User manual
Contents
1. Tel 49 0 40 730 926 0 Fax 49 0 40 730 37 24 e mail info wassermann dental com Internet http www wassermann dental com2. casing e Pull the cable plug out of the handpiece b Assembly e Take the cable plug and insert it into the handpiece in the correct orientation e Tighten the motor cable swivel nut by turning it clockwise by hand Warning Do not use pliers i WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 7 Start up e Check that the rotating tool has been inserted up to the stop e Set the CONTROL switch to foot control e Turn the speed control knob to a low rpm setting e Set the POWER switch to ON it will light green e Push the foot switch the handpiece will run at the selected speed e There are two inbuilt safety features for your protection a notch at 30 000 rpm and a stop at 40 000 rpm 8 Troubleshooting Correcting errors 8 1 Faults Faults Likely cause Likely solution Red LED flashes Faulty cable Replace cable Overload block Open chuck on handpiece Thermal overload switch Turn unit off and allow to cool triggered Red LED stays on System error If the above recommendations do not solve the problem contact your dental depot or our Service department 12 WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 8 2 Technical data Voltage 220 240 V 50 60 Hz switchable 110 130 V 50 60 Hz Max power consumption unit 230 W Motor power output 160 W Max torque 7 5 Ncm Fuse T2 5A Motor speed 1500 50 000 rp
3. in dental laboratories using rotating tools 1 2 Safety symbols used in this manual Warning This is a warning of risk situations and dangers Failure to observe this warning could be life threatening These warnings must be observed lij Information This symbol draws your attention to specific features which must be observed 1 3 Safety guidelines Configuring and operating this equipment requires precise knowledge and observance of the instructions in this user manual The equipment is designed only for its intended application Servicing and repairs should be carried out only by authorised A specialists Make sure that the unit is connected to the correct mains voltage ix WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor Danger Do not touch the tool when it is rotating or coming to a stop Be sure to follow the manufacturer s guidelines for the maximum permissible speed of the rotating tools used Take the following precautions before starting work A e Wear eye protection e Use a protective visor 1 4 Handpiece block This rotary tool features electronically controlled overload protection If an excessive load blocks the handpiece the motor switches off automatically and the red LED flashes The handpiece stops if the chuck is open and the electronics also cut out if the tool starts working accidentally 1 5 Hesponsibility for operation and damage The responsibility for operating the
4. uot aaa t Re RUND RR RIDERE EE dE 5 2 2 GARE EE 6 2 3 CLEANING AND OR CHANGING THE CHUCK 6 Use le eet ee ee 7 Before you SUA ccc cscs Seen messen ea erana aAa ra EA saai eaae aeaa aE a mia aae sanaaa aiana sini ainas 7 4 1 UNPACKING TRANSPORT EE 7 4 2 el EE 8 5 SS realiter tec 8 5 1 POWER SWITCH EE 8 5 2 CONTROL ROCKER SWITCH RR RIESE ee 8 5 3 DIRECTION ROCKER SWITCH u cus ev datae ieee Cei c appo t ies 8 5 4 SPBEDSCONTROL KNOB dosent Renee ee 8 55 CHANGING ROTATING e dto ase dte eae ee ate o cS Rees 9 6 Installation rare ae een ence dha le ege ene e 9 6 1 INSTALLING THE MOTOR AND MAINS CABLES eese eene nnne nnne nnne nnns 9 6 2 ATTACHING THE MOUNTING RAS 2 2er ee 10 6 3 REMOVING AND ASSEMBLING THE MOTORISED HANDPIECE sssnnssssninssrirneserrrnesrrrrnene 10 SOUT 113 6 pe M 11 Troubleshooting Correcting errors uunssunsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nn 11 8 1 Eee c 11 8 2 TECHNICAL DICA o ette ee dedo ddan nenn dene 12 8 3 SPARE KE 12 8 4 REPAIRS an er 13 MER rur an ei 13 10 EG conformity certificate isisi enande een 14 We WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 1 For your safety 1 1 Correct use of this product This laboratory equipment is designed for working with dental materials stainless steels plastics ceramics etc
