Home

MELSECWinCPU Module User`s Manual(Hardware

1. The remaining current capacity is used as a criterion O 1A to less than 3A The system can grow A OA to less than 1A The configuration is acceptable but not expandable x Less than OA The configuration is not acceptable 1 Excluding the consumption current in the USB peripherals 2 The system can be configured by using a Q64PN instead Configuration with many I O modules and intelligent function modules If the total current consumption by the modules on the main base unit including this product and peripheral devices exceeds the power capacity used move I O modules and intelligent function modules to an expansion module The total current consumption by the modules on each base unit must not exceed the power capacity If the system configuration is short of power capacity even with one expansion base unit added add more than one expansion base unit 86 7 Reset Specifications 7 Reset Specifications This product has following kind of a reset The range to be reset depends on system configuration and the condition of DIP swiches Reset Specifications Single CPU Multiple CPU configuration Modules No 2 4 Reset type configuration 1st station SW 5 of DIP switch 2 is SW 5 of DIP switch 2 is OFF ON 1 1 Reset by power OFF to ON Reset by OS rebooting Reset of 1st station Only on multiple configuration CPU Reset by a toggle switch O A MELSECWinCPU module and all the m
2. 1 Move ENTER Accept ESC Abort On Chip Serial ATA Disabled On Chip Serial ATA Enabled Select On Chip Serial ATA Selecting Disabled SATA controller becomes disabled Selecting Enabled SATA works in the legacy mode 1 Move ENTER Accept ESC Abort 44 4 BIOS Setup Onboard Device Phoenix AwardBIOS CMOS Setup Utility Onboard Device Onboard LAN A Enabled Onboard LAN B Enabled t lt Move Enter Select PU PD Value F10 Save ESC Exit Fi General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 4 9 Onboard Device Table 4 9 Onboard Device select Enabled Disabled Onboard LAN A Select Disabled Enabled of Onboard LAN A Onboard LAN B Select Disabled Enabled of Onboard LAN B 1 1 Move ENTER Accept ESC Abort 45 4 BIOS Setup Super IO Device Phoenix AwardBIOS CMOS Setup Utility SuperlO Device Onboard Serial Port 3F8 1R04 t 1 lt Move Enter Select PU PD Value F10 Save ESC Exit Fi General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 4 10 SuperIO Device Table 4 10 Super I O device select Description Onboard Serial Port Disabled 3F8 1RQ4 Onboard Serial Port 2F8 1RQ3 3E8 1RQ4 Select Onboard Serial Port 2E8 1RQ3 Select the address and the IRQ to use of a serial port 1 Move ENTER Accept ESC Abort 46 4 BIOS Setup USB Device Setting Phoenix Awar
3. This prevents an unauthorized person from changing any part of your system configuration Additionally when a password is enabled you can also require the BIOS to request a password every time your system is rebooted This would prevent unauthorized use of your computer You determine when the password is required within the BIOS Features Setup Menu and its Security option If the Security option is set to System the password will be required both at boot and at entry to Setup If set to Setup prompting only occurs when trying to enter Setup 60 4 BIOS Setup Exit Selecting Save amp Exit Setup Pressing lt Enter gt on this item asks for confirmation Save to CMOS and EXIT Y N Y Pressing Y stores the selections made in the menus in CMOS a special section of memory that stays on after you turn your system off The next time you boot your computer the BIOS configures your system according to the Setup selections stored in CMOS After saving the values the system is restarted again Exit Without Saving Pressing lt Enter gt on this item asks for confirmation Quit without saving Y N Y This allows you to exit Setup without storing in CMOS any change The previous selections remain in effect This exits the Setup utility and restarts your computer POST Messages During the Power On Self Test POST if the BIOS detects an error requiring you to fix something it will either sound a beep code or dis
4. 31 bytes 16 bytes 16 bytes 8 bytes 1 byte MI speaker controller 8 bytes 8 bytes 2 bytes 2 bytes 8 bytes 4 bytes 16 bytes 6 bytes 12 bytes 32 bytes 1 byte Primary IDE 8 bytes 2 bytes 8 bytes 4 bytes 1 byte 12287 bytes 16 byte 16 byte 16 byte 128 byte 64 byte 100 10 Appendix Interrupt Level List Table 10 2 Hardware Interrupt Levels Factory Settings om mn voonckorwor om Figo master o timo om imo roce ma 1 Jinterrupe controler lava oan Pies stave 1 fReartimeciock rn ma gt systemreserved ma beiemmame I ma System reserved a a u mwas gt II feom ET Pa o e mas 1 fma rm Cras master system reseve om mwa gt JT Previa port con oon Pins gt 1 irse reserved om Pings gt irte reserved om mar gt tow finan renova om The interruption list is one when APIC is not used APIC is used on Windows so the interruption of PCI devices is assigned behind IRQ16 101 10 Appendix Appendix 2 Battery Battery Specification This product uses the following battery Type Lithium primary battery Model BR 12AA Maker Panasonic Nominal voltage 3V Nominal capacity 1000mAh Lithium content 1g or less A CAUTION You should treat 1t according to exportation regulations when you export the product with the battery including lithium When we ship it we packaged it accor
5. Disable DVMT Mode Enable Select Disabled Enabled of DVMT Dynamic Video Memory Technology Mode 1 Move ENTER Accept ESC Abort Total GFX Memory Total GFX Memory Select Total GFX Memory Select the total memory size of graphics 1 Move ENTER Accept ESC Abort 41 4 BIOS Setup Integrated Peripherals This section sets configurations for your hard disk and other integrated peripherals The first screen shows four main items for user to select Once an item is selected a submenu appears Details follow Phoenix AwardBIOS CMOS Setup Utility Integrated peripherals OnChip IDE Device Press Enter Onboard Device Press Enter SuperlO Device Press Enter USB Device Setting Press Enter t lt Move Enter Select PU PD Value Fi0 Save ESC Exit Fi General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 4 7 Integrated Peripherals 42 4 BIOS Setup OnChip IDE Device Phoenix AwardBIOS CMOS Setup Utility OnChip IDE Device On Chip Serial ATA Setting SATA Mode IDE On Chip Serial ATA Enabled 1 lt Move Enter Select PU PD Value F10 Save ESC Exit Fi General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 4 8 On Chip IDE Device 43 4 BIOS Setup On Chip Serial ATA Setting Table 4 8 On Chip Serial ATA Setting select SATA Mode SATA Mode Select SATA Mode Only IDE is supported
6. Pr cautionss 22 5 ches tei et oe eae ee a ie 7 Transport Precauciones te 7 EMC Precautonse en iaa 7 CONDITIONS OF USE FOR THE PRODUCT ne han 8 Packing last aa leandra doit beat ae tied 9 Table of Contents es ee een nee ee ray Br 11 L Introduction 14 Abo tthe Produttore td 14 RR RAN 14 B lt MO re A ee ee 14 2 System Reference 15 Specificato Reese eee ee nee nee pee eee eee re ee a mere 15 External Dimensions ee ae ee teaver ame ee Ss 17 3 Hardware Setup 18 Before Using the Product for the First Time ususssseeessseessnsessnnenennnennnnnnennnnennenenenennenensnennnn 18 Installing th Modulen 242 abend 19 Uninstalling the Mod le isinen iniettori essiri nae ae in 20 Installing the fitting tx a CP Card 2 1 2 9 nenne EI la 20 The hole to attach the binding tie 0 0 eececesceeseceesneeeessecesseeeecsseeceeeecesseeecesseeessaeeeeeeeeesesessaeeenas 21 4 BIOS Setup 22 BIOS SUP io ten nes shsne benennen enan a n e nsaan ene ea gps a e aeaa eE e TAE thee 22 TEO A aie ees 22 LAU A o a a e ee o e eet 22 Using Setup 22 2222 Se a as tenets 23 Getting CI need zes o 23 Hi ASC OF Problems A 23 A Einal Note About Setup2 2 2 Sette whieh Sara eevee i aes 23 Man Men an A le est Cav eee 24 Setup Items ern NO 24 Standard CMOS Features cccccccnnnnncncnononononnnanonncnnncnnnnnnnnnnonnnnnononnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnos 26 Main Menu Selections2 22 amp 22222 ee ee ee a 27 IDE
7. Removable CDROM Hard Disk Enabled On Fast Typematic rate Setting Disabled x Typematic Rate chars Sec amp x Typematic Dealy Msec 250 Security Option Setup xX APIC Mode Enahl ed MPS Version Control For OS 1 4 BEEP Voice Enabled WDT Protect Disabled POST Code Show Disabled CF Backup Press Enter t lt Move Enter Select PU PD Value Fi0 Save ESC Exit F1 General Help F5 Previous Values FG Fail Safe Defaults F7 Optimized Defaults 4 Following message will be shown Press Y key DISK BACKUP Start BACKUP Y N I N Reboot 5 Connected drives will be shown as follows Select built in SSD for OS as Source Disk In the following figure 4GB NANDrive SSD and MITSUBISHI ELECRIC CF card are connected For backup press A key and select SSD as Source Disk Now Connect Disk Select Source Disk A 4GB NANDRIVE B MITSUBISHI ELECTRIC 105 10 Appendix 6 Next select the CF card for backup A or B key as Destination Disk In the following figure only B is selectable as Destination Disk Now Connect Disk Select Destination Disk B MITSUBISHI ELECTRIC 7 Next the following message will be shown If you want to verify data when copying press Y key Need Verify Y N 8 Copy procesure will start DISK BACKUP 0000AB00 006CFDOO0O Sectors 9 The following message will be shown after copy procedure has
8. 1 Move ENTER Accept ESC Abort 30 4 BIOS Setup Limit CPUID MaxVal Disabled Limit CPUID MaxVal Enabled Select Disabled Enabled of Limit CPUID Maxval For older OS such as Windows 98 and Me select Enabled If not the maximum value of CPUID can not be hundled 1 Move ENTER Accept ESC Abort Auto Disabled C1E Function Select C1E Function 1 Move ENTER Accept ESC Abort CPU C State Capability Disable CPU C State Capability C2 C4 Select CPU C State Capability Selecting any values other than Disabled can reduce the power consumption when CPU idles Execute Disable Bit Enabled Select Enabled Disabled of Execute Disable Bit Disabled Selecting Disabled makes XD function flag to be 0 by force H Move ENTER Accept ESC Abort 31 4 BIOS Setup Hard Disk Boot Priority With the field there is the option to choose aside from the hard disks connected Bootable add in Cards which refers to other external device Phoenix AwardBlOS CMOS Setup Utility Hard Disk Boot Priority 1 Bootable Addin Cards Menu Level gt Use lt gt or gt to select a device then press lt gt to move it up or lt gt to move it down the list Press lt ESC gt to exit this menu gt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 4 5 Hard Disk Bo
9. Component Function 62 Component Name eisila roto o road oie Eriein E EEr E EEEE AE EE a a 62 Each Component FUunction ccccccsccccssscesseceesseecessneeeesseeeeeeecesseeceseeeseeceeeeessseeeseeesesseeeeseeensaeeengs 64 CF card connector CF CARD cecccceccccssssceeseeeessecesseseeeeeeeeeseeceaececesesesseeeesesesseeecesseeesaeees 64 O A nate naires tess ES 65 Giga bit Ethernet LAN A B uo eccccccccccesseceessecesseeeeeseeessseeessesecesaecenseeeeseeessseeecesseeesaeeenseees 66 LED Displays see RE tenes ett EE 67 Terminal block OF nennt dal genen abe ees 68 Serial Port Interface SERIAL cusseseesssneeesnessnnennsnnnenennennnnnnnnnnennnnnennnnneennnnnensnenensnennnn 70 CRT Interface A RGB ic 71 USB PO N E EEE sdaedebesidlesundess cdberiademaaiyartes 72 Control With Ae 72 6 Combination with the MELSEC Q Series 75 DO A AA a A le 75 System Con UM er O e Fees A ns 75 ACCESS FON Se meaa ee santas bessere Dialer see A A OO 81 Multiple CPU Configuration e a A a a ees 82 CPU Configuration Diagrams Hanna RI ae 84 Notes ar Rn eaten eee el le een re Wass eee aA Aes 85 7 Reset Specifications 87 Reset Specificationsu u amp 220re aia 87 Reset Procedure of a MELSECWinCPU module and All the Modules on a Bus 88 Reset Procedure of Bus Interface Driver and All the Modules on a BUS ssccseceeeseeeseeeseeesneeeneeees 89 8 Troubleshooting 90 Laps tor Better Troubleshooting au een 90 Th
10. First start up Windows then make sure the condition of EWF from command prompt If it is Disabled set it to Enabled 2 Shutdown Windows Then turn power off 3 Set the 4 switch of DIP switch 1 to ON How to set the DIP switch for write protect from ON to OFF 1 Turn power off 2 Set the 4 switch of DIP switch 1 to OFF 3 If you want to turn EWF off start up Windows set EWF to Disabled from command prompt then reboot OS 1 In order to know how to set EWF refer to Notes on Windows Embedded Standard which is packed with this product SSD Enable switch The 3 swich of DIP switch 1 can change the condition of built in SSD to Enabled Disabled Set this swich to ON if your application or system requires it or you want to make SSD unrecognizable to the OS and BIOS 65 5 Each Component Function Giga bit Ethernet LAN A B This product is equipped with 2 ports for giga bit Network type 1000BASE T 100BASE TX 10BASE T Transmission speed 1000M 100M 10M bps Max network path length 100m segment Controller Intel 82574L Table 5 3 1 Ethernet Connector aia PIN 100BASE TX TX 1000BASE T ls mw IE EA EA Ec o ll Llao ne moo RX TRD 1 TRD 3 LEDs for display of network statuses Right LED Link LED Normal connection Green ON Operation Green Blinking Left LED Operation LED 10M Off 100M Green 1
11. Mitsubishi shall not be liable for compensation of damages caused by any cause found not to be the responsibility of Mitsubishi loss in opportunity lost profits incurred to the user by failures of Mitsubishi products special damages and secondary damages whether foreseeable or not compensation for accidents and compensation for damages to products other than Mitsubishi products replacement by the user maintenance of on site equipment start up test run and other tasks 5 Changes in product specifications The specifications given in the catalogs manuals or technical documents are subject to change without prior notice 6 After service When you request the investigation of failure make sure that we may be unable to investigate some parts of the product The major difference of after service from MELSEC Q series etc 1 The warranty period is year after we deliveried it or 18 monthes after the production whichever come first 2 The repairable period after the end of mass production is 6 years after the end 3 The support may take long times according to the content and the timing of your requests That s all 109 MELSECWinCPU Module User s Manual Hardware Design Function Explanation MODEL Q10WCPU W1 U HK E MODEL 13JZ68 SH NA 081055ENG A 1112 KWIX afa MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 a NAGOYA WORK
12. Name Manual No Type Code MELSECWinCPU Module Q Bus Interface Driver User s Manual Utility Operation Programming MELSECWinCPU Module User s Manual Hardware Design Function Explanation 2 SW1PNC WCPU B has been installed to the main body SH 081054ENG 13JZ67 SH 081055ENG 13JZ68 3 It is attached to the main body Do not turn on power of the product without a CF card Configuration Royalty Royalty Royalty t consent consent contract contract 9 contract Recovery soft SWIPNC WCPU B S gt i OS g Fittings and Main bod screws to ain ody fixa CF card Royalty consent Royalty consent Royalty consent contract contract OS contract Recovery soft SW1PNC WCPU B n a Notes on Precaution List Product Guide Windows Yoo Embedded Connector for terminal block Coonector Connector cover for RGB cover for SERIAL Standard po ixi Notes on Windows Fixing bandage Product Guide Embedded Standard Precaution List 7 C Setup Procedure Recovery E a Procedure O Y Sind Connector Connector e Setup Recovery cover for LAN cover for USB Recovery Media SW1PNC WCPU B Procedure Procedure An CAUTION 1 2 3 4 5 6 When turning off the power of the standard base plane or the additional base plane complete the shutdown of OS before turning power off If the power is turned off while the OS
13. as a blank slot cn All points becomes OFF Other combination No errors happen but not work in order Intelligent Interruption Input module High speed input module T O mixing module Input High speed input Blank slot All modules e The last I O No On I O assignment settings make sure that the last I O No becomes less than OFFFH If you set I O assignment so that the last I O No exceeds OFFFH intelligent function module assignment error error code 2124 SP UNIT LAY ERR happens 79 6 Combination with the MELSEC Q Series 2 Notes when a MELSECWinCPU module automatically assigns the first XY If the first XY was not set to an I O assignment setting a MELSECWinCPU module automatically assigns the first XY Therefore the first XY setting of each slot may conflict with the one which MELSECWinCPU module assigned in the following cases a and b a On the first XY setting you have swapped the front I O No with the rear one b There exist both the slot which you assign the first XY to and the slot which you did not do so the slot MELSECWinCPU module automatically assigns Refer to the example of the clash of the first XY as follows Af MELSECWinCPU setting utility Module information Module monitor Online operation System setting 1 0 assignment setting Multiple CPU setting Target setting Communication diagnostics 1 0 assignment zu
