Home

Letter - United Process Controls

image

Contents

1. 4 an C 4 Copper Tube 1 8 NPT Port 1 8 NPT Tee is L y Compression V x Fitting 1 8 Plug 4 8 Isolation Valve File Manu016 Carburetor User Manual 7 Wiring Guidelines Your company may have guidelines for wiring installation If so you should check those before you begin the installation Here are some general things to consider e Use the shortest wiring route whenever possible e Route the wiring through an approved cable housing to minimize the risk of accidental damage Check local and national codes to choose the correct method for your application CAUTION To reduce the risk of electrical shock and also to prevent A damage to the Automatic Lubricator It is advised to turn off the supply power to the Automatic Lubricator before connecting or disconnecting any wires Wiring The unit should be wired such that power is supplied to it only when the compressor is running It is very important that power to the Automatic Lubricator is OFF when the compressor is not running The recommended method for wiring the unit is to connect power through the normally open contacts of the motor starter of the compressor s drive motor See Figure 4 for wiring excessive oil may build up in the compressor causing damage to the compressor and or any components located downstream of the compressor 1 WARNING If power is supplied to the unit while the compressor is off WAR
2. 50 60 Hz Power Consumption 0 2 amps File Manu016 Carburetor User Manual 6 INSTALLATION Mounting If the Automatic Lubricator was purchased with a compressor it will already be mounted otherwise mounting will be required if the unit was purchased separately The Automatic Lubricator can be mounted onto the side of the compressor with the include mounting bracket as shown in Figure 2 or anywhere within 2 3ft of the compressor The Automatic Lubricator is a gravity feed type oiler which requires the oiler to be mounted higher than the compressor in order to function properly Plumbing tem Mounting Bolts The Automatic Lubricator requires only two TS Mounting Bracket plumbing connections unless your oiler was c ee preinstalled by Waukee The first connection is 1 1 4 Oil Feed Tube the oil feed tube Refer to Figure 2 Connect a Figure 2 copper tube from the solenoid valve to the 1 8 NPT port located on top of the compressor The oil feed tubing should be kept as short and vertical as possible to provide the best performance The second connection is the pressurized feedback Refer to Figure 3 Connect a 74 copper tube from the top of the oiler to the 1 8 NPT port located on the side of the compressor Compression Fitting _ Figure 3 Ys Copper Tube
3. AUKEE any representations beyond those contained in WAUKEE literature and documents or to assume for WAUKEE any obligations or duties not contained in this Warranty and Warranty Policy WAUKEE reserves the right to make design and other changes modifications or improvements to its products services literature or systems without any obligation to furnish or install same on any previously sold or delivered products or systems Carburetor User Manual 11 LIMITATION OF LIABILITY It is expressly agreed that the liability of WAUKEE is limited and WAUKEE does not function as an insurer The purchaser and or user agree that WAUKEE is not liable for loss harm or damage due directly or indirectly to any occurrence or consequences therefrom If WAUKEE should be found liable to anyone on any theory except any express warranty where the remedy is set forth in Section 2 of this Warranty and Warranty Policy for loss harm or damage the liability of WAUKEE shall be limited to the lesser of the actual loss harm or damage or the purchase price of the involved WAUKEE equipment or service when sold or when service performed by WAUKEE to its customer This liability is exclusive and regardless of cause or origin resulting directly or indirectly to any person or property from 1 The performance or nonperformance of any obligations set forth in this Warranty and Warranty Policy 2 Any agreement including specifications between WAUKEE and the c
4. NING The Unit is designed for use with 115VAC Single phase 50 60Hz power ONLY Connection of any other power type may damage the unit and may subject personnel to shock or injury Figure 4 File Manu016 Carburetor User Manual 8 OPERATION Filling the Oil Reservoir Before opening the oil fill port turn off the isolation valve on the Figure 5 feedback line See Figure 3 Remove the Oil fill plug See Figure Oil Fill 5 and fill the oil reservoir with Waukee Compressor Oil Port Part No s COIL 1 pint COIL 2 quart or COIL 3 gallon Once reservoir is full replace the oil fill plug and open the isolation valve WARNING Lack of or improper lubricating oil may cause damage to the compressor Use Waukee Compressor Oil ONLY CAUTION Before removing oil fill plug turn isolation valve OFF Failure to turn isolation valve OFF will result in compressed gas leaking from the oiler and may cause a hazardous situation Gas leaking from oiler may be flammable gt e oil and replacing the oil fill plug If isolation valve is left closed oiler will WARNING Make sure isolation valve is open after filling oil reservoir with not be able to drop oil and cause premature failure of the vanes Starting the Compressor Every time the compressor is started the Green Power On light on the Automatic Lubricator should
