HDBaseT™ Signal Extender Installation Manual ®
Contents
1. HDBT R1 HDBaseT Signal Receiver e 6 24VDC Tx Rx RS 232 rf 4 Status Power 1 IR Out IR Out RS 232 24vDC E C E HDBT R1 Features The HDBT R1 is the signal receiver unit that connects to your display equipment It receives signals from the HDBT S1 signal sender unit connected to your source equipment 1 i D 9 HDBT IN This connects to the HDBT OUT port of the HDBT S1 using a single CAT5e or CAT6 TP twisted pair cable LINK LED Twisted Pair Link status indicator This green LED will stay on when HDBT con nection is successful ACTIVITY LED When connected with HDMI devices supporting HDCP and operating nor mally this green LED will stay on constantly If devices do not support HDCP this green LED will blink HDMI OUT Connect to the display via an HDMI cable IR IN Connect to an external IR receiver IR OUT Connect to an external IR transmitter RS 232 Connect to an RS 232 device or controller The HDBT R1 will pass the RS 232 commands to and receive from the RS 232 port on the HDBT S1 STATUS LED Status indicator of this device When the HDBT R1 is operating correctly this green LED will blink every two seconds POWER LED When the power to the unit is on this green LED will stay on 10 24 VDC Connect with the supplied external power supply Installing the HDBT SR1 System Before powering up your HDBT SR1 system connect all CATSe CAT6 and HDMI signal cable2. is the signal sender unit that connects to your source equipment It sends signals to the HDBT R1 signal receiver unit connected to your display equipment 1 HDBT OUT This connects to the HDBT IN port of the HDBT R1 using a single CAT5e or CAT6 TP twisted pair cable 2 LINK LED Twisted Pair Link status indicator This green LED will stay on when HDBT con nection is successful 3 ACTIVITY LED When connected with HDMI devices supporting HDCP and operating nor mally this green LED will stay on constantly If devices do not support HDCP this green LED will blink HDMI IN Connect to the source via an HDMI cable IR IN Connect to an external IR receiver IR OUT Connect to an external IR transmitter RS 232 Connect to an RS 232 device or controller The HDBT S1 will pass the RS 232 commands to and receive from the RS 232 port on the HDBT R1 8 STATUS LED Status indicator of this device When the HDBT S1 is operating correctly this green LED will blink every two seconds 9 POWER LED When the power to the unit is on this green LED will stay on YO nD 10 24 VDC Connect with the supplied external power supply HDBT R1 Signal Receiver Extends uncompressed HDMI signals up to 4K Supports HDCP and 3D pass through Extends IR and RS 232 Signals wwwaaudiocontrol com HDBT In HDMI Out IRIn Link Activity Link Activity O g HDMI Out AudioControl Making Good Sound Great
3. that sounds like a big loophole but here is all we mean by it Unwarranted abuse is A physical damage don t use the HDBT SR1 to level your dining room table B improper connections such as high voltages applied to the 24 VDC jack C sadistic things This is the best product we know how to build but if you strap it to the front bumper of your Unimog something might break Assuming you conform to 1 through 5 and it really isn t all that hard to do we get the option of fixing your old unit or replacing it with a new one Legalese Section This is the only warranty given by AudioControl This warranty gives you specific legal rights and you may also have rights that vary from state to state Promises of how well the HDBT SR1 will work are not implied by this warranty Other than what we ve said we ll do in this warranty we have no obligation express or implied We make no warranty of merchantability or fitness for any particular purpose Also neither we nor anyone else who has been involved in the development or manufacture of the unit will have any liability of any incidental consequential special or punitive damages including but not limited to any lost profits or damage to other parts of your system by hooking up to the unit whether the claim is one for breach of warranty negligence of other tort or any other kind of claim Some states do not allow limitations of consequential damages Failure to register your produ
4. 61 e www audiocontrol com
