SCOTT 2014 BIKE OWNER`S MANUAL
Contents
1. Tapered 054 9mm 11 8 44mm It is also possible to use forks with a standard 11 8 steerer tube when using a reducer headset for example 2 A straight 11 8 headset and fork steerer system to match with semi integrated headsets with an ID on the headtube of 44 0mm on top and lower end This is a standard part in the market and should be available from several parts manufacturers BOTTOM BRACKET BB ON SPARK All carbon front frames of Spark have a BB shell for BB92PF standard This matches to several bearing and crankset models of Shimano SRAM FSA and others The alloy front frames of Spark have a BB shell for BB92PF or 73mm BSA standard depending on the model ENGLISH SPARK ADJUSTABLE BB HEIGHT On Spark bikes equipped with the FOX Nude 3 FOX Float CTD shock you can adjust the BB height above ground in 2 positions by flipping a geometry chip located on the linkage bar shock mount Please note the max tightening torque of 10Nm 88 in Ibs ew 1 low BB for lower center of gravity over ground slacker head angle 2 high BB for bigger clearance between pedals crankset and obstacles on the ground steeper head angle Spark 700 Spark 900 LOW POSITION HEAD ANGLE 68 3 69 5 BBHEIGHT 330mm 37mm HIGH POSITION HEAD ANGLE 68 8 70 26 sco7TrTr BIKE OWNER2. PO34 Front Fork Set Up Change of Front Fork PO37 PivorMaintenance i rime PO37 DA ELA CS AUS ARR PO38 x lt 2 4 SPARK CONCEPT The new Spark is the result of 2 years of research and development for one of the lightest mountain bike frame set available on the market hitting the scale at below 1800 grams 4 lbs including the frame FOX Nude shock and the unique TWINLOC remote control SCOTT S focus was not only on lightweight but also on a durable and stiff frame with an innovative suspension technology in combination with an optimized kinematics of the rear swingarm The combination of an optimized kinematics with an extraordinary suspension technology closes the gap between superlight hardtail bikes e g SCOTT Scale and the new generation of marathon trail bikes e g SCOTT Genius Spark was designed for riders looking for a dual suspended race and marathon bike offering a maximum rear wheel travel of 120mm 27 5 100mm 29 SCOTT does not see frame and rear shock as single components which are assembled together on a bike but as a concept with all these components working together and offering an outrageous function by matching perfectly The Spark Concept is based on a multi pivot technology The damping performance was improved in comparison to the already famous old Spark and with reworking also the kinematics we were able to reach
3. SCOTT 2014 BIKE OWNER S MANUAL SCOTT SPORTS SA 17 RTE DU CROCHET 1762 GIVISIEZ SWITZERLAND 2013 SCOTT SPORTS SA ALL RIGHTS RESERVED SCOTT SPORTS COM DISTRIBUTION SSG EUROPE DISTRIBUTION CENTER SA P E D ZONE C1 RUE DU KIELL 60 6790 AUBANGE BELGIUM V3 2 20130710 GLOTT OGLOTT Slit The Spark should be adjusted exactly to the individual rider to achieve maximum safety and fun while riding All adjustments should be done at a local SCOTT dealer or by strictly following this manual In order to avoid any harm or in the case of technical problems or doubts please contact your authorized SCOTT dealer CONTENT Spark CONCEDt cde senorna e AAEE EN pena teenie ta taeda POO4 Geometry Technical Data Spark 275 65 5 Geometry Technical Data Spark 29 P 006 TC Shock Technology TWINLOC POO7 Basic Set Up of the TWINLOC Remote Control PO14 Recommended Tools for the Shock Set Up P 018 Set Up Spark with FOX Nude P 019 Spark Cable ROUUNG VEEE Gi cso P 028 Adjustment of Seatpost Height P 034 Replaceable Drop Out
4. S MANUAL IMPORTANT It is not possible to use this geometry chip with other shock models than the FOX Nude FOX Float CTD The shock might collide with parts of the frame or linkage bar Models originally equipped with another shock than the FOX Nude FOX Float CTD will have a chip with a centered shock bolt hole FRONT DERAILLEUR FD MOUNTING DETAILS On all Spark frames you will find a Shimano E type front derailleur but fixed directly on the swingarm without the plate that is fixed normally between the bottom bracket bearing cup and the bottom bracket housing of the front triangle or a SRAM Direct Mount Type S3 FD Please note that you always need to use the adapter plate attached to the bike or frame set between chainstay and front derailleur The FD adapter plates of Spark 700 and 900 series are NOT interchangeable Spark 900 new FD adaptor for MY14 This adapter can be ordered at the SCOTT distribution with parts number 207 235278 FD mount plate Set Spark 900 2014 ENGLISH SPARK scott sports com 27 SPARK CABLE ROUTING The direct and straight cable system on all our full suspension models offers perfect shifting performance combined with minimal weight and high resistance against water and dirt CARBON FRONT FRAMES The carbon frames of Spark have an internal shifting cable routing with cable stops on the front end of the downtube as shown in the drawing below 28