5. WAU KE E WWW GROUP UPC COM ENGINEERING company inc Waukee AutoLube User Manual D a B LURR VER UN LUSRIGATING AUTOMATIC J LUBRICATOR e 10 VOLTS GSO CYCLE Jinited AFFILIATED MEMBERS PROCESS CONTROLS Furnace Control Corp Marathon Monitors Inc Process Electronic Waukee Engineering Co Manual 016 Initial Release 4 24 2008 Rev No C Date 12 22 10 For assistance please contact Waukee Engineering Co Inc TEL 1 414 462 8200 FAX 1 414 462 7022 sales waukeemeters com www waukeemeters com File Manu016 Carburetor User Manual 2 X WARNING Thank you for purchasing equipment from Waukee Engineering a member of United Process Controls We want your new equipment to operate safely Anyone who uses this equipment should read this publication and any other relevant publications before installing or operating the equipment To minimize the risk of potential safety problems you should follow all applicable local and national codes that regulate the installation and operation of your equipment These codes vary from area to area and usually change with time It is your responsibility to determine which codes should be followed and to verify that the equipment installation and operation is in compliance with the latest version of these codes At a minimum you should follow all applicable sections of the National Fire Code National Electrical Code and codes o
6. be ON and remain on until the compressor is stopped Also the Amber Lubricating light will illuminate for 4 seconds During this 4 second time oil should be seen dropping in the sight glass The Automatic Lubricator is a ON OFF cycle timer it will start with a 4sec ON time and after the ON cycle completes it will remain OFF for a period of 1Hr and will continue to cycle until power is removed Adjusting the Oil Flow Rate The solenoid valve is factory set to provide the proper number of oil drops during the ON period of 4 seconds To verify or adjust the oil flow rate depress and hold the Manual Lubrication Button located on the left side of the Automatic Lubricator and adjust the Oil Control Valve to obtain the proper number of oil drops within a 15 second time interval The number of drops required during the 15 second interval is displayed on the nameplate attached to the front of the Automatic Lubricator s enclosure If the nameplate is unreadable or the Automatic Lubricator will be used on a different compressor that what it was ordered for then refer to Table 1 on the following page to determine the proper amount of drops for your compressor File Manu016 Carburetor User Manual 9 TABLE 1 OIL RATE CHART IN DROPS OF OIL PER 15 SECOND PERIOD Number of Drops Required over a 15 second period Flow Output of Compressor Output Pressure Output Pre
7. brands to the heat treating industry including Waukee Engineering Furnace Control Marathon Monitors and Process Electronic We provide prime control solutions through our worldwide sales and services network with easy to access local support WAUKEE ENGINEERING COMPANY INC A member of United Process Controls 5600 West Florist Avenue Milwaukee WI 53218 U S A Phone 1 414 462 8200 Fax 1 414 462 7022 e mail sales waukeemeters com a 4 v d fite QV x Td QUE Y t United PROCESS CONTROLS f WN ES
8. e 11 Performance activity 12 Any other pertinent information If a sketch would help explain the difficulty please include one WARRANTY FIELD SERVICE If warranty Field Service at the request of the purchaser or user is rendered and the difficulty is found not to be with WAUKEE s product the purchaser shall pay the time and expense at the prevailing rate at the time of the service of WAUKEE s field representative s Charges for service labor and other expenses that have been incurred by the purchaser its customer or agent without written approval of WAUKEE will not be accepted The OEM or other reseller is responsible for transmitting installation and operating instructions THE MANUAL or other service literature supplied by WAUKEE with the equip Carburetor User Manual 12 APPENDIX A DRAWINGS File Manu016 Z i ER YELLOW OWER ON LUBRICATIN a AUT ATI L ICAT 110 VOLTS LE ODEL 0999 ATENT NO THIS IS A NEMA 12 ENCLOSURE AND IS NOT CLASSIFIED AS A EXPLOSION PROOF ENCLOSURE 2NUT FOR CLASS 1 INSTALLATIONS PLEASE CALL WAUKEE ENGINEERIN D FOR FURTHER INFORMATION 414 462 8200 pecca MES Carburetor User Manual 13 Reach us at www group upc com United Process Controls brings together leading
