20-740 - Security
Contents
1. Click Ea button to add a certain day schedule click kii button to delete the selected schedule Step 3 You can also double click the grid to pop up a week schedule window SCHEDULE x Start Time End Time Start Time End Time vY x Delete Select day and then click Add button to setup the start time and end time Then select other days and click Copy button to save the setting to other days Finally click OK button to save week schedule Step 4 Select other channels and set timeline for them or select Apply Settings To All Channel and click Copy button to set the same settings for all channels 7 3 Motion Based Recording Motion detection based recording when there is a motion event detected the camera will be triggered to record To Setup Motion Based Recording Step 1 Enter into Menu gt Setup gt Schedule gt Motion tab The setup steps for 4 8 CH DVR Quick Start Guide schedule for motion based recording are similar to normal schedule setup You can refer to 7 2 Schedule Recording for details Step 2 Enter into Menu gt Setup gt Alarm Motion Motion tab as shown below MOTION Schedule Setting Setting f Setting Setting Setting Setting Setting Setting Default Step 3 Enable motion alarm Please specify to channel and click Apply to save settings Step 4 Click Setting button under the Area to set Sensitivity and Detection area L2. Password Default e Input IP address Subnet Gateway If using DHCP please enable DHCP in both the DVR and the router Enter into Menu gt Information gt Network and user can check the network settings of the DVR e Enter into Record Setup to set network video parameters like resolution frame rate etc e Open IE on a computer on the same network Input the IP address of the DVR in IE address bar and press enter If HTTP port is not 80 add the port number after IP address e JE will download ActiveX component automatically Enter the username and password in the subsequent window 10 2 Access DVR on WAN 1 Connect the DVR to internet through router or virtual server e Please enter into Menu gt Setup Network Setup as shown above e Input IP address Subnet Gateway If using DHCP please enable DHCP in both the DVR and the router e Forward IP address and port number in Virtual Server setup of the router or virtual server Configure the firewall to allow accessing the DVR If the user has enabled the UPnP function in both the DVR and router he can skip this step Please refer to the relevant chapter for more details e Open IE browser input IP address or dynamic domain name and enter If HTTP port is not 80 add the port number after IP address or domain name e JE will download ActiveX automatically Then a window pops up and asks for user name and password Input name and password correctly and enter to view 2 Connec
3. You can check your HDD information through this tab If your HDD was recently installed select the HDD from the list to format it Click Next button This will let you see your DVR status And then Click Finish button to end this wizard You can also refer to the complete setup steps from the relevant sections of DVR User Manual If you don t want to setup Wizard please click Exit button to exit 5 Login After you exit the wizard setup you can login to the DVR Long press ESC Stop key can switch the output among CVBS VGA and HDMI Press the MENU button which will bring the LOGIN dialogue box and enter the user name admin and password 123456 LOGIN x User Name admin Password E Login Cancel 6 Main menu setup 4 8 CH DVR Quick Start Guide Click right mouse or press ENTER button on the front panel to enter into the main menu Then click Setup to enter into Setup interface as shown below SETUP A Live Record Schedule SE e amp Mi Network Users 4 Advanced Basic configuration Users can set video system menu language audio time and authorization check Live configuration Users can set name time display picture color and hide cameras Record configuration Users can set record quality frame rate resolution time stamp and recycle Schedule configuration Users can set schedule for timer motion detection and sensor alarm respectively Alarm confi
4. In order to take images on alarm the snapshot feature should be activated in Alarm Handling for different kind of alarms Please refer to 4 5 Alarm Configuration for details 9 Back up This unit supports backup by USB flash DVD writer and USB HDD Step 1 Enter into Menu gt Backup tab BACKUP nd Time 3 21 2013 15 12 0 13 21 2013 15 12 04 J3 2142013 15 12 04 J342142013 15 12 04 Step 2 Set the start amp end time select channels and click Search button to display the searched data in the data backup list box Step 3 Select a required file or checkmark All to select all data files Click Backup button to pop up Backup information window Step 4 In the backup information interface user can check the relevant options for backing up files These options include storage Media backup player and save file type Then click Start button to start backup 10 Remote Surveillance In order to view the DVR from a network it must be connected to a LAN WAN or internet The network setup should be done accordingly 10 1 Access DVR on LAN e Please enter into Menu gt Setup Network Setup as shown below 4 8 CH DVR Quick Start Guide NETWORK Network Sub stream Email Server Other Settings Server Port lsoss Obtain an IP address automatically IP Address Subnet Mask Preferred DNS Server 192 168 011 001 Alternate DNS Server 000 000 000 000 PPPoE Gateway 192 168 011 001 User Name
