Blanco BDW 209 User's Manual
Contents
1. Arrange the spoons dessert spoons knives and other small items of cutlery in the racks on both sides of the cutlery basket 8 The upper basket The upper basket is designed for plates dessert plates saucers dinner plates of up to 24 cm in diameter salad bowls cups and glasses Glasses with long stems can be placed upside down in the raised cup racks Light items plastic bowls etc should be loaded in the upper basket and arranged so they do not move Before closing the door ensure that the spray arms can rotate freely Adjusting the height of the upper basket If washing very large plates over 27 cm and up to 31 cm in diameter you can load them in the lower basket after moving the upper basket Never lift or lower the basket on one side only To move to the higher position proceed as follows 1 Pull out the basket until it stops 2 Carefully lift both sides upwards until the mechanism is engaged and the basket is stable When the top basket is in the higher position it will only take plates up to 20 cm in diameter and you will not be able to use the raised cup racks To lower the basket to the original position 1 Pull out the basket until it stops 2 Carefully lift both sides upwards and then allow the mechanism to drop back down slowly keeping hold of it When loading the dishes ensure that you do not cover the water inlet funnel in the middle of th2. The On Off indicator light will come on and the machine will start If you wish to interrupt the wash programme at any time press the button again At the end of the washing programme At the end of the washing programme the machine stops automatically The On Off indicator light remains on until the On Off button is depressed Switch off the dishwasher Switch off the dishwasher by pressing the On Off button and open the door When the wash programme has finished it is recommended that the dishwasher is unplugged and the water tap turned off In general it is not advisable to open the door while the machine is working if the door is opened however a safety device ensures that the machine stops Caution Do not open the door during the hot phase this may cause hot water escape Care must be taken if the door is opened during the hot phase or immediately after a programme has finished as steam may escape POS20GB Maintenance and cleaning Internal cleaning Ensure that the seals around the door the detergent and rinse aid dispensers are cleaned regularly with a damp cloth We recommend you carry out a maintenance wash every three months by running a 65 programme without dishes using detergent Cleaning the central filters after each wash Inspect the central filters B and C and remove any scraps of food with a brush under running water Filters B and C are both removed by lifting
3. Washing programmes chart to help you select the correct programme 5 Door handle To open the door press the catch in the top of the recess and pull the door toward you at the same time To close the door simply push it 6 Programme marker 7 Programme selector dial To select a programme turn the programme selector dial clockwise making sure that the programme letter you wish to select corresponds with the programme marker on the control panel 8 Programme sequence indicator As the programme progresses the programme selector dial turns indicating the phase being performed Each phase is represented by a symbol on the fascia having a precise meaning W Prewash Rinse and Hold Wash a 1 w Cold rinse Hot rinse SM Hot air drying PCP69GB Before use Before using your dishwasher for the first time 1 ensure that the electrical and water connections comply with the installation instructions 2 remove all packaging from inside the appliance 3 fill the rinse aid dispenser Rinse aid Rinse aid is automatically added during the last rinse ensuring through rinsing spot and streak free drying The dispenser which is positioned inside the door holds about 110 ml of rinse aid which is sufficient for 16 40 dishwashing programmes depending upon the dosage setting Filling with rinse aid 1 Open the container by turning the lid A anticlockwise 2 Add the rinse aid unti
4. On 25g 1 cold rinse JUN Any 1 cold rinse 9 Rinse amp Hold Partial load to be D On to avoid food scraps from An completed later in Off sticking to dishes the day This is a special programme for quick washing a full load of lightly soiled dishes glasses and crockery except pots so that you may re use them promptly 12 PWP65GB Operating sequence 1 Checkthe filters Ensure they are clean and properly positioned see cleaning instructions 2 Checkthat there is rinse aid 3 Loadthe dishes Remove any scraps of food Pull the lower basket out and arrange the saucepans plates and cutlery in it Pull the upper basket out and arrange the plates saucers glasses and cups etc in it Slide the basket back into the machine 4 Ensure that the spray arms can rotate freely 5 Measure out detergent Add the required amount of detergent into the dispenser according to the Washing programmes chart and close the lid 6 Close the detergent dispenser lid 7 Close the dishwasher door 8 Setthe programme Turn the programme selector dial clockwise until the letter of the programme you wish to select corresponds with the programme marker If necessary select the temperature of the main wash according to the instructions in the Washing programmes chart see Required pushbuttons 10 11 Start the programme Depress the On Off button
