USER MANUAL
Contents
1. USER MANUAL STANDARD 48 MONTH WARRANTY Your ETS Distributor including ETS Inc if purchased directly through manufacturer s warranty warrants your tanning unit to be free of structural defects in material and workmanship under normal use for its lifetime Your ETS Distributor will at its discretion repair any structural defect which materially affects the performance of the tanning unit or replace the tanning unit For forty eight 48 months following the shipping date of your tanning unit your ETS Distributor will provide replacements for parts that prove to be defective in material or workmanship Fluorescent lamps and lamp starters are warranted against manufacturer s defects for a period of ninety 90 days following the shipping date of your tanning unit Acrylics will be warranted against manufacturer s defects for a period of 2 years prorated Labor costs associated with repair or replacement work covered by this warranty will be reimbursed for repair or replacement work required to be performed for a period of one 1 year following the shipping date of your tan ning unit Normal wear and tear damage from misuse or abuse damage incurred in transit or damages resulting from unauthorized repairs or modifications are not covered by this warranty Warranty coverage does not include cosmetic abnormalities such as scratches nicks dents or other cosmetic changes that do not materially interfere with the function of2. 2 Package Contents copre E RR tie terse e es 2 Operation 22i pen iem e E re 3 Before You Tan 3 Exposure Times 3 Using Your Sunbed oie Ree URGET teet e en 4 SETUD uoce lu eh eleme ese 6 Stereo Installation Ret RED PEERS 6 Remote Connections 7 Care and Maintenance 11 Cleaning After Usen cei iss ey a ARR RCM RR 11 Thorough Periodic Cleaning 11 Mechanical Inspection 11 Lamp and Acrylic Replacement 12 Bench its ane Rete sia 18 Technical 19 Setting Operating Parameters 19 Troubleshooting 543 0 od DD eR eg en 22 Power Hookups sens Eos sa a C PRU Un 25 Safety Information LABELING NOTICE Labels are affixed on all systems to inform the user of possible dangers Regulations are stated in 21 CFR Section 1040 20 and require that all products manufactured after September 8 1986 which use sunlamps must display the following D ANGE Ultraviolet radiation Follow instructions Avoid overexposure As with natural sunlight overexposure can cause eye and skin injury and allergic reactions Repeated exposure may cause premature aging of the skin and skin cancer
3. Normal IV Dark DANGER Some medication may increase your sensi tivity to ultraviolet light It is recommended that you consult a physician before using this sunbed if taking any medication or if you suspect that your skin might be especially sensitive to sunlight DANGER Shock hazard Do not operate this device near water or while you are wet Exposure Times Follow the guidelines for skin type and exposure times as shown in the table below Untanned persons should not tan on consecutive days during their first week of tanning Never tan more than once day Tanning normally appears after the first few sessions and maximizes after approxi mately four weeks Tan once or twice per week thereafter to maintain appearance Persons already having base tan may begin at advanced levels corresponding to the extent of their base tan MAXIMUM EXPOSURE TIME IS 10 MINUTES Subsequent Level 4 Maximum Level 2 Level 3 NOT RECOMMENDED FOR TANNING 10 10 6 8 10 10 VLI0O c Z9c 26732 01A Operation Using Your Sunbed Using Your Sunbed A 58 84358 A Timer button Turns bed on Timer dis 1 Shoulder Tanner Status ON or OFF play shows remaining time If a lesser time is desired press timer button until desired time is displayed Face tanner status OFF LOW HI Remaining time B Timer display Displays session status Body fan status LOW MED
4. Sensitive Skin Burns easily and severely and does not tan NOT RECOMMENDED FOR TANNING l Light Burns easily and severely and tans minimally 2 4 6 8 10 Normal Burns moderately and tans average 3 5 7 10 10 IV Dark Burns minimally tans easily and above average 4 10 WARNING Read the instructions booklet before using this sunlamp product All persons in the room should wear protective eyewear when lamps are on Recommended eyewear provided eyeshields or equivalent eyewear as defined under 21 CFR 1040 20 Other types of eyewear may not provide adequate protection Failure to use protective eyewear may result in severe burns or other eye injury If dis comfort develops discontinue use and consult a physician ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THIS EQUIPMENT BRONZING SUN GOLD Wolff amp Model BSG 71 T12 200W VS R BI PIN SPEED 525VS R Wolff Model SPD71 T12 525VS R 200W Bi Pin Heraeus OH 30 50 or Heraeus OH 24 50 facial unit MARQUIS Wolff System amp Model CF26W shoulder unit DISCONNECT POWER BEFORE ATTEMPTING TO CLEAN RELAMP OR ENGAGE IN THE MAINTENANCE OF THIS PRODUCT ANTERTE THIS EQUIPMENT MUST BE EARTH GROUNDED This product is in conformity with performance standards for sun lamp products under 21 CFR PART 1040 20 and 0 Us LISTES ANSI UL Standard 482 Certified to CAN CSA Standard C22 2 NO 224 88465 iii 10 26790 26732 01 Renseignements sur la s curit
