User manual, Laser-products
Contents
1. Updated 9 1 2013 OPTICAL SPORTSHOOTING OWNERS MANUAL Laser products eN ai A Si IR LAA he Cro MAD Page 1 9 Manual Laser products 2013 01 09 EN 2013 01 09 Table of contents 1 GENERAL DESCRIPTION ser 3 2 HOWTOUSE TIE STE Vd oa 3 2 1 o aeetunon seer 3 2 2 rn A A e o eee 4 2 3 COCKS QING SMO EIB assunto ines 5 3 ELIP OLIE ape caerectrrnteeceneesens E ri 5 3 1 e E e e E E tale vecsensoscasn terete 5 3 2 Pe nn O poeeneanseceasewarcis 6 ZT raros 7 Ae o oo eta E setae 8 6 CHARGING THE BATTERY retarda 8 7 SAFETY INSTRUCTIONS cecsiaeriinnnast o T TT 9 8 amp 8 CLEANING AND MAINTENANCE s115 ccnccsstestacncsncneausceaneivecepnadnigedecewteeonsavecuanstalceanateiteshannecasnetnicemmabetsadeernicens 9 Page 2 9 Manual Laser products 2013 01 09_EN_2013 01 09 1 GENERAL DESCRIPTION Eko Aims optical sport shooting equipment is suitable both for practising and competitions The core of the product is its software in the circuit board with an integrated laser module This equipment is compatible with the electronic targets approved by the International Modern Pentathlon Union UIPM The laser beam can be used with either non coded beam or with a code defined by UIPM To emulate traditional shooting the gun has a so called barrel time a time a bullet would normally take to go through the barrel This shot delay is 8ms The shooter should thus take into consideration the same aspects as with a normal gun when pull2. file includes a instructions b the driver and c the program 2 Run CDM20814 Setup exe This installs USB driver for laser gun Wait until the driver is installed 4 Connect the laser gun to the USB port of the PC with USB cable and wait the PC information a Anew device has been found b Adjusting the software c Anew device is ready to be used En 5 Switch on power to the laser gun 6 Run Eko Aims Lasergun Setup v1 1 exe Program scans the laser gun automatically 7 Iflaser gun is found program shows status Connected otherwise error note will be shown and program will terminate 8 Now it is possible to adjust the G sensor sensitivity by using Read and Set sensitivity buttons 9 After adjustment is done close the program before disconnecting laser gun Page 7 9 Manual Laser products 2013 01 09 EN 2013 01 09 5 P3 EL For the initial zeroing there is 1 5 mm screw under the barrel When turning the screw clockwise the beam moves down Do not over tight the screw The final zeroing should be done by adjusting sights The rear sight is used for adjustments The Vertical adjusting adjustment screws are on the right side The upper Horizontal adjusting Screw is used for steplessly adjusting height By turning the screw the height moves upward and downward It does not matter which way the screw is turned the sight changes direction after full round The lower screw is for adjusting the sight horizontally
3. barrel is detached following the manufacturer s instructions normally by loosening two small screws on top of the barrel and carefully pulling the barrel off It is replaced with an BRU The screws are tightened again BR units are model specific The model can be found on the side of the unit For the initial zeroing there are two 1 5 mm screws on right side and under the barrel like ELP 10 When turning the screw on right clockwise the beam moves to the right and when turning the screw under the container clockwise the beam moves down Don t over tight the screws The final zeroing should be done by adjusting the sights When using the BR unit the program is automatically set for the next shot The cocking delay is 0 5 seconds The trigger unit is cocked manually by using a cocking lever Vibration censor In a BR unit the shot is recognized by a vibration sensor G sensor The power of impact caused by trigger mechanism differs between pistol types and even between copies of the same pistol type The sensitivity of G sensor has been adjusted by the factory on an average value of your pistol type If the sensitivity value is too high it might cause unintended shots On the other hand too low value might leave shots unrecognized The sensitivity can be adjusted by using Eko Aims Lasergun Setup v1 1 program Installation steps 1 Copy the file Eko Aims Lasergun Setup v1 1_release zip on your computer and unzip it This zip
4. By turning the screw clockwise the sight moves to the right anti clockwise moves it to the left 6 CHARGING THE BATTERY A gun is charged via a USB cable It can be connected to a USB port of a computer or to mains current with USB charging device A green led indicates that the battery is being charged it turns off when the battery is full Re charging an empty battery takes about three hours When the battery runs low the system gives a warning signal Page 8 9 Manual Laser products 2013 01 09 EN 2013 01 09 7 SAFETY INSTRUCTIONS LASER RADIATION DO NOT LOOK DIRECTLY AT THE BEAM CLASS 2 LASER DEVICE This is a Class 2 sport shooting device The laser follows the standard EN 60825 1 2007 type E650D1 3 1235 nominal wave length 650 nm nominal output max 1mW never direct the laser beam at another person or an animal do not look at the beam either directly or through any optical devices do not direct the beam at air planes cars windows or other similar objects use the device only in an area specified for this purpose keep away from children O O O O O O do not hand over the device to anyone who does not understand the dangers of using the laser beam it is forbidden to open or modify the device excluding the changing of battery O operating temperature 100 500 C WARNING Failure to follow these instructions may expose the user to dangerous laser radiation Read the safety instructions carefully