5. User manual HSM 500 rotary tool with knee control C WASSERMANN DENTAL MASCHINEN GMBH Ss WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor Dear customer Thank you for choosing a product from the Wassermann range Wassermann dental equipment incorporates the highest standards of quality and the latest technology In order to enjoy maximum performance and years of trouble free operation from the equipment please read this user manual carefully before you start work and operate the unit according to the recommended guidelines Please ensure that all persons operating the equipment have read and understood this user manual Keep this user manual on hand for ready reference Company address Wassermann Dental Maschinen GmbH Rudorffweg 15 17 D 21031 Hamburg Germany Tel 49 0 40 730 926 0 Fax 49 0 40 730 37 24 e mail info wassermann dental com URL http www wassermann dental com XR WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor GOTTEN c 2 WR e1 TE E A 3 1 1 CORRECT USE OF THIS PRODUCT u 3 1 2 SAFETY SYMBOLS USED IN THIS MANUAL A aaa 3 1 3 SAFETY GUIDELINES vitse acu chin coo ae E 3 1 4 HANDPIECE BLOCK nn inne 4 1 5 RESPONSIBILITY FOR OPERATION AND DAMAGE ccscsesscceeessceeecesseeeeesssseeeeeesseeeeesssaes 4 1 6 AUTHORIZED USERS nase auditu bae attt eus cedula cus een 5 2 Care and miainteriance E 5 2 1 MAINTENANGE
6. aboratory rotary Dental Maschinen GmbH tool for dental Rudorffweg 15 17 applications D 21031 Hamburg Model HSM 500 laboratory rotary tool with knee control 111995 Applicable EN 61010 1 1993 A2 1995 standards EN 60335 2 54 03 97 EN 50081 1 EN 50082 1 Hiermit wird best tigt dass die oben bezeichnete Maschine den genannten EG Richtlinien entspricht Diese Erkl rung wird ung ltig falls die Maschine ohne unsere Zustimmung ver ndert wird This is to confirm that the above mentioned machine complies with the described EC rules This declaration becomes invalid if the machine is modified without our approval Cette machine est conforme aux normes en vigueur de la Communit Europ ene Cet avis est nul et non avenant si cette machine est modifi e sans notre accord Esta maquina anteriormente mencionada cumple con los limites requeridos por el reglamento EC Ahora bien esta declaraci n quedar invalidada en caso de realizar modificaciones al aparato sin nuestra aprobaci n Hiermee wordt bevestigd dat bovengenoemde machine voldoet aan de voorgeschreven EU normen Deze verklaring verliest geldigheid als er zonder onze uitdrukkelijke toestemming wijzigen aan de machine worden aangebracht Place date Hamburg 10 April 2003 Company stamp Signed we pydorfiwed 197 7 rem Wassermann Managing Director p WASSERMANN DENTAL MASCHINEN WASSERMANN Dental Maschinen GmbH Rudorffweg 15 17 D 21031 Hamburg
7. h mild detergent Do not use chemical additives nen WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 2 2 Care il Remove external dirt from time to time with some form of cold cleaner Use only cold cleaners to avoid damaging the paintwork or removing the lettering Recommended A151 universal cleaner 2 3 Cleaning and or changing the chuck e Turn off the mains power e Open the chuck see 5 4 and remove the tip by turning it manually to the left e Insert the chuck key fully in the chuck e Hold the shaft firmly with an adjustable wrench e Remove the chuck by turning the chuck key to the left e Use a brush to clean the shaft and then lubricate the chuck and the bore with two drops of oil each e Insert the chuck by hand e Make sure that the chuck mechanism is still open e Insert the chuck key in the chuck and hold the shaft firmly with a wrench e Tighten the chuck up to the stop Ss WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 3 Use Application The HSM 500 is designed for working with dental materials such as stainless steels plastics ceramics etc in dental laboratories using rotating tools Warning This tool is not designed as medical equipment It is not to be used on human beings The tool is not to be used in areas where special conditions apply corrosive or potentially explosive atmospheres 4 Before you start 4 1 Unpac
8. king Transport Open the cartons remove the packing materials and carefully lift out the instrument and accessories Check the accessories are correct When transporting the unit use appropriate packing materials to avoid accidental damage il Locate the user manual and read it carefully When unpacking it is important to identify any accidental transport damage If necessary draw up an immediate status report Warning Before starting the tool check on the right side of the A controller to make sure it is set to the correct voltage 230 V or 115 V If it is not use a screwdriver to set it correctly SCH WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 4 2 Contents 111100 Handpiece 592013 Mains cable 111102 HSM 350 500 cable 111107 Mounting rail 111103 Handpiece holder 208210 DIN 7971 screws 111895 Knee control 111150 Cleaning set 5 1 POWER switch The POWER switch turns the controller ON OFF When the unit is on the mains switch lights green 5 2 CONTROL rocker switch This switch enables you to control the tool by hand or knee 5 3 DIRECTION rocker switch The DIRECTION rocker switch controls the direction of rotation of the handpiece 5 4 Speed control knob This knob is used to set the desired rom When you operate the foot control or switch to manual operation the handpiece comes up to the set speed The unit has two safety reminders at 30 000 and 40 000 rpm you will detect increased
