tpms1209t08-t user manual - Tire Pressure Monitoring System (TPMS)
Contents
1. 2 Installation of Security Lock Each transmitter has a security lock to prevent it becomes loose or falls off The security lock has 3 screw holes with screws As shown below h Security lock t Note Security Lock and Transmitter should be installed at same time If the user chooses to use the lock please refer to the below part of lock installation Installation step of the Security Lock 1 First connect the meshing parts of the Lock and the Transmitter to make them an integrated part and then screw the Transmitter together with the Lock firmly onto the valve as shown in the right figure 2 Lock the Transmitter Use the wrench to fasten the three bolts inside the sockets on the Lock Make sure they are fastened onto the valve Then the Transmitter can not be easily screwed off unless the three bolts are screwed off by using the wrench How to inflate the tire with a locked Transmitter Before inflating the tire please 1 Use the wrench to loose the three bolts 2 Screw off the Transmitter 3 Remove the Transmitter and the Lock V System Function of TPMS1209T08 T 1 Full time Monitoring Function TPMS1209T08 T can monitor the tire pressure and temperature whether the vehicle is running or parked Therefore to keep the driver informed of the tire state and realize full time monitoring 2 High Pressure Alarm Display mode Function the system will issue the high pressure alarm when the tir2. Please check the power connection 7 When connected with vehicle s continuous power supply will the power of storage battery be used up if the vehicle parks for a long period The current draw of the monitor is only 50 mA under normal state and this can be ignored However if the vehicle will not be used for 2 or 3 months the storage battery might be used up and the vehicle cannot be started So we suggest the user remove the storage battery if the vehicle will not be used for a long period 2d IX Warranty Terms Valid Warranty Card 1 The Warranty Card must be filled completely signed by and sealed by the authorized distributors of Sate 2 The Warranty Card is valid in the countries or regions where the purchase occurs 3 The Warranty Service requires user to offer the Warranty Card and the original invoice Warranty Condition Responsibility and Limitation 1 The product warranty period is one year and is subject to the time marked on the invoice 2 Any damages or faults due to improper use are not involved in the warranty commitment 3 Users are not allowed to open repair and refit the products by themselves otherwise the warranty service will be invalid 4 Injecting chemicals such as leak proof glue into the tire will damage the Transmitters and affect the system operation Do not use such articles after the TPMS is installed 5 The warranty does not include replacement of the enclosure and display panel
3. pressure and temperature on the screen The monitor can issue different alarms if the tire pressure is at an improper level so as to notify the driver to treat the problem timely Through TPMS1209T08 T the driver can keep the tire running under a proper pressure so as to avoid excess gasoline consumption and keep the vehicle in an easily controlled state II Parts of TPMS1209T08 T 1 Monitor Transmitter for each tire position purchased Transmitter lock for each tire position purchased 1 Mounting Bracket 2 Wrenches 4 3M Dual Lock Fasteners 1 User Manual 1 Smart Booster Optional and purchased independently Monitor Alarm Lamp LCD Display CJ _ Security lock Security lock o Wrench Transmitter III Installation and Programming of TPMS1209T08 T 1 Installation of Monitor 1 1 Insert the pedestal of acetabulto the backplane slot of the monitor 1 2 Choose a suitable location on dashboard to install the Monitor 1 3 The monitor power wire consists of 3 different colors of wires The Black wire should be connected to the ground Red wire to vehicle s continuous power supply Blue wire to ignition switch when switched to ON blue wire will have the power The monitor starts to work after it is powered At this time the monitor cannot receive any information as the transmitters are not installed The screen shows NSP which means there are No Sensors Programmed 9 2
4. range 40 C 125 C Storage temperature range 40 C 125 C Transmitter weight about 24 g VIII Frequently Asked Questions 25 1 Why do I need to check the tires periodically with the TPMS system installed Periodic check of the tire can keep the driver aware of the tires conditions and ensure driving safety 2 Pressure alarm frequently occurs The user can check if the standard pressure is suitable or not If the standard pressure is too high or too low re set the standard pressure as per instructions on page 7 of USER MANUAL 3 How long can the transmitter battery work The transmitter battery can last about 5 years under normal conditions 4 How to deal with the transmitter trouble alarm issued by monitor If one transmitter fails to work or the monitor cannot receive the signals for 20 minutes because of the RF interference the system will issue a transmitter trouble alarm Once there is no interference the system shall recover normal performance 5 Why the temperature sensed by the transmitter is quite different from the actual value The temperature sensed by the transmitter is the environment temperature not that inside the tire When vehicle runs the temperature around the transmitter will rise When there is high temperature alarm please check if the tire 1s under abnormal condition which causes the wheel rim becomes very hot and 26 lower its temperature in time 6 The monitor displays nothing or abnormal code