5. click Apply to save settings SENSOR f Alarm Handling Schedule Enable Type Name lt SENSOR 1 SENSOR 2 Z lt SENSOR 3 S SENSOR 4 Default Step 4 Enter into Menu gt Setup gt Alarm Sensor gt Schedule tab to bring up schedule settings for sensor alarm The setup steps are similar to normal schedule setup You can refer to 7 2 Schedule Recording for details Note The timelines of the two schedules must match otherwise you cannot get the record in some time 8 Playback This unit supports four kinds of playback 8 1 Live Playback Click Play gt button on the main menu bar to playback the record User can do concrete operation by clicking the buttons on screen 4 8 CH DVR Quick Start Guide CAMERA 02 SMES r 022772012 10 24 50 02 27 2012 10 24 30 3 Ps i bo 4 E z HH Q te Camera Nami 4 x gt K 02 07 2012 10 24 26 gt gt 1X 10 29 30 8 2 Playback by Time Search Step 1 Enter into Menu gt Search gt Time Search tab Step 2 Select date and channels on the right hand side and press Search button A date with highlighted borderline indicates presence of data Step 3 Set the start time by clicking a particular grid or by entering the specific value in the start time field Step 4 Select the channel display mode and click i button to play record Use the playback toolbar to control the playback SEARCH 8 3 Playback by Event Search Step 1 En
6. to external alarm Connect to external sensor1 8 En 8 ch SDI video inputs Connect to speed dome Y is TX a 10 Connect to high definition display device is TX Connect to keyboard A is TX 11 VGA port Connect to monitor B is TX To connect external USB devices like USB flash USB Audio output connect to the HDD for backup or update firmware or connect to sound box USB mouse CVBS video signal output 4 ch audio inputs 3 Startup amp Shutdown 3 1 Startup Step 1 Connect to cameras and monitor Step 2 Connect with the source power Step 3 The device will boot and the power indicator will turn blue Step 4 A WIZZARD window will pop up 3 2 Shutdown 4 8 CH DVR Quick Start Guide You can shut down the device by using IR remote controller and mouse By IR remote controller Step 1 Press Power button This will bring up a shutdown window The unit will shut down by clicking OK button Step 2 Disconnect the power By mouse Step 1 Enter into Menu and select Shut Down icon This will take you to a shutdown window Step 2 Click OK Then the unit will power off after a while Step 3 Disconnect the power 4 Setup Wizard After the device starts a setup wizard pops up You can set up time network record and disk management WIZARD Device Name Language English Date Format MM DD YY Time Format Time Zone MT System Date 03 4 24 2012 BH System Time 16 40 4
7. 9 Startup Wizard lt Next Exit Click Device name box to pop up a keyboard as follows It supports digits alphabets and symbols as inputs Click Shift button to input Capital letters and symbols click Shift button again to return Click Next button to bring up a network setup window WIZARD HTTP Port Server Port 6036 Obtain an IP address automatically IP Address 192 168 011 061 Subnet Mask 000 000 000 000 Gateway 192 168 011 001 Preferred DNS Server 192 168 011 001 Alternate DNS Server 000 000 000 000 Next Exit The default HTTP port is 80 The default server port is 6036 You can check Obtain 4 8 CH DVR Quick Start Guide an IP address automatically to acquire network information or input IP address subnet mask gateway preferred alternate DNS server manually This function is used to monitor DVR through internet See Section 10 for details Click Next button This will take you to record setup window WIZARD 1osop Higher 1536 kbps 7 Prey Next Exit Select resolution fps encode quality and max bitrate The higher the value is the clearer the recorded picture is Of course more space of HDD will be taken up Click Next button This will take you to the HDD management window WIZARD Type Size GB Free GB Status Properties Sources 01 IDE 0 00 0 00 Normal Read amp Write Local Refresh Format Next Exit
8. Quick Start Guide 4 8 CH DVR 4 8 CH DVR Quick Start Guide 1 Install Hard Drive amp DVD Writer 1 1 Install Hard Drive Notice 1 Support two SATA hard drives Please use the hard drive the manufacturers recommend specially for security and safe field 2 Please disconnect the power before being connected to other devices Don t hot plug in out Step 1 Unscrew and Open the top cover to connect the power and data cables Place the HDD onto the bottom case as Fig 1 1 Step 2 Screw the HDD as Fig 1 2 Fig 1 1 Connect HDD Fig 1 2 Screw HDD Notice 1 For the convenience to install please connect the power and data cables firstly and then screw to fix 1 2 Install DVD Writer Step 1 Unscrew and Open the top cover to connect the power and data cables Place the DVD writer onto the bottom case as Fig 1 3 Step 2 Screw the DVD writer as Fig 1 4 Fig 1 3 Connect the DVD Writer Fig 1 4 Screw the Writer 2 Rear Panel Instruction LAN uss DOIN 4 HM GA 1 2 345 9 10 11 12 1314 Rear Panel for 4 CH 4 8 CH DVR Quick Start Guide Alarm outputs connec 8 iO inputs Connect to high definition display device VGA output connect to monitor T E EE P pox 13 Connect external USB devices like USB flash i drive HDD Talk connect to microphone DC12V 4 3 2 1 ows AUDIO OUT r bd s z f Homi VeA p eresasni 7 Aare N HD SDI VIDEO IN 8 9 10 11 12 13 14 Rear Panel for 8 CH l l ch relay output Connect