5. Gscorr BIKE OWNER S MANUAL Please note that the inner cables need to cross each other 1 time on the inside of the downtube before you pull them out through the cable slot on the lower downside of the downtube Push the cables through the cable guide as shown below and fix the cable guide on the downtube with a 3mm allen key and a tightening torque of 4Nm 35in lbf scott sports com 29 ENGLISH SPARK Push the outer cable housings on the cables into the cable guide but make sure to respect the needed length as shown in the next drawing Please make sure to respect the 40mm distance between the cables and the BB bottom bracket housing to avoid ghost shifting and or damages on the shift cables and brake hoses 30 Gscorr BIKE OWNER S MANUAL For the rear brake please assemble the cable as shown in the following diagrams Please remember to maintain a minimum distance of 40mm between the brake hoses and the BB housing as mentioned previously Use the plastic guide to fix the brake cable The cable guide can be ordered via SCOTT distribution with parts number ies a ey o scott sports com 31 ENGLISH SPARK ALLOY FRONT FRAMES Please fix the cable housings and the brake hose on the frame on the cable mounts with cable zippers by following the routing information as shown below Please make sure to respect the 40mm distance between the cables and the
6. 0mm if the distance between the main dust wiper seal is greater than 10mm the air pressure of the air chamber is too low and should be increased by using the shock pump until the distance is 10mm 20 Gsco7TrTr BIKE OWNER S MANUAL SET UP OF REBOUND FOX NUDE OR FOX CTD SHOCK Rebound describes the speed the shock comes back to its original length after absorbing an obstacle By using the rebound adjuster knob S4 you can adjust the rebound step by step Please refer to the following instructions Ride your bike off a pavement remain in the saddle and check how many times it bounces If it bounces 1 2 times the set up is good If it bounces more than 3 times the rebound is too fast Turn the knob 1 2 clicks clockwise If it does not bounce the rebound is too slow Turn the knob 1 2 clicks counter clockwise scott sports com 21 ENGLISH SPARK Note that you have to mount the FOX Nude Shock always as shown underneath Mounting the rear shock in a different position can cause severe damages to the frame the linkage levers and the rear shock Same for the FOX Float CTD and X Fusion El shock on some of the Spark models After dismantling the rear shock both fixing bolts should be tightened with a tightening torque of I0Nm 88in lbs If this is not done correctly the rear shock may become damaged Please only use SCOTT shock bolts and follow the assembly instructions sho
7. 2 right side replaceable RD hanger available with 219575 scott sports com 35 ENGLISH SPARK REAR DISC BRAKE MOUNT Spark can be used with 3 different disc rotor sizes on the rear brake The rear disc brake on Spark is Postmount PM Standard on the left seatstay and it is possible to use disc rotors with 160 180 and 185mm diameter Please note that for the assembly of 180 and 185mm rotors you may need adapters washers between the PM port on the frame and the brake calliper FRONT FORK SET UP CHANGE OF FRONT FORK For the front fork set up please use the fork specific manual attached to the bike We recommend using front forks with a travel of 120mm 27 5 and 100mm 29 as this will not influence the geometry or alter the handling of the bike For details on the technical length of the recommended forks please refer to the Tech Info Chart mentioned previously PIVOT MAINTENANCE The pivot and bearings on SCOTT Spark are extremely easy to maintain An external treatment with a grease spray after every bike wash is all you have to do We do not recommend heavy grease sprays since these will leave a film on the parts which is difficult to remove We recommend the same for the chain also If you have to change the bearings you can order them included in a service kit at your local SCOTT dealer or buy them with international parts number as shown above in the specs list in a hardware store In case of a chang
