DOC US 1
Contents
1. gt CAMERA ID If inputted ID Camera ID will be displayed onto the screen 1 Move the arrow indicator to Camera ID by pressing of UP or Down button on the SETUP Menu screen 2 Set ON by using of Left or Right button CAUTION When Camera ID is set to OFF The Camera ID will not displayed onto the monitor 3 Press the SETUP button CAMERA ID ABCDEFGHIJKLM NOPQRSTUVWXYZ abcdefghijklm nopqrstuvwxyz 0123456789 CLR POS END USER S MANUAL 4 ID could be entered up to 15 characters 1 Move the cursor to character enter location by using of Left or Right button CAMERA ID ABCDEFGHIJKLM NOPQRSTUVWXYZ abcdefghijklm nopqrstuvwxyz 0123456789 CLR POS END 2 Select the desired character in A B Y Z a b y z 0 1 8 9 by using of Up Down Left And Right button 3 Set the desired character by pressing of SETUP button The cursor will move to next position after character select by pressing SETUP button 4 Repeat above steps until created the desired full name CAUTION a In Case of Wrong Camera ID Input Move the cursor to CLR and press the SETUP button from right to left to erase the characters And repeat above steps to correct the characters again 5 Select the position at camera ID should be located on the screen D Move the cursor to POS and press the SET button CAMERA ID ABCDEFGHIJKLM NOPQRSTUVWXYZ abcdefghijklm nopqrstuvwxyz2. 0123456789 ne 19 18 USER S MANUAL 2 Created Camera name will be displayed 3 Select the position by using of the 4 Directional button then press the SET Button to confirm the position 6 Move the cursor to END and press the SET button after completed the above processing gt COLOR Electronic DAY amp NIGHT AUTO Electronically sensing Day amp Night Fixed only color mode Iz CAUTION u Color mode could not available when AGC OFF 19 USER S MANUAL SYNC The line lock synchronization is used in only areas of 60Hz NTSC and 50Hz PAL Press Set to Return INT Internal Synchronization L L Line Lock mode Press the SETUP button It could be adjusted to desired phase from 0 to 359 CAUTION DC 12V the SYNC menu sets INT mode 20 USER S MANUAL gt MOTION DETECTION MD Whenever the camera detects motion of object displaying Motion Detected with the counting up of number on the Screen Press the SETUP button OFF Deactivation quel MES Lou AREA SEL AREA1 ON Selected AREA will bedetected AREA STATE by MOTION sensing In AREA SEL it could be selected desired detection area by each cameras PRESS SET TO RETURN Set ON selected AREA state Activated Move the arrow indicator to adjust sharpness of detection Area by using of TOP BOTTOM LEFT RIGHT Press the SETUP button
3. High reduction of noise but ghost effect will be appear MIDDLE Middle reduction of noise but most effective with less ghost effect LOW Low reduction of noise without ghost effect OFF Deactivation SETUP LENS SHUTTER WHITE BAL BACKLIGHT AGC gt SENS UP OFF SPECIAL 4 EXIT USER S MANUAL It could be always displayed clear image with this function even under low level or night time 1 Move the arrow indicator to SENS UP by pressing of UP or Down button on the SETUP Menu screen 2 Select the desired mode by pressing of Left or Right button AUTO Auto mode status e OFF Deactivation CAUTION When AGC OFF SENS UP does not working When SHUTTER selected to MANUAL SENS UP does not working SENS UP OFF 3 Press the SETUP button when completed the menu set t CAUTION If press the SETUP button it could be controlled maximum magnifications Adjusted to 12 Step Expanding magnifications screens brighter after image sensitivity but increasing the noise on the screen When SENS UP activated increasing magnification makes noise spots and whitish It is not out of order 16 USER S MANUAL SPECIAL 1 Move the arrow indicator to SPECIAL by pressing of UP or Down button on the SETUP Menu screen 2 Select the desired mode by pressing of Left or Right button SPECIAL 2 CAMERA ID COLOR SYNC MOTION DET PRIVACY MIRROR SHARPNESS RESET RETURN
4. DNR Hood True Day Night Weather proof IR Camera DC Auto Iris Varifocal Lens 4mm 9mm IR LED Built in 56 pcs E Illumination 7 FILTER CHANGE o ooon a DC VIDEO LENS SPECIFICATIONS _ Image Pick Up Device TV System Total Pixels Effective Pixels Scanning Frequency Scanning System Synchronization Resolution Minimum Illumination S N Ratio White Balance Gamma Characteristic Video Output Electronic Shutter Speed OSD BLC AGC DNR Day amp Night Color Sharpness Privacy Power Supply Power Consumption Lens Operational Temp Storage Temp Dimension Weight 5 HD D503NW 560TV Lines DC Auto Iris Varifocal Lens 4mm 9mm IR Day Night Capability 850nm IR LEDs 56pcs 5 HD D503NWT 560TV Lines DC Auto Iris Varifocal Lens 4mm 9mm True Day Night Capability ICR IR Cut Filter Removable 850nm IR LEDs 56pcs 1 3 SONY SUPER HAD CCD NTSC PAL NTSC 811 H 508 V PAL 795 H 596 V NTSC 768 H 494 V PAL 752 H 582 V NTSC 15 734KHz H 59 94Hz V PAL 15 625KHz H 50 00Hz V 2 1 Interlace Internal 560TV Lines CDS OFF 0 1Lux CDS ON 0 00006Lux More than 50dB ATW AWBC MANUAL 1800 K 10 502 r 0 45 CVBS 1 0Vp p 75ohm NTSC Auto Manual 1 60sec 1 120 000sec PAL Auto Manual 1 50sec 1 120 000sec Built in Low Middle High Off Selectable Low Middle High Off Selectable Low Middle High Off Selectable On Auto Selectable Electrical On
