SAEY 92 (TOP) WOOD/COAL
Contents
1. 5 877 0000 130 877 0000 600 576 0027 760 877 0000 660 77 0000 50 2 8 036 420 8 0042 920 aa 877 0000 040 877 0000 240 28 877 0000 110 00 87 0000 290 28 878 0088 020 a77 0000 120 00 FOJIR 00 877 0000 300 28 877 0000 520 28 11 19 Faults a The fire is not burning well Wood too moist e Check max residual moisture 20 Wrong fuel e Use only the fuel allowed for the appliance Chimney draught too weak Check the air tightness of the outlet Minimal pressure 10Pa at the Light a kindling fire in the chimney heating gas connector pipe Close any open doors of other appliances connected to the chimney Close the cleaning hatches of the chimney If necessary clean the connector pipe Not enough combustion air e Check the ventilation installation of the residence or cooker hood and open a window if necessary Glass soon gets dirty Wood too moist e Check max residual moisture 20 Wrong fuel Fuel not small enough max circumference is 50 cm Use only the fuel allowed for the appliance Too much wood has been added not add than 2 to pieces Not enough combustion air e Check the ventilation installation of cain the residence or cooker hood and open a window if necessary A lacquer odour is emitted Curing of the primer used Rapid heating of the heating and smoke develops appliance will result in an odour being g2. Sustained combustion is only achieved through regular top ups which means only when the wood has almost been burnt up and the degassing process completed high flames are reduced to small low flames and wood is converted into glowing embers can the emission of heat be slowed down by closing the air slider above the glass door See image 14 4 Stoking up the fire with wood Ash removal Take note de not poke the fire when the appliance is in operation Wood combustion produces little ash Because of this the remains of the embers continue to smoulder in the glowing ash 15 Removal of the ashes The ashes from the stove have to be removed daily 1 till 2 times Poking happens with a shaking bar that is located on the back with a closed ash door From time to time the slag rests has also to be removed This can happen with a pull grid The pull grid is located behind the ash door and the handle is pulled away In this purpose you get an opening and you can easily scrape the ash rests and slag with a poke The ash pan may be maximally filled with ash to the upper edge No ash cone may be formed otherwise cooling of the combustion chamber becomes impossible and the cast iron parts would begin to melt The ash door should always be closed when the stove is in operation If this is not done the stove overheats and is damaged 16 Maintenance The smoke discharge duct between the checking plate and the rear wall must be cleaned
3. Open the door with the glass panel and put crumpled newspapers on the fire grating with a handful of splintered wood thin wood on top of it Alternative 4 5 firelighters Pour on that a small amount fuel After the stove has been lit the door with the glass panel must be firmly closed The door of the ash pan must be opened slightly so that the condensation vapours that are released will not be deposited on the cold door with the glass panel Monitor the combustion process and close the door of the ash pan after about 10 minutes IMPORTANT The door of the ash pan and the door with the glass panel should now not be opened again except for the purpose of topping up 10 Filling with coals You may start to fill the stove when the lighting fuel is totally burnt up and if the base is still glowing sufficiently The filling funnel is filled as it suits you but it has to be at least half full The stove may only be filled till the mark sign The above gas slots in the filling funnel must stay free so that the gases carbonized at a low temperature could escape When max filled the stove can work 14 till 16 hours When max filled with lower thermostat position till 24 hours To stoke air drawer fix closed thermostat position 2 8 as you desire IMPORTANT It is recommended to put the thermostat a lower position after half an hour For this purpose are you sure that the burning 1 carried out correctly The