8. 5 ENGLISH SPARK GEOMETRY TECHNICAL DATA SPARK 29 2 63 Piston stroke 38mm nn 7 ee Eve to Eye Hardware 222mm x 8mm Hardware 22 2mm x 8mm SWINE snus Seatpost 31 6MM diameter 2 oe Headset semi integr for tapered 1 1 8 1 5 44 54 9mm inner diameter of frame or ar With 118 straight 44 0mm Fork travel 100mm Fork length 506mm BB housing BB PF 92 carbon 73mm alloy Front Shimano E Type SRAM S3 direct Bearings 2 x IGUS 6 x 6802 24x15x5 Max tire width 57mm 2 25 SPARK 29 BHEADTUBELENGTH TOPTUBE LENGTHHORZONTAL _ D TOPTUBE LENGTH ACTUAL BB CENTER TO TOP OF SEATTUBE BB CENTER TO TOPTUBE CENTER 336mm 1 539mm 212in it 751 440mm 173in 350mm 38n H CHAINSTAY LENGTH 448mm 176in AN REN E apm ren Mamm Ton M Re EE WHEELBASE 163mm 458in RE ee an LSTAK 625mm 246in ee ES Ces 6 G corr BIKE OWNER S MANUAL SHOCK TECHNOLOGY The heart of the TC System is the FOX Nude Shock offering three functions which make this system possible The TWINLOC remote control lever is the evolution of the already outstanding TRACLOC system of SCOTT While TRACLOC allowed only the change on the SCOTT TC rear shocks between the SCOTT patented climb traction and full mode on the fly from the handlebar the
9. BB bottom bracket housing to avoid ghost shifting and or damage to the shift cables and brake hoses For the rear brake please assemble the cable as shown in the following diagrams Please remember to maintain a minimum distance of 40mm between the brake hoses and the BB housing as mentioned previously Use the plastic guide to fix the brake cable The cable guide can be ordered via SCOTT distribution with parts number ENGLISH SPARK ADJUSTMENT OF SEATPOST HEIGHT The seatpost has to be inserted at a minimum of 100mm into the seattube Never use a seatpost diameter other than 31 6mm or try to use a shim reducer between the seatpost and frame REPLACEABLE DROPOUT On Spark bikes of model year 2012 you can replace the rear derailleur hanger Depending on the different models you ll find the following options 1 142mm axle with RWS 142 12 The complete set is available via SCOTT distribution with parts number 219574 the right side replaceable RD hanger with 219577 34 scorr BIKE OWNER S MANUAL 2 Regular 135 mm rear axle with standard QR The replaceable hanger is available via SCOTT distribution with parts number 206473 If you use other RWS standards we can offer after market parts for specific wheelsets with the following parts via SCOTT distribution RWS 135 12 parts set 219574 right side replaceable RD hanger available with 219576 _ RWS 135 5 parts set 21957
10. FOX Nude shock functions perfectly it is very important to strictly follow the below steps On Spark Carbon frames you will find an internal cable routing Push the inner cable first through the remote lever in the upper cable routing of the lever and then through the cable housing inside the toptube as shown below On Spark alloy frames a regular outside cable routing the outer cable housing is fixed on cable mount ports with cable zippers 14 Gscorr BIKE OWNER S MANUAL 1 Loosen the cable fixing screw S7 by turning it counter clockwise with a 2mm allen key 2 Insert a new cable via the lever hole and cable housing and push it into the shock around the remote wheel S6 as shown scott sports com 15 ENGLISH SPARK 3 Tighten the cable and fix the cable fixing screw S7 by turning it clockwise with a 5 Cut the cable approx 20mm away from the remote wheel 2mm allen key and max tightening torque of 1 6Nm Fix it by squeezing it with pliers 4 Check that the handlebar lever is in the traction position Refer to the diagram below Fix it by squeezing it with pliers 16 Gsco7TrTr BIKE OWNER S MANUAL 6 Push a cable end cap on the cable until it touches the end of the cable scott sports com 17 ENGLISH SPARK BASIC SET UP THE TWINLOC REMOTE CON TROL OF FOX FLOAT CTD SHOCK The assembly of the remote cable and the setup of the FOX Float CTD rear shock is