5. D ANGE Rayonnement ultraviolet Veuillez suivre les instructions vitez une exposition excessive Tout comme pour les rayons du soleil une exposition excessive peut causer des blessures aux yeux et la peau et provoquer des r actions allergiques Une exposition r p t e peut causer le vieillissement pr matur de la peau et provoquer le cancer de la peau PORTEZ DES LUNETTES PROTECTRICES LE NON RESPECT DE CETTE CONSIGNE DE S CURIT PEUT ENTRA NER DE GRAVES BR LURES OU DES L SIONS OCULAIRES LONG TERME Les m dicaments ou les produits cosm tiques peuvent aug menter votre sensibilit au rayonnement ultraviolet Consultez un m decin avant d utiliser la lampe solaire si vous prenez des m dica ments si vous souffrez d une maladie cutan e ou si vous croyez tre particuli rement sensible aux rayons du soleil Si vous ne bronzez pas au soleil il est peu probable que vous bronzerez sous une lampe solaire Les enfants les personnes g es et les personnes qui ont une peau claire qui br le facilement ne bronze jamais ou alors tr s peu ne devraient pas utiliser cette lampe tendez vous sous la partie sup rieure puis abaissez celle ci aussi bas que possible en veillant cependant conserver un espace d au moins 6 5 pouces 16 5 centim tres entre le corps et le panneau de plastique transparent de la partie sup rieure et le panneau de plas tique transparent de l appareil de bronzage lat rales afin d viter une exposition excess
6. HI See right a C N Volume status OFF 1 10 C Stop button nterrupts tanning session Shoulder tanner control Turns ehp ldar Tanner onand of See next page for operating instructions The timer is programmed at the factory Face tanner control Adjusts intensi with start up defaults To modify these see ty of Face Tanner Setting Operating Parameters Body fan control Controls the speed of the body fan during use Volume control Adjusts music level WARNING Wear protective eyewear Failure to may result in severe burns or longterm injury to the eyes Operation Using Your Sunbed Operation as a stand alone unit or connected to Operation while connected to a T Max remote a remote system using a control relay If using Max see right 1 face up lower toward your body using the canopy handle Maintain at least 6 5 16 5 centime ters between the canopy and your body Put on your safety goggles Press the START button see previous page to begin the tanning session The unit will turn on and the timer will begin to count down If a lesser time is desired press the START button until the desired time is displayed When the timer reaches 0 00 the lamps turn off If you want to stop your session before time expires press the STOP button You will have ten sec onds to restart with the remaining time otherwise the session will end Raise th
7. RJ TO CANOPY TRAY Cl tm LJ ci LJ 25 VLO TELIT 26732 01 Technical Information Power Hook up BUCKBOOSTER WIRE DIAGRAMS FOR THREE PHASE UNITS BOOST OF 24 OR 32 VAC BOOST OF 12 OR 16 VAC BLACK RED WHITE BLACK RED WHITE LEADS LEADS LEADS LEADS LEADS LEADS BUCK OF 24 OR 32 VAC BLACK WHITE BUCK OF 12 OR 16 VAC RED LEADS LEADS LEADS HEP 26 Size 99 71 251 5cm 180 3cm Weight 1431 lbs 650 kg Recommended Room Size 10 x 10 3m x 3m Electrical Voltage AC 220 Amperage 49A 3 phase 85A 1 phase Outlet Sunbed hardwired Subwoofer requires standard 110VAC outlet Main Lamps 55 x BRONZING SUN GOLD 200W Face Tanner 5 x 500W with low power option Shoulder Tanner 10 x 26W Ballasts main lamps 200W Body Cooling System Full body cooling directional face vents foot fan Speakers 2 x 80W 2 way speakers plus subwoofer Timer System Digital Max Exposure Time 10 minutes Back up Timer Digital watchdog circuitry Remote Capability FTS Proudly manufactured in the U S A T Max compatible 2
8. acrylic shield replace the face tanner lamps as follows The face tanner assemblies hinge open With a flat bladed screwdriver turn the latch see top right a quarter turn The assembly will open revealing the reflector and lamp holder Remove the two screws right at the end of the face tanner assembly and carefully remove the end bracket and filter glass The lamp can now be exchanged Remove the old lamp by pulling it straight out and discard Install the new lamp using a clean cloth or paper towel to avoid fingerprints on the lamp glass Ensure that the lamp is firmly seated in the lamp holder Note Never take hold of the lamp such that your fingers are in contact with the lamp glass Finger oils will greatly reduce the lamp s operational life Slide the filter glass back in Fasten the end bracket to the assembly Close the hinged assembly and simply press the latch until it clicks to secure LATCH Care and Maintenance Lamp Acrylic Replacement Removing Replacing Face Tanner Lamp in the Rear Lamp Module The face tanner lamp is removed much the same way as in the Canopy However instead of hinging open the face tanner assembly pulls completely out of the module Carefully pull the right side toward you and slide the assembly to the right and out Refer to the previous page for further instructions Removing Replacing Main Lamps After opening the acrylic grasp a lamp at one end and at the m
9. of dust entering the sunbed Pull the small tab at the bottom of the filters to slide them out Each side has two 12 x 18 x 1 furnace filters The air flow arrow on the edge of the filters must point toward the center of the unit when installed Replace the filters whenever they appear dirty or at least every 500 hours of use Setting Operating Parameters The 55755 allows some flexibility in how the unit operates By entering a settings mode on the timer display you may view and or adjust different operating parame ters With the unit sitting idle press and hold the Stop button see page 4 for approxi mately 5 seconds The following screen will appear 7 TOTAL BED HOURS PRESS STOP TO EXIT The first number corresponds to the para meter number followed by the parame ter name The number at the right shows the value in this case the total bed hours Press STOP to exit the settings mode Use the Face Tanner up and down buttons to scroll to the next screen Technical Information The next page explains the five parame ters which may be viewed and or modi fied from the timer display Following that is a list of the parameters recognized by the 55755 timer attached to T Max remote system VI0O c Z9c 26732 01A Technical Information Setting Operating Parameters 7 TOTAL BED HOURS PRESS STOP TO EXIT NEXT V 6 LAMP HOURS PRESS STOP TO EXIT PRESS STAR
