Home

PR-8201

1. PR 8201 This product manual contains important information about the safe installation and use of this projector Please read and follow these instructions carefully and keep this manual in a safe place for future reference PR LIGHTING LTD http www pr lighting com INDEX SAFE USAGE OF THE PROJECTOR INSTALLING THE PROJECTOR CONTROL SYSTEM AND POWER CONNECTIONS DMX TERMINATOR SETUP OPTIONS PROJECTOR CONFIGURATION TO SET THE DMX START ADDRESS OPERATION MENU DMX PROTOCOL INDICATION OF LED DISPLAY MAINTENANCE TROUBLESHOOTING TECHNICAL DATA 10 ELECTRICAL DIAGRAM 13 COMPONENT ORDER CODES 14 DAO B co Please note that as part of our ongoing commitment to continuous product development specifications are subject to change without notice Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement The publishers cannot be held responsible for the accuracy of the information herein or any consequence arising from them Every unit is tested completely and packed properly by the manufacturer Please make sure the packing and or the units are in good condition before installation and use Should there be any damage caused by transportation consult your dealer and do not use the unit Any damage caused by improper use will not be assumed by the manufacturer and or dealer ACCESSORIES These items are packed toge
2. connections are the same as above it is master slave mode connection To achieve master slave mode set the first fixture master the others salve slave is default As for power connections each projector has to be supplied separately by external power Use the power cord of each projector to connect the mains power directly paying attention to the voltage and frequency marked on the panel of the projector Use the power cord of the first projector s power in cable connect to the mains power directly then connect the first fixture s power out cable to the second fixture s power in cable and connect the rest fixtures in the same way Eventually all fixture connect finished When using voltage is 200V 220V 230V 240V the amount of projectors connected is not more than 15 When using voltage is 100V 120V the amount of projectors connected is not more than 8 Paying attention to the voltage and frequency marked on the panel of the projector 4 16 All of the connections are as the figure below TO MAINS POWER POWER OUT TO CONTROLLER POWER OUT DMX TERMINATOR In the Controller mode at the last fixture in the chain the DMX output has to be connected with a DMX terminator This prevents electrical noise from disturbing and corrupting the DMX control signals The DMX terminator is simply an XLR connector with a 120Q ohm resistor connected across pins 2 and 3 which is then plugged into the output socket on
3. frequency depends on the environment in which the fixture operates Soft cloth and typical glass cleaning products should be used for cleaning It is recommended to clean projector at least once every 20 days Do not use any organic solvent e g alcohol to clean housing of the apparatus TROUBLESHOOTING PROBLEM ACTION gt Power connection is not correct gt Power supply is damaged or abnormal Call a qualified personnel The projector doesn t switch on to fix it gt Connection of control board is not correct Call a qualified personnel to fix it The projector can be turned on but LEDs do gt Connection of LED board is not correct Call a qualified not emit light and are out of control personnel to fix it The lamp comes on but the projector gt sure that the projector is correctly configurated doesn t respond to the controller gt or repair the DMX cable gt The projector is too hot Take ventilation measures to make it The beam appears dim cool 9 16 TECHNICAL DATA VOLTAGES 100V 120V 200V 220V 230V 240V AC 50 60Hz POWER CONSUMPTION 150W 220V LED Power consumption 3W Quantity 36 white 12 amber Manufacturers Rated LED Life 50000 Hours COLOURS White amber DIMMER 0 100 linearly adjustable STROBE 0 3 20F PS LENS ANGLE 14 Optional 8 45 BEAM ANGLE 32 Optional 26 54 CONTROL DMX512 3 pin interfaces 4 channels i