11. TWINLOC allows also the remote control of the front fork to shift between lock out and open mode at the same time when you change the modes on the SCOTT rear shox In combination with SRAM RockShox DNA 3 or FOX CTD forks it is also possible to have a traction mode on the fork The 3 modes of CTCD in combination with FOX Nude are CLIMB OUT MODE Climb rear climb front TRACTION MODE Traction mode rear incl geometry change and reduced travel platform mode front DESCENT MODE Full travel rear full travel front The 3 modes of CTD in combination with FOX CTD are CLIMB OUT MODE Climb rear climb front RIDE MODE Platform ride mode rear platform mode front DESCENT MODE Full travel rear full travel front Therefore SCOTT offers 2 different TWINLOC levers with following fork rear shock combinations FOX Nude with different rolls for FOX CTD fork and RockShox DNA 3 fork SCOTT Article number 230097 FOX CTD with different rolls for FOX CTD fork and RockShox DNA 3 fork SCOTT Article number 230098 ENGLISH SPARK Please note that the FOX CTD rear shock does not offer a traction mode but a ride mode featuring a platform In contrary to FOX Nude the air chamber volume of the positive chamber remains the same throughout the different modes scott sports com 7 8 IMPORTANT You can only assemble the TWINLOC remote lever in left side upward position on the handlebar You have 3 positions of t
12. a better progression in the end of the stroke travel of the swingarm The SCOTT system named TC Traction Control will allow you to reduce by remote control the rear wheel travel from 120 27 5 100 29 mm to 85 27 5 70 29 mm including a more progressive spring rate but still offering a supple break away No power will be lost and an optimum power transfer is guaranteed as the swingarm in contrary to locked or automatic locking systems can follow the trail surface and will offer perfect traction and higher speed while standing on the pedals Gsco7TrTr BIKE OWNER S MANUAL GEOMETRY TECHNICAL DATA SPARK 27 5 650B ra a a Suspension Ratio 240 Piston stroke 50mm Eye to Hardware 22 2mm 8MM Mainframe Hardware 22 2mm x 8mm SWINQANM nn Seatpost 31 66mm diameter k O Headset semi integr for tapered 1 1 8 1 5 44 54 9mm inner diameter of frame or with 11 8 straight OO Fork travel 120mm Fork length 507mm BB housing BB PF 92 carbon 73mm alloy Front derailleur Shimano E Type SRAM S3 direct mount m ns ope s SPARK 275 650B HEADTUBE LENGTH TOmm CTOPTUBELENGTHHORIZONTAL 553mm 21 650mm 256in me D TOPTUBE LENGTH ACTUAL F BB CENTER TO TOP OF SEAI UBE H CHAINSTAY LENGTH BBHEIGHT WHEELBASE L STACK 735 540mm 213in scott sports com
13. consistent with the use originally intended for the bicycle as sold are not covered by this warranty Hereby SCOTT grants a voluntarily manufacturer s warranty Additional entitlements according to national warrant of merchantability are reserved For warranty info on the Fox Nude shock please refer to the attached manual of Fox Nude ENGLISH SPARK scott sports com 39
14. e of the bearings or of the rear swingarm you should contact your local SCOTT dealer as you need special tools for disassembly and assembly ENGLISH SPARK WARRANTY Frame NG SHOCKING indemne dedans eee D t Or p rChas 38 G corr BIKE OWNER S MANUAL WARRANTY SCOTT bikes are made using the most innovative production and quality methods They are equipped with best components of well known parts suppliers Doing so SCOTT warrants its frames and swingarms for five years subject to compliance with maintenance ranges see below and SCOTT forks provided it is a fork of SCOTT for two years for defects in material and or workmanship in case of purchase of completely assembled bikes This warranty of 5 years for the frames shall only be granted in case once a year a maintenance service has been effected according to maintenance requirements as set forth in this manual by an authorised SCOTT dealer The authorised SCOTT dealer shall confirm the effected annual maintenance service by stamp and signature In case such an annual maintenance service has not been effected the warranty of 5 years for the frame shall be reduced to 3 years Costs for maintenance and service have to be born by the owner of the SCOTT bike On Gambler Voltage Fr and Volt X the warranty period is limited to 2 years The warranty peri
15. en you make a check of the air pressure of the shock Pls also note that the indicators of shock pumps have a tolerance of max 10 4 pump the recommended pressure into the shock Please use the FOX iRD App available at itunes App store with following link https itunes apple com us app fox intelligent ride dynamics id549035102 mt 8 amp ign mpt u0 3D4 5 After downloading the app on your mobile gear please follow the steps shown in the app and inflate the shock according to the air pressure indicated FOX Intelligent Ride Dynamics ENGLISH SPARK 6 when you reached the needed pressure remove the pump and put the valve cap on the valve scott sports com 19 SAG The SAG should be 10mm on the shock piston To check the adjustment please follow the below instructions 1 2 Sit on the bike put your feet on the pedals Put your feet back on the ground and stand over the bike without bouncing the bike during this action Check if the o ring S9 on the shock piston S8 has a distance of 10mm to the main dust wiper seal between shock housing and piston if the distance between the o ring and the main dust wiper seal is 10mm the air pressure is correct for your weight if the distance between the o ring and the main dust wiper seal is less than 10mm the air pressure of the air chamber is too high and should be carefully reduced by using the bleed knob of the shock pump until the distance is 1
