Lite H.264 DVR
Contents
1. lt Pelco D gt lt Pelco P gt lt Fastrax 2 gt lt JVC gt lt Panasonic_C gt and lt Panasonic_N gt The default is lt None gt Note that ID number must match the ID address defined by the dome camera e To configure the RS 485 parameters select lt System Setup gt from OSD main menu and then select lt RS485 Setup gt The default RS 485 settings are 9600 Baud 8 Data Bits 1 Stop Bit and No Parity Control Buttons in Dome Camera Control Mode Hi 264 DIGITAL VIDEO RECORDER REC ir ENTER sga dai 4 eL t SEARCH MENU 7 8 9 10 11 12 13 Set GoPreset_ 5 ESC 9 FocusFar____ 13 Zoomin Toggle Hint Screen 6 Pan Tilt O D Enter Dome Camera n 4 Enter Auto 8 FocusNear_ 412 Zoom Out Basic Playback Operation Search By Time Press SEARCH to enter the Search menu Move the cursor to From and press ENTER will start playing recorded video from the specified From time Move the cursor to End and press ENTER will start playing recorded video from the specified End time Move the cursor to Select and press LEFT RIGHT to choose date time Press ENTER and adjust the values by UP DOWN keys Press ENTER again to confirm or press ESC to abort Move the cursor to lt Begin Playback gt and press ENTER to start playing back recorded video of the selected time Press PLAY STOP again to return to live video A NOTE If there is no available recorded video that matc2. the DHCP to lt ON gt The IP address Netmask Gateway and DNS settings are retrieved from network servers DHCP is dynamic that the settings change from time to time e For Non DHCP user set the DHCP to lt OFF gt Enter an IP address Netmask Gateway and DNS settings Please obtain the information from the network service provider e To change the IP address Netmask Gateway and DNS value press UP DOWN keys to move the cursor to the item Use LEFT RIGHT keys to access each section of the value and press ENTER then change the value using UP DOWN keys e PPPoE users must set the lt PPPoE Account gt lt PPPoE Password gt and lt PPPoE Max Idle gt as well e When the settings are complete press ENTER to confirm and save the settings or ESC to abort Dome Camera Control Dome Camera Connection amp Settings e See section Pin Definition of Alarm I O amp RS 485 and Audio In for RS 485 port pin definition e Refer to the following figure Connect the R R terminals on the dome camera to the D D terminals on the RS 485 port by RS 485 cable respectively CH3 CHS CH CH9 CH 11 CH 13 CH 15 We AEN A el AEN EN EN ENS AEN NCA ANY CA USF US BEN CA PAE NE OV AEAN T AEN N AA AA QZ QZ YZ QT NX NZ wr g CH4 cue che CH 10 CH 12 CH14 CH 16 e To set up dome camera s protocol and ID press MENU to access the OSD main menu and select lt Camera Setup gt The available protocols include lt DSCP gt lt AD422 gt
3. the Playback controls To end the playback click lt Live gt to return to live video Playback Local avi Files Start the windows media player or other media player from lt Start gt menu or any other possible access Select lt File gt and then lt Open gt Select the wanted avi file and click lt Open gt A NOTE The avi files for each channel are stored separately Therefore the video can be played back in single channel full screen mode only Playback Event Video Click SEARCH on the main window toolbar The Event List appears Scroll through the Event List and highlight the interested events Double click on the desired event to view the event video Playback Controls Fast Backward Fast Forward Step Backward Step Forward afd Play Pause Mobile View Software Mobile View software allows users to timely monitor via a mobile device with internet connection Refer to below for brief introductions of installation JAVA mobile devices and basic operations Download and Installation Access the java installation menu on a JAVA mobile device and connect the website that provides Mobile View software to directly download the software to the mobile device After the download is completed follow the instruction shown on the JAVA mobile device to installed Mobile View software Basic Operation Locate the installed Mobile View software and launch it The main window will be shown as below on th