4. power cord come into contact with other cables Only handle the power cord by the plug Never pull out the plug by tugging the power cord Keep the optical system clean Do not touch the LED lens with bare hands When the projector is hanged to a high place please use a safety cord provided to pass through the projector handles as a secondary safety fixing for safety seasons For details refer to INSTALL THE PROJECTOR section LED lens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired for SZ example by cracks or deep scratches 2 2 Exterior surface temperatures of the projector after 5 minutes operation is 55 C when achieving steady state it is 60 C There is no user serviceable parts inside the projector do not open the housing and never operate the projector with the covers removed Always disconnect from the mains when the device is not in use or before cleaning it or before attempting any maintenance work If you have any questions dont hesitate to consult your dealer or manufacturer 3 16 INSTALL THE PROJECTOR MOUNTING HOLE SAFETY CORD FOR LAMP HOOK PASS THROUGH HANDLES When the projector is used as the left figure above unfold the support to certain angle and put the projector onto a flat surface Make sure it is steady When the projector is used at a high place as the right figure above fold the support turn it round to the top of the pro
5. the last projector in the chain The connections are illustrated below DMX TERMINATOR CONNECTION Connect a 120 OHM resistor 3 across pins 2 and 3 in an XLR plug 1200 and insert into the DMX out socket on the last unit in the chain SETUP OPTIONS PROJECTOR CONFIGURATION FUNC UP DOWN ENTER Projector configuration can be set conveniently via push button switch and LED display Launch the projector and press button ENTER for more than 5 seconds to unlock the panel the LCD will show the function menu of the projector each main menu has its submenus and each submenu has a specific function For details please see the OPERATION MENU section Press button UP or DOWN settings or enter the Press button FUNC if you want to browse through the various Setup Options Press button next menu Press button UP or DOWN to shift it will return to the upper menu one by one or browse through the main menu 5 16 ENTER to save your TO SET THE DMX START ADDRESS Each product must be given a DMX start address so that the correct projector responds to the correct control signals This DMX start address is the channel number from which the projector starts to listen to the digital control information being sent out from the controller PR 8201 have 2 DMX modes which are standard mode extended mode For example the s
6. jector connect a lamp hook to the mounting hole reserved in the support by screws and then hang the hook to a high place Eventually use the safety cord provided to pass through the handles and hang it as a second safety fixing CONTROL SYSTEM AND POWER CONNECTION DMX IN DMX OUT DMX512 1 2 2 1 PIN FUNCTION 0 s 1 1 DATA Connection between the controller and a projector and between one projector and another must be made with a 2 core screened cable with each core having at least a 0 5mm diameter Please use the projector s cannon 3 pin signal input and output cables as connection The 3 pin signal connections are connected as shown in the figure above Note Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other The body of the plug is not connected in any way The product accepts digital control signals in protocol DMX512 1990 The amount of projectors connected in parallel is not more than 32 Connect the controller s output to the first fixture s input cable with a 3 pin signal cable connect the first fixture s output cable to the second fixture s input cable and connect the rest fixtures in the same way Eventually connect the last fixture s output cable to a DMX terminator Note Only when all the start addresses of fixtures are set the same synchronous control could be achieved When the first fixture is not connected to the controller and all the other
7. n standard mode and 7channels in extended mode Master Slave mode 2 preset memories Self test mode OTHER FUNCTIONS LED board temperature display fixture usage time display DMX mode display setting status operation mode can be transmitted by synchronous control HOUSING High intensity die casting aluminum IP67 10 16 WORK ENVIRONMENT TEMPERATURE 20 40 WEIGHT 9kg SIZES AW 0 1711 428 190 107 68 48 A 0 142 36 16 9 6 4 Lux W 0 1503 376 167 94 60 42 10 8m 6m 4m 2m O d CN 2 4m M 6m 8m 10 DISTANCE m Om 5m 10m 15m 20m 25m 30m DIAMETER m 60 02 9 65 79 869 611 58 1448 17 37 11 16 LIGHT OUTPUT OPTIONAL LENS 8 Lux AW 0 1978 495 220 124 79 55 10 8m 6m 4m om 2m 2m 4m 6m 8m 10 DISTANCE m Om 5m 10m 15m 20m 25m 30m DIAMETER m 60 62 33 64 67 7 0 6 9 34 611 7 6614 01 LIGHT OUTPUT OPTIONAL LENS 459 Lux 16m 8m Om 8m 16m DISTANCE m AW 0 449 112 50 28 18 12 20m Om 5m 10m 15m 20m 25m 30m DIAMETER m 64 77 09 53 143 619 6 23 8 28 59 12 16 Power Supply 200VV DC58V LED Par Control Board SD CON SCH EARTH LED Board SD LED SCH 58V 58V gt 158V GND 2 gt GND VCC lt gt DQ DQ GND GND 2 GND E w O wr W W N lt male p