5. connection must be at a height of between 30 cm minimum and 100 cm maximum from the bottom of the dishwasher The drain hose can face either to the right or left of the dishwasher Ensure the hose is not bent or squashed as this could prevent or slow down the discharge of water If you use a drain hose extension it must be no max 100 cm min 30 cm max 100 e longer than 2 metres and its internal diameter must be no smaller than the diameter of the hose provided Likewise the internal diameter of the couplings used for connections to the waste outlet must be no smaller than the diameter of the hose provided The sink plug must not be in place when the machine is draining as this could cause the water to siphon back into the machine Electrical connection Before plugging the appliance into the wall socket make sure that 1 The mains voltage corresponds to the voltage given in the Technical specifications 2 The meter fuses mains power supply and wall socket can all take the maximum load required Make sure that the socket and plug are compatible without having to use any type of adaptor If necessary have the domestic wiring system socket replaced Safety standards require the appliance to be earthed The manufacture accepts no liability for failure to observe the above safety precautions 20 PWA12GB Adjusting t
6. hose extension is not correct Follow the instructions for connecting to the waste m There is no vent in the end of the drain hose The machine is noisy m Dishes are rattling against each other refer to Loading your machine m The spray arms are knocking against the dishes The door is difficult to close m The dishwasher is not level or not properly built in The dishes are not clean poor wash m The baskets are too full m The dishes have not been arranged properly The water inlet funnel in the centre of the upper basket is covered by dishes The spray arms do not rotate The spray arms are clogged The filters are clogged The filters are not in position Not enough detergent has been used or it is unsuitable The detergent is old or has gone hard The washing programme selected is too gentle The dishes are not quite dry The rinse aid has run out or too little is being used 16 PSN16GB If after all these checks the problem persists contact your local Service Force Centre quoting the model and serial number This information can be found on the rating plate located on the right hand side of the dishwasher door see picture Service and spare parts This product should be serviced by an authorised Service engineer and only genuine spare parts should be used Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons may caus
7. BLANCO Makes the difference Instructions for the use and care of your BDW 209 Dishwasher Contents For the user Important safety information Description of the appliance The control panel Before use Rinse aid Use of detergent Using your appliance Loading your appliance Adjusting the height of the upper basket Hints and tips Hints for test centres Washing programmes Operating sequence Maintenance and cleaning Internal cleaning Cleaning the central filters Cleaning the large filter External cleaning Prolonged periods of non operation Frost precautions Moving the machine Something not working Service and spare parts Sales information For the installer 3 Installation instruction 4 Technical specifications Water supply connections 5 Water outlet hose connection 6 Electrical connection 6 7 Adjusting the worktop Fitting under a counter 8 Levelling E Fitting a decor panel on the door 10 11 12 13 14 14 14 14 15 15 15 15 16 17 23 Guide to use the instruction book The following symbols will be found in the text to guide you throughout the instructions A Safety instructions 1 2 3 Step by step instructions i Hints and tips 18 18 19 20 20 21 21 21 22 PCO37GB AN Important safety information It is most important that this instruction book should be retained with the appliance for future reference Should the appliance be sold or transferred t
