Home
User`s Manual & Operating Instructions
Contents
1. User s Manual amp Operating Instructions Model Numbers HH 70 SS A CONSUMER READ AND SAVE THESE INSTRUCTIONS IT GENERAL HAZARD WARNING READ AND UNDERSTAND ALL OF THE INSTRUCTIONS IN THIS MANUAL BEFORE ASSEMBLING STARTING OR SERVICING THE HEATER Be sure to comply with the instructions and warnings provided with this heater Failure to comply can result in fire or explosion that can cause property loss bodily injury or loss of life Only persons who can follow and understand these instructions should operate or service this heater If you need heater info such as an operating manual labels etcetera contact Pinnacle Products International at 800 641 6996 FEN NOT FOR USE IN RESIDENTIAL LIVING AREAS OR IN ENCLOSED SPACES WITHOUT ADEQUATE VENTILATION TO BE USED IN WELL VENTILATED COMMERCIAL INDUSTRIAL OCCUPANCIES This is an unvented portable heater that uses air Oxygen from within the area in which it is used Failure to provide adequate combustion and ventilation air will result in asphyxiation carbon monoxide poisoning bodily injury or death Refer to Ventilation on Page 5 2013 Pinnacle Products International Inc 668 Stony Hill Road 302 Yardley PA 19067 USA Fax 215 891 8461 Web www remingtonheater com Email info pinnacleint com gt PINNACLE 751000230 13 NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR REMINGTON WHILE CONNECTED TO A POWER SOURCE Table Of Contents
2. Refer to Ventilation on page 7 for further instructions 2013 Pinnacle Products International Inc AWARNING RISK OF ELECTRIC SHOCK ALWAYS use only the electrical power voltage and freguency specified on the model plate of the heater ALWAYS use only three prong grounded outlet and extension cord ALWAYS use only 14 AWG or better extension cord ALWAYS unplug the heater when not in use ALWAYS install the heater so that it is not directly exposed to water spray rain dripping water or wind RISK OF BURNS FIRE AND AWARNING EXPLOSION NEVER use fuels such as gasoline benzine paint thinners or other oil compounds in this heater NEVER refill the heater s fuel tank while the heater is operating or still hot This heater is EXTREMELY HOT while in operation NEVER block air outlet front NEVER use duct work in front of heater NEVER move or handle heater while still hot NEVER transport heater with fuel in tank NEVER use with an external fuel tank A WARNING CAUTION HOT WHILE IN G OPERATION DO NOT TOUCH KEEP CHILDREN ANIMALS CLOTHING AND COMBUSTIBLES AWAY FROM HEATER Keep all combustible materials away from this heater Minimum Clearance From Combustibles sa des 4 amp mw ec ALWAYS locate heater on a stable and level surface If your heater is equipped with a thermostat once it is plugged in
3. Safety Info Ple toD asso 1 2 Troubleshooting Guid e 9 Features and Specifications 3 Wiring YL Lg NN YN eI IR 10 HH 70 SS A Assembly 4 Exploded VIGW i sde 11 VEN PR O Be Pans NG oe cies seers RW 12 SAMO NN A AEN m 14 ME Aa 7 8 Safety Information AWARNING FIRE BURN INHALATION AND EXPLOSION HAZARD Keep combustibles such as building materials paper or cardboard a safe distance away from the heater as recommended by these instructions Never use the heater in spaces which contain products such as gasoline solvents paint thinners dust particles volatile or airborne combustibles or any unknown chemicals This is an unvented portable heater It uses air Oxygen from the area in which it is used Adequate combustion and ventilation air must be provided Refer to Ventilation on page 5 Bulk fuel storage should be a minimum of 25 feet from heater AWARNING DO NOT OPERATE THIS HEATER UNTIL YOU HAVE READ AND THOROUGHLY UNDERSTAND THESE SAFETY AND OPERATING INSTRUCTIONS Failure to comply with the precautions and instructions provided with this heater can result in death serious bodily injury property loss or damage from the hazards of fire soot production explosions burns asphyxiation or carbon monoxide poisoning Only persons who can read and understand these instructions should use or service