14. by setting the shutdown command input to OFF and turning the power ON again The EXIT LED comes on only when you shut down Windows or hardware reset If you reset this product or restart the OS in the multiple CPU configuration other CPUs detect a multiple CPU down error While a MELSECWinCPU module is doing a shutdown procedure EXIT LED is lighting the condition of the main station becomes resetting or CPU DOWN If you reset the 1 station while SW 5 of DIP switch 2 is ON using multiple CPU configuration a MELSECWinCPU module will also be reset and becomes the condition without any power If you did so while OS is working it means that you finished the system without a shutdown procedure and OS may not work in order after the next reboot After you turn off power supply to this product wait for more than 5 seconds till the next power ON 88 7 Reset Specifications Reset Procedure of Bus Interface Driver and All the Modules on a Bus Single CPU configuration with this product as only one CPU Module 1 Stop the user application 2 Set the toggle switch to B RST hold the switch at the B RST position for two seconds then release it 3 Set the toggle switch to B RUN 4 Execute the user application Multiple CPU configuration DIP switch 2 with SW 5 set to OFF 1 Stop the user application 2 Reset CPU Module No 1 3 Execute the user application An CAUTION In the multiple CPU configuration re
15. hold its data Do not change the default value of factory settings T Move ENTER Accept ESC Abort Precharge delay tRAS Precharge delay tRAS Select Precharge delay tRAS Select the number of DRAM clock for the precharge delay time A AA A A A A u Do not change the default value of factory settings 15 t 1 Move ENTER Accept ESC Abort 39 4 BIOS Setup System Memory Frequency System Memory Frequency Select System Memory Frequency Select the frequency of main memory Do not change the default value of factory settings 1 Move ENTER Accept ESC Abort System BIOS Cacheable Disabled Select Disabled Enabled of System BIOS Cacheable Enabled Selecting Enabled allows caching of the system BIOS ROM at F0000h FFFFFh resulting in better system performance However if any program writes to this memory area a system error may happen Do not change the default value of factory settings tJ Move ENTER Accept ESC Abort Memory Hole At 15M 16M Disabled a Memory Hole At 15M 16M Enabled Select Disabled Enabled of Memory Hole At 15M 16M Do not change the default value of factory settings ty Move ENTER Accept ESC Abort 40 4 BIOS Setup VGA Setting The field under the On Chip VGA Setting and their defaults settings are Table 4 7 VGA Setting select OnChip Frame Buffer Size On Chip Frame Buffer Size Select the size of writing buffer between CPU and PCI
16. is working the OS may be out of order at the next and later boot In order to protect the modules from an unexpected power failure we recommend to connect UPS to your system This document in whole or in part may not be reproduced without permission This document is subject to change without notice at any time While we are doing our best to ensure this document has no error should you have any questions or find any ommissions or similar consult the distributor Regardless of the foregoing statement we assume no responsibility for any errors that may appear in this document or for results obtained by the user as a result of using this product Intel Intel Atom Intel Core and Celeron are registered trademarks of Intel Corporation Microsoft and Windows are trademarks of Microsoft Corporation MELSEC CC Link are trademarks of Mitsubishi Electric Corporation Other brand and product names are trademarks of their respective holder 10 Table of Contents Precautions regarding Warranty cccccccessccssssceesseecesseeeessecesssecesseeeeeeecessesesseseeesseeeesseeeeseeeseesessaes 1 Safety Preciado e eto o ot ia 2 Handli e A eka ata Ok 2228 ee eet eae WU se as hae 3 Desire Precautions O rn hn a de eee eee a nd e a 4 Installation precautions e dudo O na 5 Winna precautions ee N ao a Ln online 6 Power Supply and Maintenance Precautions cccccecessceceeseceesseeeeseceeseeeceseeesseeeeeseeeessesensees 6 Disposal
17. may result in a fault malfunction injury or fire Before attaching or detaching the Module be sure to turn the external power supply off for all phases Failure to turn it off for all phases may cause the Module to fail or malfunction Disposal Precautions An CAUTION When disposing of the product treat it as industrial waste When disposing of a used battery trash it separately under the relevant laws For details of battery regulations of EU refer to Appendix 3 Disposal of Battery Transport Precautions AN CAUTION When you transport batteries with lithium you should treat them according to transport regulations For details of transport regulations refer to Appendix 2 Battery EMC Precautions Regarding EMC Instruction Class A Notice 1 The ferrite core must be installed in each of the following cables so that this product may fit the above mentioned standard Refer to the following for the model of ferrite core Equivalent goods are also availabele USB A B C D E E04SR200935A SEIWA SERIAL E04SR200935A SEIWA E04SR200935A SEIWA E04SR241331A SEIWA Image diagram Ferrite core eee Cable Turn 1 2 The shield of cables connected to USB and I O port should be connected to FG nearby the main body CONDITIONS OF USE FOR THE PRODUCT 1 2 Mitsubishi programmable controller the PRODUCT shall be used in conditions i where any problem fau
18. set on GX Configurator QP on a positioning module under the control of MELSECWinCPU module You should use bus interface function QBF_ToBuF and write each parameter in the buffer memory of a positioning module TT 6 Combination with the MELSEC Q Series 4 Note on using serial communication module Only the communication by the protocols with no procedure is suppored on a serial communication module under the control of MELSECWinCPU module a Following function is not available MC protocol and bi directional protocol are not available Serial communication module special commands are not available Watch function for programmable controller CPU is not available Modem function is not available b When using interrupt program follow the procedure below Select interrupt event No on lt lt System Setting gt gt tab of MELSECWinCPU setting utility Write 1 in the buffer memory address 2010H 2110H of a serial communication module In your program make the procedures where it receives the interrupt event using QBF_WaitUnitEvent function and runs the proper process 5 Note on using FL net module FL net module under the control of MELSECWinCPU module has following limitation In your program make the procedures where it receives the interrupt event using QBF WaitUnitEvent function and runs the proper process Automatic refresh function is not available 6 Note on using GX Configurator By using MELSECW
19. 0 C 122 Select CPU Warning Temperature 53C 12T 56 C 133 60 C 140 temperature warning 63 C 145 You can select the threshold temperature of CPU If it exceeds the specified temperature a beep will sound as 66 C 151 70 C 158 1 Move ENTER Accept ESC Abort a warning 58 4 BIOS Setup Frequency Voltage Control Phoenix AwardBlOS CMOS Setup Utility Frequency Voltage Control Menu Level gt 12 Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 4 16 Frequency Voltage Control Table 4 16 Frequency Voltage Control Selections Description Spread Spectrum Disabled Enabled Spread Spectrum Select Disabled Enabled of Spread Spectrum When the system clock generator pulses the extreme values of the pulse generate excess EMI Selecting Enabled changes the extreme values from spikes to flat curves thus reducing EMI This benefit may in some cases be outweighed by problems with timing critical devices t Move ENTER Accept ESC Abort 59 4 BIOS Setup Defaults Menu Selecting Defaults from the main menu shows you two options which are described below Load Fail Safe Defaults When you press lt Enter gt on this item you get a confirmation dialog box with a message similar to Load Fail Safe Defaults Y N N Pressing Y loads the BIOS default values for the most s
20. 000M Orange LAN drivers Installed 66 5 Each Component Function LED Displays Table 5 4 LED Displays Abbreviat ae BS Name Color Status Definition ion On The hardware is all set to go Gren The hardware is not ready or a system WDT error has occurred READY EM EN reset by the reset switch has been accepted in The hardware is reset two seconds after the LED starts blinking The bus interface driver is running BUS User applications have been enabled for bus access B RUN Green UF DRIVER RUN The bus interface driver has been suspended The Y output is off User applications have been disabled for bus access The bus interface driver has accepted a reset generated either by setting Blink the toggle switch to B RST or by resetting module No 1 in the multiple CPU configuration EN A system error has occurred without stopping the output Sn En Thi duct th 1 stat s product is e normal state ERROR is product is in norm Blink A system error has occurred while stopping the output EF A AA AAA A E EEN Br This product is in the normal state eon Grauer This product has caused an internal battery error ALARM Po This product is in the normal state disen The shutdown and hardware reset procedure has been completed 2 Cor The shutdown and hardware reset procedure has not been completed Grasi Access is being made to IDE built in SSD a CF card ACCESS Access is not being made to IDE built i
21. 5 Assignment Devices s using this INT Reserved INT Pin 6 Assignment Select INT Pin 6 Assingment Devices s using this INT USB 1 0 1 1 UHCI Controller Bus 0 Dev 26 Func 1 t Move ENTER Accept ESC Abort 56 4 BIOS Setup INT Pin 7 Assignment INT Pin 7 Assignment Select INT Pin 7 Assingment Devices s using this INT Reserved INT Pin 8 Assignment Select INT Pin 8 Assignment Devices s using this INT USB 1 0 1 1 UHCI Controller Bus 0 Dev 29 Func 0 USB 2 0 EHCI Controller Bus 0 Dev 29 Func 7 ttMove ENTER Accept ESC Abort 57 4 BIOS Setup PC Health Status The BIOS shows the PC health status in this window Phoenix AwardBlOS CMOS Setup Utility PC Health Status CPU THRM Throttling Disabled CPU Warning Temperature Disabled Current System Temp 52 C 125 F Current CPU1 Temperature 67 C 152 F Vcore 0 84V 1 8V 76V 5V 91V 3 3V 34V 1 05V 06V VBAT V 10V t lt Move Enter Select PU PD Value F10 Save ESC Exit Fi General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 4 15 PC Health Status Table4 15 PC Health Status CPU THRM Throttling When the temperature exceeds the value set in CPU Waning Temperature below the throttling is activated in selected percentages to restrain the heat generation from CPU Note that the operation in Windows is not supported CPU Warning Temperature Disabled 5
22. Adapters ii poda 28 Advanced BIOS Features Setup cccccccccssccssssecessnecesseecesseeesseeceseeessaeesessesessaeseeseeeesseseneeeeesaeeees 29 CPU Features Re cate cabsects L a E aes 30 Hard Disk Boot Priority 2 2 2 annie el nN eGR Ae ea ela 32 Virus WANN ernennen leere agen dens eed li 32 Advanced Chipset Features Setup cccccccscccssssecessseceeseccesnecesseseeeseeeeeseecessesesaeeeeseeeeeeeeeessesensaeees 38 a 41 Integrated Periphetalsm cia a ao a o e N a a ad 42 OnChip IDE Device E E EE E e eee 43 On Chip Serial ALAS ad A Dd 44 Onboard Devices kenn Oy rr PO OI vpn MIN go Ten 45 Super 1O DEVIEE 84000 Renata esti cits be old id dae eee 46 WSBuDevice Setung 2 22 22 1 A Ml E id 47 Power Management Setup ccccssssccccsssneceesseesneeceessneeceessesnneceessseeeessseeeeeseneeeeseeeeeeeeeseeneeeeenags 49 PnP PEI Configuration Setup ren esheets lan rein ees eta ets eee 53 TRO MAR CSOULCES Oia 54 BC Health SONS reellen 58 Frequency Voltage Control ueesesesssseessneeesnnennennnenennneennnennnnennnnnennnnennnnnneennnnennnsneennnsnensnanensn nenne 59 Defaults Meilen aes Oa AT 60 Supervisor User Password Setting uueseessssesssnsneessnnssnnenennnennnnenennnnennnnennnnnennsnneensnnneensneensnennsnen 60 Ext A A O oad AeA 61 POST MESSI A i a 61 POSEBESP A a ee OF eben wee ee 61 Position and Setting of CMOS ROM clear SWitCh cooooccconoccnonocncnoncncnonnoncnnnnonononcnnannncnoncncnonnnnnna 61 5 Each
23. Baseunit Q33B Q35B Q38B Q312B Q38DB Q312DB Q63B Q65B Q68B Q612B Power supply module 6 7 Q61P Q63P Q64PN Q61P D Q series modules are available For details refer to the manual of each module DC A High speed input module QX40H QX70H QX80H QX90H TRIA 3 Bat l modules are available jean For details refer to the manual of each module output mixing module D A conversion module Q62DAN Q64DAN Q68DAVN Q68DAIN 64AD2DA 61LD D62 QD62D QD62E QD63P6 QD6AD2 QD75P1 2 QD75P2 2 QD75P4 2 QD75D1 2 QD75D2 2 QD75D4 2 Positioning module 5 QD70P4 2 QD70P8 2 QD75M1 QD75M2 QD75M4 QD75MH1 QD75MH2 QD75MH4 QD74MH8 QD74MH 16 QD72P3C3 QD70D4 QD70D8 Temperature control module 2 Q64TCTT Q64TCRT Q64TCTTBW Q64TCRTBW ee Conversion 1Q64TD 2 Q64TDV GH Q64RD G Q68RD3 G Q68TD G H01 Q68TD G H02 module Temperature input module 64RD 2 Pulse input module with insulated QD60P8 G channels Runs conversion module with Q6SAD G Q64AD GH Q62AD DGH insulated channels DA conversion module with Q66DA G Q62DA FG insulated channels 66AD DG Loop control module a62HLC Interrupt module QI60 QX40H QX70H QX80H QX90H IMELSECNET H module QJ71LP21 25 QJ71LP218 25 QJ71LP21G QJ71BR11 2 QJ71LP21GE J61BT11N J61CL12 2 A QJ71FL71 T QJ71FL71 B5 QJ71FL71 B2 2 e AS QJ71FL71 T F01 QJ71FL71 B5 F01 QJ71FL71 B2 F01 2 AS i master module 2 QJ71AS92 Serial communication module 5 Q
24. Consult your local system NO service desk or agency of Consult your local system Mitsubishi Electric service desk or agency of Corporation End Mitsubishi Electric Corporation Any driver message in the management tool Event Viewer YES Check settings according to the details about the error YES Any error information displayed about MELSECWinCPU module settings Check settings according to the details about the error Consult your local system service desk or agency of Mitsubishi Electric Corporation 94 8 Troubleshooting BIOS Error One or more of the following messages may be displayed if the BIOS detects an error during the POST If the items not described below apperar frequently the product should be repaired CMOS battery has failed CMOS battery is no longer functional It should be replaced Refer to Appendix 2 Battery about the exchange of a battery Error encountered initializing hard drive CF card or SSD cannot be initialized If you installed a CF card check if it is installed properly Error initializing hard disk controller Cannot initialize a controller Keyboard error or no keyboard present Cannot initialize the keyboard Make sure the keyboard is attached correctly and no keys are being pressed during the boot If you are purposely configuring the system without a keyboard set the error halt condition in Setup to HALT ON ALL BUT KEYBOARD or NO ERROR
25. Device Second Boot Device Third Boot Device Boot Ohter Device Boot Up NumLock Status Gate A20 Option Typematic Rate Setting x Typematic Rate Chars Sec x Typematic Delay Msec Security Option x APIC Mode MPS Version Control For OS BEEP Voice WDT Protect POST Code Show CF Backup Press Enter Press Enter Disabled Enabled Enabled Disabled Enabled Disabled Removable CDROM Hard Disk Enabled 0n Fast Disabled 6 250 Setup Enabled 1 4 Enabled Disabled Disabled Press Enter t lt Move Enter Select PU PD Value F10 Save ESC Exit Fi General Help F5 Previous Values FG Fail Safe Defaults F7 Optimized Defaults Figure 4 3 Advanced BIOS Features Setup 29 4 BIOS Setup CPU Feature Press lt Enter gt to configure the settings relevant to CPU Feature Phoenix AwardBIOS CMOS Setup Utility CPU Feature PPM Mode Native Mode Limit CPUID Maxval Disabled CIE Function Disabled CPU C State Capability Disable Execute Disable Bit Enabled t lt Move Enter Select PU PD Value F10 Save ESC Exit Fi General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 4 4 CPU Feature Table 4 4 CPU Features select PPM Mode PPM Mode Native Mode SMM Mode Select PPM Mode When using OS which supports ACPI select Native Mode When using elder OS such as Windows 98 and Me select SMM Mode
26. Green CF Card Slot ae 3 position toggle switch 1 0 1000 AOON LANA LNK CHB LNK Bottom Front DIP switch 1 Puss lt HOLIMS did gt DIP switch 2 3 Al _ Back l 2 l Figure 5 1 Component Name 62 5 Each Component Function Table 5 1 Each Component Function Indicates system error 63 5 Each Component Function Each Component Function CF card connector CF CARD A CF card connector supports a CF card Type I memory card only Table 5 2 CF card connector Connector used 50 pin header type 1 27mm pitch Pin No 50 Signal name Direction Pin No Signal name Direction GND DD3 VO N C VO Q Z oO Q Z oO Q Z oO Q Z oO a lt y Z oO Z oO DD4 VO DD5 VO VO VO Output DD11 CD3 5V INTRQ 5V VO VO VO VO Output Output Output Input Output Q JQ Q Z oO Q Z oO 40 CSEL N C RESET IOCHRDY 43 Output Input Input D o 1 2 B CAR Eon o 14 15 18 19 Eee e N ID w ID y bo n 44 45 DDRQ DDACK DACT DALE Output Output Output bo A ol Z Z a la 64 5 Each Component Function An CAUTION The CF card c