5. HDBT SR1 HDBaseT Signal Extender Installation Manual Congratulations You are installing the AudioControl HDBT SR1 a unique signal extension sys tem that uses HDBaseT technology and allows the user to extend HDMI video and audio signals up to 210 feet 70 meters over a single standard CAT5e CAT 6 cable Many system designs require the source equipment to be installed in one location or rack with the display device and or projector installed in another location The HDBT SR1 is an ideal connection system for these types of installations While you are probably chomping at the bit to get started on this installa tion we encourage you to take a few minutes to sit back with a beverage of your choice and review this manual It will probably answer a lot of ques tions you may have and save you some phone calls AudioContror Making Good Sound Great Important Safety Instructions BO Gre eS a 10 11 12 13 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with a dry cloth Do not block any ventilation openings Install in accordance with the manu facturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Use only the supplied power supply adapter Protect the power cord from being walked on or p
6. ct negates any service claims The warranty included with the unit shall supersede this plain text version if there is any inconsistency between the two HDBT SR1 Specifications All specifications subject to change without notice rather like the Pacific Northwest weather and versions of HDMI Inputs HDMI IR and RS 232 Outputs HDMI RJ 45 RS 232 and IR Audio Signal Protocol Digital through HDMI Output Video Protocol HDMI 1 4 Video Resolution 800 x 600 1920 x 1200 4K x 2K HDCP Support 1 4 Maximum Distance use CAT5e and CAT6 cabling 70 meters Transmission Protocol HDBaseT Gain 0 db to 10 dB 100 MHz Signaling Rate 10 2 Gbps Signal To Noise gt 70 dB 100 MHz THD lt 005 1 Khz Dimensions WxDxH 5 24 x 3 33 x 0 95 133 x 84 5 x 24 2 mm Weight sender and receiver 1 3 Ibs Power transformer 100 240 VAC IN 24 VDC 500 mA OUT 2014 AudioControl a division of AudioControl Inc All rights reserved AudioControl Making Good Sound Great HDBT S1 HDBT R1 and HDBT SR1 are trademarks of AudioCon trol Inc HDMI and High Definition Multimedia Interface are trademarks of HDMI Licensing LLC HDBaseT is a trademark of the HDBaseT Alliance This manual was conceived written and created during a uniquely warm and sunny period in the Pacific Northwest Music was cranking coffee was hot and the kids were sleeping AudioContror Making Good Sound Great 22410 70 Ave West Mountlake Terrace WA 98043 USA Phone 425 775 84
7. e HDBT SR1 MUST be a straight through cable and meet the following color scheme Note The cable connectors MUST be metal and the shielded layer of cable MUST be con nected to the connector s metal shell for better transmission Pin Cable color_ Pi green e foe b jo 8 ee blue white brown Tst Group and Grou 3rd Grou Ath Group Troubleshooting and Maintenance No video at display device 1 Check the Power and Status LEDs at both ends yes it had to be said 2 Check the LINK LED at both HDBT S1 and HDBT R1 for solid HDBT link If the LEDs aren t solid at either device replace the CAT5e CAT6 cable with a known good cable 3 Check the ACTIVITY LED at both HDBT S1 and HDBT R1 for HDMI link If the LEDs aren t solid at either device replace the HDMI cables one at a time to find the transgressor 4 Check the display device s settings and capabilities While the HDBT S1 HDBT R1 will pass through 4K UHD the display may not be able to display 4K UHD Ghost images This may be caused by incompatible settings between the source device and the display device or a cable which has been damaged or is of poor quality 1 Check that the source and display devices settings match 2 Check the HDBT S1 HDBT R1 LEDs as above to detect an intermittent HDBT or HDMI link Static in signal Static or snow could be caused by grounding but also may have to do with bandwidth limita tions of the HDMI interco
8. inched particularly at plugs convenience receptacles and the point where they exit from the apparatus Use only attachments accessories specified by AudioControl Disconnect mains power when the apparatus is left unused for a long time DO NOT open the outer case of the apparatus there are no user serviceable parts inside and this will void your warranty Key Features of the HDBT SR1 System Extends High Speed HDMI signals up to 70 meters over a single CAT5e CAT 6 cable Utilizes HDBaseT technology HDTV and 4K UHD Compatible HDMI 1 4 and HDCP compliant Supports CEC High Bandwidth of 10 2 Gps Delivers high resolution images 1080p 60Hz 48 b pixels 3D 4Kx2K 30Hz Transmits EDID and Hot Plug Detect signals to display constantly via CAT5e or CAT6 cable Bi directional RS232 IR control LED indicators For best results The slightly soggy AudioControl network video experts recommend using CAT6 twisted shielded pair cables HDBT S1 Signal Sender AudioControl Making Good Sound Great HDBT S1 HDBaseT Signal Sender Extends uncompressed HDMI signals up to 4K Supports HDCP and 3D pass through Extends IR and RS 232 Signals wwwaaudiocontrol com ik Rx C E E HDBT Out HDMI In IR In IR Out RS 232 24VDC r r a e Link Activity Status Power ds Link Activity Status Power O O O O Ix Rx HDBT S1 HDBT Out HDMI In HDBT S1 Features The HDBT S1