8. e injury or serious malfunctioning Contact your local Service Force Centre Always insist on genuine spare parts PSNO2GB Installation instruction AN Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person Technical specifications Maximum DIMENSIONS Width 60 cm Height with worktop 88 cm Height without worktop 82 cm Max depth 60 cm Max depth with open door 115 2 cm ELECTRICAL CONNECTION Voltage 220 240 V 50 Hz MOTOR RATING DURING WASH 200W POWER OF HEATING ELEMENT 1900 W OVERALL POWER 2100W WATER SUPPLY PRESSURE Minimum 50 kPa 0 5 bar 800 kPa 8 bar CAPACITY PLACE SETTINGS 12 place settings CONSUMPTION Water Electricity 201 1 5 kW h 18 PTS32 1GB Water supply connections This dishwasher may be fed with either hot max 60 C or cold water Nevertheless we advise you a cold water supply A hot water supply is not always efficient with very soiled crockery as it shortens the washing programmes a lot The water pressure must be within the limits given in the technical specifications Your local Water Authority will advise you on the average mains pressure in your area The dishwasher features fill and drain hoses which can be turned either to the left or t
9. e upper basket After loading your machine always close the door as an open door can be a hazard PBA39GB Hints and tips To save energy Place dishes in the machine immediately after every meal and wait until the dishwasher is full before washing If necessary run the Rinse and Hold programme see Programme Chart on the following pages so that any food scraps do not become caked on the dishes while you are waiting to run the complete wash programme Do not prewash dishes under running water Select an economic programme when the dishes are not very soiled following the instructions given in the Washing programmes chart For best washing results Before loading remove all scraps of food and soak very heavily soiled pots and pans Arrange saucepans cups and glasses etc upside down Tilt items with convex or concave surfaces so that the water drains off easily Avoid contact between the dishes as far as possible You will improve drying results by leaving the dishwasher door ajar for at least 15 30 minutes as soon as the programme finishes Wait a few minutes before removing the dishes in this way they will be cooler and the drying will be improved Empty the lower basket first and then the upper one this will avoid water dripping from the upper basket onto the dishes in the lowe
10. elp to keep your country tidy use authorised disposal sites for your old appliance Warning Dishwasher detergents AN are strongly alkaline they can be extremely dangerous if swallowed Avoid contact with skin and eyes and keep children away from the dishwasher when the door is open PSIO2GB Description of the appliance O m wo IN83 Levelling spacers Upper basket stop Upper spray arm Lower spray arm Large filter Detergent dispenser Control panel Rating plate Rinse aid dispenser 10 Central filters 11 Upper basket 12 Water inlet funnel 13 Worktop 13 12 11 10 PDA15GB The control panel M 12 3 4 5 1 On Off indicator light This comes on when the On Off button is depressed indicating that the machine is on 2 On Off pushbutton On By depressing this button the machine starts operating and at the same time the On Off indicator light illuminates Off When the washing programme has finished the machine stops automatically and the pilot light remains on To switch the indicator light off or to stop the machine at any time press this button 3 Washing temperature selection buttons These buttons allow you to select the temperature of the washing water see Washing programmes chart If no button is depressed the water will be heated to 65 C 4 Programme guide This is a summary of the
11. he right to suit the installation The locknut must be correctly fitted to avoid water leaks Avoid bends or kinks in the hose which could prevent or slow down the water supply If the machine is connected to new pipes or pipes which have not been used for a long time you should run the water for a few minutes before connecting the inlet hose This will prevent deposits of sand or rust clogging the inlet hose filter Be sure to incorporate the filter A supplied with the machine onto the joint For making the connection itself the coupling nut fitted to the machine s supply hose is designed to screw onto either a 3 4 inch gas thread spout or to a purpose made quick coupling tap such as the Press block To make this easier the hose itself may be turned to the left or the right Installation instructions Installer to reinstall the hose in that the hose connection to the dishwasher coupling ensures water seal prior to installation Installer to reconnect all hoses 19 PWA10GB Water outlet hose connection The end of the drain hose can be connected in the following ways 1 To the sink outlet siphon securing it if necessary with a clip 2 Hooked over the edge of the sink using the special curved plastic guide provided 3 Toa stand pipe provided with vent hole minimum internal diameter 4 cm max 100 cm The waste
