KD-HDMSW4X4 - Key Digital
Contents
1. HR 75 ft KD CATHD4X4Rx Quick Setup Guide Connections 1 Begin with the KD HDMSW4x4 and all input output devices turned off and power cables removed 2 Connect HDMI sources to the appropriate input ports on the KD HDMSW4x4 3 Connect either or both HDMI and CAT5e 6 outputs You will require 2x CAT5e 6 UTP or STP cables for each Balun connected 4 Connect power to the KD HDMSW4x4 as well as to all other input and output devices and turn them on 5 Operate the KD HDMSW4x4 switcher via front panel buttons IR Remote Serial IR or RS 232 control Operation After performing the setup above the unit is ready for operation There are several options for controlling the unit Commands can be issued via IR remote control RS 232 or by using the front panel buttons Note that the advanced commands are available only via the RS 232 protocol Settings The KD HDMSWA4x4 features a library of 9 internal EDID files in addition to allowing the Input source to receive a copy of the EDID information of any selected Output connected via HDMI or CAT5e 6 The default EDID setting is 01 10801 w PCM 2ch Digital Audio Changing to different EDID settings may be necessary when connecting to or from an AV Receiver or for passing 3D content derived from a Cable or Satellite source if the default EDID has problems They can also speed up the switching process with cable or satellite sources Available EDID library2. gt Full switching of 2 independent matrixes HDMI DVI Audio Video one directional IR or RS 232 Tx to Rx gt Supports all SD HD and VESA VGA SVGA XGA WXGA SXGA UXGA resolutions up to 1080p 60Hz amp 50Hz SD amp HD 480i 480p 720p 1080i 1080p VESA VGA RGBHV From 640x480p up to 1920x1200 gt Supports lossless compressed digital audio Dolby TrueHD Dolby Digital Plus and DTS HD Master Audio gt Internal EDID Library features 9 default EDID configurations in addition to Native EDID data for any Output Display gt Supported HDMI 14 Features 3D Ready 4K Resolution Support 2010 Key Digital Inc All rights reserved red L c C fe Page 4 Connections Buttons and LEDs Rear Panel Connections All connections to the KD HDMSW4X4 are found on the rear panel of the unit Refer to the illustrations below for port assignments while making connections HDMI Inputs Expansion 7 SerilIR Ports Operation Mode Switch RS 232 Port CATSe 6 HDMI HDMI CAT5e 6 Outputs HDMI CAT5e 6 IR Eye Serial IR Connections gt HDMI Inputs The 4 HDMI Inputs are located in the center of the back panel The Inputs have a blue LED which will light when a source is connected and synced gt HDMI and CAT5e 6 Outputs There are 4 sets of HDMI Outputs and their associated CAT5e 6 Outputs lo
3. and HDCP techologies EDID Control Each input EDID is either a choice of any of the active zone displays connected via HDMI DVI or CAT5e 6 to the outputs or form internal library of 9 default EDID s DDC Signal Data Inout DDC Signal 5 Volts p p TTL HDMI Video Audio Signal Input Video Signal 1 2 Volts p p DDC Communication EDID and HDCP Bi directional Transparency from Display to Source Wired IR modulated IR signal input O 5V TTL or 10to 10V Power External Power Supply 12V 2A General Regulation CE RoHS WEEE Rack Mount 1U Full Rack Width rack ears included Enclosure Black Metal KD HDMSW4x4 Product Dimensions 17125 W x 5 50 D x 1 75 H KD CATHD4x4Rx Product Dimensions 3 25 W x 1 875 D x 875 H KD HDMSW4x4 Product Weight 4 05 Ib KD CATHD4x4Rx Product Weight 25 Ib Shipping Weight 10 Ib Mey cigiFal How to Contact Key Digital Fin A mportant Product Important Product Warnings System Design Group SDG For system design questions please contact us at gt Phone 914 667 9700 3 If installing the unit into wall or mounting bracket into sheet rock provide proper screw support gt E mail sdg keydigitalcom with bolts or sheet rock anchors Technical Support i For technical questions about using Key Digital products please contact us at Safety Instructions EEE EN Please be sure to follow these instructions for safe operation of your unit a Da gt E mail tech keydig
