Olivon EQ Mount User Manual
Contents
1. Fasten the small locking screw back onto the shaft Olivon EQ Mount Manual Tube Rings Installation 1 Remove the tube rings from your telescope by loosening the locking screws 2 Place the tube rings onto the mounting rail of the mount Fasten the ring onto the mount using the two screw holes with a screwdriver Make sure the two locking screws are pointing in the same direction Control Cable Fine Control Installation 1 Fasten the flexible slow motions onto the blots on the mount The bolt has a flat side on which the slow motion screw can be attached Telescope Tube Installation 1 Open the tube rings and place the telescope tube inside with its front upwards 2 Hold the tube in place close the tube rings and fasten both locking screws to secure Finder Scope Red Dot Finder Installation 1 Remove the pair of nuts on the top side of your telescope near the eyepiece to expose the two bolts 2 Align the holes on the base plate of your finder scope red dot finder with the exposed bolt facing in the same direction as the main telescope 3 Fasten the nuts removed in step back to the exposed bolts and secure the finder scope red dot finder Eyepiece Installation 1 Remove the black dust cap on the focuser 2 Loosen the knurled screws 3 For Newtonian Telescopes Insert the eyepiece then tighten the knurled screws to secure your eyepiece For Refraction Telescopes Insert the diagonal prism into the focuser first t2. Verify again that the same target is centered on the Red Dot Finder window and your main telescope C Balancing the Telescope Please note this procedure is very important for the longevity and smooth working of your telescope We recommend balancing the telescope after you have completed its setup at your viewing location Steps to Balance Your Telescope Right Ascension 1 While holding onto the telescope loosen the RA axis thumbscrew 2 Check if the telescope is tilting to one side 3 Loosen the counterweight screw to move the counterweight along its shaft to a position where the telescope no longer tilts to one side 4 Tighten the RA axis thumbscrew Declination 1 While holding onto the telescope loosen the DEC axis thumbscrew 2 Check if the telescope is tilting to one side 3 Loosen the tube ring screws Do Not completely remove the screws continued next page Olivon EQ Mount Manual 4 Slide the telescope to the position that it no longer tilts then tighten the ring screws Now your telescope is balanced D Aligning Your Mount to the Celestial Pole This procedure must be done before observations otherwise you will not be able to accurately track celestial objects Steps to Aligning the Mount in the Northern Hemisphere 1 Level the tripod and telescope by adjusting the tripod legs 2 Set up you mount and position telescope assembly so the front of the telescope and the counterweight shaft is facing north 3 Settin
3. TELESCOPE Dust Cap Mask Remove before Viewing Dew Cap Sun Shade Objective Lens Telescope Main Tube Piggyback Bracket Finderscope Finderscope Bracket Finderscope Alignment Screws Focus Locking Screw Eyepiece Diagonal Focus Tube Focus Knob Olivon EO Mount Manual Dec Flexible Control Cable R A Flexible Control Cable Altitude Adjustable T Bolt Azimuth Lock Knob Counterweight Counterweight Locking Thumb Screw Counterweight Rod R A Axis Scale Dec Scale 10 Dec Lock Knob 11 Tube Ring Mounting Plate 12 Tube Rings TELESCOPE A Dust Cap Mask Remove before Viewing Dew Cap Sun Shade Objective Lens Telescope Main Tube Piggyback Bracket Finderscope Finderscope Bracket Finderscope Alignment Screws Eyepiece Diagonal Focus Tube Focus Knob a Accessory Tray b Tripod Leg Dec Flexible Control Cable Altitude Adjustable T Bolt Azimuth Lock Knob Counterweight Counterweight Locking Thumb screw Counterweight Rod RA Flexible Control Cable RA Axis Scale 9 10 R A Lock Knob Dec Scale Dec Lock Knob 12 Tube Rings a Accessory Tray b Tripod Leg Important Safety Note DO NOT observe the sun with your telescope serious and permanent damage to the observer s eve may result Olivon EQ Mount Manual Assembly Instructions A Tripod Setup 1 Tripod Assembly Insert the lo
4. g the Latitude In Daylight When you can t see the stars clearly Obtain your observing coordinates from the Internet or from a GPS device For example for a location N48 3 E10 53 set your latitude to 48 on the setting circle on the side of your telescope At Night 1 Position your telescope so it is facing north and pointing to the North Star or Polaris 2 Loosen the locking lever near the setting circle on the side of your telescope 3 With the help of the lever turn the polar elevation screw at the rear of the mount to the left of right until your required geographical latitude Now the polar height and latitude are set Tighten the locking lever 5 Loosen the DEC axis locking screw turn the setting circle to 90 tighten the DEC axis locking screw 6 Turn the mount so the telescope points to the Pole Star and locate the Pole Star Now your telescope is aligned Do not move the tripod from now on Only move the the telescope in its two axes Steps to Aligning the Mount in the Southern Hemisphere The Southern celestial pole lies in the southmost constellation of Octans and the brightest star is the Sigma Octans locate it by extending the longer axis of the Southern Cross towards Octans Follow the same steps as described in Steps to Aligning the Mount in the Northern Hemisphere using the Sigma Octans as your target E Searching for a Celestial Object Olivon EQ Mount Manual After you have followed the
