THE AMAZING HAWKEYE
Contents
1. RGBW 4 in 1 LEDs Voltage AC100 240V 50 60 Hz Power consumption 360W Control Mode Master slave DMX Beam angle 6 degree Strobe 0 25 Hz Color RGBW Channel 18 Channels Working Temperature 25 C 40 C Working Lifetime 50000 hours Pan 540 speed controllable Tilt 205 speed controllable IP rate IP 20 Indoor use only Fixture Dimension 25 30 36 cm Package 1pc CTN Packing dimension 40 33 47 CM Net weight 8 KG Gross weight 10 5 KG Special points 1 Lamp board plate can rotate continuous 360 to make amazing effect Speed controllable 2 Built in with 85 static effects 85 dynamic effects multiple built in programs 3 Special LENS unique design to make amazing effect 2 Safety Instructions CAUTION Be careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual gt Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the2. device Leave the device switched off until it has reached room temperature This device falls under protection class Therefore it is essential that the device be earthed The electric connection must carry out by qualified person The device shall only be used with rate voltage and frequency Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually Please don t project the beam onto combustible substances Fixtures cannot be installed on combustible substances keep more than 50cm distance with wall for smooth air flow so there should be no shelter for fans and ventilation for heat radiation If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard 3 Operation Instructions The moving head is for wash effect for on site decoration purpose Don t turn on the fixt
3. CE THE AMAZING HAWKEYE 19PCS 12W 4 in 1 C W 5 IP20 co ozm tasoc te 150 C User Manual KEEP THIS MANUAL FOR FUTURE NEEDS 1 Unpacking Thank you for choosing our HAWKEYE For your own safety please read this manual before installing the device This manual covers the important information on installation and applications Please install and operate the fixture with following instructions Meanwhile please keep this manual well for future needs The Amazing HAWKEYE is made of a new type of high temperature strength of engineering plastics and cast aluminum casing with nice outlook The fixture is designed and manufactured strictly following CE standards complying with international standard DMX512 protocol It s available independently controlled and linkable with each other for operation And it is applicable for large scale live performances theater studio nightclubs and discos 4 IN 1 LEDs RGBW which features high brightness and stability Please carefully unpack it when you receive the fixture and check whether it is damaged during the transportation And please check whether the following items are included inside the box Moving Head One Signal Cable One Hanging Bracket Two Power Cable One Safety Cable one User Manual One 1 10 Maintenance and Cleaning The following points have to be considered during the inspection 1 All screws for installing the devices o
4. an T _ Invert pan setting Z Invert Tilt Invert Tilt setting OFF Set Pan Tilt Swap setting Pan Tilt Swap PT FF Menu O Z Pan Tilt Encoder Pan Tilt Encoder setting KEEP No DMX Signal DMX Signal settine ON i Display Display setting OFF OK Recover to Load Default Default setting Press to enter Manual mode Check the system information Input code to advanced setting
5. ever stand directly below the device when mounting removing or servicing the fixture froma periodic safety inspection of all installation material and the fixture If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet Clamp Mounting The HAWKEYE provides a unique mounting bracket assembly that integrates the bottom of the base the included Omega Bracket and the safety cable rigging point in one unit See the illustration below When mounting this fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a M10 screw fitted through the center hole of the omega bracket As an added safety measure be sure to attached at least one properly rated safety cable to the fixture using on of the safety cable rigging point integrated in the base assembly Omega Bracket Batoty Clamp Safaty Cable 1 2Turn Quick Lock Fasteners Regardless of the rigging option you choose for the HAWKEYE always be sure to secure your fixture with a safety cable The fixture provides a built in rigging point for a safety cable on the hanging bracket as illustrated above Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle 5 DMX 512 contro
6. ixtures in areas outside walking paths seating areas or in areas were the fixture might be reached by unauthorized personnel Before mounting the fixture to any surface make sure that the installation area can hold a minimum point load of 10 times the device s weight Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable 8 Photometric Data LUX Data of 6 degree beam angle 2m 4m 6m LUX Data of 45 degree beam angle Lens rotate Sm 6 Beam Angle 50 Beam Angle 7 DMX Channels Pan Fine 0 127 0 360 degree movement Lens rotate LENS 360 continuous movement without limitation from slow to fast Speed of lens rotate Speed from fast to slow Linear dimmer from dark to bright Strobe with the same step from slow to fast 1Hz 25Hz 51 Static built in effects show please operate against the Channel 6 51 Dynamic built in effects show please operate against the Channel 6 From slow to fast Operate against with 15th channel 56 75 LED Auto run 1 static effect show 76 95 LED Auto run 2 dynamic effect show Lens and LED Auto run 1161385 Pan Tilt Auto run 76195 Aworna 216 235 Randomauorn 236 255 Sound activated Reset within 5 seconds Dynamic built in effects effect speed Macro function t 7 2 O3 4 O 5 ES 58 o 10 On __12__ OB M seem erens s s N
7. l connections Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head You can chain multiple Moving heads be connected together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below DMX 512 connection with DMX terminator Controller DMX Output DMxX Input 3 Pin XLR Socket 3 Pin XLR Socket COMMON kea DMX512 OUT DMX512 IN 3 Data 3 PIN XLR DMX 3 PIN XLR For installations where the DMX cable has to run a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 1200 2 y 1 PIN3 PIN 2 6 Menu Operations Button instruction Previous item Return to last item ox Return to Main Menu Next item Menu details and function J M TO 1 gt c TO 2 mode setting gt 4 4 gt c Run Mode TO 3 gt c JTO 4 Random Sound DMX address setting DMX Address 001 512 Channel mode 18 CH Z Invert P
8. r parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed a gt CAUTION Disconnect from mains before starting maintenance operation In order to make the lights in good condition and extend the life time we suggest a regular cleaning to the lights 1 Clean the inside and outside lens each week to avoid the weakneness of the lights due to accumulation of dust 2 Clean the fan each week 3 Adetailed electric check by approved electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine parts from your local dealer 10 9 Key Features LED Light Source 19pcs 12W
9. ure if its been through severe temperature difference like after transportation because it might damage the light due to the environment changes So make sure to operate the fixture until it is in normal temperature This light should be keep away from strong shaking during any transportation or movement Don t pull up the light by only the head or it might cause damages to the mechanical parts Don t expose the fixture in overheat moisture or environment with too much dust when installing it And don t lay any power cables on the floor Or it might cause electronic shock to the people Make sure the installation place is in good safety condition before installing the fixture Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture Make sure the lens are in good condition It s recommended to replace the units if there are any damages or severe scratch Make sure the fixture is operated by qualified personnel who knows the fixture before using Keep the original packages if any second shipment is needed Don t try to change the fixtures without any instruction by the manufacturer or the appointed repairing agencies It is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation like shock short circuit electronic shock lamp broke etc 4 Mounting and Installation Cautions For added protection mount the f
Download Pdf Manuals
Related Search