9. m Duty cycle S6 Amin 10 min Height 84 mm Width 215mm Depth 277mm Weight 4 85 kg il Noise emission lt 70db A il We reserve the right to make technical changes 8 3 Spare parts Spare parts 1 111154 Adjustable wrench 1 1 111106 3 mm chuck i WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 8 4 Repairs Servicing or repairs to the unit must only be carried out by trained technicians Only original spares are to be used Responsibility for the product is voided if altered by unauthorized persons or if inappropriate components are installed 9 Warranty The warranty period for our equipment is 12 months If faults occur within the warranty period contact your dental depot or get in touch directly with our Service department Your rotary tool should only be operated in perfect condition If faults occur which could harm operators or third parties the unit should not be used until it has been fixed This warranty does not cover damage caused by improper use external mechanical causes transport damage or interference with the unit by unauthorized persons id WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 10 EC conformity certificate in accordance with 73 23 EWG low voltage guidelines modified by 93 68 EWG and 89 336 EWG EMV guidelines and 89 392 EWG Machinery guidelines with modifications Manufacturer WASSERMANN Product description L
10. rotational resistance bd WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 5 5 Changing rotating tools Rotating tools can only be changed when the motorised handpiece has stopped completely Dangerous e Turn the handpiece casing to the right to open the chuck e Remove the rotating tool e Push in the new tool until you feel the stop e Turn the handpiece casing to the left you will feel and hear it clicking into place Warning Always turn the handpiece casing up to the stop 6 Installation 6 1 Installing the motor and mains cables At the rear of the controller e Insert the motor cable 5 pole into its socket and turn it to the right e Insert the mains cable into the socket on the tool e Turn the tool on at the mains The tool is now ready for operation Ss WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 6 2 Attaching the mounting rails Use the hole template supplied or the 7 ex mounting rails The tool must be mounted on the right hand side Pre drill 3 mm holes then screw in the rails firmly using the screws provided Allow for the following dimensions The first hole must be drilled min 65 mm from the underside of the bench top and min 85 mm from the forward edge of the bench 6 3 Removing and assembling the motorised handpiece a Removal Turn the POWER switch to OFF e Undo the motor cable swivel nut from the handpiece
11. unit lies exclusively with the owner or user if the said unit is incorrectly serviced maintained or altered by persons not employed by an accredited dealer or if the unit is used in a manner contrary to its specified purpose The unit must be maintained and operated in accordance with this user manual Wassermann Dental Maschinen GmbH is not responsible for damage arising from the non observance of these instructions Guarantee and responsibility provisions contained in the sales and supply conditions of Wassermann Dental Maschinen GmbH are not extended by these instructions Product responsibility lapses if the equipment is altered by unauthorized third parties or if non original parts are installed Use only original WASSERMANN replacement parts ms WASSERMANN DENTAL MASCHINEN Die Basis f r Ihr Labor 1 6 Authorized users The owner of the equipment must ensure that any users have been provided with the user manual and that they have read and understood its contents before operating the equipment lij Ensure that this user manual is accessible at all times and has been read and understood 2 Care and maintenance 2 1 Maintenance Always disconnect the power cable before undertaking cleaning or maintenance The model plate must always be legible and should not be removed The equipment should be cleaned at regular intervals to ensure trouble free operation It requires only normal cleaning sponge damp clot
Download Pdf Manuals
Related Search