4. D AR Alamin7 21 Alarm In 12 16CH 4 RS485D M3 Alarming 22 Alarm In 13 16CH 5 Reserved 14 Alarm Out Close 23 Alarm In 14 16CH 6 Alamini M5 Reserved 24 Alarm In 15 16CH 7 Alamin2 46 Reserved 25 Alarm In 16 16CH 8 jAlamin3 M7 Reserved 9 Alarmin4 AB Alarming 16CH PP Audio In Pin Definition Pin Definition Pin Definition Pin Definition Zim 8 Audio 15 16CH Audio4 22 GND 2 Audio3 9 GND Audio6 23 GND_ _ 3 Audio5 10 17 Audio8 24 GND_ 4 Audo7 M Audio 10 16CH 25 Reserved 5 Audio 9 16CH 12 Audio 12 16CH J sd Audio 11 16CH 13 Audio 14 16CH sd 7 Audio 13 16CH 14 Audio 2 Audio 16 16CH o lt Power On the DVR Please follow the proper power on procedures to avoid damaging the DVR e Connect all necessary components e g monitor and cameras before power on the DVR e Check the type of power source before connecting the power adaptor to the DVR The acceptable power input is between AC110V AC240V Select Viewing Mode e Press MODE repeatedly to select the wanted display mode The available viewing modes are full screen 2x2 3x3 and 4x4 split window e Press FREEZE to pause the current viewing image e Refer to the following for a brief description of some icons that will be shown on the monitor Icon Description _ Position Icon Description _ _ _ Position amp Playback
5. Lite H 264 DVR Setup Guide Package Content Inspect the packaging carton Make sure the Lite H 264 DVR is properly delivered Remove all items from the box and make sure the box contains the following items Lite H 264 DVR SATA Cable FONET Power Cord Jers Adaptor Manual 2 Front Panel 1 2345 67 8 6 ieiic PASAI Mias a REC R ENTER sga dai 4 AeL 8 SEARCH MENU 9 10 11 12 13 14 15 16 17 18 In Live and Playback modes press any key to view the corresponding video in full screen Channels In input interface 1 10 can be used for direct input of numbers 0 9 In Dome Camera Control mode 1 is for entering the Set Go preset menu 2 is for hiding or displaying the hint screen 11 16 is for quick access of preset points 1 6 Power LED It lights up when power source is connected EE Alarm LED It lights up when an alarm is triggered 4 Network LED It lights up when network is connected In addition it blinks when data is being transmitted via the network Record LED It blinks when videos are being recorded 1 In OSD menu or selection interface press these key to make the selection or save settings 2 In live full screen viewing mode press this key to view a 2x zoom image press it again to return 7 Press this key to cancel or exit from certain control mode cursor to previous or next fields To change the value in the selected field press UP DOWN keys i u
6. Mode Lower left corner mO Key Locked Center bottom Not Logged in Upper right corner User s Authority Level Upper right corner Basic Setup Enter the OSD main menu and setup some basic configuration of the DVR The basic configuration can be set via either the DVR or DVRRemote the remote software Enter OSD Main Menu e Press MENU to enter the OSD main menu e Enter username and password The default username and password is admin and 1234 e Press MENU again to quickly input the default username admin e Itis strongly suggested to change the password to prevent unauthorized access Date Time Setting Follow steps below to setup date time before the recording starts e Select lt Date Time gt in System Setup menu e Select the date and time using LEFT RIGHT keys then adjust the value using UP DOWN keys e The new date and time settings take effect after the changes are confirmed Language Setting If users wish to change language of the DVR system follow the steps below e Select lt Language gt in System Setup menu and press ENTER e Press the UP DOWN keys to select the desired language Network Setup Configure the LAN setup for the DVR to properly function with Ethernet connection e From OSD main menu select lt System Setup gt gt lt Network Setup gt set the lt LAN Select gt item to lt LAN gt or lt PPPoE gt according to the network application and enter lt LAN Setup gt e For DHCP user set
