100Base-FX to 10/100Base-TX PoE Media Converter FCU
Contents
1. 11 If one of the optical conductors is bad as shown in the diagram box below the converter with LLR function will return a no link condition to its link partner With LLCF function also enabled the no link condition is carried forward to the switch hub where a trap is generated to the management station and the administrator can then determine the source of the loss Management Switch Hub Media Media Management Station Station w SNMP Converter Converter Switch Hub LFP ON pon T Broken OP Fier e e t Port 2 Port 1 1 Link Loss Carried Forward Link Loss Carried Forward Link Loss Returned LED lit established link LED unlit no link LFP function is turned on by default This feature can also be turned off via the side DIP switch If you are familiar with the network installa tion for diagnostic purpose i e check which end is broken you can turn it off and reset the converter to make it take effect Otherwise please leave it at the default position A 12 5 Installing the Converter Please follow these steps to install the PoE Media converter Turn off the power of the device station on the network to which the FCU 1802Px will be attached Ensure that there is no activity in the network Attach fiber cable from the FCU 1802Px to the fiber network TX RX must be paired at both ends Attach a Cat 5 UT2. Ethernet digital packets such as connecting the FCU 1802Px to an IEEE 802 3af complied devices AP or IP Camera 2 Checklist Your FCU 1802Px package should contain the following items e 100Base FX to 10 100Base TX PoE Media Converter x 1 e AC DC Power Adapter Input 48V DC 0 4A max x 1 e User s Manual x 1 If any items are missing or damaged please consult the dealer from which you purchased your PoE Media Converter 3 Product Outlook Overview Layout of the FCU 1802Px Rear Panel NO 7 99 2 Panel Bottom 10 100Base TX 616199 PoE Media Converter PWR Ethernet DC 10 100Base TX to 100Base FX Front Panel Left View There one RJ 45 Twisted Pair jack Auto MDI MDI X one fiber optic connector vary by model and four LED indicators OO PoE Media Converter PWR PoE 10 100Base TX to 100Base FX In Use 10 100Base TX Right View One DIP switch for Link Fault Pass Through LFP feature ON to turn on the LLCF and LLR detection And OFF to turn off this feature Please refer to the following sections for more Also one DC 48V power socket for the PoE Media Converter 48V DC LFP OFF ON 4 Link
3. LNK ACT Green over that port Lit Indicate that the port is link up Off Indicate that the port is link down Lit Indicate that the port is providing PoE in 48VDC to remote powered device Green Use Indicate that the port is not providing 48VDC to remote powered device e 100Base FX SC Port LED Color Function Indicate that the Media Converter Blink is actively sending or receiving data LNK ACT Green over that port Lit Indicate that the port is link up Off Indicate that the port is link down Fiber optic Partner should be set to the correct mode according to this FDX indicator for optimal network performance 8 Cable Connection Parameter The limitations are as below Duplex Connection Limitation max Twisted Pair Node to Node Half Full Node to Switch Hub 100 meters Multi Mode Converters Node to Node MM Half Node to Switch 412 meters MM Full Node to 2 kilometers Node to Switch Single Mode Converters SM Full Node to Node Node to Switch 15 kilometers 16 9 FCU 1802Px Technical Specifications The FCU 1802Px comes with the following standard features e Standard IEEE 802 3u 10 100Base TX 100Base FX IEEE 802 3af Power over Ethernet e Connectors One RJ 45 Auto MDI MDI X Twisted Pair EIA568 with PoE One Fiber optic 1310nm wavelength connector type vary with mod
4. breaks the FCU 1802Px link loss forwards to the switch hub that generates a trap to the management 10 station The administrator can then determine the source of the problem Management Switch Hub Media Media Switch Hub Management Station w SNMP Converter Converter w SNMP Station LFP ON LFP gt q e e ove evo e e t 1 Cable l 1 LED lit established link LED unlit no link Units are shipped with the LFP function disable OFF Link Loss Return LLR The fiber ports of the FCU 1802Px have been designed with an LLR function for troubleshooting a remote connection LLR works in conjunction with LLCF When LFP function is enabled the port s transmitter shuts down when its receiver fails to detect a valid receive link LLR should only be enabled on one end of the link and is typically enabled on either the unmanaged or remote device The diagram below shows a typical network configuration with a good link status using the FCU 1802Px for remote connectivity Note that LLR and LLCF are enabled as indicated in the diagram Management Switch Hub Media Media P Station w SNMP Converter Converter Switch Hub Station ure on FP ure orr TT gt Fiber LED lit established link LED unlit no link
