GSM/GPRS/GPS Tracker (LDW
Contents
1. Vibration Alarm Setup Format ZDBJ sensitivity 1 15 alarm mode 0 1 Sensitivity 1 is the most sensitive and of course 15 is the most insensitive Alarm mode 0 indicates vibration alarm is closed Alarm mode 1 indicates the device will alarm you through calls or SMS Note SMS will be sent only when the device is online on the tracking system For example If you set ZDBJ 1 1 the device will send you back Config OK The Vibrate Warning Is 1 1 That means that the tracker is in a most sensitive status and alarm by calls Cut oil supply by SMS Format DY password state The value of state is 0 and 1 1 is cut off oil 0 is restore oil Example DY 000000 1 For safety this command will be function when the speed less than 5KM h After sending command successfully the tracker will return a message config OK and cut oil supply of the vehicle Over speed Alarm Setup Format CSBJ speed limit km h state The value of state is 0 and 1 1 means open over speed alarm 0 means close over speed alarm Example CSBJ 80 0 After sending command successfully the tracker will return a message config OK The Warning Speed Is 80 Off Time Zone Setup Format 896 E or W time zone The value of state is E and w E means eastern time zone W means western time zone2. the terminal state Red LED Power Running state The state of the light Meaning Always light Indicate the power supply normal working state Flash Abnormal working state No light Out of power or internal fault Green LED GPS Signal The state of the light Meaning Always light GPS signal received normally No light GPS signal close Blue LED GSM Signal The state of the light Meaning Always light GSM signal OK Call coming No light GSM signal close GSM Indicator GPS Indicator 2 4 4 Accessories Power Indicator Cable Connector my Connect cable Standard Screws Standard Lighter power cord for car option Relay Standard 2 5 Installation 2 5 1 Preparation 1 Check the product open the package and check the terminal model and fittings If there is something wrong please contact the distributor 2 Select the SIM card it must insult a GSM SIM card and the selection of SIM card must follow the distributor s suggestion 3 Install the SIM card Firstly open the cover of the terminal remove the cover on the slot for SIM card secondly insult the card into the slot with the metal side in the bottom thirdly fasten the slot do as the following instruction finally recover the terminal and lock the shell tightly with three screws Don t insult the terminal SIM card up sid
3. with the following steps a Check the red indicator if not light check the terminal connections at the fuse or power supply terminal it also can be measured with a millimeter to check the 2P main power line voltage if the voltage is normal then please remove the terminal machine and send it back to the original dealer for maintenance service b If the red power indicator is constantly on green light for GSM is not on then please check SIM card is properly installed if the installation has no problem and please change for another SIM card to use 2 9 2 When the GPS signal reception is abnormal Please drive to a more open area to locate It takes one or two minutes for the first time If it does not locate please check the installation location of the terminal which is usually installed in the place without metallic shelter 2 9 3 When the GSM signal reception is abnormal Please check whether the terminal s SIM card is correctly installed or the place may not be covered by GSM signal such as in the basement please drive to the places covered by signal 2 9 4 At the moment connecting power If the red light is not on check the insurance of power lines to see whether the wire is fused if it is fused please contact your dealer for the same model FUSE and exclude internal fault of the terminal before reuse 2 10 Location queries Global Services Platform Website Www gps288 com Chapter I SMS command format Note All
4. Example 896 E 8 After sending command successfully the tracker will return a message config OK Set Current time zone as E8 Note The default time zone is GMT 8 So you need recover it to GMT 0 first with command 896 w 8 Then you can set your time zone accordingly Open GPS Signal Note Center number can send this command to open GPS The tracker will begin to work with GPS signal There is still GPS signal even the tracker is shutdown Format 8 10 After sending command successfully the tracker will return a message config OK Note The default GPS signal state is open Close GPS Signal Note Note Center number can send this command to close GPS The GPS module will stop working and in this mode there will be less power consumption There is still no GPS signal even the tracker is shutdown Format 811 After sending command successfully the tracker will return a message config OK Pre stored numbers Setup Format 711 password phone numberl phone number2 phone number3 phone number4 Note phone no 4 is the voice monitor no and it cannot be the same one as center number or any other pre stored numbers Only this number can do voice monitor For example You want to set four stored numbers 7 11 000000 135678923 14 1389234 1600 13625678900 13625678901 The new numbers will replace the old numbers and it will send confirmation to the sender if the password is right CONFG O