4. settings 01 is the default 01 1080i w PCM 2ch Digital Audio 06 3D w Dolby Audio 02 1080i w HD Audio 07 3D w HD Audio 03 1080p w PCM 2ch Digital Audio 08 DVI VESA 1280x1024 04 1080p w HD Audio 09 DVI VESA 1920x1200 05 3D w PCM 2ch Digital Audio When selecting an EDID from the library Settings 01 09 your source device will see the KD HDMSW 4x4 EDID choice instead of the displays EDID over riding the displays own EDID information If your display is not capable of accepting the video resolution or audio type selected you may not see a picture or sound In this case please choose another more compatible EDID or use the default EDID EDID settings can only be changed through the RS 232 command protocol See the RS 232 command section below for a list of EDID commands available Mey CigiFal KESE m m Remote Control You may control the KD HDMSW4x4 switching commands by using Ay B the supplied IR Remote control There are 4 groups of controls one m f group for each Output Each Input can be selected by pressing the A Input numbers 1 4 5 re Inputs 1 2 3 4 Output 3 p _ 1 2 3 4 Front and Rear panel sensors are available for use with the IR Output 4 extender A wired IR serial connector is also provided at the rear of OS the unit D ED 5 Wired IR Extender KD IRB3099 Unit included in the KD IRKIT300 uses a 3 omm Mgestaggale Mono cable Wired IR Extender Back of the Unit 3 5mm male to m
5. Baluns If you will be utilizing the KD CATHD4x4Rx Baluns included please follow this procedure gt 2 CAT5e 6 UTP or STP cables need to be used gt Be careful to connect the Video Audio jacks to each other and the Data jacks to each other Do not cross these connections gt Use the shortest length HDMI cable you can when connecting the Balun to the Display gt Ensure that the 2 cables are run directly from the switcher to the Baluns Ww Do not use patch panels punch downs or wall plates Ww Each Balun is supplied with a power supply gt Key Digital recommends the use of CAT5e 6 STP cable with shielded RJ45 connectors for optimum performance and distances from your Balun Mey dogs Page 6 Transmitting IR signals with KD CATHD4X4Rx Baaluns The IR signal going to the Balun must be from a 12v powered output such as that from a common distribution block The Balun does not provide power for this signal In the case of an IR receiver connect the 3 or 4 wire receiver to the distribution block and the emitter output of the block into the Balun When connecting the IR Emitter to the device you wish to control make sure to find the IR receiver area on your particular device first Experiment with locations and test the functionality before permanently fixing it Application Example Blu Ray RS232 Control Control System 91V5 lend CAT5e 6 gt HDMI DVI
6. O Dun y m U A PHANTOM S E R I E S KD HDMSW4X4 HDMI DVI Matrix Switcher capable of switching up to 4 HDMI DVI Video Sources Inputs to 4 independent Zones Outputs via HDMI DVI and CAT5e 6 with included 4 KD CATHD4X4Rx Baluns set Up Guide Li Li a Aotdoooo a GE i mm mn f j HIGH DEFINITION MULTIMEDIA INTERFACE Key Digitals Phantom Series KD HDMSW4x4 is a HDMI DVI Matrix Switcher capable of switching up to 4 HDMI DVI Sources Inputs to 4 independent Zones Outputs via HDMI DVI and 2 CAT5e 6 IR routing over CAT5e 6 is also available Kit includes 4 KD CATHD4x4Rx Receiver Baluns with power supplies four 3 and four 6 HDMI cables el digital MeL Higie The Experts in Digital Video Technology and Solutions CE RoHSS WEEE COMPLIANT COMPLIANT ue Table of Contents Key Benefits About KD HDMSW4X4 2 gt Transmits 1080p 60HZz up to 75 ft 1080i and all lesser resolutions up to 100 ft when used with i included KD CATHD4X4Rx receiver Baluns Connections Buttons and LEDs 4 BENE gt Video Audio IR and RS 232 distribution via two CAT5e 6 cables alu eee lle gt 2 active outputs per zone provide 8 total outputs 4 HDMI DVI and 4 CAT5e 6 in a 4X4 Application Example 6 configuration enabling flexible integration options Quick Setup Guide 7 gt IR signals may be routed from your control system through the switch to your display location Settings 7 over CAT5e 6 for full control of your d
7. ale mono cable KD IRCB204 Connecting Block RS 232 Commands IR Extender You may want to use an IR extender such as the KD IRKIT300 The KD HDMSWA4X4 provides access to all functions when used with an RS 232 control system Key Digital provides a resource database for downloadable control modules at www keydiigital com controlmain aspx Connection protocol is as follows Baud rate 57 600 Data Bits 8 RS 232 cable pin out Parity None Stop Bits 1 Br Ground Flow Control None Carriage Return Required Line Feed Required Pin 3 Receive Pin 2 Transmit For a complete list of all available RS 232 commands please see the Downloads section on the KD HDMSWAX4 product page at www keydigital com NOTE All commands are case insensitive Spaces are shown for clarity all commands should not have any spaces Every command below requires a carriage retum at the end of the string for the command to be executed If a new line character is received a prompt should be sent back Values for Commands gt H Help Help command List of all RS 232 commands and Firmware version gt STA Status Command Displays unit status for all internal variables such as Video Input IR Input selected for each Output and EDID selected for each Input gt PF Power Off Power Off command System Commands Video Switch SP O xx SI yy To switch the desired Video Input to the desire