16. he TWINLOC remote lever 1 CLIMB MODE The shock is nearly locked climbing on asphalt roads is now possible without any power loss Simultaneous a blow off system prevents the shock being damaged in case the rider did not open the system while crossing obstacles 2 TRACTION MODE RIDE MODE For Traction by reducing the internal chamber volume inside the shock the travel of the shock will be reduced to around 80 approx 96 80mm the characteristic of the air spring gets harder the SAG is shorter and the geometry steeper This results in climbing without bobbing and offers still optimum traction of the rear wheel For Ride by adding a platform on the compression damping system the shock will not bounce while standing on the pedals 3 DESCENT MODE Full travel of 120 100mm 27 5 29 You will find the following positions on the remote lever LOCK OUT MOD TRACTION MODE RIDE MODE DESCENT MODE PRESS TO RELEASE G corr BIKE OWNER S MANUAL For the assembly of the remote control of the front fork lock out 2 different cable rolls which are changeable are existing The different roll for the pull of the fork remote cable can be changed within few minutes to adapt the lever to your fork model brand You will see on the downside of the roll the indication of the fork brand or the fork model Scott offers 2 different TWINLOC levers with following fork rear shock combinations FOX Nude with different rol
17. k cable Rock Shox Fork Fix the cable with the 2mm allen screw on the barrel adjuster on the fork crown with a tightening torque of 0 9Nm 8 Ib in cut the cable and secure it with a cable end cap Please refer for this action also to the manual of SRAM RockShox or FOX attached to the bike TIP To check for accurate cable tension please try to move the plastic end cap of the cable housing at the barrel adjuster on the remote lever There should be no play between cap and barrel adjuster ENGLISH SPARK In case of play please turn the barrel adjuster clockwise until no play scott sports com 11 FOX NUDE SHOCK AND TWINLOC REMOTE CONTROL LEVER In the diagram of the shock and remote lever shown below you will see the parts indicated with numbers which will be used in the manual for the adjustment and set up 12 Gsco7TrTr BIKE OWNER S MANUAL Parts List 51 52 55 54 55 56 57 58 59 L1 L2 IES L4 ES Front eyelet Shock Bolt Rear eyelet Shock Bolt Shock Housing Rebound Adjuster Knob Positive Chamber Valve Remote Control Wheel Cable Fixing Screw hidden behind remote wheel Shock Piston SAG Indicator o ring on piston Remote Lever Release button Remote Control Cables Cable Tension Screw Fork Remote Cable Tension Screw Shock Remote scott sports com 13 ENGLISH SPARK BASIC SET UP THE TWINLOC REMOTE CON TROL OF FOX NUDE SHOCK To ensure the
18. ls for FOX CTD fork and RockShox DNA 3 fork Scott Article number 230097 FOX CTD with different rolls for FOX CTD fork and RockShox DNA 3 fork Scott Article number 230098 Please kindly note that the cable roll of a RockShox DNA3 or FOX CTD fork lever is not interchangeable with the regular rolls of 2 step forks You need to use another lever For details on this please contact your authorized Scott dealer ENGLISH SPARK scott sports com 9 To change the rolls to match another fork brand please follow the diagrams below ROLL FORK UNMOUNTING f DT FOX J FORKS ROLL FIXATION J DT SHOT ff FOX CTD ROCK SHO X FORKS ROLL FIXATION ROLL FORK MOUNTING 10 GscorT BIKE OWNER S MANUAL 2mm allen ASSEMBLY OF THE REMOTE CABLE SRAM ROCKSHOX FORKS Please make sure the lockout of SRAM RockShox or FOX fork is activated after transport correctly Therefore please compress fork 5 10 times before following the manual on remote cable installation and adjustment The lever should show on the downside of the cable roll the brand name of the fork you are going to use Please do not try to use a RockShox roll with a FOX fork or vice versa To assemble the cable please bring the lever into the Descent Mode push the cable into the lever eyelet as shown on drawing below push it through the pre cut cable housing and fix it at the assembly unit on top of the right side of the fork crown For