27. J71C24N QJ71C24N R2 QJ71C24N R4 DeviceNet module J71DN91 MELSEC Q Series units are manufactured by Mitsubishi Electric Corporation C input module speed input module C output module sistor output module put transistor 2 Use the product with later function than version B 3 It is the case where you turn off the function switch SW2 and change it to an interrupt unit 4 Following MELSECNET H unit is not available Classification MELSECNET H remote I O station QJT2LP25 25 QJ72LP25G QJ72BR15 QJ72LP25GE MELSECNET H twist bus type QJ71NT11B 5 Some functions have limitation Refer to Note on using I O unit and intelligent function unit 6 Take care so that total current consumption of the whole system would not exceed DC5V reted output current of a power supply unit 7 Q10WCPU W1 series are to be powered by limited Voltage Current LVLC circuit of Listed Power Supplies 76 6 Combination with the MELSEC Q Series An CAUTION If you operate the system whose total current consumption exceeds DCSV rated output current there is a case where system reset occurs and a file will be damaged during operation of MELSECWinCPU Note on using I O module and intelligent function module 1 Note on using MELSECNET H module MELSECNET H module under the control of MELSECWinCPU module has following limitation a It does not support Remote I O network Only PLC to PLC network is available b It
28. MELSECWinCPU Module MITSUBISHI User s Manual Hardware Design Function Explanation Powered by CONTEC This product was jointly developed and manufactured by Mitsubishi and CONTEC Corporation Note that the warranty on this product differs from that on other programmable controller products Refer to WARRANTY in this manual Mitsubishi Programmable Controller NELSEG amp Q10WCPU W1 E Q10WCPU W1 CFE SW1PNC WCPU B Precautions regarding Warranty This product was jointly developed and manufactured by Mitsubishi and CONTEC For a warranty and specifications pay attention to the following remarks Note that there are some precautions regarding warranty and specifications of the product lt Warranty gt po QUOWCPUWI_ MBLSEC Qseries A warranty term without 12 months after the delivery or 36 months after the delivery or charge 18 months after the production 42 months after the production Onerous repair term after ar 7 years discontinuation of production Cr y It may take some time to respond to the problem or repair the product depending on the condition and timing Safety Precautions Read the following carefully before using this product For the use of this product read this manual and relative manuals introduced in this document carefully Then take enough care of the safety and keep the right procedures These safety precautions are limited to this product For program
29. PU_ er To o o E E Toif s High performance model aos ee A AA A AA Universal model QCPU QOOUCPU QO1UCPU QO2UCPU QOSUDCPU QO4UDHCPU QO6UDHCPU Q10UDHCPU Q13UDHCPU Q20UDHCPU Q26UDHCPU QO3UDECPU QO4UDEHCPU QO6UDEHCPU QIOUDEHCPU 013UDEHCPU Q20UDEHCPU Q26UDEHCPU QSOUDEHCPU Q100UDEHCPU The combination is impossible 82 6 Combination with the MELSEC Q Series Multiple CPU high speed main base unit Q30DB Number in which CPU module since Module No 2 can be installed Universal model QCPU Motion CPU QOOUCPU QO3UDCPU Q172CPUN 0172DCPU QO1UCPU QO4UDHCPU Q173CPUN 0173DCPU QO2UCPU QO6UDHCPU Q172CPUN T Q10UDHCPU Q173CPUN T Q13UDHCPU Q172HCPU ee aximum Q20UDHCPU Q173HCPU umber at High Q26UDHCPU Q172HCPU T MELSEC modules to be Module Noe Jertarmarids oauneopu Process ai73Hopu T WinCPU installed model QCPU Q04UDEHCPU module Module No 1 QO6UDEHCPU is contained Q1OUDEHCPU Q13UDEHCPU Q20UDEHCPU Q26UDEHCPU Q50UDEHCPU Q100UDEHCPU Basic model QCPU High performance model 3 QCPU Process CPU QO3UDCPU QO4UDHCPU QO6UDHCPU QIOUDHCPU 013UDHCPU Q20UDHCPU Q26UDHCPU QO3UDECPU QO4UDEHCPU QO6UDEHCPU QIOUDEHCPU 013UDEHCPU Q20UDEHCPU Q26UDEHCPU QSOUDEHCPU Q100UDEHCPU Universal model QCPU The combination is impossible An CAUTION 1 This produ
30. S 1 14 YADA MINAMI 5 CHOME HIGASHI KU NAGOYA JAPA When exported from Japan this manual does not require application to the Ministry of Economy Trade and Industry for service transaction permission Specifications subject to change without notice
31. S This will cause the BIOS to ignore the missing keyboard and continue the boot Memory address error at Indicates a memory address error at a specific location Press a key to REBOOT This will be displayed at the bottom of the screen when an error occurs that requires you to reboot Press F1 to disable NMI F2 to REBOOT BIOS detects a Non maskable Interrupt NMI condition during boot System halted CTRL ALT DEL to REBOOT Indicates the system should be rebooted Press and hold down the lt Ctrl gt lt Alt gt lt Del gt keys 95 8 Troubleshooting Hard disk s fail 80 HDD reset failed If you installed a CF card check if it is installed properly Hard disk s fail 40 HDD controller diagnostics failed Hard disk s fail 20 HDD initialization error If you installed a CF card check if it is installed properly Hard disk s fail 08 Sector Verify failed If you installed a CF card check if it is installed properly Keyboard error or no keyboard present Cannot initialize the keyboard Make sure the keyboard is attached correctly and no keys are being pressed during the boot BIOS ROM checksum error System halted The check sum of ROM address FOOOOH FFFFFH is wrong Memory test fail A BIOS error has occurred in an onboard memory test 96 8 Troubleshooting Necessary Information on your Inquiries If you would like to make an inquiry for us after judging the breakdown of this produ
32. Switch setting eo gt Detail setting AA ey Jime AY points A v 32points v 1 Intelli X Assigning the 1 0 address is not necessary as the CPU does it automatically Leaving this setting blank will not cause an error to occur A slot of an automatic layout Slot No Input module Additional module 32 32 32 o channels channels channels XO X40 X20 X40 Input and output mark E XOF X5F X3F X5F Input and output numbering It is divided by an auto Beginning XY is piled up and 16 points of not used is touched by default Take care enough not to cause the clash of the first XY of each slot If the clash happens intelligent function module assignment error error code 2107 SP UNIT LAY ERR follows 80 6 Combination with the MELSEC Q Series Access Forms This product Bus interface driver MELSECNET H module CC Link module Input module Output module Programmable controller CPU Intelligent function module gogog Power supply module CC Link Remote I O Remote Intelligent device device Power supply module Power supply module e B YO mues Y ae lool lopliae N Programma
33. anced Chipset Features Setup Table 4 6 Advance Chipset Feature select DRAM Timing Selectable Select DRAM Timing Selectable This item should be different values according to the parameter of the installed memory chip DRAM Do not change the value of factory settings unless you have installed new memory whose speed is different from the original DRAM ty Move ENTER Accept ESC Abort 38 4 BIOS Setup CAS Latency Time CAS Latency Time Select CAS Latency Time Select the number of clock in CAS waiting time When Synchronous DRAM is installed the number of clock in CAS waiting time is different according to DRAM timing Do not change the default value of factory settings 1 Move ENTER Accept ESC Abort DRAM RAS to CASA Delay DRAM RAS to CASE Delay Select DRAM RAS to CAS Delay Select the timing delay between CAS and RAS strobe signal E which are used when DRAM is read writed or updated When setting it to high speed the performance gets higher When setting it to low speed the performance gets more reliable It is applied only when synchronous DRAM is installed to the system 1 Move ENTER Accept ESC Abort DRAM RAS Precharge Do not change the default value of factory settings DRAM RAS Precharge Select DRAM RAS Precharge Select the number of clock needed to charge RAS till DRAM is refreshed If this value is not enough the update may become incomplete In this case DRAM can not
34. around Om An CAUTION When a commercial peripheral device such as a CF Card and USB device is installed satisfy the installation environment conditions specified for that device or those for the module whichever are harder 16 External Dimensions B B D D DH D oa D oa D op O CD O ID IDO oo ID OI oc CD O m rr E E E EE ee ee en EE ES EEE AAA es eee Y E EEE EEE 115 2 5 98 130 mm Fiture 2 1 External dimensions 2 System Reference 17 3 Hardware Setup 3 Hardware Setup Before Using the Product for the First Time Follow the next steps to set up this product This product works attached to the MELSEC Q series base unit MELSEC Q series power supply module is also necessary in addition to the base unit For their specifications and the methods of installation and wiring refer to manuals of each modules When using MELSEC products and MELSOFT products and you refer to their manuals and HELP replace the description PC CPU with the description MELSECWinCPU STEPI By referring to the information in this c
35. ble controller CPU Programmable controller CPU The Module can access various modules in the following forms 1 Access another programmable controller CPU in the local system 2 Access the I O module or intelligent function module in the local system 3 Access a programmable controller CPU via the MELSECNET H module 4 Access a remote I O remote device intelligent device or programmable controller CPU via the CC Link module 81 6 Combination with the MELSEC Q Series Multiple CPU Configuration Multiple CPU Configuration Including this product This product supports both of the single CPU configuration with the Module as only one CPU and the multiple CPU configuration with this product combined with other CPUs The maximum number of this product to be installed is only one Combination of CPUs Main base unit Q3 Module No 1 B Universal model QCPU QOOUCPU QO1UCPU QO2UCPU QOSUDCPU QO4UDHCPU QO6UDHCPU Q10UDHCPU 013UDHCPU Q20UDHCPU Q26UDHCPU QO3UDECPU QO4UDEHCPU QO6UDEHCPU Q10UDEHCPU Q13UDEHCPU Q20UDEHCPU Q26UDEHCPU QSOUDEHCPU Q100UDEHCPU Process CPU Number in which CPU module since Module No 2 can be installed Motion CPU 0172CPUN 0173CPUN Q172CPUN T Q173CPUN T 0172HCPU 0173HCPU Q172HCPU T Q173HCPU T 0172DCPU 0173DCPU Maximum number of installed Module No 1 is contained WinCPU module ___Basie modelQC
36. bort without executing the legitimate shutdown procedure Note that this may prevent the OS from running normally when restarted 3 Only when Windows Embedded Standard 2009 turning on SW 5 becomes effective 74 6 Combination with the MELSEC Q Series 6 Combination with the MELSEC Q Series Overview This product can communicate with the MELSEC Q Series programmable controller CPU module intelligent function module and I O module at high speed by connecting the buses using the MELSEC Q Series bus module Please refer to the manual of QCPU used for details regarding restrictions Note that the bus interface driver is used for communication with the various modules in the MELSEC Q Series including the programmable controller CPU For details on each MELSEC Q Series module and the bus interface driver refer to the relevant manuals System Configuration This product can be combined with MELSEC Q Series modules as shown below Main base unit Q33B Q35B Q38B Q312B Q38DB Q312DB QCO6B QC12BB QC30B QC50B QC100B E Q63B Q65B Q68B Q612B Q Series power supply QCPU 1 0 and intelligent function modules Add Q Series modules i i Q Series power supply I O i and intelligent function modules 75 6 Combination with the MELSEC Q Series Supported Modules
37. can not be used as a relay station of forwarding function between data links or rooting forwarding If you use forwarding function between data links or rooting forwarding select MELSECNET H module under the control of programmable controller CPU as a relay station c MELSECNET H special commands are not available d SEND RECV function is not available e Interrupt sequence program startup is not available f Network diagnosis test function is not available g Network easy doubling function is not available You can not set network classification to MNET H standby station h When it accesses other staions on doubling CPUs it can not specify the chain Only its own chain can be accessed where a station number is specified i Debug mode is not available 2 Note on using CC Link module CC Link module under the control of MELSECWinCPU module has following limitation a The parameter for CC link which is set on SWnD5C J61P n is later than 0 is not available In order to set the parameter use a CC Link utility provided by SWIPNC WCPU B b CC Link special commands are not available c Interrupt sequence program startup is not available d CC Link automatic startup is not available e It does not support remote I O network mode f It can not be set as a master station doubling function g Standby master function is not available 3 Note on using positioning module You cannot use the parameter
38. connector You can set it to COM1 4 or unused on BIOS setup refer to Chapter 4 BIOS Setup Table 5 6 SERIAL 1 I O address Interruption COM VO address Interrup tion IRQ 3 IRQ 4 IRQ 5 IRQ 7 IRQ 9 IRQ 10 IRQ 11 IRQ 15 The default setting of BIOS is as follows Serial port COM1 03F8H 03FFuH IRQ4 Table 5 7 Serial Connector Connector used 9 pin D SUB male connector 1 5 No 4 40UNC Inch screw 6 9 Pin No Signal name Meaning Direction 1 DCD Data carrier detect Input 2 RXD Receive data from equipment Input 3 TXD Transmit data to equipment Output 4 DTR Data terminal ready Output 5 GND Signal ground None 6 DSR Data set ready Input 7 RTS Request to send Output 8 CTS Clear to send Input 9 RI Ring indicator Input 70 CRT Interface A RGB It has a connector A RGB for CRT connection Table 5 8 RGB connector Connector used 15 pin HD SUB female connector 5 1 de Eee FN 15 11 Pin No Signal name Pin No Signal name 1 RED 9 N C 2 GREEN 10 GND 3 BLUE 11 N C 4 N C 12 DDC Data 5 GND 13 HSYNC 6 GND 14 VSYNC 7 GND 15 DDC CLK 8 GND None 5 Each Component Function In order to know which LCD can connect to it refer to Chapter 9 List of Options and Recommended Parts Display driver Installed A CAUTION Connected displays should be comp
39. ct cannot be Module No 1 in the multiple CPU configuration The multiple CPU configuration requires a programmable controller CPU 2 For the multiple CPU configuration place this product at the right end of a series of CPUs 3 Although a total ofup to three programmable controller CPUs and motion CPUs can be installed the number of modules installable is restricted by the power capacity of the power supply module Q61P See Restriction by Power Capacity in Notes for details 83 6 Combination with the MELSEC Q Series CPU Configuration Diagrams Single CPU configuration with this product as only one CPU Module No 1 This product looligllodligg Es 4 Lie This product Multiple CPU configuration with this product in combination with programmable controller CPUs Maximum configuration with this product and three programmable controller CPUs Modules No 1 3 Programmable controller CPU Module No 4 This product oo000 Oooog DODDO eels loollalllo oler dele o This product Programmable controller CPU Up to 3 modules Install as the right most CPU Multiple CPU configuration with this module in c
40. ct or from other reasons you have to tell us following status and situation Information of a problem Q1 Information of the product Product name Seial No Q2 What happens as the problelm No screen appears even if turning power ON LED does not light Peripheral devices cannot be recognized VO function cannot work Communication cannot work Ohters Q3 Situations before the problem happended Installed software Added peripheral devices External factors thunder water or oil hazard etc None Q4 Solutions after the problem happended Changed it to a compatible product and got normal operation Checked it under isolated construnction and judged that it would have problem Others Q5 Confirmation results by diagnosis program sample program etc Result Q6 Usage status Purchase date approximate Month Year Purchase number Pcs Q7 The date when the problem happened and repeatability The date when the problem happened Day Month Year a Frequency L Always Quite frequently ___ times ___ hours LJSometimes ___ times ___ hours The condition to happen If there exist any special conditions to cause the problem Q8 Usage environment and operating time Inside the control panel in a factory or similar conditions Outdoors 8 hours day wor
41. d the self test will not be simplified Quick Power On Self Test Select Disabled Enabled of Quick Power On SelfTest Disabled Selecting Enabled makes POST the self test when Enabled turning power on simpler Therefore the wake up time becomes shorter But we recommend selecting Disabled Because POST will not be processed for all the system if not If some troubles happen on POST specify them in order to avoid the loss of data while working t4 Move ENTER Accept ESC Abort 33 4 BIOS Setup USB Device Wait USB Device Wait Dis abled 5 Sec Select USB Device Wait 10 See This menu sets the BIOS waiting time till the access for 20 Sec USB devices starts 30 Sec If you can not boot the system in order because of the USB 60 Sec devices which need the long time to start use this function The boot time of system will be as long as the time you set t4 Move ENTER Accept ESC Abort First Boot Device Removable u E First Boot Device Hard Disk sss CDROM Select First Boot Device Disabled BIOS try to load operating system from devices according to the order specified by this item 1 Move ENTER Accept ESC Abort Second Boot Device Removable Second Boot Device Hard Disk CDROM Select Second Boot Device Disabled BIOS tries to load operating system from devices according to the order specified by this item 1 Move ENTER Accept ESC Abort Third Boot Device Removable u Th