5. L SHUTTER ESC WHITE BAL ATW gt AGC Low DNR LOW SENS UP OFF SPECIAL 4 EXIT HIGH Gain could be increased max from 6dB to 34dB MIDDLE Gain could be increased max from 6dB to 30dB LOW Gain could be increased max from to 18 OFF BACKLIGHT function will not operated BLC OFF USER S MANUAL AGC AUTO GAIN CONTROL Move the arrow indicator to AGC by by pressing of UP or Down button on the SETUP Menu screen Select the desired mode by pressing of Left or Right button AGC is for bright image Higher gain level makes brighter screen but increases the noise HIGH Gain could be increased from 6dB to 34dB MIDDLE Gain could be increased from 6dB to 30dB max LOW Gain could be increased from 6dB to 18dB max OFF Gain will be fixed at 6dB NO SETUP LENS MANUAL SHUTTER ESC WHITE BAL ATW BACKLIGHT OFF a AGC DNR LOW SENS UP OFF SPECIAL EXIT 3 Press the SETUP button The BRIGHTNESS could be adjusted from 1 to 70 max Brightness BRIGHTNESS 35 Press Set to Return 4 Press the SETUP button when completed the menu set up 14 USER S MANUAL DNR Digital Noise Reduction DNR is to reduce the digital noise on the screen 1 Move the arrow indicator to DNR by pressing of UP or Down button on the SETUP Menu screen 2 Select the desired mode by pressing of Left or Right button HIGH
6. Off Level Adjustable On Off 4 Programmable Zone DC 12V CDS ON 600mA Max DC Auto Iris Varifocal Lens 4mm 9mm 10 50 Deg C RH 95 Max 20 60 Deg C RH 95 Max 100mm W 134mm H 251mm D 1700g General Features poccccccccccccccccccccccce Third Generation DSP Chip 1 3 Sony Super HAD CCD Removed Noise Ghosting Effect with DNR True Day amp Night ICR IR Cut Filter Removable External Control Rings for Easy Focus amp Distance Adjustment Highest Resolution Vivid Sharp Picture in completely darkness DC Auto Iris Varifocal Lens 2 8mm 12mm 3 5mm 16mm 9mm 22mm Option Dual Power AC 24V DC 12V Option OSD Remote Control Option Dimensions 251mm SIDE 360 180 68mm Digital Day Night Color Camera 5mm 50mm 4 i 360 100mm OSD REMOTE CONTROL OPTION SETTING Settings can be made using the OSD button located in the body housing NS DC SHUTTER SPEED WHITE BAL ATW Wiress Remote Controller Option OSD A v 4 CAMERA OPERATION SET UP UP DOWN LEFT RIGHT eATW eAWC eMANUAL eOFF eLOW eMIDDLE eOFF eLOW eMIDDLE eOFF eLOW eMIDDLE eOFF AUTO eCAMERA eCOLOR eSYNC eMOTION DETECTION ePRIVACY eMIRROR eSHARPNESS eRESET eRETU
7. R technology enhanced incredibly minimum illumination of amazing 0 0002 Lux With capture of good image under the extremely low light conditions OQ DNR Digital Noise Reduction DNR technology solved the trouble of ghost figures it displaying clearer superior High resolution even in extremely low light circumstance 1 Disk Saving Effects Up most and advanced DNR technology camera picture quality has a disk saving effects due to Image sizes are smaller than standard CCTV camera image TESI Controlled by OSD Menu OSD The camera can be controlled by selecting the menu text displayed on the monitor screen USER S MANUAL OSD Control Button 1 Type A Type B Type C of OSD button could be used when it needs to OSD control 2 Type D is extra Option wired Remote controller Type A Type B e LEFT SETUP RIGHT SETUP UP DOWN LEFT RIGHT DOWN Type C Type D Option UP 1 LEFT lt RIGHT SET UP DOWN USER S MANUAL How to Set Up the camera menu Setup Menu LENS MANUAL Q DC VIDEO SHUTTER Shutter Speed control WHITE BALANCE ATW 9 AWC 9 MANUAL BACKLIGHT BLC 9 OFF o0 LOW MIDDLE HIGH AGC Auto gain control OFF LOW MIDDLE HIGH DNR Digital Noise reduction o OFF o LOW MIDDLE o HIGH 9 CAMERA ID COLOR ADJUST 9 SYNC 9 MOTION DET PRIVACY MIRROR SHARPNESS RESET B RETURN e Menu Set U