8. ower waterproof plug 4 male singal waterproof plug female singal waterproof plug EARTH COMPONENT ORDER CODES NAME PART NO QUANTITY REMARK LED LENS 070070040 48 14 LED LENS 070070015 48 8 Optional LED LENS 070070041 48 45 Optional SIGNAL CABLE 120080030C 1 1 7m male SIGNAL CABLE 120080031C 1 1 7m female SIGNAL CABLE 120080032A 1 0 3 male SIGNAL CABLE 120080033A 1 0 3 female POWER CORD 120080034C 1 1 7m male POWER CORD 120080035B 1 1 7m female POWER CORD 242810174 1 1 7m female POWER SUPPLY 192010135 1 LED CONTROL BOARD 230020237 1 LED BOARD 230060089 1 LENS TOP COVER 290080017 1 14 16 15 16 PR LIGHTING LTD PR New Hi tech Science Park 1582 Xingye Avenue Nancun Panyu Guangzhou 511442 China TEL 86 20 3995 2888 FAX 86 20 3995 2330 P N 3200050017 Version 20110120 Preliminary 16 16
9. tandard mode has 4 channels so set the No 1 projector s address 001 No 2 projector s address 005 No 3 projector s address 009 No 4 projector s address 013 and so on Launch the projector Press button ENTERI for more than 5 seconds to unlock the panel Press button FUNC IV or DOWN to find AddR menu Then press ENTER to show DMX address and press UP or DOWN to set DMX address At this time the address will flash continuously Press button ENTER to confirm and it means the setting has been enabled Press button FUNC it will return to the upper menu one by one 6 16 OPERATION MENU 1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL AddR XXX DMX address XXX 1 512 mx STd m DMX mode Con mode Default STd m d dISP ON 77 Shut off digital CRT without CNFG Default ON pressing buttons in 5 minutes Config settings mORS SLAV Slave Master Slave Settings mAST Default SLAVE Master FACT Reset factory setup yES TRmd 1 Transmit parameters y TimE Fixture usage time TEmP LED board temperature INFO VER Information Version W white AW Amber white dmx DMX mode mENU PR 01 Operation mode Preset memory PRO1 PR 01 Preset memory 2 Note 1 Parameters can be transmitted from the master projector to
10. the slave projectors in the following conditions such as display setting status operation mode and DMX channel mode 7 16 DMX PROTOCOL Standard eee ees FUNCTION DMX DESCRIPTION mode mode 1 1 Dimmer 000 255 Dimming from dark to light 2 Dimmer Fine 000 255 Dimmer in 16 Bit precision 2 3 White 000 255 Dimming from dark to light 4 White Fine 000 255 White in 16 Bit precision 3 5 Amber 000 255 Saturation from shallow to deep 6 Amber Fine 000 255 Amber in 16 Bit precision 000 No effect 4 7 Strobe 001 255 Strobe speed from slow to fast 8 16 INDICATION OF LED DISPLAY On DMX signal OK Decimal point of the first character Off No DMX signal On Master slave signal is OK Decimal point of the third character Off No master slave signal When setting master mode Decimal point of the fourth character Off When setting slave mode Parameters that LED digital tubes display Flash Parameters not saved press ENTER to save them MAINTENANCE To prolong the life of the projector it is very important to do the maintenance work The environment is hash outdoors or if the projector is idle for a long time damp smoke or particularly dirty surroundings can cause greater accumulation of dirt on its cover and housing So it should be cleaned to maintain an optimum light output and at the same time to prevent it from corrupted by acid gas Cleaning
11. ther with the projector Name Quantity Unit Remark Barn door 1 Pc Shading barrel 1 Pc Optional Safety cord 1 Pc This manual 1 Pc Single cable 1 Pc Optional Single cable 1 Pc Optional Power cord 1 Pc Optional 2 16 SAFE USAGE OF THE PROJECTOR When unpacking and before disposing of the carton check there is no transportation damage before using the projector Should there be any damage caused by transportation consult your dealer and do not use the apparatus The projector can be used indoors and outdoors IP67 The projector is not designed or intended to be mounted directly on to inflammable surfaces The projector is only intended for installation operation and maintenance by qualified personnel Do not project the beam onto inflammable surfaces minimum distance is 5m 4 5m E Avoid direct exposure to the light from the lamp The light is harmful to eyes Do not attempt to dismantle and or modify the projector in any way Electrical connection must only be carried out by qualified personnel Before installation ensure that the voltage and frequency of power supply match the power requirements of the projector It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards Do not connect this device to any other types of dimmer apparatus Make sure that the power cord is never crimped or damaged by sharp edges Never let the

PR-8201

Contents

Download Pdf Manuals

Related Search

Related Contents