7. Type the IP address of the unit in field and click lt Add gt to add this website to the zone e In the Security Level area click lt Custom Level gt Under lt ActiveX controls and plug ins gt set all items to lt Enable gt or lt Prompt gt e Click lt OK gt to accept the settings and close the lt Security Settings gt screen Using the Remote Software e Start the IE and enter the IP address of the Lite H 264 DVR in the address bar e The ActiveX controls and plug ins dialog will show twice for confirmation click lt YES gt to accept ActiveX plug ins The DVRRemote plug ins will be downloaded and installed on the PC automatically when the connection is successfully made A NOTE Do not enter any leading 0O characters in the address for example 192 068 080 006 should be entered 192 68 80 60 NOTE If the default trigger port 80 is changed into another one port 81 for example A then the IP address should be entered as 192 68 80 6 81 e Version verification starts automatically to verify whether DVRRemote was installed This process may take up to 30 seconds e When the software is completely downloaded and installed the Login Screen is displayed e Enter the username and password The default usernames and passwords are admin 1234 and user 4321 The following picture shows the display window of the DVRRemote 7 8 9 10 11 12 13 14 15 16 17 S A A ae r A A A kemale mal LI
8. VE MENU SEARCH smarimor f MODE HH EH cem a Refer to the table below for brief description of functional items Item Description Item Description Instant Recording Search Event List Smoothen the Image Capture Snapshot Deflicker On Off at Playback 4 3 Viewing Aspect T View Live Camera 8 Playback Video A7 Download DVRPlayer 9 SetupMenu I T T For more information on DVRRemote see User s Manual Playback Control 1 10 2 11 3 12 4 Audio On Off 13 HDD Status 5 14 6 15 7 16 DVRRemote Playback Playback Remote Video Click lt Play gt on the main window toolbar and then lt Remote Playback gt tab The lt From gt and lt To gt on top of the screen display the date and time from which recorded video is available for playback Choose lt Playback gt in lt Select gt field for playback recorded video Select the date and time of the segment to play back from the lt Start gt field The date and time can be changed either by typing desired numbers directly or using the arrow buttons Click lt OK gt to start the playback or click lt Close gt to abort Playback Local drv File Click lt Play gt on the main window toolbar and then lt Local Playback gt tab Click lt Open gt and the file selection screen is displayed Select the drv video file to playback and click lt OK gt Click lt OK gt to start the playback or click lt Cancel gt to abort View the video playback using
9. e left Access lt Connect to device gt and users can create bookmarks for DVRs or IP cameras via entering hostname IP address port username and password of the devices If a DVR is connected the available functions will be listed as shown above on the right Users can select lt Live Monitoring gt to view the live video lt Normal Playback gt and lt Event Playback gt allow users to playback recorded normal and event videos lt Menu Config gt enables users to setup part of the DVR s configuration If an IP camera is connected live video of the IP camera will be directly shown on the screen lt Snapshot Viewer gt is where the snapshot pictures can be viewed after they are saved to the database of the mobile devices Refer to Mobile View Software User s Manual for installation on Black Berry phones and detailed information of all functions 10
10. hes the specified time and date the unit starts to playback from the next available video Calendar Search Press SEARCH to enter the Search menu Move the cursor to lt Calendar Search gt and press ENTER A calendar will show up Move the cursor to year month and press ENTER Then press UP DOWN to adjust the value and press ENTER again to confirm Move the cursor to select any day shown in bold font and a time ruler will be displayed Press ENTER and an arrow will show up above the time ruler Press LEFT RIGHT to select a desired time Alternatively move the cursor to the time shown at the bottom Press ENTER and adjust the values of hour minute second via UP DOWN keys Note that the time blocks highlighted in red represent events occurred Move the cursor to the playback icon gt and press ENTER to start playing back the video Search by Event Press SEARCH to enter the Search menu To search event video that was recorded on a specific camera use LEFT RIGHT keys to move the cursor and press ENTER to select or de select a channel Move the cursor to lt Event List gt and press ENTER to list the event video of the selected channels The list displays each event by date time triggered camera and alarm type The latest recorded event video will be listed on the top To exit the event list press ESC Use UP DOWN keys to scroll through the Event List Press ENTER to play back the selected event record NOTE The event lis