8. RN HOW To Install 1 e eorr rrr CDS Sensor m C m c ect gt gt o e v D 5 Nn 4mm 9mm Camera Adjustment 009000090090000900000009000090090000000000090000900090000000900009009 0 Connect Video amp Power Line 12V DC Regulated Power 2 Please set the position where you want to connect the camera 3 Loosen the locking screws and adjust camera angle 4 Combine each camera part and lock amp tighten each locking screw Operating Manual USERS INSTRUCTIONS High Resolution DNR Day Night Color Camera 1509001 138014001 ROHS USER S MANUAL CAUTION DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL IS014001 The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance INFORMATION This equipment has been tested and found to comply with limits for a Class A digit
9. al device pursuant to part 15 of the FCC Rules amp CE Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARNING Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment CAUTION To prevent electric shock and risk of fire hazards i Do NOT use power sources other than those specified Do NOT expose this appliance to rain or moisture This installation should be made by a qualified service person and should conform to all local codes USER S MANUAL Sefety Instructions Precautions for use Q Please read this manual enough before using this camera to obtain the skill of correct operation Warranty 9 This manual is including Warranty Card at last page This warranty card is available within One 1 year from the 1st date when you purchased this unit and keep this warranty card well for A S The A S cost would be free of charge except only user s fault in warranty year 9 Keep the c
10. amera box well and it could be used when it need to have after Service Cautions when using 9 Do not open the camera body and touch to prevent electric shock Q Do not insert other object into camera body to prevent hazards of fire and electric shock 9 Do not touch with wet hands to prevent electric shock Must pull out by taking plug socket Q If the camera has burning smells please plug out and ask to shop where you bought It or the nearest A S center Cautions when Install Plug on after installation of all device Do not install the camera face to strong light directly Q Do not install or use the camera in places where the humidity is high Q Do not install near the cooling device or heating device Q Do not install the camera where is high humidity or heavy dust Q Do not install the camera to the place where it has physical shocks 9 Do not expose the camera to rain or moisture This products must use DC adaptor for power USER S MANUAL Precautions Only use the camera under conditions Severe lighting change or flicker can where temperatures are between cause the camera to work improperly 10 C and 50 C Be especially careful to provide ventilation when operating under high temperatures This is one of the most important parts of the It can cause malfunctions to occur Severe lighting change or flicker can camera Be careful not to leave cause the camera to work improperly fingerprints on
11. e 1 70 LENS BRIGHTNESS 35 Press Set to Return gt MANUAL Manual Lens 3 Press the SETUP button to return previous menu 10 USER S MANUAL SHUTTER SPEED CONTROL It s a function of selecting the Automatic shutter speed control or Manual shutter speed control 1 On the Set Up menu screen move the arrow indicator to shutter by using of UP or Down button 2 Select desired shutter mode by pressing of Left or Right Button FLK Select FLK mode when it has flickering by unmatched of electric lights and radio waves ESC Available automatic shutter speed control Brightness could be automatically controlled when Selected ESC mode MANUAL Shutter speed could be controlled by manually SHUTTER ESC 3 Manual shutter speed could be controlled when select Manual shutter speed could be controlled from 1 60 to 1 120 000sec 4 Press the Set Up button to exit after completed the set up menu CAUTION Lens Shutter speed will be fixed to 1 60sec when selected DC VIDEO lens Do not make the camera exposed fluorescent lamp directly It should be caused of unstable image quality in the internal synchronization mode In case of Shutter menu selected to Manual mode SENS UP does not work Please control the menu 11 USER S MANUAL WHITE BALANCE Use the White Balance function when need to color control on the screen 1 Move the arrow indicator to WHITE BAL b
