firmware 2.0
Contents
1. REMOTE OF THE RECEIVER RX AAprt reset of the receiver RX to channel 0 default channel after switching on or resetting FFar switch RX to channel 1 AOpen switch RX to channel 2 FNear switch RX to channel 3 AClose switch RX to channel 4 REC REC command to all receivers on all REC all cameras channels 0 1 2 3 4 channels after which the controller TX go back to default channel 0 go back to main camera Receiver reset RXreset Ch O Fn key pressed CONTROLLING THE TRANSMITTER TX AFcs TX reset and set to default channel 0 Key 1 TX to channel 1 Key 2 TX to channel 2 Key 3 TXto channel 3 Key4 TX to channel 4 ChO TX reset CONTROLLER KEY FUNCTIONS LAYER 3 Zoom mode Sony JVC Canon camera Signal LED blue and red blue light signalizes sending of the signal and the red light turns on when the record is on and turns off when the recording is off a Function KEeY tt Fn 7 ZOOM VELE secte na FFar C Focus FAR ina A Open d Focus NEAR ososi iata aa aneaciiui A Close e Recording on off REC ZooM WIDE aaa F Near g Focus PUSI soarece nrna A Fcs h speed 1 1 i speed 2 2 j speed 3 3 k speed 4 4 Aperture PUSH A Aprt Fn key pressed AAprt Auto Aperture FFar Onscreen DATA AOpen Greed FNear Shutter On screen DATA REC all ca2. LANC CONTROLLER DigiPin 13 WL1 firmware 2 0 ALWAYS TURN CAMERA OFF IF CONNECT OR DISCONNECT THE CONTROLLER We would like to thank you for buying our Lanc controller WL1 DigiPin 13 j d o o is a young company which strives to expand the technological aids and gadgets to a wide range of people with stress on simplicity and functionality of our products This product WL1 Lanc controller is meant to be used with Blackmagic cameras The basic goal of its simplicity and functionality is to make the usage of the video camera easier There are two versions of the WL1 controller wireless and cable Both controllers are marked the same the difference is that the cable controller has a cable with a Jack 2 5 mm connector at the end which connects to the Lanc camera input and the wireless controller has no cable but a receiver with a cable with Jack 2 5mm connector which connects to the Lanc camera input Wireless Lanc controller WL1 TX User manual ALWAYS TURN CAMERA OFF IF CONNECT OR DISCONNECT THE CONTROLLER PLUGGING IN THE CAMERA Wireless Controller WL1 CONNECT OR DISCONNECT THE RECEIVER RX ONLY WHEN THE CAMERA IS TURNED OFF Receiver RX for this controller uses the energy from the Lanc connector on the camera itself and the transmitter TX uses two batteries AAA 1 5 V 2 x AAA 1 5 V as the energy source 1 Turn the camera off 2 Plug in Jack 2 5 mm receiver into the Lanc camera input Rece
3. function only for the Blackmagic Studio Camera Fn key pressed REMOTE OF THE RECEIVER RX AAprt reset of the receiver RX to channel 0 default channel after switching on or resetting REC all cameras channels 0 1 2 3 4 FFar switch RX to channel 1 AOpen switch RX to channel 2 FNear switch RX to channel 3 AClose switch RX to channel 4 REC REC command to all receivers on all channels after which the controller TX go back to default channel 0 go back to main camera Receiver reset RXreset Ch O Fn key pressed CONTROLLING THE TRANSMITTER TX AFcs TX reset and set to default channel 0 Key 1 TX to channel 1 Key 2 TX to channel 2 Key 3 TX to channel 3 Key 4 TX to channel 4 ChO TX reset CONTROLLER KEY FUNCTIONS LAYER 2 Sony JVC Canon camera Signal LED blue and red blue light signalizes sending of the signal and the red light turns on when the record is on and turns off when the recording is off a Function KEeY eee es Fn FOCUS I I an FFar c Aperture Open A Open d Aperture Close A Close e Recording on off REC FOCUS EAE Laici F Near g Automatic foCUS A Fcs h ZOOM TELE slow 1 i ZOOM WIDE slow 2 j ZOOM TELE fastest 3 k ZOOM WIDE fastest 4 Automatic Aperture A Aprt Fn key pressed
4. iver RX 1 3 Turn the camera on and wait until the camera system loads and until the red led diode on the receiver turns off around 2 seconds 4 Insert the one battery AAA 1 5V into the transmitter TX while paying attention to the battery polarity pole to pole and pole to pole then chose LAYER 1 2 3 or 4 by press and hold button 1 2 3 or 4 and while insert the second battery AAA 1 5V into the transmitter TX with paying attention to the battery polarity pole to pole and pole to pole Layers chose only first time or when you need other layer Transmitter TX 5 You may start using the wireless Lanc controller WL1 BE SURE TO TURN THE CAMERA OFF Before plugging out the receiver RX from the camera CONTROLLER KEY FUNCTIONS LAYER 1 Blackmagic Design camera Signal LED blue and red blue light signalizes sending of the signal and the red light turns on when the record is on and turns off when the recording is off a Function KEeY tt Fn DI FOCUS ia FFar c Aperture Open eee A Open d Aperture ClOSE A Close e Recording on off REC FOCUS MICA aiar F Near g Automatic foCUS A Fcs h ZOOM SHUTTLETELE 1 i ZOOM SHUTTLEWIDE 2 j FOCUS SHUTTLEFAR 3 k FOCUS SHUTTLENEAR 4 Automatic Aperture A Aprt Functions h i j k currently in
5. meras channels 0 1 2 3 4 E AClose White Balance RESET AFcs Auto Focus REC REC command AFcs Auto Focus Key 1 Rec search Key2 R h Key 3 Power Off A o iii Power Off Stand By Maintenance Wireless transmitter TX uses very little electricity It is best to take out the batteries after every usage Do not store in moist areas The controller can be upgraded programmatic and the instructions and versions of the programmes will be available on the web page www digipin13 hr The package includes 1 Wireless controller WL1 transmitter TX 2 Receiver RX HOT SHOE with cable with a male Jack 2 5mm connector at the end This product is patented and protected All rights reserved by the owner of the patent Designed manufactured and patented DigiPin 13 j d o o Hedvige Deker 53 31400 Djakovo CROATIA www digipin13 hr E mail digipin13 digipin13 hr Support support digipin13 hr
Download Pdf Manuals
Related Search