10. the tanning unit THIS STANDARD 48 MONTH WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH ARE HEREBY DISCLAIMED No one has the authority to change or modify this Standard 48 Month Warranty in any respect To obtain service under this Standard 48 Month Warranty contact your authorized ETS Distributor or ETS Inc if purchased directly Proof of purchase includ ing serial number is required IN NO EVENT SHALL YOUR DISTRIBUTOR OR THE MANUFACTURER BE LIABLE AT LAW OR IN EQUI TY FOR ANY LOSS LIABILITY DAMAGE OR EXPENSE IN AN AMOUNT IN EXCESS OF THE PURCHASE PRICE RECEIVED OR FOR LOSS OF USE OR PROFITS LOSS OF TIME INCONVENIENCE RENTAL OR SUBSTITUTE PRODUCTS LOSS OF BUSINESS LOSS OF INCOME OR ANY OTHER INCIDENTAL INDI RECT SPECIAL OR CONSEQUENTIAL DAMAGES Some states do not allow the exclusion or limitation of incidental or consequential damages and the above limitation or exclusion will not apply to residents of some states This Standard 48 Month Warranty gives you specific legal rights and you may have other rights which may vary from state to state All warranty service must be performed by an authorized service person labor charges must be authorized by your ETS Distributor prior to the start of repairs and must not exceed the established rates and time allotment policies established by your ETS Dist
11. Les autres types de lunettes pro tectrices peuvent ne pas assurer une protection ad quate Utilis sans lunettes protectrices ce produit peut causer des br lures ou l sions oculaires graves Si vous souffrez d un malaise arr tez l utilisation et consultez un m decin SEULES LES LAMPES SUIVANTES ONT T HOMOLOGU ES POUR CET QUIPEMENT BRONZING SUN GOLD Wolff Mod le BSG 71 T12 200W VS R BI PIN SPEED 525VS R Wolff Mod le SPD71 T12 525VS R 200W Bi Pin Heraeus OH 30 50 ou Heraeus OH 24 50 unit faciale MARQUIS Wolff System amp Mod le CF26W unit en bandouli re D brancher l alimentation lectrique avant de nettoyer l appareil d en faire l entretien ou de changer les lampes TERTE CET QUIPEMENT DOIT TRE MIS LA TERRE Ce produit est conforme aux normes de rendement pour les lampes solaires dans le documents 21 CFR partie US LISTES 1040 20 ANSI UL 482 CAN CSA C22 2 N 224 88465 Installation Pre Installation Planning Before your sunbed is installed you should observe the following considerations DANGER Shock hazard Disconnect power before servicing 55755 requires a dedicated circuit capable of providing either 49 Amp 3 phase service 3 wire plus ground or 85A 1 phase service 2 wire plus ground at 220VAC This unit must be hardwired directly to a junction box on a dedicated circuit We recom mend connection by a professional electrician Co
12. Manager you must wait 10 seconds from the time you start the auto address function before addressing the first bed SunStar amp Bypass plugs or terminator plugs may be needed if the and the sunbed are over 100 feet apart Install the plugs in the open remote port in the sunbed and the T Max If you a T Max amp Manager changing parameter 23 from 0 to 1 will allow the tanning bed to remember how much time was left when power goes out and resume its session after power is restored Consult your T Max amp Manager manual for information on setting parameters 24 Technical Information Power Hook up JUNCTION BOX SINGLE PHASE JUNCTION BOX 3 PHASE GND O 2 aay Ee 0 F o J8 MAIN POWER IN MAIN POWER IN gt E I E 2 ELT i 5 al Sd0 1660 506 g 999 5 pool 000 I m 00 m Lo LojL e x fn 1 z o gt 2 m 3 m I ITI 3 8 g 2 ae ae an I mjo GND 9 2 4 GND 2 5 gt Pie Sie U m S UNIT WIRED 3 IFREWIREDFOR 3 PHASE FROM SINGLE PHASE FACTORY CURRENT 220VAC IS 85 0 291 O w 7 w ES I BENCH TRAY EH F TRAY TO BENCH TRAY EH
13. Setting the address parameter 1 1 Press and hold the STOP button locat ed on the sunbed display until the dis play enters the settings mode approximately five seconds and release The screen will display 7 TOTAL BED HOURS Press the Face Tanner down button until the screen displays 1 BED ADDRESS The num ber to the right is the address which may be anything from 1 to 128 Numbers 252 through 255 are reserved for other functions and should not be used as an address 2 If you are using a T Max or as a master remote the address of the sunbed must be set to 1 If you are using a T Max Manager each sunbed must be assigned a different address Using the Body Fan Control up and down buttons set the value to the appropriate address number 3 Press the stop button to return to the normal display mode VLO TELIT 26732 01 Remote systems using Control Relay Most non T Max remote systems control the sunbed by the use of a relay The relay operates the sunbed by connecting and disconnecting pair of wires leading from the sunbed Refer to the user s manual provided with your remote system to determine if it operates in this way To connect your sunbed to this type of sys tem a remote interface kit is required Contact your place of purchase to obtain the kit Figure 3 details a typical connec tion Follow the instructions provided with the kit and from the remote s manual to make the
14. T TO ZERO CHG HRS V 1 BED ADDRESS PRESS STOP TO EXIT NEXT CHG ADDR V V 36 DEFAULT SESSION VOLUME PRESS STOP TO EXIT NEXT CHG VOL M M 37 DEFAULT IDLE VOLUME PRESS STOP TO EXIT NEXT CHG VOL M MV Guide to the Screens Total Bed Hours Displays total hours the unit has been used This number is not adjustable Lamp Hours Displays the number of hours the lamps have been on This number can be reset to 0 when lamps are changed You may also increase or decrease this number using the Body Fan buttons Bed Address This is the address used in salons with multiple beds and a T Max remote system Use the Body Fan buttons to increase or decrease See Setting the Address Manually in Remote Connections Default Session Volume This is the vol ume the amplifier will automatically increase to when the unit is turned on Adjust with the Body Fan buttons The volume may also be adjusted during the session Default Idle Volume This is the volume the radio will automatically decrease to when the unit shuts off and remains idle Adjust with the Body Fan buttons 20 Technical Information Setting Operating Parameters Below is an extended list of parameters which may be adjusted or viewed using the T Max amp manager Refer to your T Max manual for complete instructions on how to view and adjust parameters Parameter Function Default 1 Unit Address 1 128 1 2 Beep Mode beep halfw