8. ault EDID Library selection see list below Where yy Output numbers 01 04 when H or C variables are selected OR Default EDID library settings 01 08 when D variable is selected This command will either copy the EDID information from a selected Output to a specific Input or All Inputs or write EDID information from an internal library of default EDID settings to a specific Input or All Inputs Mey cCigiFal Example To copy the EDID information from HDMI Output 2 to Input 4 issue the command SPCEDID04H02 Example To copy the EDID information from CAT5 Output 2 to All Inputs issue the command SPCEDIDACO2 Example To write the EDID information from the built in default EDID library using default EDID 1 to Input 2 issue the command SPCEDIDO2DO1 Below are listed the Default EDID Library selections 01 09 01 1080i w PCM 2ch Digital Audio 02 1080i w HD Audio 03 1080p w PCM 2ch Digital Audio 04 1080p w HD Audio 05 3D w PCM 2ch Digital Audio 06 3D w Dolby Audio 07 3D w HD Audio 08 DVIVESA 1280x1024 09 DVI VESA 1920x1200 Front Panel Buttons Enabled Disabled SP C FB E D Where E will Enable the front panel buttons and D will Disable the front panel buttons Example To Disable the front panel buttons issue the command SPCFBD Reset to Factory Defaults SP C DF xx Where xx 01 08 and is the default EDID
9. cated on either side of the HDMI Inputs Both HDMI and CAT5e 6 Outputs have a blue LED which will light when a display Balun is connected and synced gt The HDMI and CAT5e 6 Outputs are both active simultaneously gt There are 4 Serial IR Inputs located on the right side of the back panel These are standard 3 5mm mono jacks Connect these to any control system for routing IR over the CAT5e 6 outputs Power Connection Page 5 gt The RS 232 Serial IR Optical IR Sensor Operation Mode Switch and Power connections are located on the right side of the back panel The Operation Mode switch is used to update the unit s firmware which is done using the DB9 RS 232 port The firmware version as well as all RS 232 commands is available through the RS 232 command H A detailed list of RS 232 commands is available later in this guide gt If newer firmware is made available complete updating instructions will be included with it Check the Key Digital website for any firmware updates Front Panel Buttons and LED s Output Select Buttons IR Eye Input LEDs gt There are 4 Output buttons along the front panel gt Each press of an Output button cycles through each of the 4 Inputs gt A blue LED will indicate which Input has been selected for each Output button gt There is also an Optical IR window located on the right side of the front panel for the remote control signals KD CATHD4x4Rx
10. d Output Where xx the Output number 01 04 OR A for All Where yy the Input number 01 04 OR U D for Up Down respectively U D will increase decrease the input number from its current position This command will switch Inputs to your desired Output Example To switch Input 3 to Output 1 issue the command SPO01 S103 Example To incrementally switch the Inout Up from its present number for Output 1 issue the command SPO01 SIU Example To switch All Outputs to Input 3 issue the command SPOASIO3 IR Routing SP O xx SR yy To rout Serial IR signals Where xx Output numbers 01 04 OR A for All Outputs Where yy Serial IR Input numbers 01 04 or U D for Up Down respectively U D will increase or decrease the IR input number from its current position This command will rout the selected Serial IR Inout number 1 4 to the desired Output number over the CAT5e 6 connection Example SPOASRO2 Will carry IR from IR Input port 2 to Al Outputs SPO02SR01 Will carry IR from IR Input port 1 to Output 2 EDID Copy and Default EDID Library SP C EDID xx H C D yy To Copy EDID to Input from Output via HDMI or CAT5e 6 or from a Default Library Where xx Input numbers 01 04 OR A for All Inputs Where H EDID Copy from HDMI Output Where C EDID Copy from CAT5e 6 Output Where D Def