9. e e mail or contact us by phone Conventions Used When you see the exclamation point icon in the left hand margin the A paragraph to its immediate right will be a warning This information could prevent injury loss of property or even death in extreme cases Any warning in this manual should be regarded as critical information that should be read in its entirety The word WARNING or CAUTION in boldface will mark the beginning of the text File Manu016 Carburetor User Manual 5 The Waukee Automatic Lubricator controls the amount of lubricating oil supplied to the compressor The Automatic Lubricator is comprised of an electronic timer an oil reservoir and a solenoid valve The unit is designed to automatically lubricate Waukee compressors that require lubrication This unit insures that the compressor is properly lubricated to provide maximum life for the compressor vanes Oil Fill Port cu Oil Reservoir Yellow Lamp N Lubricating Green Lamp Power ON Oil Control Valve gt GREED ELLIW 5 de E OWER ON LUBRICATINC CAUTIBN A Eee TU Solenoid Valve Manual Lubrication Button AUTOMATI 2 LUBRICATO secco VR SL Oil Feed Sight TUIS Map n Window c NOT FOR CLASS 1 INSTALLATION LEASE CALL WAUKEE ENGINEERING D Figure 1 SPECIFICATIONS Voltage 115VAC
10. ea AA aE aer NAERA r EEEa aata cote reset e RA aT 7 araa p E 8 APPENDIX AC DRAWINGS idein aac erii pera tete io ded don per nono dci Read e or ear 11 File Manu016 Carburetor User Manual 4 INTRODUCTION The Purpose of this Manual Thank You for Purchasing a Waukee Automatic Lubricator This Manual shows you how to install and maintain Waukee s Automatic Lubricator This manual contains important information and should be read and understood by all individuals who install use or service this equipment Supplemental Manuals The Waukee Compressor Mixor Manual 3254 manual contains technical information as well as precautions regarding use of Waukee s Automatic Lubricator with a Waukee Compressor Technical Support We strive to make our manuals the best in the industry We rely on your feedback to let us know if we are reaching our goal If you cannot find the solution to your particular application or if for any reason you need technical assistance please call us at 414 462 8200 Our technical support group will work with you to answer your questions They are available Monday through Friday from 8 00 A M to 4 30 P M Central Standard Time We also encourage you to visit our web site where you can find technical and non technical information about our products and company http www waukeemeters com http www group upc com If you have a comment question or suggestion about any of our products services or manuals pleas
11. f the National Electrical Manufacture s Association NEMA There may be local regulatory or government offices that can also help determine which codes and standards are necessary for safe installation and operation Equipment damage or serious injury to personnel can result from failure to follow all applicable codes and standards We do not guarantee the products described in this publication are suitable for your particular application nor do we assume any responsibility for you product design installation or operation If you have any questions concerning the installation or operation of this equipment or if you need additional information please call us at 414 462 8200 A WARNING Read this manual thoroughly before using Autolube File Manu016 Carburetor User Manual 3 TABLE OF CONTENTS TRODUG TON t EE 3 DESCRIPTION dcctizexnsiraliskuxt hasce steraghoklota femrepu oeil evrgaz ek eid plato ride na blan iege da poner b la Corda ue 4 xeu ac EE 4 INSTALLATION peers EP EE 5 MOUNTING ceti Sh ceed et eatin Past hd eeni La M is lain See cans seine Sites UP d noc eo hace tenes sR aes ted 5 pU cm T 5 WIRING GUIDELINES petto etes ipto beris apte deetttes note EE a R AERA Desc festi das 6 cs ES 6 e dz ripe e 7 BILLING THE OIL RESERVOIR rires tuns Oi e iaa a iscestte Ghetto e e f os aa E E cete ufo 7 STARTING THE COMPRESSOR M 7 ADJUSTING THE QIL FLOW RATE e i redit aea Aa
12. fied in the applicable quotation purchase order acknowledgment marketing literature nameplate s specification sheet or the Installation Operation Inspection and Maintenance Manual THE MANUAL 2 Using only clean liquids or gases only liquids in liquid Flo Meters and only gases in gas Flo Meters air and fuel gases used in mixing equipment to be clean and free of solids all as further explained in THE MANUAL and 3 Installation operation inspection and maintenance in compliance with THE MANUAL and 4 The WAUKEE products being used only in a Ambient environments lower than 132 Fahrenheit 54 Celsius unless specifically designed and so labeled by WAUKEE for higher temperatures and b Non corrosive environments and c Completely protected from moisture rain snow or other outside environments and d Not to be used below 32 Fahrenheit 0 Celsius unless special precautions are taken for low temperature conditions as shown in THE MANUAL 5 Being used only for applications permitted by THE MANUAL or other WAUKEE literature or special applications approved in a separate written authorization by WAUKEE WARRANTY EXCEPTIONS This Warranty does not apply to damage caused by any or all of the following circumstances or conditions 1 Freight damage 2 Parts accessories materials or components not obtained from nor approved in writing by WAUKEE 3 Any consequential or incidental damages including but