4. Clean replace Nozzle Clean replace Photocell Adjust Photocell position Replace Photocell Check wiring connections See Wiring Diagrams Page 10 Check to be sure cooling fan is not obstructed Fill tank with fresh Kerosene diesel 2 Clean replace Spark Plug Clean replace Fuel Filter Clean replace Nozzle Rinse out fuel tank with clean fresh Kerosene diesel Inspect all electrical connections See Wiring Diagrams Page 10 Re attach Transformer wires to Spark Plug Replace Transformer Inspect all electrical connections on Wiring Diagrams Page 10 Use a new extension cord or try another electrical socket Sound will stop after 3 seconds If grinding sound continues add fuel to tank Push Operating Switch to OFF and allow heater to cool for 5 minutes Push Operating Switch back to ON Check power cord and extension cord to insure of proper connection Test power supply Check replace Fuse Inspect all electrical connections See Wiring Diagrams Page 10 Be sure pump pressure is adjusted correctly Be sure Kerosene diesel is not old or contaminated Oil Fired Radiant Heater User s Manual NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR mm REMINGTON WHILE CONNECTED TO A POWER SOURCE Wiring Diagram HH 70 SS A PANEL WHITE PCB OPERATION LAMP 9 1 OPERATING ERROR CHECK LAMP SWITCH CONTROL PCB
5. SUN STREAM THERMOSTAT PHOTO CELL POWER PLUG AC 120V 60Hz ELECTRIC OUTLET Figure 12 2013 Pinnacle Products International Inc 10 Oil Fired Radiant Heater User s Manual NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR REMINGTON WHILE CONNECTED TO A POWER SOURCE Exploded View HH 70 SS A 2013 Pinnacle Products International Inc 11 Oil Fired Radiant Heater User s Manual A EVER LEAVE HEATER UNATTENDED WHILE BURNING OR REMINGTON WHILE CONNECTED TO A POWER SOURCE Parts List Hem 3 3 Description HH 70 SS A O Main PCB Assembly 75 025 0400 Shell 75 01 1000 CAE 75 01 0060 Nozze 75 06 0400 Nipple 75040 0610 Tip Over Sensor 75 051 0200 Temperature Limit Switch 75 040 0100 2013 Pinnacle Products International Inc 12 Oil Fired Radiant Heater User s Manual NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR mm REMINGTON WHILE CONNECTED TO A POWER SOURCE 2013 Pinnacle Products International Inc 13 Oil Fired Radiant Heater User s Manual psp NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR WHILE CONNECTED TO A POWER SOURCE REMINGTON LIMITED WARRANTY Pinnacle Products International Inc warrants this heater to the original retail purchaser only to be free from defects in material and workmanship for a period of one 1 year from the date of initial purchase This product must be properly installed main
6. heaters Kerosene Diesel forced air heaters are primarily intended for use for temporary heating of buildings under construction alteration or repair Direct fired means that all of the combustion products of the heater enter the heated space This appliance is rated at 9896 combustion efficiency but does produce small amounts of carbon monoxide CARBON MONOXIDE POISONING AWARNING MAY LEAD TO DEATH Carbon monoxide is toxic Humans can tolerate only small amounts of carbon monoxide and so precautions should be taken to provide proper ventilation Failure to provide proper ventilation in accordance with the instructions in this manual can result in death People with breathing problems should consult a physician before using this heater Early signs of carbon monoxide poisoning resemble the flu Symptoms of improper ventilation carbon monoxide poisoning are Headache Dizziness Nausea Dry Mouth Sore Throat Burning of Nose and Eyes If you experience any of these symptoms GET FRESH AIR AT ONCE Have your heater serviced and check for proper ventilation Some people are more affected by carbon monoxide than others These include pregnant women those with heart or lung problems anemia or those under the influence of alcohol or at high altitudes Use this heater in only well ventilated areas Provide at least a three sguare foot 2 800 sg cm opening of outside air for every 100 000 Btu Hr heater rating
7. it can start at anytime in accordance with the thermostat setting Oil Fired Radiant Heater User s Manual NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR REMINGTON WHILE CONNECTED TO A POWER SOURCE Specifications Heating Area m 1 750 Specifications subject to change without notice Features HH 70 SS A SHELL RING SHELL HANDLE OPERATING SWITCH CORD COVER li POWER CORD ASS Y COOLING BOX FUEL TANK ASS Y FUEL GUAGE ASS Y Figure 1 FUEL CAP 2013 Pinnacle Products International Inc 3 Oil Fired Radiant Heater User s Manual NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR REMINGTON WHILE CONNECTED TO A POWER SOURCE Assembly Instructions HH 70 SS A Remove the heater and all packaging materials Note Save the box and packaging materials from the shipping carton for future storage What s In The Box IN Carry Handle 1 Black Screws 2 Carry Handle Assembly Tools Needed 1 Align holes in the upper housing with the 2 Phillips Head Screw Driver holes in the handle as shown in Figure 2 2 Insert screws and tighten firmly Attach the handle while still in the box for easier unpacking See Figure 3 2013 Pinnacle Products International Inc 4 Oil Fired Radiant Heater User s Manual NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR REMINGTON WHILE CONNECTED TO A POWER SOURCE Operation Fueling The Heater Ventilation Kerosene o Ri