42. dBIOS CMOS Setup Utility USB Device Setting USB 1 0 Controller Enabled USB 2 0 Controller Enabled USB Operation Mode High Speed USB Keyboard Function Disabled USB Storage Function Enabled USB Mass Strage Device Boot Setting t lt Move Enter Select PU PD Value F10 Save ESC Exit Fi General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 4 11 USB Device Setting Table 4 11 USB Device Setting select Description Disabled USB 1 0 Controller Enabled Select Disabled Enabled of USB 1 0 Controller Normally select Enable Disabled USB 2 0 Controller Enabled Select Disabled Enabled of USB 2 0 Controller Normally select Enable 1 Move ENTER Accept ESC Abort 47 4 BIOS Setup USB Operation Mode Full Low Speed High Speed USB Operation Mode Select USB Operation Mode USB Keyboard Function Disabled Enabled Select Disabled Enabled of USB Keyboard Function If you use a USB keyboard on the OS which does not support USB select Enabled For the OS which supports USB select Disabled Disabled nabled USB Storage Function E Select Disabled Enabled of USB Storage Function When using USB storages select Enabled 1 Move ENTER Accept ESC Abort 48 4 BIOS Setup Power Management Setup The Power Management Setup allows you to configure you system to most effectively save energy while
43. difying the product To clean this product gently wipe it with a soft cloth soaked with water or a neutral detergent Do not use benzene paint thinner or other volatile solvents as they can cause the coating to discolor or peel off The specifications of this product are subject to change without notice because of function addition and quality improvement Even when using the product continuously read the user s manual and check the contents If you move or transfer the product make sure to provide this manual with the product Regardless of the foregoing statements Mitsubishi is not liable for any damages whatsoever including damages for loss of business profits arising out of the use or inability to use this Mitsubishi product or the information contained herein When disposing of a used battery follow the disposal procedures stipulated under the relevant laws and municipal ordinances Design Precautions A WARNING A CAUTION Provide this product with external safety circuits so that the entire system is protected even if the external power supply malfunctions or this product breaks down If not incorrect output or incorrect operations may lead to accidents 1 Configure those circuits outside this product that include an emergency stop circuit a protection circuit an interlock circuit with contrary operations such as normal reverse rotations and an interlock circuit for preventing a machine from breaking beyond the up
44. ding to exportation regulations But if you export it after re packaging or unpacking you should export it according to IATA Dangerous Goods Regulations IMDG Code and other exportation regulations of each contries For details consult your transporter We charge for battery exchange Consult a nearby branch or an agency Appendix 3 Disposal of Battery Remove of battery Remove the battery as folows 1 Remove screws and take the case off 102 10 Appendix Disposal of battery When dumping the product treat it as an industrial waste When disposing of a battery separate it according to regional laws of your area An CAUTION EU has a separate collection system for used batteries Dispose it correctly at a collection recycle center in your area Mitsubishi programmable controller CPU shows a following symbol mark on the battery or the package of the product including a battery Note This symbol mark is valid in EU only This symbol mark is listed on the 20th clause Information for an end user of directive 2006 66 EC of the European parliament and of the council and on the attached document II The symbol mark above indicates that the battery should be dumped separately from normal wastes Exportation of Battery According to directive 2006 66 EC of the European parliament and of the council you should keep the following procedures when selling or exporting a battery or the product with a battery T
45. duct Do not use or store the product in a hot or cold place or in a place that is subject to severe temperature changes Doing so may cause malfunction heat generation fault or damage Do not use or store the product in a place subject to direct sunlight or near a heating device such as a stove And do not use or store the product near equipment generating a strong magnetic field or radio waves Doing so may cause malfunction heat generation fault or damage Some products have to be set up before they can be used normally Be sure to check whether the product is such before use Set the switches and jumpers only as specified or the product may develop trouble When the power is ON don t change any DIP switches except for SW 2 of DIP switch 1 If not the product may develop abnormal conditions such as the hangup of OS system crash and irregular operation You can set SW 1 of DIP switch 1 to ON only when power is OFF If SW 1 is ON when power is ON it does not work in order You should check that SW 1 is OFF before turning power ON You should wait for 5 minutes after power OFF till the next power ON operation The monitor connected to this product may not be able to show screen in order if power of the monitor was turned ON at an incorrect time Turn ON power of a monitor before turning ON power of this product When using some USB devices the current may flow to this product reversely via a conneted cable wh
46. e attempting to use this product in a place subject to considerable vibration or shock use the module fixing screw to fasten this product securely to the base unit Module fixing screw must be tightened within the specified tightening torque range Tightening the screw loosely can allow this product to fall cause a short circuit or malfunction Tightening the screw excessively can break the screw or module allow this product to fall a short circuit or malfunction When connecting an extension cable plug it securely into the relevant connector on the base unit or the Module Check the connection after plugging it in to prevent an imperfect contact which can cause input and output errors Before attaching or detaching this product be sure to turn the external power supply off for all phases or this product may be damaged Never directly touch any conductive part or electronic component of this product Doing so may cause the Module to malfunction or fail A CAUTION Before mounting or unmounting this product or any other product be sure to turn the external power supply off for all phases Failure to turn it off for all phases may cause product damage The exchange of modules under online power on conditions is possible only when the system is built with the programmable controller CPU modules supporting the online module exchange or the target module is MELSECNET H remote I O station But the modules supporting the exchange under
47. e binding tie The binding tie can be installed as follows in order to keep USB cables from falling out A recommended binding tie RSG 100 VO Kitagawa Industries AUN WWMM Figure 3 5 The hole to attach the binding tie 21 4 BIOS Setup 4 BIOS Setup BIOS Setup BIOS Setup allows you to make various settings upon startup When you use the Module for the first time be sure to execute this program Once you have executed the program the settings you made are backed up to be retained Introduction This chapter discusses Award s Setup program built into the FLASH ROM BIOS The Setup program allows users to modify the basic system configuration This special information is then stored in battery backed RAM so that it retains the Setup information when the power is turned off The rest of this chapter is intended to guide you through the process of configuring your system using Setup Starting Setup The Award BIOS is immediately activated when you first power on the computer The BIOS reads the system information contained in the CMOS and begins the process of checking out the system and configuring it When it finishes the BIOS will seek an operating system on one of the disks and then launch and turn control over to the operating system While the BIOS is in control the Setup program can be activated in one of two ways By pressing lt Del gt immediately after switching the system o
48. e connectors for external connection must be crimped welded with pressure or soldered correctly with the relevant tool For the crimping and pressure welding tools refer to the input output module user s manual An imperfect connection can cause a short circuit fire or malfunction For the cables connected to this product wire them so that they do not interfere with the switches and the LEDs of the product Power Supply and Maintenance Precautions A WARNING Never touch any terminal with the Module powered or it may malfunction Before cleaning this product or tightening up terminal screws be sure to turn the external power supply off for all phases Failure to turn it off for all phases may either result in an electric shock or cause this product to fail or malfunction Tightening the screw loosely canallow this productto fall cause a short circuit or malfunction Tightening the screw excessively can break the screw or this product allowing this product to fall cause a short circuit or malfunction Do not touch any terminal with this product powered on or it may malfunction An CAUTION Read the manual thoroughly and check the entire system sufficiently for safety before performing online operations during a machine run in particular for a program change forced output and operation status change An operation error can break the machine or cause an accident Donot disassemble or modify any module Doing so
49. eane User Define You can set values for each mode individually The Min Saving selectable range is between 1 minute and 1 hour when it is Max Saving enabled Min Saving Minimum power management is processed Suspend mode 1 hour Maximum power management is processed Suspend mode 1 minute 50 4 BIOS Setup Video Off Method Video Off Method Select the power management method of video in the Video Off Method standby mode Blank Screen V H SYNC Bl ank Blank Screen DPMS Turns the screen off V H SYNC Blank Turns V H SYNC and display signals off DPMS Controls it accorging to DPMS The connected display should support DPMS Video Off In Suspend Selecting Yes a video becomes off in the standby mode Stop Grant PwrOn Suspend Suspend Type Select Suspend type The option is Stop Grant and PwrOn Suspend Disabled Suspend Mode 1 Min 2 Min If no power management event happen between the 4 Min Mad Reel Mac Reed Mia feel Maca hu Mal ku specified period CPU clock stops and a video signal 8 Min 12 Min 20 Min When any power management events are detected the 30 Min becomes the suspended condition system wakes up from the suspended condition 40 Min 1 Hour 1 Move ENTER Accept ESC Abort nn nn na na rn FN E Reload Global Timer Events Selecting Enabled the global timer of the standby mode restarts following the respective event carried ou
50. ed at no cost via the sales representative or Mitsubishi Service Company However if repairs are required onsite at domestic or overseas location expenses to send an engineer will be solely at the customer s discretion Mitsubishi shall not be held responsible for any re commissioning maintenance or testing on site that involves replacement of the failed module Gratis Warranty Term The gratis warranty term of the product shall be for one year after the date of purchase or delivery to a designated place Note that after manufacture and shipment from Mitsubishi the maximum distribution period shall be six 6 months and the longest gratis warranty term after manufacturing shall be eighteen 18 months The gratis warranty term of repair parts shall not exceed the gratis warranty term before repairs Gratis Warranty Range 1 The range shall be limited to normal use within the usage state usage methods and usage environment etc which follow the conditions and precautions etc given in the instruction manual user s manual and caution labels on the product 2 Even within the gratis warranty term repairs shall be charged for in the following cases 1 Failure occurring from inappropriate storage or handling carelessness or negligence by the user Failure caused by the user s hardware or software design 2 Failure caused by unapproved modifications etc to the product by the user 3 When the Mitsubishi product is asse
51. em Specifications Surrounding air temperature 0 to 55 C Surrounding storage temperature 25 to 75 C Surrounding operating humidity 5 to 95 RH No condensation Surrounding storage humidity 5 to 95 RH No condensation With intermittent vibration Tested 10 Amplitude times in each of the 8 4 lt f lt 150Hz 9 8m s none X Y and Z directions With continuous vibration Vibration resistance Shock resistance Conforming to JIS B 3502 IEC61131 2 147m 82 3 times in each of 3 direction Operating ambiance No corrosive gas Operating altitude 0 to 2000m 3 Installation location Inside the control panel Overvoltage category II or less Pollution degree 2 2 or less Equipment category Class I 1 The overvoltage category of a device indicates which distributor in the range from public distribution network to Machinery the device is assumed to be connected to Category II applies to devices to which power is supplied from fixed facilities The surge voltage of those devices is 2500V whose rated voltage is 300V 2 The index indicating the degree to which conductive substances are generated in the operating environment Pollution level 2 indicates the environment that generates only nonconductive pollutants while allowing accidental condensation to cause temporary conduction 3 The module may fail and cannot be used in an environment in which the air is compressed to over the atmospheric pressure generated at an altitude of
52. en power of this product is OFF In this case you may not be able to boot up this product because 5V power is kept to ON When this problem happens remove the USB device turn ON power of this product and then connect the USB device again If you want to use the USB device as a boot device connect it by the time that device detenction starts Keep the inside of a module away from foreign objects such as chips or wire scraps It may lead to fire breakdown and irregular operations Do not use or store this product where any chemical atmosphere and objects can touch the product Do not use or store this product where excessive moisture or a lot of dust exists It is very dangerous if you use the product where there is high humidity liquid objects or conductive dust When you have to use the product under such conditions set the product in the protected structure against dust such as the control panel with dust protection Ifyou notice abnormal odor or overheating please disconnect the power cable immediately After you become aware of breakdown or abnormal conditions such as an abnormal smell or excessive heading first turn the power OFF Then make contact with the store which provided the product Do not open the product casing Mitsubishi will disclaim any responsibility for products whose casing has been opened Do not modify the product Mitsubishi will bear no responsibility for any problems etc resulting from mo
53. er caught in this product may cause a fire fault or malfunction Wire each product to the module correctly after checking the rated voltage and pin assignments of the product Connecting a power supply not matching the rating or miswiring may cause a fire or fault Tighten each terminal screw within the specified tightening torque range Tightening the terminal screw loosely may result in a short circuit or malfunction Tightening the terminal screw excessively can break the screw or the Module also resulting in a short circuit or malfunction When you connect external components to this product connect them after the installation The cables connected to this product must be either enclosed in ducts or fixed with clamps Doing neither allows the cables to hang loose move or be pulled inadvertently resulting in this product and or cables becoming damaged or this product malfunctioning due to an imperfect contact in the cable connection When disconnecting each cable from this product do not hold the line to pull Unplug the cable after loosening the screws fastening the cable end to the connector in this product Pulling the cable connected to this product may break this product and or cable or cause this product to malfunction due to an imperfect contact in the cable connection Do not connect the outputs of two or more power modules in parallel Doing so heats up the power modules possibly causing a fire or fault Th
