The new password is not activated until you log out and log back in again Retype Password Retype the new password you wish to use 72 PHOENIX CONTACT 7191 en 03 Menu functions Table 4 1 Parameter list for Information page Designation Network configuration Description Type of IP address assignment Static a static IP address is assigned to this interface BootP during initial startup the device transmits BootP requests without interruption until it receives a valid IP address As soon as it receives a valid IP a
93. signment bootp FL WLAN 5100 E Country Regulatory Domain Germany ss Figure 3 5 Web page with overview icons Meaning of the individual icons Table 3 5 Meaning of the icons Icon Meaning PR The WLAN interface is deactivated X The device is in Client mode and there is no WLAN connection to x an access point at present The device is in Client mode and connected to an access point The bars indicate the signal strength of the access point for reception One bar poor link quality Two bars good link quality Three bars optimum link quality Four bars excellent link quality Connected clients The device is in Access Point mode and connected to a number of clients The number of connected clients is displayed If O is displayed there is no connection to a client Connection status connected VY Indicates whether the PC with the browser has an active connection to the device Connection status disconnected 4 During a configuration change in the event that a configuration change has been made via WLAN and the connection has been disabled An administrator is logged into the device The icon also acts as the 3 logout button s An administrator is not logged in at present The icon also acts as e the login button The active configuration differs from the saved configuration for the device To save the active configuration simply click on the ico
94. ss channel 40 MHz operation of the device on two wireless channels channel bonding As such an increased data rate is achieved but two wireless channels are used Static MAC Filter As an additional security criterion for restricting access the MAC addresses of devices can be used here to permit or refuse access Please note that WPS cannot be activated if using a MAC filter Roaming search list Selecting a limited number of channels reduces the client scan time when searching for another access point and speeds up roaming Transmit data rate Limits the data rate to a maximum 802 11f APP Exchange of roaming information between access points Should be activated deactivation may be necessary when using seamless roaming clients WiFi Protected Setup Wi Fi Protected Setup WPS supports simplified client security configuration Clicking on Activate WPS activates WPS for 120 seconds Please note that WPS cannot be used in conjunction with MAC filters STBC Space Time Block Coding is a method for increasing transmission resilience by means of redundant transmission paths in standard 802 11n STBC must be supported by the client RTS CTS threshold Packets whose size exceeds the specified value are transmitted with an acknowledgment mechanism in order to avoid collisions The total bandwidth of the WLAN can be increased if several clients use the same access point The value 2312 deacti
95. status can be tracked by observing the yellow LEDs A B C D the boot process is completed when the last LED goes out You then have 5 seconds to switch the device to configuration mode via the MODE button Push the MODE button for about 1 second in order to switch the device to configuration mode The yellow flashing LED A indicates that the device is in configuration mode If the MODE button is not pressed for an extended period in active configuration mode configuration mode is exited automatically after 5 minutes and the device is started with its previous settings Select the desired operating mode by pressing the MODE button until the corresponding LED combination lights up Once you have scrolled through all the LED combinations operating modes the selection automatically starts again from the beginning After selecting the desired operating mode exit the configuration by pressing the MODE button for about 1 second until the four LEDs light up The mode is set and the device starts up with the corresponding settings During configuration with the MODE button not all parameters are rewritten only those necessary for the operating mode Some settings can therefore be made beforehand via the web interface or via SNMP and will still be effective after configuration with the MODE button Ifthe module has been previously configured we recommend restoring the device s default settings before configuring the device
96. t only channel 1 11 can be operated Selection of other channels is not possible This device and its antenna s must not be co located or operation in conjunction with any other antenna or transmitter Under Industry Canada regulations this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for the transmitter by Industry Canada To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that necessary for successful communication This radio transmitter identify the device by certification number or model number if Category 1 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated Antenna types not included in this list having a gain greater than the maximum gain indicated for that type are strictly prohibited for use with this device The device could automatically discontinue transmission in case of absence of information to transmit or operational failure Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology Dynamic Frequency Selection DFS for devices operating in the bands 5250 5350 MHz 5470 5600 and 5650 5725 MHz The maximum antenn