8. EATER UNATTENDED WHILE BURNING OR REMINGTON WHILE CONNECTED TO A POWER SOURCE Troubleshooting Guide Possible Cause Heater fires but shuts down after a short period of time Heater will not operate or motor runs for short time Fan does not operate when heater is plugged in and Operating Switch is in the ON position Heater makes grinding noise Heater does not turn on and the lamp is not lit Poor combustion and or soot production 2013 Pinnacle Products International Inc 9 Dirty Fuel Filter Nozzle Dirty Photocell Dirty Photocell not installed properly Photocell Defective Improper electrical connec tion between Circuit Board and Photocell Cooling Fan is obstructed No Kerosene diesel in fuel tank 2 Corroded Spark Plug or incorrect plug gap Dirty Fuel Filter Dirty Nozzle Moisture in Fuel Fuel Tank Improper electrical connection between Transformer and Circuit Board Transformer Wires not connected to Spark Plug Defective Transformer Broken electrical connection between Circuit Board and motor Not enough amps available to power heater Air in fuel pump Temperature limit sensor has over heated No electrical power Fuse break down Improper electrical connection between Temperature Limit Sensor and Circuit Board Pump Pressure Poor fuel quality Clean replace Fuel Filter
9. NEVER store Kerosene in the living space Kerosene should be stored in a well ventilated area outside the living area NEVER store Kerosene in direct sunlight or near a source of heat NEVER use Kerosene that has been stored from one season to the next Kerosene deteriorates over time OLD Kerosene WILL NOT BURN PROPERLY IN THIS HEATER NOTE Kerosene should only be stored in a blue container that is clearly marked Kerosene Never store Kerosene in a red container Red is associated with gasoline 2013 Pinnacle Products International Inc 5 Oil Fired Radiant Heater User s Manual REMINGTON NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR WHILE CONNECTED TO A POWER SOURCE Operation Starting the Heater Ignition HH 70 SS A 1 Fill the tank with Kerosene or other approved fuel until needle on fuel gauge points to F 2 Replace fuel cap and tighten firmly 3 Connect the heater to a three prong grounded power source You must use a three prong grounded extension cord that is at least 1 8 meters long and is a minimum of 14 AWG rating NOTE On first ignition or after refueling you may hear a grinding sound just before ignition This is the fuel pump removing the air from the fuel line Your heater will start up within seconds If it does not start repeat start up procedures with fuel gauge reading at least 1 2 tank NOTE The electrical components of these heaters
10. are protected by a fuse mounted in the PC board If the heater fails to ignite check this fuse first and replace if necessary Also check the power source to be sure the proper voltage is being provided to the heater 1 Complete steps 1 3 above 2 Push the power switch to the ON position The power indicator lamp will light and heater will ignite See Figure 5 Power Switch 2013 Pinnacle Products International Inc Stoping the Heater Cool Down 1 Turn the power switch to the OFF position Combustion will stop and the Cooling Cycle will begin HH 70 SS A approx 3 mins When the Cooling Cycle is complete the fan will stop running and it will be safe to unplug the heater NOTE Unplugging the heater before the Cooling Cycle has been completed may cause overheating possible damage to the heater and heat plate Restarting the Heater 1 Wait ten seconds after Cooling Cycle has been completed 2 Follow all start up procedures above DO NOT disconnect heater AWARNING from power source before cooling cycle has been completed Electrical Outlet Never plug an appliance with more than a 5 amp rating into this outlet See Figure 6 Always keep outlet covered when not in use Electrical Outlet Oil Fired Radiant Heater User s Manual NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR REMINGTON WHILE CONNECTED TO A POWER SOURCE Maintenance Long Term Storag