54. erface driver allows this product to access various MELSEC Q Series modules such as the programmable toggle switch controller CPU I O and intelligent function modules 2 The MELSEC Q Series sequence program places Y at the beginning of the output number of each output module The Y output signifies the output to an output module Examples of using the toggle switch for the single CPU configuration with this product alone Operation expected Action to take modules on the bus modules on the bus esets the modules on the bus and 1 Set the toggle switch to B RUN recover from the reset 2 Hold the toggle switch at the B RST position for two seconds then release the switch 3 Set the toggle switch to B RUN 4 Execute the user application 73 5 Each Component Function DIP switch 1 omen 1234 ON Figure 5 6 Factory Default of DIP switch 1 CMOS clear switch factory setting OFF Refer to Chapter 4 Position and Setting of CMOS ROM clear switch ROM clear switch factory setting OFF Refer to Chapter 4 Position and Setting of CMOS ROM clear switch SSD Enable switch factory setting OFF ON It sets built in SSD to Disabled 4 poles sliding OFF It sets built in SSD to Enabled Refer to Chapter 5 Built in SSD SSD write protect switch factory setting OFF This switch controls the write protect function of built in SSD ON It forbids built in SSD to be writed in OFF It permi
55. finished Press alphabet key A Z and reboot the system BACKUP finish Press any key reboot 10 When the screen of BIOS appears in rebooting turn the power off That finishes the backup procedure You cannot boot the OS using the CF card for backup Rewrite procedure from the CF card for backup to built in SSD for OS For previous procedure rewrite procedure will be done by selecting the CF card for backup as Source Disk and built in SSD for OS as Destination Disk Other procedures are the same as the backup 106 10 Appendix REVISIONS The manual number is given on the bottom left of the back cover Manual number Revision December 2011 SH NA 081055ENG A First edition Japanese manual version SH 081044 B This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual 2011 MITSUBISHI ELECTRIC CORPORATION 107 WARRANTY Please confirm the following product warranty details before using this product 1 Gratis Warranty Term and Gratis Warranty Range If any faults or defects hereinafter Failure found to be the responsibility of Mitsubishi occurs during use of the product within the gratis warranty term the product shall be repair
56. hapter install connect and set this product STEP2 Connect cables Connect the cables of necessary external devices such as a keyboard and a display to this product using appropriate cables STEP3 Turn on the power After verifying that you have correctly followed steps 1 and 2 turn on the power If you find any abnormality after turning on the power turn it off and check to see ifthe setup has been performed properly STEP4 Set up BIOS By referring to Chapter 4 set up BIOS This setup requires a keyboard and a display Before using this product be sure to execute LOAD SETUP DEFAULTS to initialize the BIOS settings to their default values See Chapter 4 Main Menu Note that this product occupies two slots in the base unit An CAUTION Before installing or uninstalling this product be sure to turn the power off Installing or uninstalling this product while the power is on can cause a fault or malfunction Be sure to connect a keyboard and a mouse to it before turning the power on for the first time 18 3 Hardware Setup Installing the Module For the environment and the position to install this product refer to QCPU User s Manual Hardware Design Maintenance and Inspection Before installing this product remove the transparent protective sheet from the rear panel which comes into contact with the base unit Fit the module fixing hook in the module fixing slot in the base unit then push
57. he indication of the symbol mark on a battery a product or a package Description about the symbol mark in the product guide 1 The indication of the symbol mark If you sell or export the battery or the product with the battery which does not display the symbol mark to EU after 2008 09 26 indicate the symbol mark of Appendix 3 Disposal of Battery on the main body of a product or on its package 2 Addition of the explanation to a product guide When you export the product with our sequencer to EU after 2008 09 26 and you attach the product guide of our programmable controller CPU to it attach the latest product guide which has the explanation of the symbol mark of a battery When you don t attach the product guide of our programmable controller CPU or an attached product guide is an older one which doesn t have the explanation of the symbol mark newly describe the explanation of the symbol mark on the product guide of each product A CAUTION The battery and the product with a battery produced before the enforcement of directive 2006 66 EC are also come under the directive 103 10 Appendix Appendix 4 EMC directive If you want to apply EMC directive and low voltage derective to MELSECWinCPU system refer to QCPU User s Manual Hardware Design Maintenance and Inspection Appendix 5 Backup of built in SSD This section shows how to use the backup function of the BIOS of MELSECWinCPU This function sup
58. hooting This product Won t Start Normally SW 1 of DIP switch 1 is OFF Set SW 1 of DIP switch YES 1 to OFF NO Started normally Remove each unit and check whether the system is started normally YES the power supply base unit and End in the basic configuration made up of MELSECWinCPU module Started normally Did you send 3 or more secs of shutdown inputs via an I O terminal NO Replace the YES MELSECWinCPU module Via an I O terminal OFF gt 0N 20msec 3sec gt 0FF is performed for a shutdown input in the state of power supply ON NO Started normally Replace the power and End Started normally gt NO YES Consult your local Started normally system service End desk or agency of Mitsubishi Electric Power capacity OK NO Corporation Consult your local system service desk or agency of YES Mitsubishi Electric Corporation Install the removed Review the system modules one by one configuration to check Any module out of order NO Consult your local system service desk or agency of Mitsubishi Electric Corporation 91 8 Troubleshooting This product Starts with a BIOS Error displayed NO Set SW 1 of DIP switch 1 to OFF Started normally SW 1 of DIP switch 1 is OFF Check the error with the BIOS error list and take appropriate action Error removed Consult your loca
59. inCPU setting utility you can read the default setting of the parameters of an intelligent function module from the project file of GX Developer If using GX Works2 first save the project as GX Developer format and read it For the note on available project files of GX Developer refer to followings MELSECWinCPU Module Q Bus Interface Driver User s Manual Utility Operation Programming 78 6 Combination with the MELSEC Q Series Notes on I O No assignment MELSECWinCPU module occupies 2 slots Therefore the right 1 slot of occupied 2 slots would be treated as a blank slot Don t set I O assignment to the right 1 slot Default settings occupy Blank 16 points and I O No of the right slot neighboring a MELSECWinCPU module becomes 0010H You can use I O No from 0000p for the right slot neighboring a MELSECWinCPU module by setting 0 points to the right 1 slot of 2 slots occupied by MELSECWinCPU module 1 Slot conditions after I O assignment Slots after I O assignment settings would work according to the specification of the mounted module a If you set less points than ones of mounted I O module The actual available points of mounted I O module would get less For example if you set 16 points for the input module with 32 points you can not use descending 16 points b If you set less points than ones of mounted intelligent function module Intelligent function module assignment erro
60. ird Boot Device Hard Disk mm CDROM osas Select Third Boot Device Disabled mom BIOS tries to load operating system from devices according to the order specified by this item 1 Move ENTER Accept ESC Abort 34 4 BIOS Setup Boot Other Device Dis abled Boot Other Device Select Disabled Enabled of Boot Other Device If selecting Enabled BIOS try to load operating system from other devices ti Move ENTER Accept ESC Abort Boot Up NumLock Status Select Boot Up NumLock Status It controls the condition of lt NumLock gt key on the start of the system Gate A20 Option Select Gate A20 Option It selects how to specify address for the memory which is larger then 1MB extended memory Sellecting Normal the gate A20 is controlled by the pin of keyboard controller Sellecting Fast the gate A20 is controlled by the system chipset For OS 2 and Windows selecting Fast can make the speed of the system higher 1tJ Move ENTER Accept ESC Abort Typematic Rate Setting Select Typematic Rate Setting Selecting Disabled the speed of typing is decided by the keyboard controller of the system Selecting Enabled you become able to select following 2 items Typematic Rate and Typematic Delay Typematic Rate Chars Sec Select Typematic Rate You can select the input speed of characters when you keep one key pushed If the item Typematic Rate Se
61. isproduct Won t Start No A seines 91 This product Starts with a BIOS Error displayed ccccccccccsscccesseceeseeeceseeeeeeeeesesesseseeesseeees 92 The OS Wont Start Normally esi un ae aaa 93 It hangs up at the time after OS starting of operation oooconoocccocononncnonoconanonnconncnonaconononanacnnannns 94 BIOS E is erahnen ep ren EIERN ei 95 Necessary Information on your Ing inies en nen e en bie 97 9 List of Options and Recommended Parts 98 16312126118 0 615 0 1 7 gt PAWSRSE ES ie ES 98 List of Recommended Parts ARES 98 10 Appendix 99 Appendix 1 Resources Hr aides apie ee Oe a 99 Memory Map did iii 99 TO portada o e e ad a o lo 100 Interrupt Level Li DER 101 Appendix 2 Baltev as ERC PE ORS a Ole ee 102 Appendix 3 Disposal of Battery are ee 102 Appendix 4 EMC directive een ee Seesen 104 Appendix 5 Backup of built in SSD ana direc 104 Backup PEO CCU E E ee 104 Rewrite procedure from the CF card for backup to built in SSD for OS oooooconnoccccnoncccoooncnoncncnnononononos 106 TEE WES GOINGS hg wh esa Re ee Biere N 107 WARRANTY Nase RR E 108 1 Introduction 1 Introduction About the Product This product is the controller which can be installed with Mitsubishi General programmable controller CPU MELSEC Q Series and supports Windows OS This product can work as the multiple CPU configuration with programmable controller CPU and it realizes the seam less processing of both controlling and comp
62. it near any main circuit high voltage large current line 4 Set the expansion stage numbers in ascending order without number duplication 5 Connect each extension cable from the extension cable connector OUT on one base unit to the extension cable connector IN on the expansion base unit at the next 6 Installing 65 modules or more results in an error stage 85 6 Combination with the MELSEC Q Series When installing Multiple CPU configuration Refer to QCPU User s Manual Multiple CPU System Restriction by Power Capacity The current consumption of this product is the total value of one of the main body and ones of peripheral devices Take care that the summation of the current consumption of this product and ones of other modules should not exceed the power capacity of your Q series power module For the actual current consumption values of modules refer to their manuals Multiple CPU configuration with a CF card As the Q61P cannot be used if the total current consumption of the modules exceeds 6A consider using the Q64PN power capacity 5VDC 8 5A instead Number of CPU modules Remaining current Main base Programmable Motion CPU Thi act N TEEN capac ty urren controller CPU ke Pen A consumption Q25HCPU Q173CPUN BIN m Q312B ay Q61P 0 64A 1 25A eee OORA ga udgement o_o d al o ef o a ao al sed om o Y ER RR oo 3 1 1 1 1 A 5 717 0 283 1 1
63. ks 24 hours day works Others 97 9 List of Options and Recommended Parts 9 List of Options and Recommended Parts List of Options CF card EL 15 inch 1024 x 768 dots FPD H21XT AC CONTEC CO LTD Panel mounted type TFT color liquid crystal i 12 1 inch 800 x 600 dots display FPD L21ST AC CONTEC CO LTD Panel mounted type Analog RGB types 10 4 inch 640 x 480 dots FPD M21VT AC CONTEC CO LTD Panel mounted type RS 232C cable 2m IPC CBL3 2 CONTEC CO LTD Touchpanel cable RS 232C cable 5m IPC CBL3 5 CONTEC CO LTD List of Recommended Parts Name Model Name USB keyboard D1T 00007 Microsoft USB HUB MOXA 98 10 Appendix Appendix 1 Resources Memory Map FFFEFF Extended memory D0000000n FFFFFFFFH is reserved by the system 100000 EFEFEF Extended system BIOS 28000 96KB E7FFF System BIOS E0000 82KB E0000 Expansion area 64KB D0000 CFFFF Video memory and VBIOS 192KB A0000 9FFFF Conventional memory 640KB 00000 Figure 10 1 Memory map 10 Appendix 99 10 Appendix VO port address Table 10 1 I O port address Address 0000n 000FH Size 16 bytes DMA controller 16 bytes Reserved 2 bytes PIC interrupt controller 30 bytes Reserved 4 bytes System timer 1 N 24 bytes 1 byte Keyboard controller 2 bytes 1 byte 4 bytes 12 bytes 17 bytes 2 bytes 2 bytes
64. l system service desk or agency of Mitsubishi Electric Corporation 92 8 Troubleshooting The OS Won t Start Normally SW 1 of DIP switch lis OFF Set SW 1 of DIP switch 1 to OFF Started normally The OS displayed a system error on the Blue Screen upon startup YES Reinstall Windows The OS displayed a system error on the Blue Screen upon startup YES YES Consult your local system service desk or agency of Mitsubishi Electric Corporation Any driver message in the management tool Event Viewer Check settings according to the details about the error Any error inform ation displayed about MELSECWinCPU module unit settings YES Consult your local system service desk or agency of Mitsubishi Electric Corporation Check settings according to the details about the error 93 8 Troubleshooting It hangs up at the time after OS starting of operation NO SW 1 of DIP switch 1 is OFF Set SW 1 of DIP switch 1 to OFF Started normally YES NO YES The OS displayed a system error on the Blue Screen upon startup YES Reinstall Windows NO It re starts The OS displayed a system error on the Blue Screen upon startup YES OS does not carry out normal starting It hangs up at the time at the time of OS starting of operation YES
65. le DIP switch 6 pole 3 position toggle switch Supported OS Windows Embedded Standard 2009 1 When power is on you can not push in pull out a CF card Memory card is supported but other purposes are not supported 2 Access LED shows the access of both a CF card and built in SSD 3 Built in SSD is used as OS space SSD has rewritable life 1 million times For details refer to Built in SSD of Chapter 5 Each Component Function 4 Current capacity shows the maximum value the connector supports But the actual value is limited because the total current cannot exceed the capacity of the power supply module Therefore the actual available value may be less than 0 5A 5 General I O is not evaluated by UL 6 When you want to use it in noisy environments we recommend you to use the following noise filter Noise filter for general I O NAC 06 472 Mfd By COSEL 15 2 System Reference Table 2 1 Functional Specification 2 2 Specifications Physical dimensions mm 55 2 W x 115 0 D x 98 0 H Excluding protrusions DC5V internal current consumption 3 0A Max This does not include the current consumption by any peripheral devices such as the CF Card and USB device Acceptable momentary power failure time Depending on the power supply module Q10WCPU W1 E 440g Weight Q10WCPU W1 CFE 450g Including CF card Fittings and screws to fix a CF card Table 2 2 Installation Environment Conditions It
66. liant with the VESA standard The display may show nothing according to the type of connected monitor after the install of VGA driver In the case press lt Ctrl gt lt Alt gt and lt F1 gt keys at the same time When the analog display is used Windows MS DOS may not be properly be displayed in full screen mode This is because the frequency and resolution of Windows and MS DOS full screen display are the same due to the screen settings while the display parameters are different For display as only one parameter can be stored for one frequency or resolution only either of Windows or MS DOS screen can be displayed properly In this case change the resolution or display frequency of Windows so that it is not the same as for the MS DOS display 71 5 Each Component Function USB Port It has Sch of USB 2 0 interface USB Figure 5 9 USB connector Pin No Signal name 1 Vee 5V 2 DATA 3 DATA 4 GND Maximum power supply The power capacity which each channel of USB connectors can supply is as follows But the actual power capacity to supply is limited by the requirement that the current comsumption of the total system can not exceed the capacity of the power supply module Therefore actual available capacity cannot necessarily be equal to the maximum power capacity to supply The maximum power capacity to supply 5V 0 5A Max channel An CAUTION When selecting USB devices