15. WEAR PROTECTIVE EYEWEAR FAILURE TO MAY RESULT IN SEVERE BURNS OR LONGTERM INJURY TO THE EYES Medications or cosmetics may increase your sensitivity to the ultraviolet radiation Consult physician before using sunlamp if you are using medications or have a history of skin problems or believe yourself especially sensitive to sunlight If you do not tan in the sun you are unlikely to tan from the use of this product Children the elderly or fair skinned people who always burn easily and either never tan or tan minimally should not use this equipment To use lie down under canopy and pull down as far as adjustment will allow maintaining at least 6 5 inches 16 5 centimeters between your body and canopy clear plastic panel and side tanner clear plastic panel otherwise overexposure may occur Minimum use distance elsewhere is touching the clear plastic panels Do not use without clear plastic panels in place Untanned persons should not tan on con secutive days during their first week of tanning Never tan more than once a day Tanning normally appears after the first few sessions and maximizes after approximately four weeks Tan once or twice per week thereafter to maintain appearance Persons already having a base tan may begin at advanced levels corresponding to the extent of their base tan RECOMMENDED EXPOSURE TIMES IN MINUTES MAXIMUM EXPOSURE TIME IS 10 MINUTES Level 1 Week 1 Subsequent Skin Type 1st 3rd Sessions Level 2 Level 3 Level 4 Maximum
16. ard Disconnect power before removing any protective covers CAUTION Be careful The edges of the acrylic shield may be sharp A DANGER Unfiltered light from face tanner can cause severe burns Never turn sunbed on while face tanner is disassembled or when glass filters are removed Immediately discontinue use of this equip ment if face tanner glass is broken or any unfiltered light can be seen escaping the face tanner assembly Opening Replacing Acrylic Shields The acrylic shields are secured in place by turn latches Use a 5 16 hex key Allen wrench to turn the latches a quarter turn to release the acrylic The Rear Lamp Module acrylic sits in a channel along the bottom and simply lifts out The Shoulder Tanner acrylic has three turn latches and lifts straight off You may need to lift the Bench acrylic first Opening Replacing Canopy Acrylic Due to the size and weight of the Bench and Canopy acrylics they are not easily removed Instead they employ a hinge across the back edge to allow cleaning and maintenance without removal Using a 5 16 hex key Allen wrench turn the latches along the front edge of the Canopy acrylic one quarter turn and gently rest it on the Bench acrylic Place a towel on the Bench acrylic to avoid scratches Screws secure the Canopy acrylic in the aluminum hinge channel at the rear To remove disconnect the timer display cable from the back of the timer display Loosen the sc
17. ay through session O off 1 0 5 Session Count adjustable 6 Lamp Hours adjustable 7 Bed Hours 8 Manual Sessions counts sessions in stand alone mode 9 Clean Bed Indicator 0 off 1 on 1 14 Unit Beeps Every 5 Minutes 0 off 1 on 0 15 Master Session Count not adjustable 19 Lockout Stand Alone Sessions 0 off 1 on 0 23 Auto Continue see last item in Troubleshooting 1 on 0 31 Beep Frequency 2 255 higher numbers lower frequency 100 32 Beep Volume Offset volume of beeps compared to music 5 0 5 volume level 10 5 volume level 36 Default Audio Volume High during session 37 Default Audio Volume Low unit idle 38 Face Tanner Re light Delay seconds 60 255 Reset Factory Defaults 21 VLO TELIT 26732 01 Problem Sunbed not tanning Lamps fail to light and timer dis play is blank One or more lamps fail to light The face tanners will not come on The canopy will not stay up The canopy will not stay down My canopy opens and closes too fast slamming not enough resis tance Sunbed getting too hot ERROR 92 The bed is off when it should be on Technical Information Troubleshooting Solution Clean sunbed see Thorough Periodic Cleaning Ensure supply voltage is between 208 and 220V AC Replace lamps if lamp hours are greater than 700hrs Replace acrylic Make sure the unit is connected to a power source Check source of AC power Rese
18. ce e Clean both sides of the acrylic shields with a non ammonia disinfectant cleaner e Wipe the reflectors with a clean damp cloth e Reinstall the lamps and acrylic shields Replace air filters inside each bench end cap Replace with a 12 x 18 x 1 fur nace filter Mechanical Inspection Your tanning bed has been built for years of service To ensure trouble free operation throughout its life inspect the unit s mechanical integrity every 400 500 hours of use Inspect the unit s fasteners verifying that all are firmly in place Inspect lift adjustment Adjust for proper lift if needed See Inside the Bench Inspect all power cords and connections Inspect the acrylics Broken cracked or badly scratched acrylics should be immediately replaced Check damper operation The damper limits the canopy s movement speed Replace if canopy raises and lowers too quickly VLO TELIT 26732 01 Care and Maintenance Lamp Acrylic Replacement Lamp and Acrylic Replacement Introduction To be assured of maximum tanning effec tiveness change lamps after approximate ly 500 700 hours of use Lamps used longer than that begin to lose their effec tiveness even though they continue to light To ensure trouble free operation of your sunbed replace the lamp starters whenever the lamps are replaced See Setting Operating Parameters to find out how to monitor lamp hours WARNING Shock haz