11. ation or liability in connection with the sale installation use removal return or replacement of its equipment and no such representations are binding on Pinnacle Products International Inc Always be sure to specify the model number and serial number when making any claim with Pinnacle Products International Inc For your convenience use the space provided below to list this information Register Your Product Online at http www remingtonheater com Product_Registration php Locating Your Serial Number Your serial number can be found on a blue label on the left side cover It will begin with 2 digits the letter H followed by 6 digits For Example 13H123456 Have your Serial Number ready before calling customer service at 800 641 6996 Model Serial Date of Purchase 2013 Pinnacle Products International Inc 14 Serial Number Label A AT Oil Fired Radiant Heater User s Manual tn PINNACLE 2013 Pinnacle Products International Inc 668 Stony Hill Road 302 Yardley PA 19067 USA Toll Free 800 641 6996 Fax 215 891 8461 Web www pinnacleint com Email info pinnacleint com
12. e SPARK PLUG Clean and re gap every 600 hours of operation or replace as needed After removing the Spark Plug clean the terminals with a wire brush Re gap the terminals to 0 140 3 5mm See Figure 7 1 Unscrew the fuel cap 2 Using an approved siphon remove the Kerosene or diesel 3 Using a small amount of Kerosene or diesel rinse and swirl the fuel inside the fuel tank NOTE NEVER MIX WATER WITH FUEL It will SPARK PLUG cause rust inside the tank 4 Empty the tank completely IMPORTANT Never store leftover Kerosene between seasons using old fuel can damage heater Store Heater in a dry well ventilated area Be sure that the storage area is free of dust and corrosive vapors Repack the heater BURNER BODY in the original packaging and keep user s manual in an easily accessible place FAN BLADES The fan blades should be cleaned at least once Service per heating season depending on conditions TP Remove all accumulated dust and dirt with a AWARNING Addio bas ord ul burst of condensed air See Figure 8 DO NOT TAMPER WITH THE UNIT HAVE AN ESO cul NECESSARY ADJUSTMENT OR REPAIRS We suggest following a maintenance schedule as EXPERIENCED SERVICEMAN MAKE ANY Z follows an a ii y BLOWER MOTOR ASS Y FUEL FUEL TANK TIP Follow the long term storage instructions to flush the tank Flush tank every 200 hours of operation or as needed DO NOT flush with wat
13. er use fresh Kerosene only O 2013 Pinnacle Products International Inc 7 Oil Fired Radiant Heater User s Manual NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR REMINGTON WHILE CONNECTED TO A POWER SOURCE Maintenance Service Continued NOZZLES FILTERS Nozzles should be cleaned or replaced at least The fuel filter and oil filter should be cleaned at once per heating season Contaminated fuel least twice per heating season by rinsing it in could make this necessary immediately To clean clean Kerosene or diesel Contaminated or old dirt from nozzle blow compressed air through fuel could make cleaning necessary immediately nozzle front It may be necessary to soak nozzle See Figure 11 in clean Kerosene or diesel to help loosen any particles See Figure 9 DIFFUSION N FUEL LINE BLOWER MOTOR ASS Y BURNER BODY BURNER BLADE BURNER INSULATOR NOZZLE INTAKE HOSE FUEL INTAKE PACKING ELECTRONIC PUMP 31 INTAKE PIPE OIL FILTER ASS Y Figure 9 PHOTOCELL The photocell should be cleaned at least once per heating season or more depending on conditions Use a cotton swab and water or alcohol to clean the lens of the photocell Be certain to reinstall the photocell in proper position as shown below See Figure 10 2013 Pinnacle Products International Inc 8 Oil Fired Radiant Heater User s Manual NEVER LEAVE H
14. sk of indoor air pollution and Carbon For optimal performance of this heater it is Monoxide Poisoning Use heater only in well strongly suggested that Kerosene be used ventilated areas Kerosene has been refined to virtually eliminate contaminants such as sulfur which can cause a rotten egg odor during the operation of the Refer to Safety Information on pages 1 2 for information about Carbon Monoxide Poisoning heater Using diesel fuel can cause excess soot ALWAYS provide a fresh air opening in the heated production Do not use Bio Diesel as this fuel will space of at least 2 800 square centimeters damage your heater s seals and filter 3 sq ft for each 100 00 Btu Hr of heater output Provide a larger opening if more heaters are being NEVER REFUEL THIS HEATER used LANCE WHILE IT IS HOT OR CARBON MONOXIDE POISONING Er FIRE OR EXPLOSION COULD ADANGER MAY LEAD TO DEATH ACAUTION NEVER FILL THE FUEL TANK As an example a HH 70 SS A will require INDOORS ALWAYS FILL i THE TANK OUTDOORS BE SURE THAT OT PI THE HEATER IS ON LEVEL GROUND WHEN A single car garage open 9 inches or FUELING AND NEVER OVERFILL THE TANK Two 2 32 inch windows open 15 inches WARNING DO NOT USE GASOLINE OR CRANKCASE DRAININGS NEVER use fuel such as benzene alcohol white glass camp stove fuel paint thinners or other oil compounds in this heater THESE ARE VOLATILE 5 FUELS THAT CAN CAUSE A FIRE OR EXPLOSION