11. isplay or other remotely located devices gt Serial IR Optical IR Front Panel amp RS 232 control Remote Control 8 i i gt Supports major control systems such as AMX Control4 Crestron RTI Universal RS 232 Commands 8 i eg Accessories Specifications 10 Important Product Warnings amp Safety Instructions 12 H ee Rens SE een RENE Sra Cara ae a 4 5V1A DC Power Supplies for KD CATHD4x4Rx Baluns REED SAR m Apr Brackets for KD CATHD4x4Rx Warranty Information 13 1 External 12 Volt 2 Amp power supply 110V 240V 50 60H7z 1 IR Remote control 1pr Rack mounting ears for KD HDMSW4x4 4 IR Emitters for use with Baluns About KD HDMSW4X4 4 3 ft HDMI Cables Visit www keydigital com for HDMI cable specifications 4 6 ft HDMI Cables Visit www keydigital com for HDMI cable specifications Description Mounting gt KD HDMSW4x4 is an HDMI Matrix switcher capable of switching 4 independent Inputs Sources to 4 independent Outputs Zones There are both HDMI and CAT5e 6 Outputs over 2 CAT5e 6 cables and are available simultaneously Built in fully matrixed Serial IR routing is also available to control your displays remotely gt Rack mount Secure the rack ears to each side of the KD HDMSW4X4 with the supplied hardware Then fasten the unit to the rack rails with the included machine screws Key Features gt Simultaneous availability of HDMI DVI and CAT5e 6 outputs
12. ital com Connect all cables before providing power to the unit 2 Test for proper operation before securing unit behind walls or in hard to access spaces 1 Read and follow all instructions i Repairs and Warranty Service 2 Heed all warnings 3 Dane ende Should your product require warranty service or repair please obtain a Key Digital Return Material amp Authorization RMA number by contacting us at 4 Clean only with dry cloth x i gt Phone 914 667 9700 5 Install in accordance with the manufacturer s instructions u gt E mail rma keydigital com 6 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Feedback 7 Only use attachments accessories specified by the manufacturer Please email any comments questions about the manual to 8 Refer all servicing to qualified service personnel Servicing is required when the device has gt E mail customersupport keydigital com been damaged in any way including Damage to the power supply or power plug Exposure to rain or moisture Warranty Information You MUST Powar PPPI Brave WIN SOUL Bu u VOID i All Key Digital products are built to high manufacturing standards and should provide years of the Key Digital Warranty and risk damage to your unit and associated equipment a trouble free operation They are backed by a limited two year parts and labor warranty Mey digikza
13. l Mey cigiFal Mey cigiFal The Experts in Digital Video Technology and Solutions Key Digital led by digital video pioneer Mike Tsinberg j develops and manufactures high quality cutting edge technology solutions for virtually all applications where high quality video imaging is important Key Digital is at the forefront of the video industry for Home Theater Retailers Custom Installers System Integrators Broadcasters Manufacturers and Consumers 521 East 3rd Street Mount Vernon NY 10553 Phone 914 667 9700 Fax 914 668 8666 Web www keydigital com Rev O Jan 2011
14. library loaded during a factory reset This command will return the unit to its factory default settings including a user chosen default EDID setting See above for a list of possible default EDID library settings available Example To reset the unit to factory default with an EDID setting of 10801 2CH PCM issue the command SPCDFO1 Example To reset the unit to factory default with an EDID setting of 3D 1080p 2CH PCM issue the command SPCDFO7 Specifications Technical Input Each 1 HDMI 1 wired IR or RS 232 on 3 5 mm stereo jack connector per slot Output Each 1 HDMI 2 CAT5e 6 on RJ 45 connectors Bandwidth TMDS bandwidth 10 2 Gb s Control Front panel push buttons and LED s IR sensor front rear RS 232 Tx Rx lines with full bi directional operation Video Audio Matrix Switching Full matrix switching for HDMI DVI Video matrix RS 232 Control Matrix Full bi directional RS 232 input output Wired IR Control Matrix Each input output section wired IR and unit wired IR can be switched into matrix in bi directional operation to any of the inputs outputs EQ adjustment Precise auto adjustment distance measurement on Rx Balun or CAT 5e 6 Input Link and Range 1080p 60 1920x1200 max up to 75 ft 1080 60 720p 1080p 24 up to 100 ft Deep Color Support Digital video formats in Deep Color Mode at up to 10 bits color HDMI and HDCP Licensing Fully licensed and compatible with all HDMI
Download Pdf Manuals
Related Search