5. 5 TPMS1209T08 T USER MANUAL Suzhou Sate Auto Electronic Co Ltd www sate com cn Table of Contents I TPMS1209T08 T Full time Direct TPMS 2 II Parts of TPMS1209T08 T 2 II Installation and Programming of TPMS1209T08 T Monitor 3 1 Installation of Monitor 3 2 Programming of Monitor 4 2 1Programming of Transmitter D 5 2 2 Standard Pressure Programming 6 2 3 System Time Programming 8 2 4 Programming of Pressure Unit 10 2 5 Deletion of Transmitter D 11 IV Installation of TPMS1209T08 T Transmitter 12 1 Installation of Transmitter 12 2 Installation of Security Lock 14 V System Function of TPMS1209T08 T 15 1 Full time Monitoring 15 2 High Pressure Alarm 15 3 Low Pressure Level 1 Ala
6. 6 The warranty does not cover the product damage due to abrasion and corrosion 28 X Important Notes 1 The Warranty Card must be filled completely and its number shall be quoted whenever the user requires the service 2 Please inform Sate in case that the telephone number or address on the Warrant Card 1s changed 3 The warranty responsibility is subject to the conditions and limitations specified in the User Manual 4 TPMS1209T08 T monitor should be connected with the continuous power supply and installed by the professional S amp T is not responsible for the vehicle circuit damage or accident caused by wrong installation or improper use of the system 5 S amp T TPMS can perform full time monitoring function but cannot avoid all unexpected accidents 29
7. Programming of Monitor Through the monitor the user can program up to 38 transmitters D numbers and the standard pressure for each wheel Operation steps are as following 2 1 Programming of Transmitter ID When the monitor is powered for the first time the screen shows NSP which means there 1s no transmitter programmed into it If the user wants to program a new transmitter into the monitor the operation should be finished in programming mode At this time make sure the transmitter to be programmed has not been screwed onto the valve yet Screw on transmitters until the programming has been finished and the monitor returns to normal mode Each transmitter has 4 groups of ID for example when program the transmitter with ID of 001 001 001 158 to front right tire position the user only needs to input the last 3 digits 158 Monitor will record the rest 3 groups of ID automatically Operation steps are as following 1 After monitor is powered the screen will display NSP press P for 3 seconds to access the system programming mode the first interface is for ID programming as shown below 2 Press any of the four arrow keys to choose the tire position which needs to be programmed with a transmitter 3 Then press S for 3 seconds to start programming and the digit flashes 5 then press up or down arrow key to adjust the number 4 Once finish programming of the first digit press to start programming the
8. e 15 pressure 1s 25 higher than the standard Alarm mode the alarm lamp flashes high pressure warning icon tire position icon and the audible alarm turn on together Treatment press any key to stop the audible alarm The red alarm lamp remains on and the display reverts to the normal mode At this time user should properly adjust the tire pressure to the normal level The red alarm lamp goes off only when the tire pressure returns to the normal level 3 Low pressure level 1 alarm Display mode Function the system will issue low pressure level 1 alarm when the tire pressure 1s 12 5 lower than the standard Alarm mode the alarm lamp flashes low pressure level 1 alarm icon tire position icon and the audible alarm turn on together Treatment press any key to stop the audible alarm The red alarm lamp remains on and the display reverts to the normal mode At this time the user should adjust the tire pressure to normal level as soon as possible The red alarm lamp goes off only when the tire pressure returns to normal level 16 4 Low pressure level 2 alarm Display mode Function the system will issue low pressure level 2 alarm when the tire pressure 1s 25 lower than the standard Alarm mode the alarm lamp flashes low pressure level 2 alarm icon tire position icon and the audible alarm turn on together Treatment press any key to stop the audible alarm The red alarm lamp remains on and the display revert
9. emperature or pressure press S key for 3 seconds to start programming Take change the temperature unit as an example under the temperature unit interface press S 10 key for 3 seconds the temperature unit C starts flashing Press up or down arrow key to select the needed temperature unit After select the desired unit press S key for 3 seconds to save with the beep buzzes twice Pressure unit will stop flashing 2 5 Deletion of transmitter ID 1 When finish programming temperature and pressure unit press P to access the transmitter deletion interface Only the programmed and received transmitter will be shown and only the last 3 ID digits will be shown 2 Press any of the four arrow keys to locate the tire position to be deleted 3 Press S key for 3 seconds to delete with the screen flashes twice and beep buzzes twice to confirm the deletion Then it automatically switches to next transmitter location Note After programming press P key for 3 seconds to return to normal mode IV Installation of TPMS1209T08 T Transmitter Before install the transmitter make sure the transmitter has been programmed into the monitor and monitor is under normal mode If no transmitter 1s programmed or transmitter signal is not received after program the screen will display NSP When the transmitter is screwed onto the valve according to the programmed position the monitor can receive the signals and then disp