19. de the hole on the left of the bench to access the subwoofer There is a power button phase button cut off control and level control see below Consult the subwoofer s user guide for more informa tion Adjust the level to achieve the bass response desired PHASE CUT OFF LEVEL POWER Setup Remote Connections Remote Connections Your sunbed incorporates advanced cir cuitry allowing it to connect and com municate with most remote control sys tems remote system is to be used first determine whether the remote sys tem is a T Max System or a standard remote system operating with a control relay Follow the appropriate instructions on the next few pages for your system type The RJ 22 Remote Ports on the tethered box see right allow connection to the remote system Both remote ports are identical allowing connection of multi ple units in a daisy chain configura tion A Remote Control Bypass plug is already installed in one of the remote ports to bypass the remote functionality otherwise known as stand alone opera tion Your sunbed will not operate without the Remote Control Bypass plug or a remote system connected RJ 22 REMOTE PORTS CAUTION The remote connection is not designed to supply or accept high voltage nor can it provide power to an external timer The sunbed s remote inter face circuitry operates on 5 volts attempting to connect it to any higher voltages will damage the sunbed as
20. e canopy by pushing up on the outer edge of the canopy Do not push up on the acrylic shield The cooling fans run for 10 minutes after the lamps shut off to aid in cooling the sunbed system If using other remotes or no remote sys tem see left N 4 5 face up and lower the canopy toward your body using the canopy handle Maintain at least 6 5 16 5 centime ters between the canopy and your body Put on your safety goggles Assuming the remote system has been set to allow a pre tanning delay time the timer display will read Press start when ready and the remaining delay time Press the START button see pre vious page or wait until the delay time has expired to begin the tanning ses sion The unit will turn on and the timer will begin to count down When the timer reaches 0 00 the lamps turn off If you want to stop your session before time expires press the STOP button Raise the canopy by pushing up on the outer edge of the canopy Do not push up on the acrylic shield The cooling fans run for 10 minutes after the lamps shut off The timer will indicate a reminder to clean the sunbed After the sunbed is cleaned press the START button and the display will return to the welcome screen VLO TELIT 26732 01A Setu Stereo Installation The 88755 accepts an input from a stereo source The unit contains speakers inside the Shoulder Tanner a subwoofer in the bench and a
21. iddle and turn the lamp one quarter turn Gently remove the lamp from its holders Reinstall the lamp by inserting the pins located on the ends of the lamp into the slots on top of the lamp holders and turn the lamp a quarter turn It should click in place Recommended Replacement Lamps Removing Replacing Mood Lamp Inside the front edge of the canopy is a lamp that remains on at all times Remove and replace it exactly like one of the main fluorescent tube lamps The red sleeve simply slides on and off Replace with a Sylvania F72T12 D835 HO lamp Removing Replacing Shoulder Tanner Lamps After removing the Shoulder Tanner acrylic grasp a lamp by the white base never by the lamp glass and pull straight up Replace the lamp by lining up the base pins with the socket and pressing firmly in place Recommended Replacement Acrylics Acrylics vary greatly over time in their ability to effectively transmit UV light Acrylics sold by ETS have been life tested to ensure proper transmission throughout their useful life We recommend using the lamps specified below Use of uncertified lamps is a viola tion of Federal regulations and will void your warranty BRONZING SUN GOLD Wolff Model BSG 71 T12 200W VS R SPEED 525VS R Wolff Model SPD71 T12 525VS R 200W Bi Pin Heraeus 30 50 or Heraeus 24 50 facial unit MARQUIS Wolff System Model CF26W shoulder unit 15 VI0O c Z9c 26732 01A Care a
22. ive Les autres parties du corps peuvent toucher les panneaux de plastique transparents N utilisez pas la lampe sans les panneaux de plastique transparents La premi re semaine de bron zage les personnes qui n ont pas un h le initial ne doivent pas se faire bronzer tous les jours Ne vous faites jamais bronzer plus d une fois par jour Le bronzage commence normalement apparaitre apr s les premi res s ances il atteint son apog e au bout d environ quatre semaines Les personnes qui ont d j un teint h l peuvent commencer des niveaux plus lev s selon l importance de leur h le initial TEMPS D EXPOSITION RECOMMAND EN MINUTES LE TEMPS D EXPOSITION MAXIMAL EST DE 10 MINUTES lev 1 Semaine 1 A D Sem suivantes Type de peau ere e Elev 2 Elev 3 Elev 4 Temps maximal Peau sensible br le facilement et ne bronze pas NON RECOMMAND l Peau claire br le facilement et bronze tr s peu 2 4 6 8 10 Peau normale br le et bronze de fa on mod r e 3 5 7 10 10 IV Peau fonc e br le tr s peu bronze plus facilement que la moyenne 4 6 8 10 10 AVERTISSEMENT Lisez le livret d instructions avant d utiliser cette lampe solaire Les autres personnes pr sentes dans la pi ce doivent aussi porter des lunettes protectrices lorsque les lampes sont allum es Coquilles de protection pour les yeux recommand es Les coquilles de protection fournies ou l quivalent tel que le stipule le document 21 CFR 1040 20