5. GSM GPRS GPS Tracker LDW 103B User Manual Version 1 4 Please read this manual carefully before attempting installation and online activation Pictures are for indication and illustration purposes only Chapter I Preface 1 1 General LDW 103B represents the perfect combination of GSM GPRS and GPS technologies This model with precise dimensions and compact appearance expresses the advanced workmanship in the GSM and GPS field and is the typical design combing communication products and GPS services As a professional security and positioning company we will provide you with more and better products and services Before use please spend several minutes reading this user s manual in order to understand operation details and obtain better services 1 2 Notices 1 Please read carefully this user s manual and always use correct operation methods to prevent any possible errors 2 This user s manual is for reference only If some contents and operation steps are inconsistent with those for the actual product the latter will prevail 3 The defaulted password of this product is 000000 GPS Tracker LDW 103B is a perfect combination of GSM GPRS and GPS Small size and simple appearance are the typical design of the combination of telecommunication products and GPS positioning products Advanced technology and craft in GSM and GPS area are embodied in this product Chapter II About the Device LDW 103B is remote vehicle posi
6. K Note 13625678901 is the voice monitor no only this number can make voice monitor SOS button Emergency call button In case of emergency please press SOS button over 3 seconds center number will receive a call and SMS Note SMS will be sent only when the device is online on the tracking system Device Setup inquiry Format 902 password Example 902 000000 After sending command successfully the tracker will return a message Settings The Main User Is 13689645010 The Auto Alert Is Off Low Battery Alert Is On The Vibrate Warning Is On The Alert Call Is Off The Warning Speed is Off Remote Restart Format 90382 password Example 90382 000000 After sending command successfully the tracker will return a message Config OK The Machine Will Restart Restore factory settings Format HFSZ Example HFSZ After sending command successfully the tracker will return a message Config OK Device Has Been Reset To Factory Setting Chapter IV SMS amp Platform Tracking 4 1MS location inquiry There is no need for Center number to add the password to inquiry Other numbers need to add the password to inquiry 4 1 1 Address tracking Format 666 password For example you send 666 000000 to the tracker you will get a reply SMS as follow SN 886600000525 No 106 Sanlian Road Longhua Town Bao an District Shenzhen China Notes Only when the device is online on the tracking syste
7. MOBILE CCDLEN QIUXIA 2 1 RX0000 APN is CCDLEN the login user name is QIUXIA 21 and login password is Rx0000 Note The default APN of this product is CMNET Server connection Setup Format 803 domain name or IP address port number This command is used to set GPRS center server address which could be fixed IP number After the setup is successful the module will send a reply with config ok the ip server is 59 188 20 67 8545 Example 803 59 188 20 67 8545 Setup via domain name Example 803 www gps288 com 8545 Regular Upload Interval Setup The defaulted factory upload time interval of this device is 10 seconds for getting the point and uploading one point location information The user could change such parameter according to actual demand Format 730 sampling interval The value of sampling interval from 10 seconds to 3600 seconds For example 730 30 Note The parameter 30 indicates getting and uploading one point location information every 30s Vehicle Defense Setup Note You need to open the vehicle defense first then you can use the vibration Alarm or you cannot use vibration Alarm 1 Open vehicle defense Format 911 After sending command successfully the tracker will return a message config OK The Auto Alert Is On 2 Close vehicle defense Format 910 After sending command successfully the tracker will return a message config OK The Auto Alert Is Off
8. e down You must open the GPRS function provided by the terminal SIM If your SIM card has been setup but it requires you to input SIM PIN please close the SIM PIN function under the instruction written in the user manual Make sure the sufficient money to pay for the terminal SIM card charge Check the GPRS network connection with your mobile phone 2 5 2 The selection and installation of the terminal This terminal is a product with GPS polling a kind of high tech product you d better to install it with the help of professional companies or workers authorized by the distributor Please install it according to the following order don t revise it or supply power for the terminal There are two ways to install the terminal hidden installation and open installation Hidden installation is suitable for the application of the terminal in the specialized vehicle While open installation is suitable for the adoption of the terminal in the provisional vehicle 2 5 1 1 The hidden installation should be completed by the professional institution authorized by the distributor 1 To avoid the thief s destruction the terminal should be installed in a hidden place Suggestions are as follow Hidden beneath the decoration board below the front windshield Hidden around the front panel with a surface made of non metal materials Hidden beneath the decoration board under the back windshield 2 don t put the terminal together with the emission s