10. iver for 5 minutes When the receiver receives the match information the screen switches to the match interface If they match successfully screen will display the last 3 digits of ID trailer outline wheel position start flashing as shown below 3 The receiver can save the latest 5 trailers information At this time press up or down key to select the correct trailer ID number After the desired trailer ID appears press left or right arrow key to select TRAILER ON or TRAILER OFF After select TRAILER ON press S key for 3 seconds with beep buzzes twice and digits flash twice to confirm hook up success then return to the normal mode The receiver displays trailer outline wheel position and the icon TRAILER ON As shown below If don t want to hook up any trailer user can choose TRAILER OFF Note If the desired trailer number is not shown in the list of latest 5 trailer numbers on receiver please disconnect and then reconnect booster s power The process to drop a trailer is as follows 1 When the smart booster is powered off it will not send match information signal If the receiver can not receive the match information within 90 seconds the system will access the trailer deleting interface automatically and screen will display The trailer outline 21 and trailer wheel positions will flash 2 If the user wants to delete the trailer press to s
11. lay the transmitter location icon pressure temperature information on the screen When all programmed transmitters are received by the monitor and the pressure or temperature are in proper state the screen displays ON 1 Installation o Transmitter 1 Remove the current tire valve cap 2 Inflate the tire to the standard pressure recommended by the manufacturer or pressure needed by the user Note Each transmitter has a lock to prevent it becomes loose or falls off Install the lock or not will not influence the functions of the Transmitter If the user chooses to use the lock please refer to the below part of lock installation Security Lock and Transmitter should be installed at the same time 3 Screw the transmitter onto the tire valve 4 Check the connection of Transmitter and valve with the soap solution to confirm whether the transmitter is properly installed check if there is air leakage caused by the installation or the seal of the Transmitter 5 Once screwed onto the tire transmitter can sense the pressure inside the tire and transmit the data to the monitor and the information will appear on the screen within about 6 minutes Note 1 Please set the standards pressure of each tire on monitor before install the transmitter The standard pressure for 13 each tire location has been preset tol00PSI in factory 2 If one of your transmitters 1s broken or lost user only needs to replace this one
12. n 2 8 psi within 12 seconds Alarm mode the alarm lamp flashes and the audible alarm turns on the tire position icon flashes Treatment press any key to stop the audible alarm and the system reverts to normal mode Then slow down and check the correspondent tire 8 Transmitter Trouble Alarm Display mode Function If one transmitter fails to work or the monitor cannot receive the data because of the RF interference for 20 minutes the system will issue a transmitter trouble alarm Alarm mode the audible alarm turns on the red alarm lamp flashes and transmitter trouble alarm icon appears Treatment press any key to stop the audible alarm Then the system reverts to the normal mode Note The red alarm lamp goes off automatically when the communication between the transmitter and monitor returns to normal state VI TPMS1209T08 T Auxiliary Functions in Normal Mode 1 Hoop up and drop a trailer Receiver can receive and display the tire pressure and temperature information of the trailer wheels through the smart booster installed on the trailer The process to hook up a trailer is as follows 1 Make sure that receiver and smart booster have been installed and programmed receiver is in the normal mode As for the installation and programming of smart booster please refer to user manual of the smart booster and hand tool 2 Once powered on the smart booster will transmit the match information to the rece
13. ows 1 When finish programming the standard pressure press P to access interface for inquiry and programming of time date the first interface displays the year 1 07 stands for the year 2007 2 Press key to access the second interface 211 stands for November as shown below 3 Press the key to access the third interface 312 stands for 12th day as shown below 4 Press the key to access the fourth interface 416 stands for 16 O clock as shown below 5 Press the key to access the fifth interface 533 stands for 33 mins As shown below Under any interface of system time inquiry press S for 3 seconds to start programming For example change the year to 09 under the year interface press S for 3 seconds the second digit flashes press up or down arrow key to adjust the value Then press key the third number flashes then press the up or down arrow key to adjust the value to 9 At last press S for 3 seconds to save the change with screen flashes twice and beep buzzes twice Then it automatically switches to next interface for programming 2 4 Programming of Temperature and Pressure Unit 1 After program the system time press P to access the pressure unit programming interface Under the pressure unit programming interface press S key for 3 seconds to adjust the programming Press or key to select the desired pressure unit 2 Under any interface displaying t