23. n integrated amplifier in the bench ballast drawer Volume control is conveniently located on the timer keypad see Using Your Sunbed Locate the small black box tethered to the back of the unit with cables see right There are three sets of inputs RJ 22 remote ports explained on the next page speaker level input spring connectors and line level RCA input jacks Connect the output from a stereo source receiver CD player boom box etc to either of the last two inputs Whenever possible use the RCA input jacks as this will eliminate problems with volume Once a source is connected apply power to the sunbed do not turn the sunbed on If using the RCA jacks setup is complete If using the speaker terminals adjust the vol ume on the source unit Once a pleasant volume level is reached use only the timer keypad to adjust it in the future Two default volume levels one lower level for when the unit is idle and a slightly higher level when the unit is turned on keep the music audi ble yet not too loud for other tanners See Setting Operating Parameters to change the RCA INPUT JACKS SPEAKER LEVEL INPUTS defaults Music may play continuously through the sunbed during the day The sunbed controls only the volume so if the source is a CD player or tape etc you must control the music at the source unit To adjust the subwoofer output remove the Front Access Panel see Inside the Bench and reach insi
24. nd Maintenance Lamp and Acrylic Replacement Replacing Decorative Lamps 1 Inside the front of the are three sets of fluorescent lamps six lamps total which illuminate the decorative windows To access these lamps you must remove 9 the front canopy cover Follow these SREWIN directions carefully HANDLE CHANNEL Lift the canopy Along the front edge of the canopy acrylic runs the handle channel Remove the five screws in this channel and remove the entire channel piece see above right Pull the rear access panel back a few inches to expose the service lock holes see right Lower the canopy and insert two long metal pins such as screwdrivers into the holes to keep the canopy down after the weight of the cover is removed The front half of the cover will now slide down see below Continued on next page Care and Maintenance Lamp Acrylic Replacement The front cover is secured by two springs Unhook each spring and hook it to the hole in the upper cover to avoid losing the spring under the upper cover If that hap pens the upper cover simply lifts off after removing the five screws along its back edge Replace the lamps by twisting a quarter turn and pulling it gently from its lamp holders It is recommended to replace all six lamps and their starters at the same time even if only one is burned out to avoid unnecessary handling of the canopy cover Replace with standa
25. necessary connections CAUTION The remote connection is not designed to supply or accept high voltage nor can it provide power to an external timer The sunbed s remote inter face circuitry operates on 5 volts attempting to connect it to any higher voltages will damage the sunbed as well as void your warranty Setup Remote Connections Non T Max Remote System using control relay Remote Interface Kit figure 3 Cleaning After Use Clean and disinfect your tanning bed s bench and canopy after each use Use non abrasive disinfectant cleaner that does not contain ammonia or ammonia deriva tives Ammonia may damage the acrylic shield Spray the acrylic lightly with disin fectant and wipe dry with clean soft cloth We recommend SunQuest disinfectant and SunQuest acrylic cleaner Thorough Periodic Cleaning Introduction The cooling fans draw air through the bed and over time will cause a dust buildup on the lamps and reflectors This will reduce the tanning effectiveness of the bed When a dust buildup is observed it is necessary to thoroughly clean the inside of the bench and canopy WARNING Shock hazard Disconnect power before removing any protective covers e Open the acrylic shields and remove lamps as described in Lamp and Acrylic Replacement e With a soft cloth wipe the entire length of each lamp to remove any film buildup 11 Care and Maintenan
26. nnects the chain without a sunbed and interrupt the rest of the units VLO TELIT 26732 01 Problem Timer display continues to show 1 the welcome screen after 2 timer button is pressed bed is connected to a remote system but am having trouble accessing parameter 1 My bed connected to T Max Manager did not display a delay time but does indicate the welcome screen a tanning time and the lamps have come on a tanning time but the lamps have not come on When auto addressing the first bed does not register an address When using a T Max 1A sunbed won t function properly My salon suffers frequent short power outages and clients com plain about losing session time Technical Information Troubleshooting Solution T Max Manager remote system has not yet been set Sunbed address is not set correctly see Remote Connections You have probably attempted to connect your sunbed to the remote system already Disconnect the remote plug s from the ports on the input box wait 90 seconds and try again Remote device has not been set The sunbed has not been connected to the remote system see Remote Connections Delay time of T Max amp Manager has not been set Delay time has expired and session has begun Auto start function of T Max amp Manager has been turned off Press the timer button to turn on lamps When using the auto address feature of the T Max