5. 100Base FX to 10 100Base TX PoE Media Converter FCU 1802Px User s Manual Trademarks Copyright Antaira Technologies 2013 Contents subject to revision without prior notice Antaira is a registered trademark of Antaira Technologies The information in this manual is subject to change without notice All other trademarks belongs to their respective owners Disclaimer Antaira Technologies does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose Antaira has made every effort to ensure that this User s Manual is accurate Antaira disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of Antaira Antaira assumes no responsibility for any inaccuracies that may be contained in this User s Manual Antaira makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Warni
6. Fault Pass through LFP The LFP function includes the Link Fault Pass Through function LLCF LLR and the DIP Switch design LLCF LLR can immediately alert administrators about problems with the link media and provide an efficient solution to monitor the net The DIP Switch can disable or enable the LFP function With LLCF Link Loss Carry Forward when a device connected to the converter loses the TP line link the converter s fiber will disconnect the link of transmit With LLR Link Loss Return when a device connected to the converter and loses the fiber line link the converter s fiber will disconnect the link of transmit Both can immediately alert administrators about link media problems and provide an efficient solution to monitor the net Link Loss Carry Forward LLCF The FCU 1802Px incorporates LLCF function troubleshooting a remote connection When LFP function is enabled the FL TP ports do not transmit a link signal until they receive a link signal from the opposite port The diagram below shows a typical network configuration with a good link status using the FCU 1802Px for remote connectivity Management Switch Hub Media Media Switch Hub Management Station w SNMP Converter Converter w SNMP Station LFP ON LFP ON gt PE Fiber 9 0 LED lit established link LED unlit no link If the connection
7. P cable from the 10 100Base TX network to the RJ 45 port on the FCU 1802Px Connect the 48V DC power adapter to the FCU 1802Px and verify that the Power LED is lit Turn on the power of the device station the TX Link and FX Link LEDs should light when all cables are attached FCU 1802Px TX RX SD gt RX TX E 100Base FX Fiber Network 10 100Base TX Cat 5 5e TP Cable Network RJ 45 STP UTP Cat 5 straight crossover cable is accepted e Please refer to section 9 for more about the wiring distance of your TP Optic fiber networks 6 PoE function FCU 1802Px and the IEEE 802 3af Injector Splitter equipment installation Before your installation it is recommended to check your network environment If there is any IEEE 802 3af devices that need to power on the FCU 1802Px can provide a way to supply power for this Ethernet device conveniently and easily The FCU 1802Px comes with an AC DC adapter with DC 48V input and injects this DC power into the pin of the twisted pair cable pair 1 2 and pair 3 6 207 15am 100 meters FCU 1802Px PIN Datta Power Pot Wiretess AP Fiber Switch A 14 7 LED indication e System LED Color Function PWR Green Lit Indicate the device is powered 10 100Base TX Port LED Color Function Indicate that the Media Converter Blink is actively sending or receiving data
8. el e Data Transfer Rate 10 100Mbps TP 100Mbps FX e Duplex mode support Full or half duplex mode by Auto Negotiation TP e LED indicators PWR FX LNK ACT TX LNK ACT PoE in Use e PoE Power Output 48V DC Max 15 4 watts 350mA e Power Pin Assignment 1 2 3 6 End Span e Power Supply 48V DC 0 4A external AC DC adapter e Ambient Temperature 0 to 50 C operating e Humidity 5 to 90 non condensing e Dimension 26 x 70 x 97mm H x W x D e Cable UTP Cat 5 UTP cable e Fiber MM 50 125 or 62 5 125 optic fiber e Fiber SM 9 125 um optic fiber Connecting to Router Bridge or Switch Hub please refer to the device s Technical Manual APPENDIX A Device s RJ 45 Pin Assignments 10 100Mbps 10 100Base TX Contact MDI MDI X 1 1 TX 3 2 2 TX 6 3 3 RX 1 6 6 RX 2 4 5 7 8 Not used Not used Implicit implementation of the crossover function within a twisted pair cable or at a wiring panel while not expressly forbidden is beyond the scope of this standard A 2 RJ 45 cable pin assignment DD 2 There 8 wires a standard UTP STP cable and each wire is color coded The following shows the pin allocation and color of straight cable and crossover cable connection 18 Straight Cable SIDE 1 12345678 SIDE1 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 12345678 SIDE2 6 7 Wh