14. rm 16 4 Low Pressure Level 2 Alarm 16 5 Low Pressure Level 3 Alarm 17 6 High Temperature Alarm 18 7 Quick Leak Alarm 18 8 Transmitter Trouble Alarm 19 VI TPMS1209T08 T Auxiliary Functions in Normal Mode 20 Alarm Record Inquitry 20 VII Specifications 22 VIII Frequently Asked Questions 24 IX Warranty Term 28 X Important Notes 29 I TPMS1209T08 T FULL TIME DIRECT TPMS TPMS1209T08 T is direct tire pressure monitoring system for trucks which includes 1 monitor 1 smart booster optional and 2 to 38 transmitters and it can support monitoring of up to 38 tires The transmitter can be screwed onto the tire valve and then senses the pressure and temperature all the time and send data to monitor by RF The monitor can receive and deal with the data then display the
15. s to the normal mode The user should slow down the vehicle and drive to a service shop to inflate the tire The red alarm lamp goes off only when the tire pressure returns to normal level 5 Low pressure level 3 alarm Display mode Function the system will issue low pressure level 3 alarm when the tire pressure 1s 50 lower than the standard Alarm mode the alarm lamp flashes low pressure level 3 alarm icon tire position icon and the audible alarm turn on together Treatment press any key to stop the audible alarm The red alarm lamp remains on and the display reverts to the normal mode The user should slow down the vehicle and replace the tire with a spare tire The red alarm lamp goes off only when the tire pressure returns to normal level 6 High Temperature Alarm Display Mode Function When the temperature around the transmitter equals or exceeds 90 C the system will issue the high temperature alarm Alarm Mode the alarm lamp and temperature value flashes tire position icon and the audible alarm turn on together Treatment press any key to stop the audible alarm The red alarm lamp remains on and the display reverts to the normal mode The driver should slow down and properly cool down the tire The red alarm lamp goes off automatically when the temperature returns to normal level 7 Quick Leak Alarm Display mode Function the system will issue a quick leak alarm when the pressure drops more tha
16. second digit which flashes Press up or down arrow key to adjust the number 5 Press again to program the third digit which flashes Press up or down arrow key to adjust the value 6 When finish programming these 3 digits press S for 3 seconds to save with the screen flashes twice beep buzzes twice Then it will automatically switch to next tire position 7 Repeat the above operations to program ID of other transmitters 2 2 Standard Pressure Programming For example set the standard pressure of front right tire to 105 psi 1 When finish programming ID press P to access the standard pressure programming mode 2 Then press any of the four arrow keys to choose the desired tire position 3 Then press S for 3 seconds to set the first digit which flashes Press up or down arrow key to adjust the value to 1 4 Once finished programming the first number press to program the second digit which flashes and then press up or down arrow key to adjust the value to 0 5 Once finished programming the second number press to 7 program the third digit which flashes and then press up or down arrow key to adjust the value to 5 Then press S for 3 seconds to save the setting Note The default standard pressure is set to 100 psi in factory 2 3 System Time Programming Function The system clock was preset in the factory It is the base of the alarm record user can check the current date and time as foll
17. witch between TRAILER ON and TRAILER OFF If user chooses TRAILER OFF press S key for 3 seconds to save with beep buzzes twice figures flash twice and the system will return to normal mode automatically as shown below If user does not want to delete the trailer information choose TRAILER ON 2 Alarm Record Inquiry 1 Under normal mode or pressure inquiry interface press P and S at the same time for 3 seconds to access the alarm record inquiry interface The screen with 0 is the most recent alarm record as shown below 2 Under alarm record inquiry interface Press key to check through the record If there is no operation within 3 seconds it will automatically display the record data pressure temperature and time 22 in turn each data displays 3 seconds Pressure Temperature Time year Time month 23 Time date Time hour Time minute Then it will display the next alarm record in the same way as above 4 Press P and S at the same time to exit VH Specifications Monitor Modulation Type FSK Mid frequency 434 1 MHz Receiving Sensitivity 105 dBm Input Voltage 12V 24V Current lt 60mA Operating Temperature 30 C 70 C Storage Temperature 30 C 75 C Transmitter Modulation Type FSK Mid frequency 434 1 MHz Transmitting Power 0 dBm Input Voltage 3 6V Battery Static Current lt 0 7uA Operating temperature
Download Pdf Manuals
Related Search