27. nsult local and or national codes for proper circuit breaker and wire gauge The subwoofer in the bench requires standard 110VAC outlet near the back of the unit e IMPORTANT Operating voltage must be below 230V AC or may require a Buck Booster WARNING Always wear protective eyewear when unit is on Failure to may result in severe burns or longterm injury to the eyes A CAUTION Use of a voltage source above 230V AC with unit running may prevent proper operation of the sunbed and could cause damage and void the warranty A CAUTION Air from the room is used to cool the sunbed Maximum ambient room temperature should be 80 F Place your sunbed no closer than 6 from side walls May be posi tioned against back wall Make sure nothing obstructs the airflow into or out of the fan openings A poorly ventilated room may cause the unit to become hot and cause discom fort to the user VLO TELIT 26732 01 Unpacking and Inspection Your sunbed arrives fully assembled Some disassembly may be necessary to transport the unit into your salon Due to the size and weight of the unit we recom mend installation by professional techni cians After unpacking inspect the unit to make sure it is free from any visible damage Report the extent of any damage to the transportation company Record the serial number located on the rear of the unit in the area provided below This information will be
28. or obstructions 3 If problem persists contact servicer forgot what address set my By holding the body fan down button for 3 seconds the timer sunbed to parameter 1 display will briefly display four numbers the display version the installed timer software version the bed address and then a factory set timer code Timer display changes to indicate 1 Bypass plug is not installed see Remote Connections a tanning time after the timer 2 non SunStar amp bypass has been used See Remote ton is pressed but lamps do not Connections come on 3 If remote is being used other than T Max amp Manager the external timer may not be activated 4 Remote wiring is incorrect see the instructions provided with the remote interface kit My bed is connected to the T The auto start feature of the remote system is disabled see the Manager remote system and instructions provided with your remote system when the delay time has expired the timer display starts counting down but the bed lights do not come on My bed won t work with the 1 The sunbed must first be set to a unique address see Remote Max Manager remote system Connections 2 The bypass or terminator plug may be installed in the series in an inappropriate location Plug the bypass plug only into the bed at the end of the series frequently disconnect my A T Max Inline 4 Pin Connector is available from ETS Inc sunbeds from the T Max chain which co
29. rd 24 T8 17W lamps Reinstall the cover by reversing the previ ous directions WARNING Shock hazard Disconnect power before removing any protective covers SPRING HOOKED TO UPPER COVER VLO TELIT 26732 01A Inside the Bench The contoured access panel on the front of the bench unlatches and pulls off to reveal four important components of the unit the bench ballast drawer with timer and amplifier components the canopy ballast drawer the lift adjustment mechanism and the air filters The ballast drawers require no routine maintenance Lift the bench acrylic and turn the latches along the top of the access panel to remove Lift Adjustment Your sunbed uses a smooth gliding spring lift system to raise the canopy Occasionally this lift system may need to be adjusted slightly Use a wrench to turn the hex shaped Lift Adjustment lugs shown below clockwise for more lift and counterclockwise for less When adjusted properly the canopy should raise easily as well as rest fully closed Always adjust both lugs equally SUBWOOFER ACCESS LIFT ADJUSTMENT LUGS Care and Maintenance Inside the Bench WARNING Shock hazard Disconnect power before removing any protective covers Air Filters On both sides of the bench are large blowers which provide the cooling air for the unit and the body cooling vents Inside the bench endcaps are air filters to minimize the amount
30. required whenever you call Customer Service Record this information for ease of service Date of purchase Serial number Installation Unpacking and Inspection Package Contents In addition to a pillow and a few items left over from the assembly the following items are provided for use and maintenance Safety Goggles Quantity 1 5 16 Hex key for acrylic latches Quantity 1 Touch up Paint in Red and Silver bottle may vary Operation Before You Tan Before using your sunbed please note the following important precautions e Your skin should be free of cosmetics oils or other body lotions prior to tan ning except for those specifically made for use with tanning devices However do not remove natural body oils by bathing or showering immedi ately before tanning e Your hair should be free of gels mousses sprays or other hair products prior to tanning These products can cause damage to the sunbed acrylic As an alternative a shower cap or towel can be worn to keep treated hair away from the sunbed surfaces This unit intended for individual use Only one pair of eyewear is included RECOMMENDED EXPOSURE TIMES IN MINUTES Level 1 Week 1 1st 3rd Sessions Skin Type Sensitive Skin Burns easily and severely and does not tan l Light Burns easily and severely and tans minimally 2 4 6 8 10 3 5 Burns moderately and tans average Burns minimally tans easily and above average
31. rews along the inside of the hinge channel The acrylic will then slide out of the channel Replace it by setting it in the hinge channel and tightening the screws Connect the timer display cable 12 Care and Maintenance Lamp Acrylic Replacement Opening Replacing Bench Acrylic The Bench acrylic also does not need to be removed to perform normal mainte nance such as cleaning and replacing lamps Turn the quarter turn latches on either side of the acrylic and lift the front edge Two gas springs hold it open A secondary acrylic rests below the main acrylic Simply lift the secondary acrylic out to access the lamps To remove the Bench acrylic lift the acrylic so the gas springs are fully extend ed Each gas spring is held to the acrylic bracket with a locking pin Unclip the pin and slide it out to disconnect the spring from the acrylic see top right Inside the Bench at the back corners of the acrylic are two keeper brackets see bottom right Swing the bracket up to free the Bench acrylic hinge Raise the acrylic and lift it along with the hinge channel from the Bench Replace the acrylic by setting the hinge channel in its slot at the rear of the Bench Swing the keeper brackets down and reconnect the gas springs KEEPER BRACKET VI0O C Z9C 26732 01A Care and Maintenance Lamp and Acrylic Replacement Removing Replacing Face Tanner Lamps on the Canopy After opening the Canopy