12. he worktop You can move the worktop forward or backward by 25 mm in order to align the machine with other kitchen units Simply unscrew the two rear retaining screws move the top to the required position and then retighten the screws Fitting under a counter kitchen worktop or sink By removing the machine s worktop you can install it under a close fitting sink unit or a pre existing top providing the dimensions of the recess correspond to those shown in the picture Proceed as follows Remove the machine s worktop by unscrewing the two rear retaining screws pull from the front and slide out the rear slots lifting the worktop Insert the machine after adjusting the height and levelling with the adjustable feet When inserting the machine ensure that the water inlet and drain hoses are not kinked or squashed Levelling Good levelling is essential for correct closure and sealing of the door When the appliance is correctly levelled the door will not catch on the levelling spacers either side of the cabinet If the door does not close correctly loosen or tighten the adjustable feet until the machine is perfectly level 21 INO3 INOS PFI38GB Fitting a decor panel the door The door of this machine has frames for fitting a plastic laminate decor panel in the colour required to match the dishwasher with the rest of the kitchen furnitur If you wish to do this you mu
13. is corrosive acidic or alkaline chemicals must not be washed in this dishwasher Under no circumstances should you open the door whilst the appliance is in operation Always turn off the appliance before opening the door Only use detergent specifically designed for use in dishwashers When finishing loading or unloading close the door as an open door can be a hazard m Donotsit or stand on the open door m Isolate the appliance from the power supply and turn off the water supply after use m Care should be taken when cleaning the bottom door seal and hinge area as any exposed metal edges may cut if care is not taken m This product should be serviced by authorised Service engineer and only genuine spare parts should be used m Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced or unauthorised persons may cause injury or serious malfunction and will void the warranty Contact your local Service Force Centre Always insist on genuine spare parts Conservation In the interest of the environment m Materials marked with the symbol Z5 are recyclable m Check with your local Council or Environmental Health Office to see if there are facilities in your area for re cycling this appliance m When the appliance is to be scrapped cut off the power supply cable and make the door closing device unusable to prevent young children from being trapped inside m H
14. l the container is completely full approx 110 ml The indicator B will be completely dark 3 Top up the rinse aid when the indicator B becomes clear Ensure that the lid is closed after every refill Do not put liquid detergent in the rinse aid department Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash Adjusting the dose According to the finish and drying results obtained adjust the dose of rinse aid by means of the 6 position selector C position 1 minimum dosage position 6 maximum dosage Start from position 3 Gradually increase the dose if there are drops of water or lime spots on the dishes after washing Reduce it if there are sticky whitish streaks on the dishes BRO1 PFRO4GB Use of detergent Only use detergents specifically designed for use in dishwashers To fill the dishwasher with detergent proceed as follows 1 Open the dispenser lid by pulling the catch D 2 Add the detergent according to the recommendations in the programme chart As all detergents are not the same you should also consult the instructions on the packet specially for tablets To help correctly dose the right amount of detergent inside the container there are two reference marks MIN 15 0 30 9 Always close the lid If the programme has a prewash add the required detergent over the lid of
15. ll through the baskets x Open the door and slide out the baskets to load the dishes The lower basket The lower basket is designed to take saucepans lids plates up to 27 cm in diameter salad bowls cutlery etc Serving dishes and large lids should be arranged around the edge of the basket ensuring that the upper spray arm can turn freely The two rear rows of prongs on the lower basket can be easily lowered to allow you to load pots pans and bowls To lower the prongs Slightly pull them upward and let them drop down see picture To bring them back to the standing position just pull them up again The cutlery basket Long bladed knives stored in an upright position are a potential hazard Long and or sharp items of cutlery such as carvings knives must be positioned horizontally in the upper basket Take care when loading or unloading sharp items such as knives Cutlery should be placed in the removable cutlery basket with the handles facing downwards If the handles protrude from the bottom of the basket obstructing the lower spray arm load the cutlery with the handles facing upwards Mix spoons with other cutlery to prevent them from sticking together Silver cutlery tends to go black if mixed with steel cutlery Place it in the cutlery basket separate from the others
