Ax49-50-51 Quick Guide
Contents
1. Rev 141120 Network Dome Camera 13 INTERNATIONAL Quick Start Guide Ax49 50 51 series SAFETY When installing your Ax49 Ax50 Ax51 camera be sure to avoid e excessive heat such as direct sunlight or heating appliances contaminants such as dust and smoke strong magnetic fields sources of powerful electromagnetic radiation such as radios or TV transmitters moisture and humidity areas with mechanical vibrations fluorescent lamps or objects that reflect light unstable light sources as this may cause flickering temperatures below 10 Celsius or 14 Fahrenheit and above 50 Celsius or 122 Fahrenheit e For more details on installation and operation please refer to the CD provided POWER SUPPLY Ensure the supplied voltage meets the power consumption requirements of this camera before powering the camera on Incorrect voltage may cause irreparable damage to the video camera and will effectively void the camera warranty CLEANING e For maximum optical clarity the camera dome or lens must remain clean Use a soft dry cloth to remove finger prints or dust from the dome cover e Use a blower to remove dust from the lens e Clean the body with a soft dry cloth If it is very dirty use a cloth dampened with a small quantity of neutral detergent then wipe dry e Do not use volatile solvents such as alcohol benzene or thinners as they may dam age the surface finishes SERVICING To avoid electrical2. shock and to preserve the product warranty DO NOT disasembles the camera Refer servicing to qualified personnel only PACKAGE CONTENTS 1 Flat Head Screw Machine Type x4 2 Flat Head Screw Tapping Type x4 3 Plastic Anchor x4 4 Plastic Mounting Button x4 5 Rubber Feet x4 6 Guide Pattern Sticker x1 7 8 9 Printed Quick Start Guide x1 CD User Manual Annexxus Finder x1 RJ45 Female Female Coupler x1 0 Fully Assembled Network Dome Camera x1 13 TRNG CAMS Ax49 50 51 series QuickGuide indd CAMERA PARTS AND DEFINITIONS a gt Nae is 2 3 m Power In Red Black Power connector DC12V AC24V absent on Ax49D Ax50D RJ 45 Ethernet Connector Supports PoE Power over Ethernet BNC Video Output MOUNTING THE CAMERA SURFACE MOUNT 1 2 Adhere the Guide Pattern Sticker to the desired location on the mounting surface and mark hole positions Drill 4 mounting holes and 1 cable entry hole on the mounting surface ac cording to the guide sticker Secure the metal plate to the ceiling using the appropriate screws Use machine type screws if you are attaching the camera to a pendant mount Use tapping type screws for all other surfaces For cement surfaces insert the Plastic Anchors into the holes For softer surfaces do not use the Plastic anchors Use the Rubber Feet for surface mounting ADJUST CAMERA POSITION 1 Remove the screw on the base of the camer
3. Change the IP address on the onboard NIC LAN or on NIC1 if your SRX Pro Server has two onboard NIC cards of your SRX Pro Server to 192 0 0 XXX to match the default IP range of your Annexxus IP camera Connect your camera to i3 SRX Pro Server see diagram above Turn on your Annexxus camera Launch the CD that came with your Annexxus camera and double click AnnexxusFinder exe file to install Annexxus Finder application Annexxus Finder application discovers all Annexxus cameras connected to your network Select desired camera in the Annexxus Finder software by double clicking it in the list and click Edit Enter the new IP address and Subnet Mask of the camera in the Change IP Address area The new camera IP address must match the original range of your SRX Pro LAN or NIC1 card E g If your original SRX Pro Server s IP address was 192 138 10 122 change your Annexxus camera s IP address to 192 138 10 XXX Follow the Annexxus Finder installation instructions until the application has been successfully installed on your SRX Pro Server Double click Annexxus Finder icon on the Desktop to launch the application The application window will appear displaying a list of active network cameras Remember Annexxus Cameras cannot share an IP address each camera requires its own unique IP address Enter the default camera password in the Input Password field and click Save Wait a few moments for a successful confirmation window Click OK to clo
4. a a _ lt lt lt lt lt Screw a Rev 141120 2 3 4 s lt a i3 INTERNATIONAL INC eer QUICK START GUIDE Rotate the dome counter clockwise to unlock and pull free of the housing Service Monitor z Guide Pattern Output J Se s Rubber Feet Inner gt i Lining Tapping Type lt lt Dome Screws ra pou nh Remove the inner liner by gently pulling it free of the two notches in the housing Adjust the tilt of the camera as necessary Adjust the pan of the camera as necessary Horizontal Rotation Pan Angle about Tilt Angle 90 degrees 355 degrees Note Maintain tilt at 75 degrees or less to avoid distortion See the image below to locate the distortion angle of the camera Distortion Area 24 Wide Angle 9mm 75 Tilt Angle ee 68 Tele Angle 3mm Note The diagram above does not apply to Ax51 series cameras www i3international com Ax49 50 51 series Network Dome Camera CONNECT CAMERA TO 13 SRX PRO SERVER Connection type 1 CI S Crossover direct connection Connection type 2 3 gt VIA a Gigabit Switch i3 SRX Pro Server Camera s default IP 192 0 0 16 Firmware Version AP_01 00 60 33 i02 Login admin Password 1234 Firmware Version AP_01 00 60 35_i02 or higher Login iZadmin Password i3admin i3 SRX Pro Server Close SRX Pro Server software by pressing Alt Shift Ctrl F4
5. rame rate for the Annexxus camera in the IP Camera tab menu or you may choose to configure the camera s settings U S A 1967 Wehrle Drive Suite 1 Canada 780 Birchmount Road Unit 16 PMB 034 Buffalo NY 14221 Scarborough ON M1K 5H4
6. se it Repeat Steps 1 12 for all detected Annexxus cameras in the Annexxus Finder Make sure you can connect to the camera through Internet Explorer Launch Internet Explorer and enter the IP Address you have just assigned to your Annexxus camera The password window should be displayed Enter the default camera User Name and default Password Annexxus camera interface will be displayed in the Internet Explorer window You should be able to see the camera image on the screen If you do not see the camera image on the screen call i3 International tech support for troubleshooting tips 1 877 877 7241 Make sure that the latest version of GiPi updater is installed on your SRX Pro Server You can download the updates from ftp files 123ip com drivers gipi Please contact i3 Technical Support team for access information Once the latest GiPi updater has been installed restart i3 SRX Pro Server software Log In and go to the Setup gt IP Camera tab Click the Search button to display connected Annexxus cameras select the detected camera in the list and click Select Inthe Select IP Camera window enter the default camera User Name and the default Password then click Add The selected camera will be added to the IP Camera list Don t forget to assign the IP camera to the SRX Pro video channel in the corresponding column Your Annexxus camera is now connected to SRX Pro Server and is ready to record You may change resolution and f
Download Pdf Manuals
Related Search