9. eft click the grid and drag to delete the area Drag again to add area You can drag slide bar to set the sensitivity value 1 8 The higher the value is the more sensitive it is to motion Since the sensitivity is influenced by color and time day or night you can adjust its value according to the practical conditions Click EA icon to set the whole area as detection area Click icon to clear the set detection area Click icon to test the sensitivity as per the local conditions Once motion is sensed it displays a figure icon Click icon to save the setting Click icon exit current interface l i 03 21 2012 hss 20 Ms Sensitivity 6 Test Step 5 Enter into Menu gt Setup gt Alarm gt Motion gt Schedule tab to bring up schedule settings for motion alarm The setup steps are similar to normal schedule setup You can refer to 7 2 Schedule Recording for details Note The timelines of the two schedules must match otherwise you cannot get the record in some time 7 4 Sensor Based Recording To Setup sensor Based Recording 4 8 CH DVR Quick Start Guide Step 1 Enter into Menu gt Setup gt Schedule gt Sensor tab The setup steps for schedule for sensor based recording are similar to normal schedule setup You can refer to 7 2 Schedule Recording for details Step 2 Enter into Menu gt Setup gt Alarm Sensor Basic tab as shown below Step 3 Enable sensor alarm Please specify to channel select senor type and
10. guration Users can set sensor type alarm trigger and buzzer alarm Network configuration Users enable network function and configure IP address DDNS transmission video parameters here User configuration Administrator can add delete users and change their authorization PTZ configuration Users can set protocol baud rate address presets and auto cruise track here Advanced configuration Users can reboot the device and import amp export data into or from mobile storage medium 7 Recording Setup A user needs to install and format a HDD and set all the recording parameters before recording There are four kinds of record modes 7 1 Manual Recording A user can press REC button on the front panel after quitting system setup Press this 4 8 CH DVR Quick Start Guide button again to stop recording Or press REC button on remote controller Click it again to stop Or click REC button on the tool bar with mouse Click it again to stop 7 2 Schedule Recording To Setup Schedule Recording Step1 Enter into Menu gt Setup gt Schedule tab Refer to the following picture SCHEDULE Sane Motion Sensor 00 00 04 00 08 00 12 00 16 00 20 00 Sunday 8 28 a Monday A TT TT TT Tuesday aS a eo Pat a E Wednesday 11 1111 TTT E Tt tt tt I I Thursday E i al ae a Friday _ _ B RR a i Saturday TTT TTT TTT TT ETT EE ET TT Apply Settings To Channel Default Step 2
11. t the DVR to Internet through PPPoE e Enter into the DVR s Main Menu gt Setup gt Network interface to enable PPPoE 4 8 CH DVR Quick Start Guide and then input user name and password received from your ISP Next click Apply The DVR will connect to the server and would give a confirmation message e fusers want to utilize dynamic domain name please apply for a domain name in a DNS server supported by the DVR or router Then add to the DVR or router e When accessing the remote interface of DVR user can input WAN IP domain name to access directly user can enter into Main menu gt Information gt Network interface to check IP address The browser will download Active X control e The following steps are the same as the connection way above 450041000356 Al
12. ter into Menu gt Search gt Event Search tab 4 8 CH DVR Quick Start Guide Step 2 Select date and channels on the right hand side A data with highlighted borderline indicates presence of data Step 3 Then checkmark Motion Sensor or All accordingly You can search for motion based recording and sensor based recording Step 4 Press Search button to display the searched event information in the event list box Step 5 Double click the event item to play the record SEARCH Time Search Event Search File Management Image Start Time End Time 03 04 2013 09 44 52 3 04 2013 03 04 2013 09 44 52 3 04 2013 3 5 03 04 2013 09 44 52 3 04 2013 5 10 11 12 1718 19 2 5 26 27 gt 03 04 2013 09 44 52 3 04 2013 171 Vi Motion 8 4 Playback by Image Search Step 1 Enter into Menu gt Search gt Image tab SEARCH Time Search Event Search File Management mA Search Start Time 03 04 2012 9 00 00 00 End Time 03 f 04 2013 E25 Delete Lock Save Save All l4 4 gt gt Step 2 Select data and channels on the right hand side Step 3 Press Search button to search for a recorded image Step 4 Once an alarm image has been identified the user can double click the image to play the recording You can lock the image by clicking Lock button Click Save button to copy the image on the HDD Click Save All to copy all images on the HDD 4 8 CH DVR Quick Start Guide Note
Download Pdf Manuals
Related Search