5. before using the device Always follow firearm regulations when handling an optical gun Carry it in a proper case or bag A person not familiar with this kind of equipment may mistake it for a regular weapon not an optical and safe one The system is meant for outdoor use as well and is protected against normal humidity and rain Nevertheless heavy rain may damage the electronic parts Always cover the gun from rain Keep itin a carrying case when not in use 8 CLEANING AND MAINTENANCE In ordinary use and normal conditions the gun is maintenance free and thus does not require any daily maintenance except a quick check In a case of malfunction please contact the manufacturer via email support eko aims com Page 9 9 Manual Laser products 2013 01 09_EN_2013 01 09
6. icro switch and a magnet form the basis for the trigger mechanism The functions of the micro switch are adjusted at the factory and should not be manipulated Any unauthorised opening of the trigger mechanism will remove any guarantee from the manufacturer s side Adjusting the trigger The trigger adjustments are set at the factory to ensure that the trigger pulling force meets the ISSF shooting rules and that everything works smoothly The user may want to adjust the trigger to fit their personal needs Adjustments are recommended to be carried out in the following order Adjust the blade angle Turning the screw clockwise will turn the blade backwards Length of double pull Turning the screw clockwise will shorten the double pull 1 5mm Allen screw 3 Trigger stop Turning the screw clockwise will shorten the after travel of trigger after triggering Caution Too close adjustment will increase the trigger force and finally prevent the trigger mechanism from travelling over the threshold Double pull pressure 150 350g Turning the screw clockwise will increase the pressure 5 Pull pressure 500g Turning the screw clockwise will decrease the pressure First stage Blade length Blade angle Second stage pressure pressure Clockwise increase Clockwise decrease Trigger stop First stage travel Clockwise shorten Page 6 9 Manual Laser products 2013 01 09 EN 2013 01 09 4 BRU 2011L The air weapon s
7. ing the trigger These laser products belong to Laser Class 2 Products have been tested by Finnish Institute of Occupational Health among classification method EN 60825 1 2007 IEC 60825 1 2007 Please read the safety instructions carefully Buttons connectors and indicator lights Switch button Charging led Information leds Charging plug Speaker Programming button 2 HOW TO USE THE SYSTEM 2 1 Start up The software in the circuit board has two modes shooting mode and menu The shooting mode is for shooting and menu for changing the settings The gun is automatically in the shooting mode when turned on The gun is turned on by using the power button on its left side Page 3 9 Manual Laser products 2013 01 09 EN 2013 01 09 In the menu mode the user can adjust the settings and options related to sound signal UIPM code and targeting mode continuous beam All adjustments are made by pressing the power button as follows Start up length not defined quick press less than 0 3 sec long press 0 3 2 0 sec O O O stop over 2 sec There are three indicator lights on the side of the weapon They indicate the activity status of the options excluding the charging status of the battery The information varies between the shooting and menu modes Information leds Others ee Ful 0 ces eee Sot Half full id Battery IPM Cocking Signals WIPM Permanent level code status code beam 2 2 Menu To go
8. to the menu press the power button shortly while in the shooting mode The first of the led lights starts flashing This indicates which of the available options is active sound signal To change the setting press the power button for 0 3 2 seconds high pitch sound signal The next option is chosen by shortly pressing the button low pitch sound signal The most recent setting is saved excluding targeting mode which can be on only in the menu mode When the gun is switched back to shooting mode or is shut down targeting mode becomes inactive Page 4 9 Manual Laser products 2013 01 09 EN 2013 01 09 Switch on keystroke Long keystroke gt 0 3 sec Short keystroke O lt 0 3 sec Menu mode Shooting mode AN Signals gt 0 3 sec Menu mode ful teni i de DD UIPM code Long keystroke gt 0 3 sec Shooting mode Qe II Zeroing Short keystroke lt 0 3 sec 2 3 Cocking and shooting The gun is cocked by using a cocking rod or a similar device or automatically after the trigger has been pulled 3 ELP 2011L 3 1 Sights The laser beam is fixed The initial zeroing has been done at the factory Adjusting the rear sight o Turning the screw on the right side clockwise will move the sight to the left o Turning the screw on top of the sight clockwise will move the sight downward Page 5 9 Manual Laser products 2013 01 09 EN 2013 01 09 3 2 Trigger unit A m
Download Pdf Manuals
Related Search