5. ighten the knurled screws to secure the prism Then insert the eyepiece into the diagonal prism and secure it Telescope How To s A Aligning the Finder Scope to Main Telescope An accurately aligned finder scope assists you in locating celestial objects quickly We recommend performing the following procedure in daylight Olivon EQ Mount Manual l 2 Point your main telescope to a sharp object example a church steeple tree top or telephone pole about 1 mile away and accurately center the object on your telescope s field of view Now look through the finder scope Using the three side adjustment screws accurately center your target to the crosshairs in the finder scope Verify again that the same target is centered on both your finder scope and your main telescope B Aligning the Red Dot Finder An accurately aligned red dot helps locate your target celestial object quickly in your view We recommend performing the following procedure in daylight Remove the plastic strip on the battery Turn on the Red Dot Finder by turning the small screw on the side Adjust the brightness of the Red Dot by turning the same screw Point your main telescope to a sharp object example a church steeple tree top or telephone pole about 1 mile away and accurately center the object on your telescope s field of view Using the azimuth adjuster at the front end and the height adjuster at the rear end to point accurately at your target
6. instructions above for balancing and aligning your telescope we recommend doing a test observation on a brighter object such as the Moon Venus or Jupiter that you can see with your eyes to make sure the telescope has been properly set up F Locating an Object The following steps are to be done on a properly set up telescope If not please review the previous sections for instructions Locating an Object Visually This is the recommended and more accurate method on the EQ mounts 1 Loosen the RA axis so the telescope can be moved in an arc similar to how celestial objects move This is the tracking axis 2 Loosen the upper DEC axis This is the elevation axis 3 Now the telescope can move freely in both axis Decide on a celestial object and point the telescope to its approximate direction 4 With the help of your finder scope or red dot finder use the fine adjustments to accurately locate the object 5 This takes practice In time you will be able to navigate through the sky quickly Locating an Object Using Its Coordinates Please note that on the EQ mounts the coordinates can only represent approximate locations and this method is meant to help you when you are having trouble finding it 1 Make sure your mount has been polar aligned accurately 2 Calibrate your telescope s settings to a known star a Choose a easy to find star and locate it with your telescope using the visual method For example Alkaid in the Big Dippe
7. ng screw with hexagonal head with wing nuts into the upper ends of the tripod leg and through the corresponding hole in the accessory tray Secure with the wing nuts and washer Do this with all three tripod legs 2 Tripod Height Adjustment For all three tripod legs extend the tripod legs by loosening the locking screws on the tripod legs and pulling the lower leg sections outward then tighten the locking screws to secure the position of the lower leg sections Now spread the tripod legs and stand the tripod on even ground so you can adjust the height of each leg as required 3 Accessory Tray Installation Fasten the accessory tray to the center brace of the tripod using the provided screws Please do not ignore this step as the tray not only provides you with the convenience of holding small accessories but also adds stability to the tripod B EQ Mount Setup Mount Installation 1 Place the parallactic mount and insert the lower pick up flange into the corresponding slot on the tripod s connection plate 2 Hold the mount with one hand then insert the large thumb screw from underneath the tripod s connection plate and fasten Make sure the mount is secured Counterweight Installation 1 Insert the counterweight shaft into the thread socket on the mount 2 Remove the small locking screw at the end of the shaft 3 Slide the counterweight onto the shaft then tighten the screw on the counterweight to secure it in place 4
8. r is very easy to find b Get the coordinates of the star you chose from a star atlas c Set the DEC and RA settings according to the reference value Now your mount has been calibrated 3 4 Using the reference coordinates from a star atlas adjust the DEC and RA setting to locate your target objects Enjoy the Views Thank you for choosing Olivon Olivon EQ Mount Manual
Download Pdf Manuals
Related Search