SW-2GT-2SFP 4-Port Gigabit Switch USER MANUAL
Contents
1. pair And the multi single mode fiber 1s connected to SFP module LC fiber connector Then optical transceiver works and the corresponding LED is ON for correct connection See the table below for the LED indicators FX I FXe Ce C re PWR Explanation for LED indicators 1000M LINK ACT TP 1 TPE LED indicators serve as device monitoring and trouble display The following is the explanation for each LED indicator 5 Connection status display for link n ON indicates that link is in correct connection Link Act Active status display of fiber port or RJ45 port in Blink indicates packet goes through switch correctly 1000M Transfer rate of electric interface is 1OOOMbps Notice VLAN TP 1 and TP2 port isolation mode NORMAL All port switching mode eo Main features 1 Auto negotiation function supports UTP ports to auto 10 100 1000M and Full Duplex Half Duplex 2 The SFP slot supports 1000Mbps 3 Supports flow control and broadcast storm protection 4 Itis low power consumption low heat and good reliability Technical parameters 1 Operating standards IEEE802 3z AB gt 10 100 1000Base T and 1000Base SX LX ZX 2 MAC address table 1K 3 Frame buffer memory 1MKb 4 Connector UTP RJ 45 10 100 1000Mbps SFP slot SFP 1 25G Module 5 Cable UTP Cat 5 or 6 UTP the max distance up to 100M Multi mode Fiber 50 125 gt 62 5 125 um the max distance up to 552. 0M Single mode Fiber 8 125 gt 8 7 125 gt 9 125 um the max distance up to 120M 6 Flow control Full Duplex IEEE802 3x flow control Half Duplex back pressure flow control 7 Ambient Temperature 0 50 C 40 85 C 9 Humidity 5 90 10 Dimensions 130x94x27mm e 8 Storage Temperature Cautions 1 This product is suitable for indoor application 2 Put on the dust cover of fiber interface when not used 3 It is forbidden to stare at the TX fiber transfer end with naked eyes 4 Single optical fiber or WDM transceiver must be used in pair eo Trouble shooting 1 Device is not matched Please select the corresponding network device according to the transfer rate of the product 1LOMbps or 1OOMbps 1000Mbps when connected to other network devices network card hub switch 2 Line loss is excessive during the fiber wiring Excessive loss in connector plug in and fiber soldering and excessive intermediate nodes may cause excessive loss rate or abnormal operation Megatel Industries Corporation 664 Wagner Court North Wales PA 19454 USA TEL 1 610 239 8812 FAX 1 215 699 3348 sales megatelindustries com www megatelindustries com VX egate
3. SW 2GT 2SFP 4 Port Gigabit Switch USER MANUAL Gigabit Ethernet Switch 10 100 1000Base T amp 1000Base X _ th Fi a E 8 8 e Brief introduction SW 2GT 2SFP is a 4 port Gigabit Ethernet Switch with 2 10 100 1000M Ethernet ports and 2 SFP 1 25G SFP slots End users can use different SFP modules such as 1000Base T 1000Base SX 1000Base LX etc The switch supports TEEE802 3U IEEE802 3z 1000Base Tx Fx protocol as well as full duplex and half duplex mode For optical SFP transceivers this switch supports any third party standard SFP modules from any SFP vendors 5 Packing List Please check the following items in the package before installing the unit 1 Unit 1 PCS 1 Copy SW 2GT 2SFP Ethernet Switch Power Adapter User Manual Please contact the dealer immediately for any loss or damage to the above items er Installation 1 Interface RJ 45 interface The transmission media adopts CATS twisted pair with typical length of 100 meters It features the function of automatically identifying the through line and cross wires Fiber interface LC is of duplex mode type including two interfaces namely TX and RX When the two sets of optical transceivers are interfaced or connected to switch the fiber is in cross connection namely TX RX RX TX direct butting for single optical fiber 2 Connection The network device work station hub or switch with RJ 45 interface is connected to RJ 45 jack through twisted
Download Pdf Manuals
Related Search