9. ing off Pull the plug and the terminal will be powering off after cutting off the electricity 2 8 Side key function In normal light conditions press the side button 3S then the current location information will be sent back to the center number 2 9Terminal failure recovery 2 9 1 Disconnecting between terminal and service center Firstly please checks the three lights of terminal if there is no conditions for observation please call the terminal SIM card number using a mobile phone and according to instruction to judge the terminal state e If not connected and suggests that the terminal cannot be connected or temporarily out of service Terminal may not be covered by the GSM signal or in weak for signal such as the basement please drive to some place covered by GSM net e If not connected and suggests insufficient funds of the terminal or shut down please recharge for this SIM card e If it is connected and there is the beep sound Terminal SIM card is installed correctly and has remaining please contact the operator of this SIM card to check whether the card has opened GPRS or you can also use the phone browser enter your favorite Web site to see whether can open the Web page Otherwise it should not open GPRS service please contact network operators to open it for you e If not connected and the terminal has turned off At this point must call vehicle back to check the working status of the terminal dealing
10. m it will send you back this SMS information 4 1 2 Longitude amp latitude tracking Format 888 password For example you send 888 000000 to the tracker you will get a reply SMS with link http map google com q 22 677327N 114 120738E SPEED 000 0 Date 12 05 28 Time 15 52 04 IMEI 353509000924608 Visit the link by your phone or computer you will know the name of the location in detail When there is no GPS signal you will get a repay SMS as follow MCCMNC 460010 LAC dle3 CELLID 2535 4 2 Tracking on platform Please visit www gps288 com or www track188 com for online real time tracking and fleet management For details please refer to our tracking system user manual Notes 1 This non waterproof equipment please be sure to have waterproof bag 2 This equipment has to work with GSM network 3 Please ensure that there are enough expenses in SIM card in order to avoid the inconvenience of using 4 This equipment cannot work in the power failure state and outside the service areas even if the registered users 5 This equipment supports GPS and GSM GPRS double positioning regarding as the same with the GPS positioning results 6 Please use this equipment in the legal areas The consequences of any violation of the law will be undertaken by the users themselves
11. ons the red line connects to the power positive the black line connects to the power negative 2 2 2 Internet Service Center www gps288 com 2 3 Product Features e Individual or fleet GPS polling e Worldwide use e Supports GSM frequencies 850 900 1800 1900MHz e High sensitivity latest technology and the most advanced GPS chip e Can accurately position even if with weak signal Can work effectively in limited space such as the remote and narrow places compact size easy for hiding eLow energy consumption eRemote oil cutoff e Fast signal capturing supports two modes text message polling and GPRS trace tracking e Alarm function Vibration alarm 2 4 Product Specifications 2 4 1 Technical specifications GSM FREQUENCY 850 900 1800 1900MHz GPS CHIPS SIRF 4 GPRS Class 12 TCP IP build in GSM MODULE GPS SENSITIVITY 159dBm GPS ACCURACY 10m 2D RM GSM ACCURACY 50 200m SPEED ACCURACY 0 1m s COLD STATUS 38s WARM STATUS 32s HOT STATUS 2s MAXIMUM ALTITUDE 18000m HIGHEST SPEED 515m s ACCELERATION OF lt 4g GRAVITY SIZE 72 00 L x 38 0 W x17 0 H mm WEIGHT 50g 2 4 2 Others WORKING TEMPERATURE 20 70 C HUMIDITY 20 80 RH VOLTAGE 7 30v DC CURRENT 60mA 12v DC 35mA 24v DC STANDARD AVERAGE lt 80MA CURRENT LED LED indicate GPS GSM working status or other condition 2 4 3 The indication of