67. lt or failure occurring in the PRODUCT if any shall not lead to any major or serious accident and 11 where the backup and fail safe function are systematically or automatically provided outside of the PRODUCT for the case of any problem fault or failure occurring in the PRODUCT The PRODUCT has been designed and manufactured for the purpose of being used in general industries Mitsubishi shall habe no responsibility or liability including but not limited to any and all responsibility or liability based on contract warranty tort product liability for any injury or death to persons or loss or damage to property caused by the product that are operated or used in application not intended or excluded by instructions precautions or warning contained in Mitsubishi s user instruction and or safety manuars technical bulletins and guidelines for the product Prohibited Application Prohibited Applications include but not limited to the use of the PRODUCT in Nuclear Power Plants and any other power plants operated by Power companies and or any other cases in which the public could be affected if any problem or fault occurs in the PRODUCT Railway companies or Public service purposes and or any other cases in which establishment of a special quality assurance system is required by the Purchaser or End User Aircraft or Aerospace Medical applications Train equipment transport equipment such as Elevator and Escalator Incine
68. mable controller CPU systems refer to the manual of the corresponding CPU module This Safety Precausions classify the level of precautions into A Warning and N Caution N W Warning indicates that dangerous situations will lead to death or arming serious injury if the right procedures are not followed Caution indicates that dangerous situations will lead to light injury or Caution the loss of property if the right procedures are not followed The items mentioned in N Caution also can cause serious accidents according to the situation O A oF BE The mentioned items are all important You must follow them Keep this manual carefully at hand in order to read at any time and have it available for the end user Handling precautions A WARNING Never use this product in locations where there is flammable gas and corrosive gas It may lead to explosion fire electric shock and breakdown The operating product may reach a high temperature Never touch its surface It may lead to burns Never touch this product with wet hands It may lead to electric shock A CAUTION As this product contains precision electronic components do not use or store it in a place subject to shock or vibration Doing so may cause malfunction heat generation fault or damage Donot modify the product Mitsubishi will bear no responsibility for any problems etc resulting from modifying the pro
69. mbled into a user s device failure that could have been avoided if functions or structures judged as necessary in the legal safety measures the user s device is subject to or as necessary by industry standards had been provided 4 Failure that could have been avoided if consumable parts battery backlight fuse etc designated in the instruction manual had been correctly serviced or replaced 5 Failure caused by external irresistible forces such as fires or abnormal voltages and failure caused by force majeure such as earthquakes lightning wind and water damage 6 Failure caused by reasons unpredictable by scientific technology standards at time of shipment from Mitsubishi 7 Any other failure found not to be the responsibility of Mitsubishi or that admitted not to be so by the user 108 2 Onerous repair term after discontinuation of production 1 Mitsubishi shall accept onerous product repairs for six 6 years after production of the product is discontinued Discontinuation of production shall be notified with Mitsubishi Technical Bulletins etc 2 Product supply including repair parts is not available after production is discontinued 3 Overseas service Overseas repairs shall be accepted by Mitsubishi s local overseas FA Center Note that the repair conditions at each FA Center may differ 4 Exclusion of loss in opportunity and secondary loss from warranty liability Regardless of the gratis warranty term
70. n or By pressing the lt Del gt key when the following message appears briefly at the bottom of the screen during the POST Power On Self Test Press DEL to enter SETUP If the message disappears before you respond and you still wish to enter Setup restart the system to try again by turning it OFF then ON or pressing the RESET button on the system case You may also restart by simultaneously pressing lt Ctrl gt lt Alt gt lt Del gt keys If you do not press the keys at the correct time and the system does not boot an error message will be displayed and you will again be asked to Press F1 to continue DEL to enter SETUP 22 4 BIOS Setup Using Setup In general you use the arrow keys to highlight items press lt Enter gt to select use the PageUp and PageDown keys to change entries press lt F1 gt for help and press lt Esc gt to quit The following table provides more detail about how to navigate in the Setup program using the keyboard Table 4 1 Using Setup Key Up Arrow Down Arrow Left Arrow Right Arrow PgUp key PeDn key key Main Menu Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu Exit current page and return to Main Menu Getting Help Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item To exit the Help Window press lt Esc gt or the F1 key again In Case
71. n SSD a CF card 1 When the B RUN LED is blinking do not reset again the bus interface driver by setting the toggle switch to B RST or resetting module No 1 in the multiple CPU configuration 2 When the shutdown of OS is completed nothing is displayed on a CRT screen but it becomes a black screen 67 5 Each Component Function Terminal block I O Connect it using the terminal block connector packed with this product Table 5 5 Terminal Block Shutdown input Refer to figure 5 2 An CAUTION Shutdown input output is supported by Windows Embedded Standard 2009 only If ON period of shutdown input is longer than 5 seconds the forced shutdown will run It is not a normal shutdown After this procedure OS may not boot up in order In general do not use the forced shutdown When you want to shutdown the OS Windows Embedded Standard 2009 using the shutdown input the ON period should be within the range 0 7sec 3sec If you want to reboot the module after the normal shutdown or the forced shutdown the condition that the shutdown complete output of this module is ON and EXIT LED of MELSECWinCPU module lights you should turn power off gt on or send a signal to the shutdown input ON period 0 7sec 3sec again If the reset button of a MELSECWinCPU module is pushed you can not reboot the module If the shutdown input is ON a MELSECWinCPU module can not start up When y
72. nnel 0 1 None select the number of cylinders heads etc Selecting Auto Manual lets you set the re maining fields on this Master Slave Manual screen Note PRECOMP 65535 means NONE Access Mode Choose the access mode for this hard disk Disk drive capacity Approximated Note that this size A Automatically shows the 3 Capacity is usually slightly greater than the size of a formatted capaticy of HDD i y i 2 disk given by a disk checking program The following options are selectable only if the IDE Channel 0 2 Master Slave item is set to Manual and Acces Mode item is set to CHS Min 0 Cylinder u Set the number of eylinders for this hard disk Max 65535 Min 0 i Head Set the number of heads for this hard disk Max 255 Min 0 Warning Precomp k Max 65535 Setting a value of 65535 means no hard disk Min 0 Landing Zone ed pee Max 65535 Min 0 Sector re Number of sectors per track Max 255 28 4 BIOS Setup Advanced BIOS Features Setup This section allows you to configure your system for basic operation You have the opportunity to select the system s default speed boot up sequence keyboard operation shadowing and security Phoenix AwardBIOS CMOS Setup Utility Advanced BIOS Features gt CPU Feature gt Hard Disk Boot Priority Virus Warning CPU L3 Cache Hyper Threading Technology Quiet Post Quick Power On Self Test USB Device Wait First Boot
73. odules on a bus will be reset O A MELSECWinCPU module and all the modules on a bus will be reset O Bus interface driver and all the modules on a bus will be reset O Available X Unavailable O A MELSECWinCPU module and all the modules on a bus will be reset After the completion of shutdown the main station becomes CPU DOWN condition and other stations detect multiple CPU DOWN error O A MELSECWinCPU module and all the modules on a bus will be reset After the reboot of OS the main station and the others detect multiple CPU DOWN error Then you should reset the 1st station O Bus interface driver and all the modules on a bus will be reset x On multiple CPU configuration you cannot reset even if you set a toggle switch to B RST No combination O A MELSECWinCPU module and all the modules on a bus will be reset After the completion of shutdown the main module becomes CPU DOWN condition and other stations detect multiple CPU DOWN error After the reboot of OS other stations detect multiple CPU DOWN error Then you should reset the 1 station O A MELSECWinCPU module and all the modules on a bus will be reset x On multiple CPU configuration you cannot reset even if you set a toggle switch to B RST The reset of the 1st station forces aMELSECWinCPU module and all the modules on a bus reset Then a MELSECWinCPU module becomes the condi
74. of Problems If after making and saving system changes with Setup you discover that your computer no longer is able to boot the AwardBIOS supports an override to the CMOS settings which resets your system to its defaults The best advice is to only alter settings which you thoroughly understand To this end we strongly recommend that you avoid making any changes to the chipset defaults These defaults have been carefully chosen by both Award and your systems manufacturer to provide the absolute maximum performance and reliability Even a seemingly small change to the chipset setup has the potential for causing you to use the override A Final Note About Setup The information in this chapter is subject to change without notice 23 4 BIOS Setup Main Menu Once you enter the Award BIOS CMOS Setup Utility the Main Menu will appear on the screen The Main Menu allows you to select from several setup functions and two exit choices Use the arrow keys to select among the items and press lt Enter gt to accept and enter the sub menu Note that a brief description of each highlighted selection appears at the bottom of the screen Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features gt Frequency Voltage Control Advanced BIOS Features Load Fail Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP PCI Configurations Sa
75. ombination with a programmable controller CPU and motion CPUs Module No 1 Programmable controller CPU Modules No 2 3 Motion CPU Module No 4 This product ooo00 ooo000 BER E EE loola loo aja a bhw YT This product Programmable controller CPU and motion CPUs I Up to 3 modules Module No 1 must be the Programmable controller CPU Install as the right most CPU An CAUTION The total number of programmable controller CPUs and motion CPUs installable is restricted by the power capacity of the Q Series power supply module Q61P When a large number of I O modules and intelligent function modules are used the equivalent restriction applies to them in the same way For details see Restriction by Power Capacity in Notes 84 Notes 6 Combination with the MELSEC Q Series Maximum Number of modules Installed and Maximum Number of I O Channels When installing single CPU configuration Refer to the maximum mountable number and the maximum I O number as follows Example of system expansion Maximum number of I O modules installed Maximum number of I O channels Maximum number of MELSECNET H modules installed Maximum number of CC Link modules installed Maximum number of interrupt modules installed Maximum number of other intelligent function modules in
76. on cable should be neither bundled with nor routed adjacent to the main circuit or power line The control line and communication cable should be at least 100mm away from the main circuit and power line Poor wiring conditions result in malfunctions caused by noise When the output module controls components such as the lamp load heater and solenoid valve a large current about 10 times the normal value may flow at the OFF to ON transition of the output Take appropriate measures for example by replacing it with a module of a higher rated current The period after a programmable controller CPU module turned on or got reset till a programmable controller CPU module attains the RUN condition is not fixed This period will change according to the system structure parameter settings the size of programs and so on Design the entire system to be protected even if the period till a programmable controller CPU module attains RUN would change Installation precautions A WARNING Use this product in the environment specified in this manual Using this product in the environment not satisfying all the specifications can cause an electric shock fire malfunction product damage and or product degradation Mount this product on the base unit with the module fixing hook at the bottom of this product fitted in the fixing slot in the base unit Failure to mount this product correctly can allow this product to malfunction or fall Befor
77. online power on conditions have limitations and each module respectively has the right procedure of its exchange For details refer to the pages of online module exchange described on QCPU User s Manual Hardware Design Maintenance and Inspection and the manuals of the modules supporting online module exchange Do not touch directly conductive area and electric components of the module It may lead to irregular operations and breakdown of the module When you use motion CPU modules or motion modules make sure that the combination of modules is correct after turning power on If the combination is irregular the product may get damaged For details refer to user s manual of motion CPU modules Wiring precautions A WARNING Before mounting or wiring this product or any other product be sure to turn the external power supply off for all phases Failure to turn it off for all phases may cause an electric shock product damage or malfunction After wiring you should install the terminal cover packed with the product before you turn power on and start operations If not you may get an electric shock A CAUTION Be sure to ground the FG and LG terminals by at least Class D Grounding former Class3 Grounding exclusive for programmable controller CPU Failure to do so may cause an electric shock or malfunction Be careful not to let foreign matter such as chips and wire tailings enter into this product Foreign matt
78. onnector does not support hot plugging The card should not be inserted or removed with the power supply ON You should not insert or remove the card or come into contact with it while the power is on Doing so may cause this product to malfunction or fail Before you insert remove the CF card make sure that the power is switched off and the access LED is turned off We have evaluated the operation of a CF card using the specific CF card listed on Chapter 9 List of Options and Recommended Parts The operation of other CF cards such as commercial ones cannot be guaranteed Built in SSD The product contains a SSD which has a capacity of 4GB The built in SSD is used for OS SSD has the rewritable life 1 million times Therefore a CF card is recommended for the data which will be rewritten frequently to be stored Write protect function This product has two types of write protect function EWF function of Windows Embedded Standard 2009 the function by software Write protect of DIP switch the function by hardware The write protect by EWF is sufficiently effective The combination of it and the DIP switch provides further reliable protect for writing However the DIP switch must be used in conjunction with EWF If you set the DIP switch for write protect to ON without setting EWF to Enabled OS will not boot Refer to following procedures for the setting How to set the DIP switch for write protect from OFF to ON 1