32. ributor If your tanning unit must be returned for service all freight charges shall be at your expense Contact your ETS Distributor for the authorized Service Center nearest you This war ranty is serial number specific and only applies to tanning units purchased through an authorized ETS Distributor This warranty is extended to the individual or legal entity whose name appears on the original sales document and may not be transferred to any other individual or legal entity This warranty is void if the tanning unit is modified in any manner from its original design To obtain warranty service contact your place of purchase Proof of purchase including serial num ber is required for verification Contact ETS Inc only if you purchased your equipment directly ETS Inc 7445 Company Drive Indianapolis IN 46237 9296 1 1 800 449 3605 Canada call 1 800 661 6292 or 519 421 1212 VLO TELIT 26732 01 e Welcome Congratulations on your purchase of this technologically advanced sun tanning unit It has been designed to provide years of dependable service for you Please read all the instructions in this booklet before using the unit Always be sure to observe all safety precautions Contents Safety Information iii Installation 1 Pre Installation Planning 1 Unpacking and Inspection
33. t circuit breaker or replace fuse Check that lamp is installed correctly Switch unlit lamp with a lamp that lights if new lamp lights and old lamp still does not replace old lamp Face tanner operation is initially delayed by a few seconds Face tanners will not relight for 60 seconds after being shut off See Setting Parameters for more information Replace face tanner lamp see Removing Replacing Face Tanner Lamps Your sunbed uses a smooth gliding spring lift system to raise the canopy This lift system may need to be adjusted slightly from time to time See nside the Bench for proper adjustment proce dures The canopy should raise easily as well as rest fully closed Your sunbed utilizes a damper which limits the canopy s movement speed This also serves as a safety device in case of spring lift failure as the canopy will not crash down Replace the damper on back of unit Turn body fan on HI Ambient temperature of salon room must be below 80 at all times Check air filters Change if dirty Input voltage with unit running must be less than 220VAC Current sensor indicating unit is off when it should be on Contact servicer Technical Information Troubleshooting Problem Solution ERROR 93 The bed is on when it Current sensor indicating unit is on when it should be off should be off Contact servicer ERROR 98 Bed temperature 1 Allow the unit to cool exceeded 2 Check all fan openings and air filters f
34. uestions 417 338 5101 NOTE A T Max can be substituted for the 3A in figure 1 figure 1 system noting figure 1 If you have an older T Max amp Manager that does not support auto addressing set the address of each sunbed manually as described on the next pe amp page You can place your sunbed at any location in the series Q X S Non T Max incorporated units Setup Remote Connections T Max and 3A Remote Systems In single sunbed installations the 1A and 3A can offer the same control as the T Max amp Manager eliminating the need for a Manager If you re using a 1A in this manner it must have a chip labelled master installed on its circuit board The 3A may be used as a master with no modification After you have set the T Max amp 14 3A s address to 0 refer to your T Max amp user s guide and the sunbed s address to 1 see right simply connect the RJ 22 modular cables described in the T Max amp user s guide directly into either port in the tethered box and either port on the back of the T Max 1A or 3A See figure 2 figure 2 NOTE T Max amp 1A with a master chip can be substituted for a 3A in figure 2 Setting the address manually Before connecting your sunbed to the T Max Manager or or the address of your sunbed must first be set Set the id manually as described below
35. well as void your warranty VLO TELIT 26732 01 T Max Products The T Max remote systems offer the ulti mate in sunbed control while allowing the tanner easy straightforward operation Your sunbed is configured to directly con nect to this system The circuitry inside your sunbed eliminates the need for the T Max or when connecting to the T Max Manager series Your sunbed sup ports the auto addressing feature of the lat est T Max amp Manager models and many parameters See Setting Operating Parameters and your T Max manual for descriptions of these parameters and how they function T Max Manager Remote System This system is ideal for multiple sunbed installations Simply connect the RJ 22 modular cable s described in the T Max Manager manual into the remote port s located on the tethered input box and follow the instruc tions that came with your remote T Max Manager Setup Remote Connections Auto Addressing with T Max Your T Max amp Manager manual will explain how to get into auto address mode Once auto address has been acti vated the bed display will show Auto address active press start key to address Wait 10 seconds for the system to com municate properly and press the START button The display will indicate waiting for address and return to the welcome screen when it has accepted the address Go straight to the source with all your T Max brand remote q
Download Pdf Manuals
Related Search