4. after every heating season at least 1 x a year By removing the control damper you will be able to reach the smoke discharge duct This makes it easy to remove the fly ash from the discharge duct as well as the connector The control damper must be put back correctly afterwards It is recommended that after the feating season during the summer months the flue pipe between the stove and chimney should be removed or sealed in order to prevent condensation and or corrosion in the stove This improves the durability of your stove Before starting again to heat with your stove after a period of not using it is recommended to decrease the tension of the screws on the glass by using a screwdriver this case you will raise the lifespan of the glass and avoid possible cracks 17 Instructions With the luxury appliance you may put just after 1 month in use on the polished filling funnel lid and the carrier water kettle pans etc No water may be spilled on the hot plates to prevent cracks from forming 18 Spare parts SAEY 92 KOLEN 478 0292 SAEY 92 CHARBON 677 0000 210 877 0000 080 878 0045 200 677 0000 030 8 003 380 B7 7 0000 170 B77 0000 550 678 006 25 878 0000 340 00 878 0000 430 18 B78 0000 330 00 78 3701 18 877 0002140 877 0000 150 877 0000140 00 878 0000 440 18 877 0000 220 001 873 0000 450 18 877 0000 070 00 878
5. when the stove is not in operation 4 Installation of the stove It is only when the appliance was connected by an authorised installer that you can be certain that the installation and fire protection instructions were observed The most important connection component is the chimney Make an appointment with a recognised chimneysweeper so that the specific regulations applicable in the country of use in this regard are also complied with Also pay attention to the following The stove is suitable for a chimney with several shafts For this purpose the stove must be used with closed doors The inflow of air must be sufficient in whatever space the appliance has been installed Tightly closed doors and windows may cause problems in this regard Preferably place your stove near the chimney hearth A heat resistant fireproof base bottom plate must be placed underneath the stove These bases made of cast iron steel sheeting are available commercially In any case ensure that the base is fireproof Flammable objects such as doors furniture woodwork etc must be at a distance of at least 60 cm Thanks to the protective plate at the back of the stove the appliance may be placed up to 30 cm from the wall 5 Connection of the stove to the chimney A strong chimney draught makes it possible to connect the stove directly to the chimney with outlet at the back The diameter of the smoke duct must correspond with that of t
6. 0000 300 16 877 0000 060 00 8678 0034 7409 00 878 0000 390 18 4 00 18 877 0000 010 00 877 0000 020 00 878 0000 350 18 878 0000 350 18 8770000090 877000060 877 877 0000 130 B77 0000 600 727 750 878 0088 040 877 0000 590 2 873 0034 420 878 0034 7420 00 376 0034 500 878 0027 3 20 877 0000 040 00 78 0000 110 00 6785 0000 3850 878 0000 410 18 0000 120 1001 877 0000 220 00 878 0000 420 18 27 8 0000 450 18 10 SAEY 92 KOLEN 478 0392 SAEY 92 CHARBON 77 1000 210 BY 0000 00 1 B78 0043 200 877 0000 630 878 0039 380 571 0000 170 877 0000 650 5 877 0000 540 878 0098 250 78 003 760 878 0043 740 001 878 0043 741 28 478 0043 750 78 0043 680 00 Sees 478 0002 930 28 JO 877 0000 150 877 0000 180 ar77 0000 070 00 877 0000 280 28 6 2 28 877 0000 140 00 877 0000 310 26 877 0000 220 001 877 0000 200 877 0000 320 28 877 0000 190 8 0042920 Da 878 0039 410 477 0000 040 00 EErEE 877 0000 270 28 i 877 1000 020 77 0000 010 00 S 877 0000 240 28 877000009 V 877 0000620 77 0000 230128 878 0027 760 878 0027 770 77 0000 100
7. SAEY Home amp Garden Documentation addressed Industrielaan 4 to the user and installer B 8501 Kortrijk Heule www saeyheating com Installation and Operation Manual SAEY 92 TOP WOOD COAL 478 0292 XX Saey 92 coal 478 0392 XX Saey 92 TOP coal Contents N gt 59 10 11 12 13 14 14 1 REBUILD 14 2 REFILL 14 3 SERVICE GENERAL INFORMATION ccccsssseccccnnseecccnaseecccnaseesecnaseesecassesennaseesens TECHNICAL CHARACTERISTICS DIMENSIONS OF THE 6 IMPORTANT INSTALLATION OF THE STOVE cssscccssseccnnsecccnsseccnssecennseseesssecnesseeeas CONNECTION OF THE STOVE TO THE CHIMNEY SUITABLE FUEL BEFORE FIRST USE WARNING PLAYING CHILDREN STOKING UP OF THE FIRE FILLING WITH CORES STOKING UP THE FIRE WITH BROWN COAL STOKING UP THE FIRE WITH BRECHCOKEG 1111111 REFILE FUELS 2 S
8. TOKING UP THE FIRE WITH WOOD 144 ASHREMOVA 15 REMOVAL OF THE ASHES 16 MAINTENANCE 17 INSTRUCTIONS cccccccccccccccccccccccccccccccccccccccccccecccecccccccceccescececeeseesess 18 SPARE PARTS Es Seater eT eRe mere ere eee 20 GUARANTEE oa oa A A QOQ 10 12 14 1 General information Dear user When you purchased this SAEY 92 you chose a high class cast iron combustion and heating appliance Our warmest congratulations We devoted a lot of attention to the technology but also to the materials used the processing and the compactness of the appliance This enables us to guarantee problem free operation If you wish to achieve maximal performance in terms of ecological and economical considerations you should comply with this installation and operation manual and carry out its instructions If the stove is damaged due to non compliance with the installation and operation manual the guarantee will no longer be valid the stove is built in the applicable laws and local regulations regarding fire prevention and archite