79. operating in a manner consistent with your own style of computer use Phoenix AwardBIOS CMOS Setup Utility Power Management Setup ACPI Function Enabled ACPI Suspend Type 1 POS Power Management User Define Video Off Method DPMS Videa Off In Suspend Yes Suspend Type Stop Grant Suspend Mode Disabled Reload Grobal Timer Events COM Port Disabled HPET Support Enabled HPET Mode 32 bit mode t 1 Move Enter Select PU PD Value F10 Save ESC Exit Fi General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 4 12 Power Management Setup 49 4 BIOS Setup Table 4 12 Power Management setup select ACPI Function Enabled ACPI Function ACPI Function cannot be changed Only Enabled is supported 1 Move ENTER Accept ESC Abort Note ACPI Advanced Configuration and Power Interface is a power management specification that makes hardware status information available to the operating system ACPI enables a computer to turn its peripherals on and off for improved power management It also allows the computer to be turned on and off by external devices so that mouse or keyboard activity wakes up the computer ACPI Suspend Type S1 POS a ACPI Suspend Type ACPI Suspend Type can not be changed Only S1 POS is supported ti Move ENTER Accept ESC bort Power Management Select how to set the Power Management function Power Management User D
80. ot Priority Virus Warning When enabled you receive a warning message if a program specifically a virus attempts to write to the boot sector or the partition table of the hard disk drive You should then run an anti virus program Keep in mind that this feature protects only the boot sector not the entire hard drive An CAUTION Many disk diagnostic programs that access the boot sector table can trigger the virus warning message If you plan to run such a program we recommend that you first disable the virus warning Enabled Activates automatically when the system boots up causing a warning message to appear when nable anything attempts to access the boot sector or hard disk partition table Disabled No warning message will appear when anything attempts to access the boot sector or hard disk isable partition table 32 4 BIOS Setup Table 4 5 Advance BIOS Feature select CPU L3 Cache Disabled CPU L3 Cache Enabled Select Disabled Enabled of CPU L3 Cache Selecting Enabled makes the speed of memory access higher 1 1 Move ENTER Accept ESC Abort Hyper Threading Technology Disabled Hyper Threading Technology Select Disabled Enabled of Hyper Threading Technology Quiet Post Enab led Disabled Select Disabled Enabled of Quiet Post Selecting Enabled makes the self test of a memory and some devices simpler Therefore the wake up time becomes shorter If selecting Disable
81. ou are booting up Windows do not shut it down The shutdown procedure may not be done in the correct order Specification Common Specification Single wire 24 to 16AWG Twisted wire 24 to 16AWG The standard length of peeled wire 10mm Available wire range R ded tool t trol E A minus driver diameter 3mm edge width 2 6mm Terminal block tightening torque 0 2 0 3Nm Use 60 75 C Copper Conductor Only Use a rod terminal as needed 68 Input part Input specification Current drive input insulated by photocoupler Input resistence 3 3kQ 1 External Circuit l 3 3kQ External Power Supply DC12V 24V i O Input Contact Figure 5 2 Input Circuit Output part Item Specification Open collector output insulated by photocoupler 1 Shutdown complete output becomes ON when the shutdown has finished 2 Watch dog timer start output becomes OFF when timeup has come Less than 1 5V output current lt 100mA Output specification Output condition Rest voltage of output ON Rating output Output response time External Circuit E Max DC30V i 25D780A 4 7kQ Figure 5 3 Output Circuit 5 Each Component Function 3 External Power Supply 69 5 Each Component Function Serial Port Interface SERIAL This product has one RS 232C compliant serial port
82. p Table 4 13 PCI PnP PCI Configuration Setup select Reset Configuration Data Dis abled Select Disabled Enabled of Reset Configuration Data Enabled Normally select Disabled If a fatal conflict happens and the operating system cannot boot after installing new addon and reconstructing system select Enabled ESCD Extended System Configuration Data will be reset after the setup ti Move ENTER Accept ESC Abort 53 4 BIOS Setup Resources Controlled By Auto ESCD Select Resource Controlled By Manual Resource Controlled By The Award Plug and Play BIOS can automatically configure all the boot and Plug and Play compatible devices If you select Auto ESCD all the interrupt request IRQ and DMA assignment fields disappear as the BIOS automatically assigns them ti Move ENTER Accept ESC Abort IRQ n Resources You can select IRQ Resources if you set Resouces Controlled By to Manual in PnP PCI Configuration Setup Selecting IRQ Resources the sub menu will be shown For details refer to the following If you want to control resources manually assign each system interruption to one of the following device types PCI Device The device which is compliant with Plug and Play standard and designed to support PCI or ISA bus architecture Reserved The device which is not compliant with Plug and Play standard and require the specific IRQ assignment Option PCI De
83. per or lower positioning limit 2 This product stops calculations and turns all outputs off upon detection of the following states The overcurrent or overvoltage protector of the power supply module has been actuated The self diagnostic feature of this product has detected an error such as a watchdog timer error If I O control transparent to this product causes an error all of the outputs may be turned on Provide this product with an external fail safe circuit or mechanism so that the machine operates on the safe side in that case 3 Depending on the fault of a relay or transistor in an output module the output may remain on or off For the output signals which can result in serious accidents provide external monitor circuits If an overcurrent continues to flow to the output for an extended period of time due to a rating error or short circuited load the output module may smoke or burn Provide an external safety circuit such as a fuse Configure the circuit containing this product so that the external power supply is turned on after this product is turned on Turning on the external power supply before this product may result in an output error or malfunction possibly causing an accident When you want to know the operating condition of each station when the network has had a communication error refer to manuals about the network In this case wrong output or wrong operation may cause accidents Any control line or communicati
84. play a message If a message is displayed it will be accompanied by PRESS F1 TO CONTINUE CTRL ALT ESC OR DEL TO ENTER SETUP POST Beep Currently there are two kinds of beep codes in BIOS This code indicates that a video error has occurred and the BIOS cannot initialize the video screen to display any additional information This beep code consists of a single long beep followed by two short beeps The other code indicates that your DRAM error has occurred This beep code consists of a single long beep repeatedly Position and Setting of CMOS ROM clear switch If an unexpected activation failure occurs due to the BIOS setting the CMOS ROM clear jumper can be set in order to disable the BIOS setting and start up the system In the normal operation leave the CMOS ROM clear jumper to the factory setting both OFF 1 First turn power off of the main body Then set CMOS clear switch DIP switch 1 SW1 to ON After 10 seconds set it to OFF again 2 Set ROM clear switch DIP switch 1 SW2 to ON 3 Turn power on of the main body and start the system After the system wakes up start the BIOS setup and set proper values to it 4 After the settings set ROM clear swich DIP switch SW2 to OFF again and save the settings Then reboot the system 61 5 Each Component Function 5 Each Component Function Component Name Front RDY LED Green B RUN LED Green Osrs CF SSD LED USER LED Red EXIT LED
85. ports data backup and rewrite from MELSECWinCPU built in SSD for OS or from a CF card to another CF card Refer to all devices to be used for backup as follows Table 10 3 List of Devices Display 2 USB keyboard SSS Used to reserve backup data 1 The capacity of the CF card for backup data should be larger than one of built in SSD Backup will be done by copying physical sectors Note that the number of physical sectors of each drive may be different even if the capacity of SSD is equal to one of a CF card Backup procedure How to backup the data of build in SSD for OS to another CF card 1 Connect a display and a keyboard to MELSECWinCPU Then insert a CF card to the slot 2 Turn power on and the system boots up The message Press DEL to enter SETUP will be shown at the left bottom corner of the screen Then press lt Del gt key and BIOS setup menu will be shown 104 10 Appendix 3 Select Advanced BIOS Features gt CF Backup Then press ENTER key Phoenix AwardBIOS CMOS Setup Utility Advanced BIOS Features gt CPU Feature Press Enter gt hard Disk Boot Priority Press Enter Virus Warning CPU L3 Cache Hyper Threading Technology Quiet Post Quick Power On self Test USB Device Wait First Boot Device Second Boot Device Third Boot Device Boot Ohter Device Boot Up Numlock Status Gate A20 Option Disabled Enabled Enabled Disabled Enabled Disabled
86. r error code 2100 SP UNITLAY ERR would happen c If you set more points than ones of mounted I O module You can not use the points exceeding the specified points of a mounted I O module d If you set different type from a mounted module You should set the same type to I O assignment setting as the actual mounted module If not it would work out of order If you use an intelligent function module you should set the same I O point No adding to above For results when the different type from the actual mounted module was set to an I O assignment setting refer to followings The list of results when I O assignment was different from the mounted module A mounted module ihe type ee assignment Result Input module High speed input module Output module T O mixing module Intelligent function module assignment error happens Error code 2100 S P UNITLAY ERR Output Works as input high speed I O mixing module K according to the actual type of the mounted module Output module Works as output I O mixing module T O mixing module according to the actual type of the mounted module Intelligent function module Input High speed input Intellligent function module assignment error happens Interruption module Output I O mixing Error code 2100 S P UNIT LAY ERR Input High speed input Output I O mixing Treated as a blank slot Intelligent Interruption All points becomes OFF Blank Treated
87. ration and Fuel devices Vehicles Manned transportation Equipment for Recreation and Amusement and Safety devices handling of Nuclear or Hazardous Materials or Chemicals Mining and Drilling and or other applications where there is a significant risk of injury to the public or property Packing List Thank you for purchasing this Mitsubishi product The product package contains the items listed below Check the contents of the product package If you discover any damaged or missing items contact the distributor J E CFJ CFE Er TE y s Connector cover for USB ea oe nt as a ae SW1PNC WCPU B Product Guide o Guide A AN u Zi Notes on Windows Embedded Standard 1 1 1 Precaution List 10 O pa gt er an aT Recovery Procedure o or O Recovery Media a 13M Contents SWIPNC WCPU B 2 4 1 MELSECWinCPU Module User s Manual Design Function Explanation and MELSECWinCPU Module Q Bus Interface Driver User s Manual Utility Operation Programming are included in SW1PNC WCPU B File path Manual For details refer to readme txt included in the left folder In order to read the above manuals you should prepare a PC installed with Adobe Reader MELSECWinCPU module cannot be used as it is not possible to install Adobe Reader and therefore cannot be used to read manuals User s manual is sold separately Purchase it separately Manual
88. rtant data Built in OS Windows Embedded Standard 2009 14 2 System Reference 2 System Reference Specification Table 2 1 Functional Specification 1 2 CPU Intel Atom Processor N450 1 66GHz Main memory 1GB 3 3V 200 pin DDR2 SO DIMM DDR667Socket x 1 Serial VF UF RS 232C RS 232C compliant Ich 9 pin D SUB connector baudrate 50 115200bps Ich 9 RS 232C compliant Ich 9 pin D SUB connector baudrate 50 115200bps D SUB connector baudrate 50 115200bps ni T 100BASE TX 10BASE T RJ 45 connector X 2 Controller Intel 82574L CFcard ee _ CF CARD Type I Only for the memory card of IDE connection Indication access LED green x 1 2 CFJ CFE models have a CFcard 4GB Built in SSD 3 Built in flash drive 4GB USB I F USB2 0 complicant 5ch front 3ch bottom 2ch Transfer rate 480Mbps Supply power 5V each channel 0 5A max 4 Watch dog timer 2ch Time up period system WDT 20msec 2sec user WDT 10msec 10sec General I O 5 6 Terminal block 1 2 Input for shutdown current drive input Terminal block 3 Output to notify shutdown completion open collector output Terminal block 4 Output to nofity the start of watch dog timer open collector output RTC CMOS Lithium battery backup life 10 years or more when no power input at 25 C BT The real time clock is accurate within 3 minutes at 25 C per month EXIT green CF SSD green Reset PUSH switch DIP switch 4 po
89. set the bus interface driver by resetting CPU Module No 1 programmable controller CPU Setting the toggle switch to B RST without resetting the CPU Module No 1 results in a multiple CPU down error on another CPU module 89 8 Troubleshooting 8 Troubleshooting Tips for Better Troubleshooting Key points for establishing a fastersystem is to minimize the number of problems developing and once a problem has developed identifying the cause as soon as possible You should perform troubleshooting with the following three basic points in mind 1 Check visually Check the following items 1 2 3 4 Behavior of external devices Existence or absence of power supply Wiring state connection cable LED indication Power indicator LED After checking the Module for items 1 4 connect the Module to external devices and check the behavior of the user program 2 Identify the problem Take the following steps to observe how the symptom changes 1 Change the input state to check whether the correct change can be read by the test program 2 Turning the output on and off repeatedly to check whether the state of the external device changes correctly 3 Narrow the range down Check the results of 1 and 2 above to locate the fault in one of the following options 1 2 3 4 This program side or external device side This program or any other Module Connection cable User program 90 8 Troubles
90. sibility 4 Move ENTER Accept ESC Abort 36 4 BIOS Setup BEEP Voice Enabled BEEP Voice Disabled Select whether or not BEEP sounds when the system boots up 1 Move ENTER Accept ESC Abort WDT Protect Select Enabled Disabled of WDT Protect Enabled Selecting Enabled WDT watches the system if the Dis abled connected devices would lose its control or the boot of BIOS would stop because of unexpected factors such as accidental noise When the boot of BIOS stops the reset will be processed and the system reboots Post Code Sh mn Enabled Select Enabled Disabled of Post Code Show Disabled Selecting Enabled the top right area of the screen shows Post Code when BIOS is booting But the display of Post Code will start after Graphic Device is initialized and the system is able to show images ty Move ENTER Accept ESC Abort CF Backup Selecting this option allows you to launch a tool for creating the backup of CF card and restoring it This can be used to backup your current environment as it is For details please refer to the explanation below 1 About the CF Backup Feature To use the CF Backup feature a separately available CF card for backup is required The CF card for backup must be larger capacity than built in SSD Using the CF card that is not our optional parts can be the cause of unidentified problems and it must be ensured that the CF card works with your s
91. stalled Main base unit Q312B 0 1 2 amp 3 9 10 11 lt Slot No in each slot A Power supply Expansion base 12 13 14 2 21 22 2 180 1A0 1C0 SSIS SISISISISISISIS 19F 1BF 1DF 1FF 21F 23F 2BF 2DF Power supply module Expansion base unit Q612B Added 24 25 26 27 28 29 30 3 E stage 5 y 52 A 32 channel module is installed Expansion base unit Q65B 53 54 55 56 440 680 69F 6A0 6C0I6EO 700 6BF 6DF 6FF 71F 36 37 38 39 40 41 stage 6 57 Power supply module ower supply module Expansion base unit Q68B xpansion base unit Q65B 58 59 60 61 4A0 4E0 500 520 56 720 gt 740 760 780 7A0 A 73F 75F 77F 79F 7BE xpansion base unit Q6 44 45 46 47 48 E 62 Power supply module E ower supply module Expansion base unit Q65B 63 7CO 7EO panqryorg penqryorg penqryorg 7FF Power supply module Power supply module Installation error Maximum number of nes stages added 8 64 modules 4 096 channels 64 modules 1 Up to seven expansion base units can be added 2 The total length of extension cables must be 13 2 m 3 When using an extension cable do not bundle it or route