13. not limited to loss of use loss of profits loss of sales increased costs arising from the use of any product File Manu016 system or other goods or services manufactured sold or provided by WAUKEE 4 Misapplication misuse and failure to follow THE MANUAL or other literature instructions or bulletins including drawings published or distributed prior to THE MANUAL The exclusive remedy under this Warranty or any other express warranty is the repair or replacement without charge for labor and materials of any WAUKEE parts found upon examination by WAUKEE to have been defective Since certain WAUKEE equipment is heavy bulky and not deliverable by U S mail or other parcel service WAUKEE equipment may be returned only upon written consent of WAUKEE and then only to the location designated by WAUKEE Generally such consent will be given only upon the condition that the customer assume and prepay all carrier charges and responsibility for damage in transit Purchasers of WAUKEE products equipment goods or services waive subrogation on all items covered under their own or any other insurance DISCLAIMER THIS WARRANTY IS EXCLUSIVE WAUKEE EXPRESSLY DISCLAIMS ANY AND ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY PURPOSE No person including any dealer seller or other representative of WAUKEE is authorized to make on behalf of W
14. ssure Output Pressure 1psig 6 9kPa 2psig 13 8kPa 30519 20 7kPa 200CFH 5 6M3H 3 4 5 400CFH 11 3M3H 3 4 5 600CFH 17 0M3H 3 4 5 750CFH 21 2M3H 4 5 6 1000CFH 28 3M3H 4 5 6 1250CFH 35 4M3H 4 5 6 1500CFH 42 5M3H 4 5 6 2000CFH 56 6M3H 6 9 10 3000CFH 84 9M3H 6 9 10 4000CFH 113 3M3H 6 9 10 5000CFH 141 6M3H 7 10 12 6000CFH 169 9M3H 7 10 12 7000CFH 198 2M3H 7 10 12 8000CFH 226 5M3H 7 10 12 PARTS LIST TABLE 2 PARTS LIST Description Part Number Amber Indicator Lamp 1 2140 Green Indicator Lamp 1 2139 Timer Board 1 2268 Solenoid Valve Assembly 1 3119 Manual Lubrication Button 1 3120 Support Bracket for A B and C Compressors 3 867 Support Bracket for D H J and E Compressors 3 868 Support Bracket for F G and N Compressors 2 572 Support Bracket for R S U and W Compressors 2 571 Compressor Oil pint COIL 1 Compressor Oil quart COIL 2 Compressor Oil gallon COIL 3 File Manu016 Carburetor User Manual 10 EXPRESS WARRANTY ON WAUKEE EQUIPMENT WAUKEE warrants its products for a period of one 1 year from date of shipment from WAUKEE to the original purchaser to be free from defects in material and workmanship under normal recommended use service inspection and maintenance Normal recommended use service inspection and maintenance mean 1 Not to be used in excess of nor below the rated capacity pressures and temperature ranges speci
15. ustomer 3 Negligence active passive or otherwise of WAUKEE or any of its agents or employees 4 Breach of any judicially imposed warranty or convenant of workmanship durability or performance and 5 Misrepresentation under the Restatement common law or otherwise and or strict liability involvement 6 Liability for fraud in the inducement INFORMATION NECESSARY TO OBTAIN TECHNICAL ASSISTANCE For WAUKEE to appropriately respond to a request for assistance or evaluation of customer or user operating difficulty Please provide at a minimum the following information 1 Serial number and type or model of meter compressor or other equipment and all other data shown on the nameplate and on the specific component which appears to be involved in the difficulty File Manu016 2 The date and from whom you purchased your WAUKEE equipment and your purchase order number 3 State your difficulty being sure to mention at least the following 4 Application 5 Input pressure where Flo Meters or compressors are involved 6 Condition of filters strainers or screens upstream or downstream of the WAUKEE equipment 7 Gas or liquid temperatures and other ambient conditions at the time of the difficulty 8 Type of lubrication being used if any give specifics 9 Any other relevant pressures including gauge readings both upstream and downstream of the WAUKEE equipment 10 All electrical information availabl

Download Pdf Manuals

image

Related Search

Related Contents

Blanco BDW 209 User's Manual  LE STAGE DE PREMIERE ANNEE  H1N1 Vaccination Program FAQs PROVIDER SITE  TL-LD610-R 取扱説明書  Samsung MM-ZL7 User Manual  en fractionné  FE-5020/X-935 FE-4010/X-930  Headline: Formatvorlage „eo_pm_head“  DL4500 User Manual - Equustek offers connectivity from DH+ to  安全性データシート  

Copyright © All rights reserved.
Failed to retrieve file