16. o another owner or should you move house and leave the appliance always ensure that the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant safety information This information has been provided in the interest of safety You MUST read it carefully before installing or using the appliance Installation This appliance is heavy Care should be taken when moving it It is dangerous to alter the specifications or attempt to modify this product in any way Care must be taken to ensure that the appliance does not stand on the electrical supply cable Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person It is the responsibility of the installer to ensure that the inlet and outlet hoses not be bent or obstructed when the machine is installed If either hose is bent or damaged upon installation it will not be covered by the warranty Child safety This appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play with the product m Keep all packaging well away for children Keep all detergents in a safe place out of children s reach During use Items that are contaminated by petrol paint steel or iron debr
17. ostello Place Seven Hills NSW 2147 PO Box 888 Seven Hills NSW 2781 Telephone 02 8825 9411 Facsimile 02 9674 8897 23 PGU02 1GB DUE CONSTANT DEVELOPMENT WE RESERVE THE RIGHT TO PRODUCT SPECIFICATIONS CHANGES WITHOUT NOTICE BLANCO IS NOT LIABLE FOR ANY INACCURACY OF CLAIMS OR DIMENSIONS IN THIS BROCHURE Total Chlorine free 152994 66 1 th 1 0299
18. r one 10 Items not suitable for dishwashers The following items should not be washed in the dishwasher unless they are sold as dishwasher proof Cutlery with wooden or horn handles or glued parts bronze cutlery saucepans with wooden handles aluminium ware crystal ware leaded glass plastic items antique or fine decorated china Certain types of decoration can discolour when washed in a dishwasher Crystal ware and plastic objects if not guaranteed dishwasher proof should be washed by hand Certain types of glass can also become opaque after being washed several times in a dishwasher A chemical reaction can occur between silver cutlery and stainless steel cutlery As a precaution do not wash together Iron and cast iron objects can rust and stain other items Aluminium tends to go black copper pewter and brass tend to stain i i If in doubt check with manufacturer of the item When buying new dishes ensure that they are dishwasher proof PHT04GB Hints for test centres Before starting any test it is necessary to fill completely with salt the salt container and with rinse aid the rinse aid dispenser Test standard EN 50242 Rerefrence programme Bio 50 C with prewash Load 12 standard place settings Rinse aid selector position 5 formula III Detergent dosage 25 g in the dispenser type B 5 g on the dispenser lid Arrangement
19. st provide the panel yourself that must have the following dimensions Width 588 mm Height 586 mm Max thickness 4mm To fit the panel Take the door frame off after removing the retaining screws around the edge Position the panel refit the frame and tighten the retaining screws around the edge Note The panel should be fitted before positioning the machine 22 PFI39GB Sales information NSW amp ACT HEAD OFFICE 38 Binney Road Marayong NSW 2148 PO Box 6537 Delivery Centre Blacktown NSW 2148 Telephone 02 9621 8488 Facsimile 02 9676 8549 Sales Office and Showroom 331 Pacific Highway Crows Nest NSW 2065 Phone 02 8825 9494 Facsimile 02 9674 8757 VICTORIA State Office and Showroom 1287 1289 Malvern Road Malvern Victoria 3144 Phone 03 9822 0977 Facsimile 03 9822 8492 QUEENSLAND State Office and Showroom Ground Floor Building 1 Bowengate Buisness Park Cnr Bowen Bridge Road amp Campbell Street Bowen Hills QLD 4066 Phone 07 3216 1644 Facsimile 07 3854 1578 SOUTH AUSTRALIA Agent and Showroom Acton Marketing Partners 90 Jervois Street Torrensville SA 5031 Phone 08 8234 9099 Facsimile 08 8234 9200 NEW ZEALAND New Zealand Sales Office Hagemeyer NZ Limited 12 14 Plermark Drive North Habour Auckland NZ Telephone 09 415 8758 Facsimile 09 415 8759 New Address as of 1st Jan 1999 Head Office Sales Office and Showroom 2 C