92. t by registered devices 51 4 BIOS Setup Disabled Enabled Com Port Select Disable Enabled of COM port Disabled Enabled HPET Support Select Disable Enabled of HPET High Precision Event Timer Support 32 bit mode 64 bit mode HPET Mode Select HPET High Precision Event Timer Mode Normally select the proper value according to OS you use 1 Move ENTER Accept ESC Abort 52 4 BIOS Setup PnP PCI Configuration Setup This section describes configuring the PCI bus system PCI or Personal Computer Interconnect is a system which allows I O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings Phoenix AwardBIOS CMOS Setup Utility PnP PCI Configurations Reset Configuration Data Disabled Resources Controlled By Auto ESCD x IRQ Resources Press Enter INT Pin INT Pin 1 Assignment Auto 2 Assignment Auto INT Pin 3 Assignment Auto INT Pin 4 Assignment Auto INT Pin 5 Assignment Auto INT Pin 6 Assignment Auto INT Pin 7 Assignment Auto INT Pin 8 Assignment Auto 1 lt Move Enter Select PU PD Value Fi0 Save ESC Exit Fi General Help F5 Previous Values F amp Fail Safe Defaults F7 Optimized Defaults Figure 4 13 PnP PCI Configuration Setu
93. table minimal performance system operations Load Optimized Defaults When you press lt Enter gt on this item you get a confirmation dialog box with a message similar to Load setup Defaults Y N N Pressing Y loads the default values that are factory settings for optimal performance system operations Supervisor User Password Setting You can set either supervisor or user password or both of them The differences between them are SUPERVISOR PASSWORD can enter and change the options of the setup menus USER PASSWORD just can only enter but do not have the right to change the options of the setup menus When you select this function the following message will appear at the center of the screen to assist you in creating a password ENTER PASSWORD Type the password up to eight characters in length and press lt Enter gt The password typed now will clear any previously entered password from CMOS memory You will be asked to confirm the password Type the password again and press lt Enter gt You may also press lt Esc gt to abort the selection and not enter a password To disable a password just press lt Enter gt when you are prompted to enter the password A message will confirm that the password will be disabled Once the password is disabled the system will boot and you can enter Setup freely PASSWORD DISABLED When a password has been enabled you will be prompted to enter it every time you try to enter Setup
94. take inrush current into consideration Control Switch Reset switch Reset switch Push switch Hardware reset switch Pushing over 1 second make the product reset A CAUTION AX Use a control switch only when the product is showing no response because of abnormal behaviour etc If you use it on normal operations when OS is working the system may crash without a shutdown procedure Then the OS may not work properly after restart 72 5 Each Component Function 3 positions toggle switch B STOP me 77 B RST B RUN Figure 5 5 Factory Default of 3 position toggle switch Bus interface driver control switch 1 B RST Bus interface driver RESET Holding the toggle switch at the B RST position for two seconds resets the MELSEC Q Series modules under control of this product and the bus interface as well Use this switch to reset only the MELSEC Q Series modules instead of causing a hardware reset of the entire system including this product y 3 position Toggle switch z B STOP Bus interface driver STOP Stops of the operation of the bus interface driver prevents user applications from issuing access to the modules on the bus and turns the Y output 2 off Module diagnostic utilities such as forced Y output and buffer memory batch monitor can be executed B RUN Bus interface driver RUN Makes the bus interface driver active allowing user applications to access modules on the bus 1 The bus int
95. ter the sub menu of IDE Channel 0 Master Options are in its sub menu detailed options Press lt Enter gt to enter the sub menu of IDE Channel 0 Slave Options are in its sub menu detailed options 2 er Press lt Enter gt to enter the sub menu of IDE Channel 1 Master Options are in its sub menu detailed options EGA VGA Video ee Select the default video device CGA 80 MONO All Errors Select the situation in which you want the Halt On No Errors BIOS to stop the POST process and notify All But Keyboard you Displays the amount of conventional Displays the amount of conventional Base Memory memory automatically memory detected during boot up Displays the amount of extended Displays the amount of extended memory Extended Memory memory automatically detected during boot up Displays the amount of total memory Displays the total memory available in the Total Memory y automatically system 27 4 BIOS Setup IDE Adapters The IDE adapters control the hard disk Use a separate sub menu to configure each hard disk Use the legend keys to navigate through this menu and exit to the main menu Use Table 4 3 to configure the hard disk Table 4 3 IDE Adapters configurations Press Enter to auto detect the hard disk on this channel IDE HDD Auto Detection Press Enter If detection is successful it fills the remaining fields on this menu Selects the type of fixed disk User Type will let you IDE Cha
96. the module in the direction of the arrow to mount the module on the base unit Unit fixing hook Fiture 3 1 Installing the Module 1 A CAUTION _ _____ __ gt Be sure to turn off the power to this product before installing it To use this product in a place subject to much vibration or shock use two screws to fasten it to the base unit as illustrated below Module fixing screws M3 x 12 Prepared by the user Tighten the screws within the following torque range Tightening torque range 36 48N cm Figure3 2 Installing the Module 2 19 3 Hardware Setup Uninstalling the Module If this product has been fastened with module fixing screws remove them first 1 While pressing the protrusions 2 on top of this product pull this product toward you by the upper side 3 Lift this product to remove the module fixing hook from the module fixing slot 4 LLL Figure 3 3 Uninstalling the Module An CAUTION Be sure to turn off the power to this product before uninstalling it If the OS is still up and running when you attempt to turn the power off shut down the OS before turning the power off Installing the fitting to fix a CF card After the insertion of a CF card install the fitting to fix a CF card as follows LLL Figure 3 4 Installing the fitting to fix a CF card 3 Hardware Setup The hole to attach th
97. their needs Supervisor Password Use this menu to set Supervisor Passwords User Password Use this menu to set User Passwords Save amp Exit Setup Save CMOS value changes to CMOS and exit setup Exit Without Save Abandon all CMOS value changes and exit setup 25 4 BIOS Setup Standard CMOS Features The items in Standard CMOS Setup Menu are divided into 10 categories Each category includes zero one or more than one setup items Use the arrow keys to highlight the item and then use the lt PgUp gt or lt PgDn gt keys to select the value you want in each item Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Time hh mm ss 16 18 28 Item Help Menu level DP IDE Channel 0 Master None IDE Channel 0 Slave None Change The day month IDE Channel 1 Master None year and century Video EGA VGA Halt On All But Keyboard Base Memory 639K Extended Memory 1038336K Total Memory 1039360K 1 lt Move Enter Select PU PD Value F10 Save ESC Exit Fi General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 4 2 Standard CMOS Features 26 4 BIOS Setup Main Menu Selections This table shows the selections that you can make on the Main Menu Table 4 2 Main Menu Selections Set the system date Note that the Day Date Month DD YYYY automatically changes when you set the date HH MM SS Set the system time a de Press lt Enter gt to en
98. tion without any power If OS is working it means that you finished the system without shutdown procedure and OS may not work in order after the next reboot 87 7 Reset Specifications Reset Procedure of a MELSECWinCPU module and All the Modules on a Bus Reset by Recycling the Power Supply 1 Shut down the OS on the screen or set the shutdown command input to ON 2 Check that the EXIT LED on this product comes on or that the shutdown completion output is turned ON 3 Turn the power off 4 Turn the power back on Restarting the OS DIP switch 2 with SW 5 set to OFF 1 Shut down the OS on the screen then restart it 2 In the multiple CPU configuration reset CPU Module No 1 after the completion of OS boot up Reset of Module No 1 programmable controller CPU DIP switch 2 with SW 5 set to ON 1 Reset the switch on Module No 1 An CAUTION Be sure to give ON time of a shutdown directions input as a range of 0 7sec 3sec If3 or more secs are turned on re starting of a MELSECWinCPU module will become impossible The time of a re injection of a power supply is included When this operation is performed and re starting of a MELSECWinCPU module becomes impossible you can re start the MELSECWinCPU module by setting the shutdown command input to OFF and then inputting the shutdown command again ON time 0 7sec 3sec in the state of the power turned ON The MELSECWinCPU module cannot be re stated simply
99. ts built in SSD to be writtten in Refer to Chapter 5 Built in SSD 1 When changing SW 1 3 4 of DIP switches check that power of the product is OFF While power is ON don t change DIP switches 2 You change set SW 1 to ON only when power of the product is OFF If power of the product is ON and SW 1 is ON it does not work in order Before turning ON power of the product be sure to check that SW 1 is OFF dip switch DIP Switch 2 COS 123456 Figure 5 6 Factory Default of DIP switch 2 CET IS Rn Reserved Factory default OFF Reserved Factory default OFF Reserved Factory default OFF Reserved Factory default OFF ON Setting the RESET L CLR switch on module No 1 programmable controller CPU to RESET resets this product 3 BEZ Reserved Factory default OFF 1 Before making changes to DIP switch settings turn off the power to this product Do not touch any DIP switch 5 SW 5 PR Reset method select switch Factory default OFF en shae When this product is module No 2 4 in the multiple CPU system 1 DIP switeh OFF Setting the RESET L CLR switch on module No 1 programmable controller CPU to RESET resets the bus interface driver without resetting this product 2 setting with the Module powered 2 Usually leave SW 5 set to OFF If you set SW 5 to ON the reset operation on Module No 1 resets this product as well If the OS is still up and running at that time the reset causes the OS to a
100. tting is set to Enabled you become able to set this item 1 Move ENTER Accept ESC Abort 35 4 BIOS Setup Typematic Delay Wsec Typematic Delay Msec Select Typematic Delay You can select the waiting time for continuous typing If the item Typematic Rate Setting is set to Enabled you become able to set this item Security Option Select Security Option when the security setting is enabled Selecting Setup system will boot up but the access to the setup will be denied unless you input the correct password to its prompt Selecting System system will not boot up and the access to the setup will be denied unless you input the correct tL Move ENTER Accept ESC Abort password to its prompt Note To disable security select PASSWORD SETTING on the Main Menu and then you will be asked to enter password Do not type anything and just press lt Enter gt it will disable security Once the security is disabled the system will boot and you can enter Setup freely APIC Mode Enabled APIC Mode You can not change this item Advanced Programmable Interrupt Controller is fixed to Enabled tJ Move ENTER Accept ESC Abort MPS Version Control For OS Select MPS Version Control For OS Select the version of multi processor platform Selecting 1 4 the system get the support for multi PCI bus configuration and the extended configuration table for the future exten
101. uting It can boot from a built in SSD and a CF card in a CF card slot Type I This product has two LAN ports They can be used to build systems for Web Internet and Intranet Embedded type CPU and chipset have been adopted The use of readily available parts ensures the ease of the use of the product In addition the use of self customized BIOS allows support to be provided at the BIOS level Features MELSEC Q Series programmable controller CPU modules cover sequence controlling This MELSECWinCPU module covers computing The combination of them realizes the seamless processing of information and control data Very small Windows OS system 2 slot size of a MELSEC Q series programmable controller CPU Adopts Intel Atom processor N450 belonging to energy saving platform It manages both enough performance and energy saving or has low power consumption while maintaining adequate performance Various interfaces are installed as the standard OOOBASE T LAN USB2 0 CF card slot and so on The use of Contec customized BIOS mfd By Phoenix Award allows the support provided at the BIOS level A CF card can be installed as an external storage device The use of it is preferable if it works where shock and vibration exist and is ideal for long periods of continuous operation Built in SSD has double write protect functions an EWF function of OS and write protect function of DIP switch It provides more reliable protection for impo
102. ve amp Exit Setup PC Health Status Exit Without Saving ESC Quit tTl lt Select item Save amp Exit Setup SAVE CMOS TO BIOS F7 LOAD CMOS FROM BIOS Time Date Hard Disk Type Figure 4 1 Main Menu Setup Items The main menu includes the following main setup categories Standard CMOS Features Use this menu for basic system configuration Advanced BIOS Features Use this menu to set the Advanced Features available on your system Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your system s performance Integrated Peripherals Use this menu to specify your settings for integrated peripherals 24 4 BIOS Setup Power Management Setup Use this menu to specify your settings for power management PnP PCI Configuration Use this menu to specify your settings for PnP PCI PC Health Status Use this menu to show the environmental status of your system Frequency Voltage Control Use this menu to set the frequency and the voltage of system Load Fail Safe Defaults Use this menu to load the BIOS default values for the minimal stable performance for your system to operate Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations While Award has designed the custom BIOS to maximize performance the factory has the right to change these defaults to meet
103. vice Reserved Phoenix AwardBIOS CMOS Setup Utility IRQ Resources Assigned Device Assigned Device Assigned Device Assigned Device Assigned Device Assigned Device Assigned Device Assigned Device Assigned Device Assigned Device 1 lt Move Enter Select PU PD Value F10 Save ESC Exit Fi General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 4 14 IRQ n Resources 54 4 BIOS Setup Table 4 14 PCI PnP PCI Configuration Setup select Description INT Pin 1 Assignment Auto INT Pin 1 Assignment Select INT Pin 1 Assgnment Devices s using this INT Network Controller Bus 1 Dev 0 Func 0 Display Controller Bus 0 Dev 2 Func 0 USB 1 0 1 1 UHCI Controller Bus 0 Dev 26 Func 0 INT Pin 2 Assignment to INT Pin 2 Assignment Select INT Pin2 Assignment Devices s using this INT Network Controller Bus 2 Dev 0 Func 0 INT Pin 3 Assignment Select INT Pin 3 Assignment Devices s using this INT USB 1 0 1 1 UHCI Controller Bus 0 Dev 29 Func 2 USB 2 0 EHCI Controller Bus 0 Dev 26 Func 7 TiMove ENTER Accept ESC Abort 55 4 BIOS Setup INT Pin 4 Assignment INT Pin 4 Assignment Select INT Pin 4 Assignment Devices s using this INT IDE Controller Bus 0 Dev 31 Func 2 USB 1 0 1 1 UHCI Controller Bus 0 Dev 29 Func 1 SMBus Controller Bus 0 Dev 31 Func 3 INT Pin 5 Assignment to INT Pin 5 Assignment Select INT Pin
104. ystem without problem before using this feature Also before performing backup read the licensing terms of your operating system carefully so that the backup is carried out within the scope of given license For the detailed procecure of CF Backup Feature refer to Appendix 5 Backup of built in SSD 37 4 BIOS Setup Advanced Chipset Features Setup This section allows you to configure the system based on the specific features of the installed chipset This chipset manages bus speeds and access to system memory resources such as DRAM and the external cache It must be stated that these items should never need to be altered The default settings have been chosen because they provide the best operating conditions for your system The only time you might consider making any changes would be if you discovered that data was being lost while using your system Phoenix AwardBIOS CMOS Setup Utility Advanced Chipset Features DRAM Timing Selectable CAS Latency Time DRAM RAS to CAS Delay DRAM RAS Precharge Precharge delay tRAS System Memory Frequency System BIOS Cacheable Memory Hole At 15 16M VGA Setting On Chip Frame Buffer Size DVMT Mode Total GFX Memory By SPD Auto Auto Auto Auto By SPD Enabled Disabled 8MB Enable 128MB t 1 lt Move Enter Select PU PD Value F10 Save ESC Exit Fi General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 4 6 Adv

MELSECWinCPU Module User`s Manual(Hardware

Contents

Download Pdf Manuals

Related Search

Related Contents