11. nit such as a USB ThumbDrive or a USB mouse Press this key to enter Call Monitor Control mode 8CH amp 16CH models only 1 In Zoom mode these keys function as normal direction keys 2 In the OSD setup menu the direction keys are used to move the Direction Keys OOPSL3080ZSEA4 1 m COPY This key is used for marking te in quick video export function 42 DOME Press this key to enter Dome Camera Control mode 43 SEQ Press this key to start automatic sequence display of cameras 14 FREEZE Press this key to freeze the current viewing screen 45 PLAYISTOP Press once to start the playback of recorded video Press again to ext 416 MODE Press this key to view in fullscreen or multiple window modes 18 menu Press this key to enter he OSD setup menu Rear Panel The DVR is capable of networking Once the unit is connected to the LAN LAN 10 100M network users can remotely access the DVR through the remote RJ 45 software on a PC The DVR can connect to a monitor via an optional VGA connector VGA optional Audio In connectors are for the DVR to connect audio source devices Audio In For 4CH models 4 RCA Audio In connectors will be provided whereas for 8CH and 16CH models a D Sub Audio In connector is provided Call Monitor Audio Out RCA connectors are provided for the DVR to connect audio output devices e g amplified speakers GCH amp 16CH models only The call monitor is used to display full sc
12. reen video of all installed Call Monitor cameras in sequence The BNC Call Monitor connector allows users to BNC connect the DVR with an optional call monitor CH amp 16CH models only Video In A group of BNC connectors is provided for video input streams from BNC installed cameras USB Port This USB port allows users to connect a PS 2 mouse via a converter Alarm I O amp The DVR provides alarm I O and RS485 ports that offer users the RS 485 flexibility required to connect the DVR to other devices Main Monitor Main Monitor Audio Out RCA connectors are provided for the DVR to Audio Out connect audio output devices e g amplified speakers Call Monitor Audio Out hen Monitor The DVR can connect to a monitor via a BNC connector The DVR has a free voltage DC power connection jack Please connect Power Jack the power supply adapter shipped with the unit Pin Definition of Alarm I O amp RS 485 and Audio In Alarm I O amp RS 485 4CH models Pin Definition Pin Definition Pin Definition Pin Definition 1 Alarm Out Open 5 Alarmin1 9 Alarm Out Close 13 GND ___ 2 AlarmOutCOM 6 Alarmin2 40 GND _ 44 GND 3 RS485D 7 Alamin3 41 GND AS GND 4 RS485D 8 Alarmin4 42 GND L y 8CH amp 16CH models Pin Definition Pin Definition Pin Definition 1 AlarmOutOpen 10 AlarminS M9 Alarm In 10 16CH 2 AlarmOutCOM_ M1 Alarmin6 20 Alarm In 11 16CH 3 RS485
13. t displays only the first 1024 events as some events are deleted A others are displayed Playback Controls Button Description LEFT The button is for rewinding the recorded video while playing back Press the button repeatedly to increase the speed of reverse playback by 1x 2x 4x 8x 16x or 32x RIGHT The button is used to play the recorded video fast forward Press the button repeatedly to increase the speed of forward playback by 1x 2x 4x 8x 16x or 32x Press FREEZE to pause the playback video When the recorded video is paused press LEFT RIGHT to resume playback video single step reverse forward respectively Press FREEZE again to continue playing back video Play Stop Press to start the playback or to stop playing back video and return to live mode Connect the DVR via the Remote Software Setup Requirements e Make sure the PC is connected to the Internet e Obtain IP address of the Lite H 264 DVR To check the DVR s IP address press MENU on the front panel and select lt System Setup gt gt lt Network Setup gt gt lt LAN Setup gt gt lt IP gt to check the IP Changing Internet Setting e Start the IE select lt Tools gt from the main menu of the browser then lt Internet Options gt and then click the lt Security gt tab e Select lt Trusted sites gt and click lt Sites gt to specify its security setting e Uncheck Require server verification https for all sites in this zone
Download Pdf Manuals
Related Search