97. t there is only one firmware image on the device If however the switchover procedure described here is carried out the device will no longer start as there is no firmware image present This can be seen when the four link quality LEDs do not go out one after the other In this case the switchover procedure must be repeated again so that the device is started with the original firmware image For information on how to load a second firmware image please refer to Firmware update on page 43 The device can accommodate two complete firmware versions dual image You can Switch between these two versions To do this proceed as follows e Switch off the power supply e Press and hold down the MODE button e Switch on the power supply e Release the MODE button within five seconds once the link quality LEDs A B C D have started to flash yellow The device now switches the firmware image and reboots 7191 en 03 PHOENIX CONTACT 23 FL WLAN 510x 3 2 3 Connection to a PC Proceed as follows to connect the WLAN 510x to your PC via the Ethernet interface without using BootP default setting Connect the device to a power supply Press the mode button right after the booting LED A D off until LED A flashes Press the MODE button briefly several times to select mode BC LED Confirm the mode by pressing the MODE button longer gt 2 sec The temporary DHCP server automatically assigns an IP address
98. t passphrase Figure 3 7 Administrator Password Retype Password Quick Setup web page 2 7191_en_03 PHOENIX CONTACT 33 FL WLAN 510x 3 4 1 Operation as an access point In access point mode the WLAN 510x forms the wireless interface in the overall network for one or more WLAN clients Network SSID The network SSID is used to identify the network to which the WLAN clients connect wirelessly The name entered here for an access point enables all WLAN clients with the same SSID to connect to the access point using the correct encryption The network name can be up to 32 characters long Letters numbers and the following characters are permitted amp _ lt gt WLAN Band The wireless frequency at which the WLAN network is operated is specified at the access point Under WLAN Band first select whether your network should be operated in the 2 4 GHz band or in the 5 GHz band In doing so observe any company specifications for frequency planning Channel 2 4 GHz band Where possible you should select a free frequency or observe any specifications relating to the company premises Channels 1 6 and 11 are typically used in order to avoid interference between devices caused by channel overlap 5 GHz band Operation inside buildings Indoor Ch36 Ch48 in this area one of the four channels can be freely selected and is available without any interruptions
99. te of the device while itis being configured using the MODE button For details see the sticker on the side of the device or Configuration using the MODE button on page 21 In WLAN operation as a client the LEDs indicate the signal strength of the connected device see Meaning of the LEDs as signal quality indicators in client mode on page 21 Fail Lights up red if no configuration has been received in WPS mode the link quality LEDs also flash yellow WLAN status WLAN connection established blue Whether data transmission occurs depends on whether the passwords and certificates are valid WLAN connection can therefore exist even if data cannot be transmitted If WLAN authentication fails this is indicated in the log file Half duplex data transmission blue if flashing data transmission is active 20 PHOENIX CONTACT 7191_en_03 Startup and configuration Connection establishment purple only in client mode during a scan connection establishment or when a channel is selected automatically in access point mode Green LED if the WLAN interface is in idle mode e g between scans in client mode or when the radar check is performed at 5 GHz in access point mode Dig OV R status green yellow see Meaning of the LAN1 2 indicators on page 21 LANe status green yellow see Meaning of the LAN1 2 indicators on page 21 DI digital input set at connector X3 see Using the digital input and o
100. the gateway in format 0 0 0 0 Lease time WLAN WLAN Configuration Basic settings Time interval in seconds during which the IP address is valid Activate WLAN interface The disabled WLAN interface prevents any communication at the wireless interface 7191 en 03 PHOENIX CONTACT 73 FL WLAN 510x Table 4 1 Parameter list for Information page Designation Description Operating mode Access point implements a WLAN wireless network for wirelessly connecting WLAN compatible devices to an Ethernet network Client supports the wireless connection of Ethernet devices to an Ethernet network via a WLAN wireless network FTB mode Fully Transparent Bridge Supports Layer 2 transparent communication with multiple devices behind the WLAN client SCB mode Single Client Bridge Layer 2 transparent communication with one device behind the WLAN client compatible with all access points MCB mode Multi Client Bridge Layer 3 TCP IP transparent communication with multiple devices behind the WLAN client compatible with most access points Repeater Access point with wireless connection to another access point via virtual client Machine Admin In addition to access point functionality this access enables another specific service access via WLAN It is restricted to a specific IP address in the network Confirming this mode with Apply amp Save enables Machin