15. tained and operated in accordance with the instructions provided Pinnacle Products International Inc requires reasonable proof of your date of purchase from an authorized retailer or distributor Therefore you should keep your sales slip invoice or cancelled check from the original purchase This Limited Warranty shall be limited to the repair or replacement of parts which prove defective under normal use and service within the warranty period and which Pinnacle Products International Inc shall determine at its reasonable discretion This warranty does not apply to products purchased for rental use This Limited Warranty does not cover any failures or operating difficulties due to normal wear and tear accident abuse misuse alteration misapplication improper installation or improper maintenance and service by you or any third part Failure to perform normal and routine maintenance on the heater shipping damage damage related to insects birds or animals of any kind and damage due to weather conditions are also not covered In addition the Limited Warranty does not cover damage to the finish such as scratches dents discoloration rust or other weather damage after purchase All transportation costs for the return of damaged product or parts will be the responsibility of the purchaser Upon receipt of damaged item Pinnacle Products International Inc will examine the item and determine if defective Pinnacle Prod
16. this heater WARNING DO NOT START THE HEATER WHEN EXCESS OIL HAS ACCUMULATED WARNING DO NOT START THE HEATER WHEN THE CHAMBER IS HOT AWARNING CALIFORNIA RESIDENTS This product contains chemicals including lead known to the State of California to cause birth defects or other reproductive harm Wash hands after handling MASSACHUSETTS RESIDENTS Massachusetts state law prohibits the use of this heater in any building which is used in whole or in part for human habitation Use of this heating device in Massachusetts requires local fire department permit M G L C 148 Section 10A NEW YORK CITY RESIDENTS The New York City Fire Code prohibits the storage handling and use of kerosene fueled heaters for space heating Any person violating that provision may be punished by a fine up to 10 000 and a term of imprisonment of up to 6 months THE INSTALLATION OF THIS HEATER SHALL COMPLY WITH THE REGULATIONS OF THE AUTHORITIES HAVING JURISDICTION a Look for this icon throughout the manual for helpful tips on how to assemble use and clean your OFR Heater 2013 Pinnacle Products International Inc 1 Oil Fired Radiant Heater User s Manual REMINGTON NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR WHILE CONNECTED TO A POWER SOURCE Safety Information RISK OF INDOOR AIR AWARNING POLLUTION The products described in this manual are Kerosene Diesel direct fired forced air
17. ucts International Inc will repair or replace and return the item freight pre paid If Pinnacle Products International Inc finds the item to be in normal operating condition or not defective the item will be returned freight collect This Limited Warranty is in lieu of all other express warranties Pinnacle Products International Inc disclaims al warranties for products that are purchased from sellers other than authorized dealers or distributors AFTER THE PERIOD OF THE ONE 1 YEAR EXPRESS WARRANTY EXPIRES Pinnacle Products International Inc DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR APPLICATION FURTHER Pinnacle Products International Inc SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY THIRD PARTY FRO ANY SPECIAL INDIRECT PUNITIVE INCIDENTAL OR CONSEQUENTIAL DAMAGES Pinnacle Products International Inc assumes no responsibility for any defects caused by third parties This Limited Warranty gives the purchaser specific legal rights a purchaser may have other rights depending upon where he or she lives Some states do not allow the exclusion or limitation of special incidental or consequential damages or limitations on how long a warranty lasts so the above exclusion and limitations may not apply to you Pinnacle Products International Inc does not authorize any person or company to assume for it any other oblig
Download Pdf Manuals
Related Search
Related Contents
Genie QuickStock Brochure Mio Spirit 470 Painless Performance LS1 User's Manual [364-582 XZF-65780R U モコ ン 】 User Manual - Hedland Flow Meters 取扱説明書 - 日立の家電品 ESP-LXD-Steuergerät 545167699 Rev. 1 7/31/08 BRW Hama 00106671 mobile headset FD-660 E Manual Rev0101 Copyright © All rights reserved.
Failed to retrieve file