12. p Menu could be adjusted by the OSD button of the camera 1 Press the setup button Setup menu will display on the monitor LENS MANUAL USER S MANUAL 2 Move and Select the function what you want to control by the button Move the arrow indicator UP or Down to indicate onto desired feature by pressing the UP or Down button SETUP Select desired LENS MANUAL Change the Feature SHUTTER adjustment WHITE BAL ATW by Left or BACKLIGHT OFF Right button AGC Ko DNR SENS UP OFF SPECIAL 4 3 Menu Set Up will change by Left or Right Button Available value or Status will be displayed by pressing the Left or Right button Please press the button until desired features appears 4 After complete the adjustment move the arrow indicator to EXIT and press the SET button to Exit CAUTION Moving available to submenu by moving the lt arrow to desired feature Access are not available to submenu on the mode of USER S MANUAL LENS Option It s function of control the picture brightness 1 Move to arrow indicator to LENS by pressing of UP or Down button on the Set Up menu screen 2 Select the desired lens type by pressing of Left or Right button SETUP lt LENS SHUTTER WHITE BAL BACKLIGHT AGC DNR SENS UP SPECIAL EXIT DC VIDEO DC Auto IRIS Lens CAUTION Available to control the brightness when selected DC Brightness control range will b
13. the lens cover N NN N NN un If it gets wet wipe dry immediately If exposed to radioactivity the CCD Liquids can contain minerals that will fail corrode the electronic components USER S MANUAL General Features e n 6 Q Operating Key Button MM 7 Camera Menu Set Up eMe 8 1 LENS ODON patebit Dade M AE RUE 10 2 SHUTTER 11 3 WHITE BALANCE 12 BACK ICHI DCC erien 13 5 AGC Function Auto Gain Control 14 EAR 15 i M 16 17 USER S MANUAL General Features DNR DSP Chip DNR is superior DSP chipset enhanced various and powerful function of high resolution Day amp Night Removing camera noise and sense up as well It is the highest and advanced technology that is unified Up most necessary functions by one DSP chipset enhanced powertul surveillance functions Q 560TV Lines Unification of DNR Technology and Sony Super HAD CCD image sensor provides Clear amp Superior High resolution of 560 TV lines Day amp Night Up to the lighting conditions the video automatically switching to color mode in bright zone and Monochrome mode in dark zone making to achieve safe and perfect 24 hours surveillance se Q Electronic IRIS The electronic IRIS function enables continuous automatic control of the shutter between 1 60 1 50 1 120 000 seconds Q Illumination Ultra Advanced DN
14. to save the selected data CAUTION MD will be displayed on the screen but there is not OUTPUT signal It masking the area which is desired areas to mask OFF Deactivated ON PRIVACY mode activated Press the SETUP button PRIVACY AREA SEL AREA1 _ n AREA SEL it could be Erico ER selected desired masking area AREA TONE by each Cameras TOP Set ON selected AREA state ep Activated RIGHT Move the arrow indicator to PRESS SET TO RETURN adjust sharpness of Privacy Area by using of TOP BOTTOM LEFT RIGHT Privacy area tone could be adjusted by using of Area tone 21 USER S MANUAL MIRROR ON Activated Reverse turning Right to Left OFF Deactivated MIRROR OFF MIRROR ON SHARPNESS To make image clear Sharpness level needs to up The level could be controlled to get SHARPNESS proper image When level is too much higher LEVEL it would by caused of unnatural mage with the noise Press the SETUP button Press Set to Return It could be controlled desired LEVEL from 1 to 31 gt RESET Factory default set gt RETURN Save the setting of SPECIAL function and then move to SETUP menu EXIT Save the all of setting menu and exit 22
15. y pressing of SET button on the SETUP Menu screen 2 Select desired mode by using of Left or Right button WHITE BAL ATW Select in below 3 functions up to user s purpose ATW It is suitable in the color temperature ranges from 1 800 to 10 500 AWC In order to obtain the best result press the Set button while the camera focuses on to White paper If the environment and or lights source has changed it could be readjusted the white balance MANUAL Available to fine adjustment in case of selected to Manual mode After adjustment of ATW or AWC select the manual mode and press the SETUP button to increase or decrease the value of R Gain RED and B Gain Blue while watching the color of image Press the SET button when obtained the desired best color CAUTION Proper White Balance may not be worked under the following conditions In that case Select the AWC mode When the scene of object has most high color temperature Ex Blue Sky Sunset When the scene of object is so dim When install the camera in place of the changing illumination and or faces directly to Fluorescent lights 12 USER S MANUAL Backlight BLC This camera provide intelligent light level control to overcome the severe Backlight condition 1 Move the arrow indicator to BACKLIGHT by pressing of up or Down button on the SETUP Menu screen 2 Select the desired mode by pressing of Left or Right button SETUP LENS MANUA
Download Pdf Manuals
Related Search