Operating Procedures UL-P100 Series Underwater Light DANGER
Contents
1. ap S Va WARNING ZN Never operate this Underwater Light for more than 10 seconds unless it is totally submerged in water Without total submersion the light assembly will get extremely hot which may result in serious injury to pool users installers or bystanders or in damage to property ABe sure power is off before installing or removing lamp Allow lamp to cool before relamping This light fixture uses a Halogen Quartz lamp Do Not touch lamp with bare hand this may severely reduce its life Use the plastic furnished with the replacement lamp to eliminate finger prints from getting on lamp REPLACEMENT PARTS UL P100 Underwater Light Replacement Parts Item Part No Qty Description 1 040101 1 Color cover of lens 040102 Screw 040103 Face ring 040104 Cover 040105 Lens 040106 Lens seal 030132 040107 040108 Lamp 12 volt 100watt 040109 Lamp seal 040110 Mirror 040111 Dent head Sealing nut with screw 040112 Sealing o ring 040113 Body 040114 020107 040115 Bolt 040116 Mounting bracker Sealing nut with screw 040117 Mounting spacer UL P100 Series Underwater Light Operating Procedures PLEASE READ THE FOLLOWING CAREFULLY AND KEEP THIS USER MANUAL SAVE FOR FUTURE REFERENCE DANGER RISK OF ELECTRICAL SHOCK OR ELECTROCUTION This underwater light fixture must be installed by a licensed or certified electrician or a qualified serviceman in ac2. Consult the local Government Building Department to be certain that the pool s electrical system meets all applicable requirements B Perform the following steps after the electrical system requirements are met 1 Locate position on a vertical wall where light is to be installed The top of the light lens must be 45CM below normal water level see Figure 1 2 Connect conduit to midst of Mounting Spacer left of Bracket see Figure 2 3 If pool surface is to be plastered you must allow proper concrete cutback for plaster thickness Finish concrete surface must be flush with Mounting Spacer CAUTION Finish area surrounding Mounting Spacer MUST be flat and flush with the face of Mounting Spacer this ensures a snug fit between light and wall see Figure 3 4 After pool surface is finished trim the Conduit 5 Wrap a length of the cord up to a maximum of 2 4mt long on the back of the light assembly This extra cord allows you to bring the light out of the pool for relamping and servicing 6 Connect cord electrical wires at Junction box through Conduit be careful not to pull the 7S5mm 80mm of slack cord at the light through the conduit when connecting the wires 7 Connect all wires to the corresponding circuit wires in the junction box and feed paraffin 8 Secure the junction box cover in place 9 Before operating the light for more than 10 seconds fill pool until the Underwater Light is completely submerged in water To check for prope
3. cordance to the requirements of your government standard or local authorities Improper installation will create electric hazards which could result in serious injury death as well as damage to the property Before servicing the light disconnect the power supply from the circuit breaker Failure to do so could result in serious injury death and or damage to the property EMLI06083032 INSTALLATION A Preparatory steps which must be completed by the electrician before light is installed see Figure 1 ee MIN TO POWER SOURCE FEED PARAFFIN ATER LEVEL Ka 45CM MIN FROM WATER LINE TO TOP OF LENS A on CONCRETE MUST BE CUT BACK AROUND NICHE TO ALLOW FOR A COMPACT PLASTER SEAL Figure 1 1 Ensure that the electrical system and its wiring for the pool conform to the requirements of your oe or your local authorities The installation of the Underwater Light should only be performed y a licensed electrician a The junction box or the low voltage transformer for 12 volt Underwater Light model is to be located at least 120CM from the edge of the pool see Figure 1 b The light fixture and all metal parts that are within 240CM of the poet must be properly protected with non ductile materials and that the connections must be waterproof c The mounting bracket must be properly installed so that the top edge of the Underwater Light lens is at least 45CM below the surface of the water in the pool see Figure 1 2
4. r operation turn on main switch or circuit breaker as well as the switch that operates the Underwater Light itself 10 Rotating Locking System ensures light is secured to bracket see Figure 4 C Winterizing Light should be left in place for winterization MOUNTING BRACKET DO NOT MOUNT ON DO MOUNT ON A vV CONDUIT REVERSE RADIUS IRREGULAR OR FLAT WALLS WITH NO TIGHTER SURFACE UNEVEN SURFACES SURFACE THAN 6 FT RADIUS AS VIEWED FROM TOP OPEN POSITION POSITION Figure 4
Download Pdf Manuals
Related Search