9. ctor The chimney and the stove must be cleaned once a year by a recognized chimney sweeper 6 Suitable fuel The SAEY 92 stove makes use of the following fuels Anthracite grain structure 20 30 wood logs with sticky bark e g cleaved logs with a length of 33 cm The wood should be stored for about 2 years and should have a maximum residual humidity level of 20 Wet wood does not burn well and produces smoke resulting in condensation and a tar discharge which makes the stove dirty Take care DO NOT burn waste matter When burning wood a rebuilding of the stove is necessary and some further regulations and air supplies are different to handle 7 Before first use When used for the first time the stove must be dried out first For this purpose use a little fuel to keep the fire burning for one hour Thermostat on position Monitor the protection process carefully In this regard carefully wipe off any condensation drops before the residue gets a chance to burn into the enamel e g the lacquer 8 Warning Playing children A stove gets hot especially the covering plate the casing and the glass pane Install your stove in a safe place in order to prevent children from touching it Even if all the safety regulations are observed there is still a risk of accidents occurring KEEP SMALL CHILDREN AT A SAFE DISTANCE 9 Stoking up the fire When the stove is lit thermostat on position 8
10. cture should be complied with Are you looking for further information or technical data Installation problems Contact your distributor first Please keep safe place Subject to amendment Sketches are not contractually binding 2 Technical characteristics TYPE Maximum heating capacity Performance class Dimensions of the stove Height stand type TOP type Width Width stand type TOP type Rear connection Distance middle connect pipe floor Stand type TOP type Outside of the connector pipe Dimensions glass HxWxThickness mm 461x265x4 Small filler door opening mm 18 5x 17 Max length for wood mm Type anthracite mm 20 30 Weight op the stove 5 92 kg 5 92 kg 3 Important WARNING The user of a stove must read the manual attentively before using the appliance for the first time If your stove has been installed in the living room you must ensure a sufficient supply of fresh air in any case The appliance should only be used with closed doors When the doors remain open once the stove is functioning the thermostat function is disabled the inflow into the stove is no longer being controlled The danger then arises that the stove will become too hot so that slag formation takes place and the parts exposed to the flames are damaged This kind of damage is not covered by the guarantee Shut the stove doors and turn off the thermostat even
11. he connector 150 mm When the draught of the chimney is insufficient under 0 08 mbar 0 8 mm WS the stove must be connected with a perpendicularly smoke duct of 1 till 1 5 m length with the chimney outlet above The smoke duct must be sealed at all connection points Attention is specifically drawn to the danger of escaping fumes False air results in a weaker chimney draught If the chimney draught is too strong the installation of a draught regulator is recommended Take note of the following precautionary measures before the smoke duct is installed The diameter of the smoke duct may not be reduced the smoke duct may not be made smaller and it may not be positioned horizontally but should rise towards the chimney at a slight angle The stovepipe must fit into the chimney opening to make the discharge of fumes possible Make provision for a double lining in this regard Chimney connections of different stoves may not be so positioned opposite one other i e at the same height This may obstruct the discharge of exhaust fumes The minimum distance between two outlets for fumes should be at least 30 cm Do not connect too many stoves to one chimney too many connections hamper the upward draught Ask you chimney sweeper for advice The chimney may not conduct any false air Ensure that the chimney control valves as well as the cleaning openings in the cellar are closed The smoke duct must be securely attached to the conne