12. ources such as the parking radar system alarms and other vehicle carried communication terminals 3 You can fix the terminal with the cable tie or glue it with wide strong sponge double sided tapes 4 As there are GSM and GPS antennae furnished inside the terminal it must make sure the reception side of GSP upward facing the sky besides there is no shelter caused by metal articles Attention If there is a metal insulation or a heating level glued in the windshield it will reduce the efficiency of GPS signal reception and lead to change the installation position of the terminal due to the malfunction of GPS 2 5 1 2 AS for the open installation at first it should glue the soft robber magnet in the fitting picture on the decoration below the front windshield then put the terminal on the magnet and fix it Attention If you have no soft robber magnet please purchase after connect with the distributor CATHODE E LOAD CONTROLED Y REAY 30 87A POWER 12V 85 Installation steps caution the following installation should be made without power supply otherwise it will be dangerous Wire for cutting off oil circuit of the tracker White wire connects relay feet 86 85 feet to 12 V DC postive 87a feet and 30 feet are in series in the supply power circuits 2 6 The cable connection of the terminal 1 The standard power supply is 7V 30V the red line connects to the power positive while the black line connects to
13. the power negative 2 The negative end should connect the ground or the metal alone don t connect with other ground cord 3 After connecting the power cord please pull the power cord plug near the terminal and supply power for it after installation 4 As for the hidden installation the connection cords for the power should be the main power cord provided by the original manufacturer in the fitting pictures the red end connects with the fuse box contains 2A FUSE which can avoid the short circuit and over current 5 As for the open installation the connection cords for the power should be the lighter power cord provided by the original manufacturer in the fitting pictures the lighter which has 2A FUSE can avoid the short circuit and over current Remind Please contact your distributor if you don t have the lighter power cord 2 7 Terminal working 1 Starting up The terminal automatically starts up with power connecting the red indicator on means the power supply normally Working normally the red indicator will keeps on the blue GPS indicator will always bright means GPS polling standy already the green indicator shows GSM connecting successfully 2 Working exception after working for some time the red indicator light flashes blue GPS Light off means that GPS is off or failure GSM indicator not on shows that GSM fails to receive signal please see the troubleshooting method to eliminate the problem 3 Power
14. the setup below can be only made by Center number Super User Setup Set the new center number and new password by SMS through mobile phone If the setup is successful the module will send a reply with Config OK the Main User and Password Is Reset To 13689645010 center no 123456 new password Format CJML SN code new password 6 digits Center number SN code pls checking it with backside of produt Example CJML amp 86600000633 000000 1 3689645010 Note Center number must be a mobile phone number telephone number will not work Center Number Setup Set the center number by SMS through mobile phone If the setup is successful the sender will receive CONFIG OK The main user is 13286689393 from the tracker Format 710 former password new password 6 digits center number For example 71 0 000000 000000 1 368964501 0 Note All alarming information thereafter including SOS low power electronic fence etc will be sent to this number 000000 is the default password APN Access Point Name Setup Set APN by SMS through mobile phone If the setup is successful the sender will receive CONFIG OK from the tracker Format 802 GSM provider name APN Log user name Log password The default APN is CMNET if the APN doesn t have login user name and password it can be set 0 Example 1 802 Chinamobile CMNET 0 0 APN is CMNET no login user name no login password Example 2 802 CHINA
15. tioning device comprising GPS and GSM GPRS modules Based upon the GPS satellite it shall offer you precise positioning information on dynamic conditions The remote vehicle positioning device shall send longitudinal and latitudinal coordinates to the authorized cell phone which can be utilized by you to position and manage your own vehicles 2 1 Major Functions of the Product Vehicle Positioning and Tracking Real time polling and sending back GPS positioning information which contains longitude latitude speed and direction and the vehicle information to the service platform www gps288 com displaying vehicle s real time condition of the vehicles Trace Playback Related information such as the passed trace speed and time and so on of the vehicles in the past period can be replayed Historical Data Backup In the data base vehicle s driving time trace and speed etc can be conserved in one day or more In order to keep the response speed of the data service the system shall automatically transfer the current database into historical database at regular intervals Anti burglary and Anti robbery In case of emergency situation driver can press the SOS button for sending the message to pre set number to ask for help Message Dispatching If necessary the administrator can send messages to the driver s mobile phone to dispatch direct the vehicle 2 2 Components 2 2 1 Built in GPS module and GSM module Instructi
Download Pdf Manuals
Related Search