Rhino-Rack - Fitting Instructions - Accessories - 571
Contents
1. 11 Loop the straps under the crossbar as shown FRONT cradles shown here Page 11 of 112. RHINO RACK Rhino Rack CLW SERIES 571 581 Important Please read these instructions carefully prior to installation Please refer to your fitting instruction to ensure that the kayak carrier is installed in the correct locations Check the contents of kit before commencing fitment and report any discrepancies Place these instructions in the vehicle s glove box after installation is complete Important Information Maximum carrying capacity Refer to maximum carrying capacity of roof racks Please refer to your vehicle manufacturers handbook for maximum carrying capacity of your roof racks Always use the lower of the two figures Load must be evenly distributed over the crossbars Warning Do not attempt to fit the 571 581 to your vehicle unless you fully understand these fitting instructions Please direct any questions regarding fitting to the dealer from where the 571 581 was purchased Use only non stretch fastening ropes or straps Ensure the bottom of the kayak is clean before loading to avoid damage to both kayak and cradle Take care when loading and unloading to ensure that the kayak does not damage the vehicle The roof racks must be at least 600mm apart for safe use Failure to follow these warnings and instructions set out will void warranty Recommendations It is essential that all bolt connections be checked after driving a short distance when you first install your kayak cradles Bolt connections should be checked a
3. ed position cradles over the FRONT cross bars 4 Securely tighten screws with the allen key supplied Page 4 of 11 ear Rhino Rack Q ZVQUSSERIES 571 581 Page 5 of 11 D Rhino Rack QLA SERIES 571 581 PE Load the kayak onto the REAR cradles It may be necessary to readjust the position to ensure it fits securely Page 6 of 11 Rhino Rack Q ZVQUSSERIES 571 581 8 Straps should always pass under the crossbar as shown Pull tight a Outside of vehicle Page 7 of 11 581 N IO N ad LLI N 581 Fitting Instructions Rack Rhino Insert T bolts into channel and tighten dials Alternative setup Locks can also face inwards Insert locking covers O Page 8 of 11 D Rhino Rack LWA SERIES 571 581 4 Insert T bolts into channel and tighten dials EMM Insert locking covers Page 9 of 11 D Rhino Rack QLA SERIES 571 581 T Load the kayak onto the REAR cradles It may be necessary to readjust the position to ensure it fits securely Page 10 of 11 Rhino Rack Q ZVQUSSERIES 571 581 10 Straps should always pass under the crossbar as shown Pull tight fe Outside of vehicle gt
4. f sealed roads the manufacturer ae 60kg load rating _ 30kg load rating maximum roof load rating to be Urban road Offroad 60kg 2 found in the vehicles User Manual y should be halved Do not forget to subtract 7 5kg from your maximum carrying capacity due to the weight of the crossbars and legs WARNING Important Load Carrying Instructions With utility vehicles the cabin and the canopy move independently Roofracks and vehicle can be damaged if the item transported is rigidly fixed at points on both the cabin and canopy Instead rigidly fix to either the cabin roofracks or the canopy roofracks Page 2 of 11 ear Rhino Rack Q ZVQUSSERIES 571 581 Parts List 571 Item Component Name M6 x 40mm Security Head Screw 8 M6 Flat Washer 8 Front Cradle Rear Cradle Bottom Bracket 6 M6 Nut in bottom bracket 8 5 5m Tie Down Strap 8 Allen Key 9 3m Covered Buckle Strap Fitting Instructions QUUISSERIES 571 581 fit kit sold separately roof clearance item Component Name Qty Pe Rear Cradle f Te _ _SsmTie Down Sap 2 e am Covered Buckle Srap 2 571 Fitting Instructions Pages 3 6 581 Fitting Instructions Pages 7 9 Page 3 of 11 581 N Lo N uw Lu N Q lt q Z Rack Rhino amp 571 Fitting Instructions Loosely attach one side 3 With one side attach
5. gain at regular intervals once a week is enough depending on road conditions usage loads and distances travelled You should also check the roof racks and kayak cradles each time they are re fitted Always make sure to fasten your load securely Please also ensure that all loads are evenly distributed and that the centre of gravity is kept as low as possible Long loads e g canoes and kayaks must be secured front and rear with non stretch fastening ropes or straps Roof racks must be removed when putting vehicle through an automatic car wash Caution The handling characteristics of the vehicle changes when you transport a load on the roof For safety reasons we recommend you exercise extreme care when transporting wind resistant loads Special consideration must be taken into account when cornering and braking Note for Dealers and Fitters It is your responsibility to ensure this fitting instruction is given to the end user or client Rhino Rack 3 Pike Street Rydalmere NSW 2116 Australia Document No R234 Ph 02 9638 4744 Prepared By Andy Wana Issue No 01 Fax 02 9638 4822 Authorised By Chris Murty Issue Date 22 10 2012 These instructions remain the property of Rhino Rack Australia Pty Ltd and may not be used or changed for any other purpose than intended Page 1 of 11 When these roof racks are to be used on a vehicle that is driven of
Download Pdf Manuals
Related Search