9. ite Brown 8 Brown SIDE 1 SIDE2 6 Green 7 White Brown 8 Brown SIDE1 1 White Orange 78 2 Orange 3 White Green 4 Blue 5 White Blue 78 SIDE 2 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown SIDE2 1 White Green 2 Green 3 White Orange 4 Blue 5 White Blue 6 Orange 7 White Brown 8 Brown Figure A 1 Straight Through and Crossover Cable Please make sure your connected cables are with the same pin assignment and color as the above picture before deploying the cables into your network A 3 Fiber Optical Cable Connection Parameter The wiring details are as below e Fiber Optical patch Cables Standard Fiber Type Cable Specification 100Base FX x 1310nm Multi mode 50 125um 62 5 125 100Base FX 1310nm Single mode 9 125um This page is intentionally left blank
10. ng This equipment has been tested and found to comply with the regulations for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with this user s guide may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Energy Saving Note of the Device This power required device does not support Standby mode operation For energy saving please remove the DC plug or push the hardware Power Switch to OFF position to disconnect the device from the power circuit Without removing the DC Plug or switching to OFF the device will still consume power from the power source In the view of Saving Energy and reducing unnecessary power consumption it is strongly suggested to power off or to remove the DC plug for the device if this device is not intended to be active WEEE Warning To avoid the potential effects on the enviro
11. nment and human health as a result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately Revision User s manual for Antaira 100Base FX to 10 100Base TX PoE Media Converter Rev 1 1 April 2013 Part No 2350 AA3540 470 Table of Contents 1 os erede oup ots siete Seu eeu ed 6 2 Model Dist t REN Hau 7 3 ChecklisE uio INIT 7 4 Product Outlook aset eiecit breuis 8 5 Link Fault Pass through LFP ceeeeeeeeeeeeeeeeeeeeeeeeeeaee 10 6 Installing the 13 7 POE TUNCHOM cre act eM 14 8 PED indication MRKO 15 9 Cable Connection 16 10 FCU 1802Px Technical 17 APPENDIX A 191 1i E E 18 1 Device s RJ 45 Pin Assignments 18 A 2 RJ 45 cable pin 18 Fiber Optical Cable Connection Parameter 19 1 Overview Thank you for purchasing Antaira s FCU 1802Px family of 10 100Mbps Etherne
12. t Twisted pair to 100Base FX Fiber optic PoE Bridge Converter This converter is used to convert one type media signal to another easily efficiently and inexpensively The converter provides Power over Ethernet power injector function which is able to drive one IEEE 802 3af compliant powered devices About the Power over Ethernet Injector The FCU 1802Px has an IEEE 802 3af Power over Ethernet Injector that provides DC 48V over Ethernet cables The FCU 1802Px IEEE 802 3af Power over Ethernet Injector inserts DC Voltage into Cat 5 cable allowing the cable between the Injector FCU 1802Px and PoE PD Powered Device to transfer data and power simultaneously The maximum distance between the Injector FCU 1802Px and PoE PD is 100 meters With the FCU 1802Px installed it combines the Ethernet digital data with power over the twisted pair cables as an IEEE 802 3af Power over Ethernet Injector And the IEEE 802 3af Power over Ethernet splitter shall separate the digital data and the power into two outputs With IEEE 802 3af Power over Ethernet devices installed the system administrator only has to use a single RJ 45 Ethernet cable to carriy both power and data to each device Aside from connecting through the FCU 1802Px and PoE PD you can also have the benefit of cost saving easy for networking planning and higher reliability Moreover upon any IEEE 802 3af device installation the FCU 1802Px or PD can make the connection while migrating the
Download Pdf Manuals
Related Search