19. od starts at the day of purchase This warranty is limited to the first buyer what means the first person who uses the bike and only with the use it was made for Furthermore this warranty is limited to purchases via authorized SCOT T dealers The warranty is solely granted in case of purchase of a completely assembled bike to the explicit exclusion of purchases of not completely assembled bikes In case of a warranty claim the decision to repair or to replace the defective part is up to SCOTT Non defective parts will only be replaced at the guarantee s own expense Fair wear and tear is not covered by the warranty A complete list of all parts of wear and tear can be found in the next chapter of this manual In addition you will find at the end of this manual a protocol for the handing over of the bike which will remain in copy at the SCOTT dealer after acceptance and signature of the consumer It is obligatory to show this protocol of handing over together with the defective part in case of a warranty claim given that it provides evidence of purchase Otherwise no warranty is granted In principle this warranty is granted worldwide Claims must be made through an authorized dealer for information regarding the nearest dealer write or call this company or the national SCOTT distributor Normal wear accident neglect abuse improper assembly improper maintenance by other than an authorized dealer or use of parts or devices not
20. very similar to the above mentioned assembly and setup of the FOX Nude Please follow the details shown in the FOX manuals attached to this bike RECOMMENDED TOOLS FOR THE SHOCK SET UP When setting up the shock we recommend using a shock pump with a scale up to 20 bars 300 psi with a special air valve connector This prevents air from escaping when removing the pump from the shock valve to achieve a more accurate air pressure Please note that air will flow into the hose and indicator when counter checking the air pressure so you have to set up the recommended pressure again after this action Make sure to balance at least this air loss when you make a check of the air pressure of the shock Please also note that the indicators of shock pumps have a tolerance of max 10 18 Gsco7TrTr BIKE OWNER S MANUAL SET UP SPARK WITH FOX NUDE SHOCK The Set Up of the FOX Nude Shock can be easy done within a few minutes IMPORTANT Important For all adjustments of the air spring the remote lever has to be in position Descent mode To adjust the air pressure of the air chamber of the FOX Nude Shock please refer to the following instruction 1 remove the valve cap of the valve S5 located on the shock housing S3 2 mount the shock pump with its adaptor on the valve 3 please take into account that it takes some air pressure from inside the shock to drive the indicator on the pump Make sure to balance at least this air loss wh
21. wn below Please only use the matching adjustment shims as their shape is designed specifically to fit with the countersunk bolts SET UP OF OTHER SHOCK MODELS SCOTT strongly recommends using only the FOX Nude FOX Float CTD X Fusion E1 Shock with the Spark bike as we designed both parts to be perfectly matched with a linear suspension rate Also on those shock models the SAG should be 10mm For all basic steps on inflating the shock and adjusting the rebound please refer to the description of the FOX Nude set up OTHER SHOCK MODELS ON SPARK If you use a different rear shock model other than the original one on the bike please ensure the shock will not hit the frame at any position as this will damage the frame Please follow the instructions below Ensure that the rear shock or its accessory parts do not touch the frame when mounting or suspending To check the shock release the air remove the coil install the shock and compress the shock completely If the shock touches the frame while doing the above actions do not use this shock as it will cause damage to the frame swingarm or shock ENGLISH SPARK HEADSET OPTIONS Spark features different versions of headset systems 1 A tapered headset and fork steerer system to match with semi integrated headsets of the 50 61 mm range with ID of Headtube of 44 0mm on top and 54 9mm on the lower end Headset Pro Zero Logic Press Fit Taper 18mm
Download Pdf Manuals
Related Search