12. ignition of the thermostat depends also on other factors the local circumstances the condition of the building and the chimney After a bit experimentation you will regulate easily and definitely your stove 11 Stoking up the fire with brown coal The amounts usable fuel long briquettes 6 7 and little briquettes is defined by the desired warmth Only when there is much warmth necessary the stove has to be filled fully The smallest position 1 2 is the glow position For heating in the night when there is only a small need to warmth the 3 4 long briquettes are enough or 2 spades briquettes on the burning grid without poking in the ashes Put the thermostat on minimal air supply 1 2 12 Stoking up the fire with brech cokes When the burning is weak the brechcokes needs a bigger amount of burning air It is not possible to make the stove work with a thermostat in the smallest position what the case is with other fuels Above all the thermostat could only be put gradually on a smaller position 13 Refill with fuels Coal with every refilling turn you have to use a shaking grid Before opening the filling funnel lid the thermostat has to be put on position 8 open So that the outlet gases that are located in the filling funnel or in the burning room not come on the place where the stove is located Wood not poke see 14 4 14 1 Stoking up the fire with wood Rebuild When you want your stove work
13. iven off see 3 1 This will dissipate after a while Condensation High temperature difference Open the door slightly during the heating phase Do not leave the appliance unattended during this phase Inconvenience caused by Chimney draught too weak Check the air tightness of the outlet smoke Minimal pressure 10Pa on the Light a kindling fire in the chimney outlet connector pipe Close any open doors of other appliances connected to the chimney Close the cleaning hatches of the chimney If necessary clean the connector pipe Fuel has not been burnt up In principle fuel should be topped completely up only when no more orange flames are visible in the stove Gradual capacity regulator Service grip thermostat 12 Ash pan Base position open outside Base position open outside Mark sign in filling funnel lid Max stacking height of logs max filling height coal Opening the filling funnel lid take out the filling funnel Take out the cleaning panel 13 20 Guarantee The manufacturer guarantees a impeccable quality and processing of the raw materials according to the stated requirements b assembled by an expert The guarantees a en b provide for free repairs to the appliance more specifically to parts declared unfit for use Such parts are only replaced free of charge when it can be proven that there are flaws in the raw materials or in the workmanship No further claims may be made The man
14. s with wood then there is a small rebuild necessary Following steps need to be done Remove the filling funnel after you opened the lid e Place the wood grid you can buy optionally instead of the coal grid e The secundairy air drawer between the 2 front doors must be open must be closed while using coals e With the 2 air drawers you can find above the fire door you can fix the air supply Release the air drawer button by turning 14 of a turn left should be closed while using coals 14 2 Stoking up the fire with wood Refill stoke thermostat position 1 2 base position wood air drawer open max The logs should be inserted through the right hand filler door or the door with the glass panel and placed on the still sufficiently glowing base in no more than 2 layers Do not overfill 14 3 Stoking up the fire with wood Service The burning of wood is accompanied by high flames and heavy smoke production Wood must be burnt up rapidly and with a constant oxygen supply The combustion process may not be slowed down under any circumstances Avoid an excessive amount of fuel in any case otherwise the energy surge become too great and too much heat will be lost Negative consequences could be smouldering fire condensation and tar discharge excessive production of soot inconvenience caused by smoke emission of harmful substances danger of asphyxiation WOOD PROVIDES INTENSE COMBUSTION OF SHORT DURATION
15. ufacturer does not guarantee Parts that are subject to wear and tear and damage to and defects in the appliances or their parts caused by Chemical or physical influences from outside with regard to transport storage incorrect installation and use of appliance e g cooling down with water overheating Use of inferior fuels incorrect operation The manufacturer is not responsible for direct or indirect damage caused by the appliance No claim can be laid to a full or partial exchange unless the manufacturer is unable to fix the flaw or damage within a certain time span Your Saey Flandria device is guaranteed for two years against any manufacturing defect from the date of purchase provided that it is used according to the user s manual till slip or bill indicating the date substitutes for the guarantee The scope of this guarantee is limited to the repair or replacement of parts that are discovered to be faulty during the course of normal use This guarantee does not apply to malfunctions due to poor installation incorrect use modification of the device dismantling of the device wear and tear or lack or maintenance Claims against guarantee must always be made at your point of sales 14
Download Pdf Manuals
Related Search