9. nditional doesn t mean anything ominous The Federal Trade Commission tells all man ufacturers to use the term to indicate that certain conditions have to be met before they ll honor the warranty If you meet all of these conditions we will warrant all materials and workmanship on your AudioControl HDBT SR1 for five 5 years from the date you bought it and we will fix or replace it at our option during that time Here are the Conditional Conditions 1 You need to register your purchase of the HDBT SR1 with us by going to the AudioCon trol web site www audiocontrol com and then go to the warranty registration page and follow the directions Optionally go to www audiocontrolregistration com 2 You must keep your sales receipt for proof of purchase showing when and from whom the unit was purchased We re not the only ones who require this so it s a good habit to get into with any major purchase 3 The HDBT SR1 must have originally been purchased from an authorized AudioControl dealer You do not have to be the original owner but you do need a copy of the original sales slip 4 You cannot let anybody who isn t A the AudioControl factory or B somebody autho rized in writing by AudioControl to service the HDBT SR1 If anyone other than A or B messes with the HDBT SR1 that voids your warranty 5 The warranty is also void if the serial number is altered or removed or if the HDBT SR1 has been used improperly Now
10. nnect cables The bandwidth limitations are illustrated by sparkling or dropped pixels similar to grounding issues Changing out the HDMI interconnect cables to shorter High Speed with Ethernet cables preferably less than 1 2 a meter generally gets the bandwidth back up to stabilize the signal However attenuation of bandwidth may have to do with a pinched or otherwise compromised Cat5e or CAT6 cable If the HDMI intercon nect change out doesn t do the trick run a new Cat5e CAT6 cable along the floor to test the bandwidth if the picture is clear then you may need to examine the Cat5e CAT6 cable that was originally installed If none of that works check the grounding of the source device and the destination device use an adapter plug to float either AV component to see if the issue goes away If both source and destination devices are floating then gives us a call we love puzzles And now a word from the legal department CONDITIONAL FIVE YEAR WARRANTY People are confused by warranties Lots of fine print Months of waiting around Well fear no more AudioControl is here This warranty is designed to make you rave about AudioCon trol It s a warranty that looks out for our customers plus helps you resist the temptation to have your friend who is good with electronics try to repair your AudioControl product So go ahead read this warranty then register the information at www audiocontrolregistration com Co
11. s The system should be installed in a clean environment that has moderate temperature and humidity All of the power switches plugs sockets and power cords should be insulated HDBT SR1 System Connection Diagram AudioControl AudioControl ee Waking Good Sound Great Making Good Sound Groat m HDB HDBT R1 HDB HI gnal Receiver oo oe ik r CEE w r CEE HoBT out HDMi iin Rout S232 ZAVO kostin homou Rin Rout_ RS 232 ZAVoC L Unk Ay stax rover up Atty suna rover Automated Screen Source Device IR Receiver Projector IR Transmitter Connection Procedure 1 Connect your HDMI source unit i e Blue ray DVD or AV Receiver to the HDMI IN port of the HDBT S1 using an HDMI cable 2 Connect the HDBT OUT port of the HDBT S1 to the HDBT IN port of the HDBT R1 using a single CAT5e CAT6 cable 3 Connect your HDMI display such as an HDTV or projector to the HDMI OUT port of the HDBT R1 using an HDMI cable 4 Both HDBT S1 and HDBT R1 units have an IR IN port and an IR OUT port When connect ing an external IR receiver to one unit s IR IN connect your external IR transmitter to the other unit s IR OUT Do not connect it to the same unit s IR OUT Connect the RS 232 port of the HDBT S1 or HDBT R1 to an RS 232 controller 6 Connect each unit to the supplied 24 VDC 500 mA power adapter HDBT SR1 Twisted Pair Wiring The twisted pair wiring used by th
Download Pdf Manuals
Related Search