101. us Interface Status Alarm amp Events Connected Devices Configuration Quick Setup Network WLAN Advanced WLAN Cluster Configuration Service System Local Events Network Events Diagnostics Channel Allocation Copia by Phoe al ContactGmbH amp Co hG and Otter Network SSID WLAN Band Channel WLAN Security Passkey Administrator Password Retype Password Ear A 2 4GHz 802 11 b g n v Channel 2 442GHz WPA2 PSK AES vj me m Show cleartext passphrase Figure 3 8 Device configuration as a client Client FTB mode is recommended when using another FL WLAN 510x as an access point Other client modes are described in Operating modes of the device on page 45 Confirm your selection with Apply or Apply amp Save The WLAN wireless interface is activated automatically by clicking on Apply in the Quick Setup menu It is deactivated by default 36 PHOENIX CONTACT 7191_en_03 Startup and configuration FL WLAN 5100 xs YY GE E 968 Quick Setup Web management language English IP Address Assignment bootp FL WLAN 5100 Information Help amp Documentation Device Status Interface Status Alarm amp Events Connected Devices Configuration Quick Setup Network WLAN Advanced WLAN Cluster Con
102. utput on page 28 US supply voltage present 3 1 1 Meaning of the LAN1 2 indicators Table 3 1 Meaning of the LAN1 2 indicators Des Color Status Meaning LAN 1 OFF No Ethernet connection at port 1 Green ON Ethernet connection in full duplex mode Flashing Ethernet communication in full duplex mode Yellow ON Ethernet connection in half duplex mode Flashing Ethernet communication in half duplex mode LAN 2 OFF No Ethernet connection at port 2 Green ON Ethernet connection in full duplex mode Flashing Ethernet communication in full duplex mode Yellow ON Ethernet connection in half duplex mode Flashing Ethernet communication in half duplex mode 3 1 2 Meaning of the LEDs as signal quality indicators in client mode Table 3 2 Meaning of LEDs A to D in client mode LED Meaning OFF No WLAN connection A Poor link quality A B Good link quality A B C Optimum link quality A B C D Excellent link quality 3 2 Configuration using the MODE button Typical operating settings for the FL WLAN 510x can be set using the MODE button on the front of the device The possible settings can be found in table Operating modes on page 22 A selection of the key settings is also available directly on the device 7191_en_03 PHOENIX CONTACT 21 FL WLAN 510x Table 3 3 3 2 1 General sequence Connect the device to the power supply The device is started and the
103. vates RTS CTS 0 activates it for all packets Fragmentation Data packets whose size exceeds the specified value are fragmented In RF environments with a lot of interference the number of repeated packets can therefore be reduced The value 0 deactivates fragmentation Long distance mode 3000 m Wireless connections over large distances 3000 m require the timeout configuration to be modified Change this parameter only if the distance is over 3000 m The setting must be the same for the access point and the client 76 PHOENIX CONTACT 7191 en 03 Menu functions Table 4 1 Parameter list for Information page Designation Description Antenna configuration Cluster Configuration Cluster Configuration Selection of the desired antenna connections X5 X6 X7 Only activate the connections to which an antenna is connected Activated antenna connections can be damaged if an antenna is not connected Terminate unused connections with 50 ohms Clustering Clustering can be used to configure several access points inthe same subnetwork for one WLAN network centrally as a group The parameters marked with are then synchronized automatically between all access points belonging to the cluster Cluster Opens a window in which you can configure the cluster Cluster Name Name of the cluster can be configured under Cluster Cluster Configuration
104. via the MODE button This action is also performed via the MODE button This ensures that the initial configuration is recognized Operating modes Mode Description LEDs gt Ww O 1 Exit configuration mode without modifying the configuration A e 2 Restoring default settings factory defaults PROFINET assistance mode allows DCP Discovery Control Protocol to be used in PROFINET environments PROFINET data is transmitted with top priority see PROFINET assistance mode on page 54 A B Static IP temporary DHCP server as a DHCP server the device An address is assigned only once in order to easily supply a single device with an IP address e g a PC that is connected for configuration purposes In this mode the device can be accessed under IP 192 168 0 254 assigns an IP address to a device connected via the Ethernet network B C 22 PHOENIX CONTACT 7191_en_03 Startup and configuration Table 3 3 Operating modes LEDs A B c D Mode Description 7 Restoring IP setting to default setting BootP request through to A B C assigning IP address The other settings specifically made on the device are retained 8 Restoring the device to the basic settings specified by the user D o 9 WPS client A D e e D 3 2 2 Changing the firmware image using the MODE button NOTE By defaul

Download Pdf Manuals

Related Search

Related Contents

Manual de instrucciones  資料1 - 南砺市  Operator`s Manual The Bullet Blender™  取扱説明書 - Cateye  ファン・ポンプ（2乗低減トルク負荷）用インバータ  平成4年広審第122号 漁船第五十三瑞恵丸機関損傷事件 〔簡易〕 言渡  Concur Mobile App for BlackBerry    KP 500 / KP 660 Betjeningsvejledning Instructions  Design House 517706 Installation Guide  

Copyright © All rights reserved. Failed to retrieve file