20. the temperature is below 0 If this is unavoidable empty the machine close the appliance door disconnect the water inlet pipe and empty it Moving the machine If you have to move the machine moving house etc 1 Unplug it 2 Turn the water tap off 3 Remove the water inlet and discharge 4 Pull the machine out together with the hoses Avoid over tilting the machine during transport 2 Something not working Certain problems are due to lack of simple maintenance or oversights which can be solved easily without calling out an engineer Before contacting your local Service Force Centre please carry out the checks listed below Symptom Solution The machine will not start m The door has not been properly closed m The plug is not properly inserted in the power socket m here is not current at the socket The dishwasher does not fill with water m Ensure the water tap is open m Ensure the mains water supply has not been cut off m The inlet hose may be squashed or bent Reposition the hose m The inlet hose may be blocked Switch off the water supply and clean the filter The filters are blocked m Clean the filters refer to Maintenance and cleaning The spray arms are not rotating m Ensure the crockery is loaded correctly The dishwasher will not drain m The drain hose may be squashed or bent Reposition the hose m The sink may be blocked Clear any blockages m The drain
21. the dispenser If using detergent in tablets proceed as follows 1 For all programmes add 1 tablet inside the detergent dispenser 2 Always close the dispenser lid 3 For all programmes with prewash add a portion of a further tablet on the lid of the detergent dispenser Check that the detergent receptacle is empty after completion of the wash cycle Insufficient quantities of detergent will produce poor washing results whereas an excessive amounts of detergent will not improve washing results and is also wasteful Using no more than the correct amount also contributes to reducing pollution Phosphate free detergents with enzymes In these low alkaline compact powders the environment unfriendly components have been replaced by natural enzymes and other more biodegradable substances The enzymes deploy their full dirt dissolving power at a temperature as low as 50 C By choosing the Bio programme you can therefore achieve the same cleaning results that would otherwise be achievable only with 65 C programmes and conventional detergents These new compact powders are generally phosphate free 7 PUD12GB Using your appliance Loading your appliance Before placing dishes in the machine remove any scraps of food to avoid clogging the filters and consequently reducing the performance Al LA AES SN pw 02 YS 22 LS X lt s Do not load very small items which can fa
22. up the outer one B pulling the central funnel upwards the smaller filter C can be removed by pressing the two tongues D Once cleaned refit the filters by pressing them down until they click into place Cleaning the large filter Once a month Clean the large filter A on both sides under running water using a brush To take it out remove the spray arm by pressing the two tongues E turn the ring F anticlockwise and then slide the whole part out Refit the filter following the above instructions in reverse order The dishwasher must not be used without filters Incorrect repositioning and fitting of the filters will produce poor washing results Cleaning the filters is vital to ensure correct operation of the machine 14 SE PMCO08GB External cleaning Clean the external surfaces of the machine and control panel with a damp soft cloth If necessary use only neutral detergents Never use abrasive products scouring pads or solvent acetone trichloroethylene etc Prolonged periods of non operation If you are not using the machine for any period of time you are advised to 1 Unplug the appliance and then turn off the water 2 Fill the rinse aid dispenser 3 Leave the door ajar to prevent the formation of any unpleasant smells 4 Leave the inside of the machine clean Frost precautions Avoid placing the machine in a location where
23. upper basket Arrangement lower basket 11 Washing programmes Programme Degree of soil Starting Required Recommended quantity Cycle of detergent E and type of load position ofthe pushbuttons inthe onthe description programmer dispenser dispenser x Hot prewash 1 Intensive Heavy soil On Main wash up to 70 C Crockery cutlery A 1 259 10g 2ooldrinses 0 pots and pans 1 hot rinse Hot air drying 2 Normal Cold prewash h Normal soil Main wash up to 65 C with prewash Crockery and A on 250 59 i cold rinse 15 cutlery MM us ot air drying 3 Normal Light soil Main wash up to 65 C no prewash Code d B on 25g 1ooldrinse ot rinseHot air drying 17 cutlery boa 4 BIO Normal soil Cold prewash s Main wash 50 C with prewash Crockery and A BIO On 25g 99 tx cutlery Off 1 hot rinse gt Hot air drying no umm E rus On 25 B BIO Off 9 1 hot rinse 17 cutlery Hot air drying gt 5 Cold prewash 6 Economic Normal soil Main wash 55 C with prewaSh Crockery and A n 25g 59 tcoldrinse cutlery Off 1 hot rinse gt Hot air drying 7 Economic Main wash up to 55 C Light soil aen up 1 col prewash Crockery and B E on EE ects cutlery Hot air drying r i h Light soil Main wash up to 55 C 8 Quick was Ga nae C E
Download Pdf Manuals
Related Search