User`s Manual
Contents
1. 1 Loudspeaker enclosure hightech moulding material flame retardant class VO according to UL94 with textured paint finish 2 1st safety bar for 5 mm chain quick link quick link not included in purchased parts package 3 Locking hole for aligning the optional accessory Adjustable Speaker Mount PASSIO and Pin Joint Adapter PASSIO in 90 intervals 4 Mounting point K amp F VariPoint for mounting the optional accessory Adjustable Speaker Mount PASSIO or Pin Joint Adapter PASSIO uses M10 bolt or the quick connector KF Fixing Pin 5 2x Speakon connector 4 pin NLTAMP parallel 6 2nd safety bar for 5 mm chain quick link quick link not included in purchased parts package KLING amp FREITAG GMBH 2012 Revision 2 2 Page 6 of 24 User s manual 2 3 Accessories Adjustable Speaker Mount PASSIO pin fix ing with Fixing Pin and clamp lever For quick connections using the K amp F VariPoint with the undetachable fixing pin Can be mount ed in a vertical or horizontal position without ad ditional accessories Colour black or white Adjustable Speaker Mount PASSIO screw fixing with screw and nut M10 For use with the K amp F VariPoint using a screw M10 Can be mounted in a vertical or horizontal position Colour black or white Pin Joint Adapter PASSIO pin fixing with Fixing Pin and clamp lever For quick mounting of the PASSIO on i e a Super2. User s manual K amp F PASSIO 4 2 Passive Mode without Controller The PASSIO system is designed so that it can be operated passively without a controller directly on a power amplifier Follow the instructions in chapter Protecting the Speakers Operating Safety be ginning on page 10 For safe operation they must only be operated with professional power amplifiers with a maxi mum rated output power of 600W080 equiv 1200W 4Q If power amplifiers have power ratings lower than 300W 8Q then it is imperative that the am plifiers have clipping limiters Alternately you can also insert a clipping limiter before the ampli fier To protect the loudspeaker from mechanical damage when high SPL is required a highpassfilter of 24dB oct at 60Hz has to be inserted into the signal chain 1 1 PASSIO im WA KLING amp FREITAG GMBH 2012 Revision 2 2 Page 15 of 24 User s manual K amp F PASSIO 5 Wiring instructions Before connecting your PASSIO loudspeaker switch off all equipment and turn down all level controls Only use high quality speaker cables with a sufficient wire gauge The wire gauge depends on the length of the speaker cable Minimum Wire Gauge mm Required Cable Length m 2 x Speaker Impedance Q For connections to the power amplifier inputs please use 2 pin shielded microphone cable bal anced wi
3. If there is interference turn off all appliances in the reverse order and check all cable connec tions Successively turn up the individual power amplifier channels and send a signal with low vol ume to the system Check to see if the desired signals are applied to the intended speakers and make sure there is no interference With controller The SIGNAL LEDs of the CD 44 Controller will light up if the output level is higher than 45 dB Your system should now be ready for operation Turning down the input level controls may not always prevent distortions in the input section of the power amplifier especially if this section has a relatively low headroom A clipping signal may not be displayed by the clipping indicator then To prevent signal interruptions or damages to the speakers turn the level controls of the power amplifier to the maximum position if possi ble Set the output level of the mixing console or the controller to a level that doesn t overload the power amplifiers or decrease the limiter threshold of the controller When turning off the system the input controls for the power amplifiers should be turned down first followed by the power switches of the amplifiers After that the other appliances can be turned off KLING amp FREITAG GMBH 2012 Revision 2 2 Page 16 of 24 Warning User s manual K amp F PASSIO 7 Transport and Storage The PASSIO is protected against short term moisture not_found The PASSIO Syste
4. cause malfunctions or property damage This symbol indicates notes that help you to handle the described products easier 1 2 Information about this User s Manual Kling amp Freitag GmbH all rights reserved All specifications in this manual are based on information available at the time of publishing for the features and safety guidelines of the described products Technical specifications measurements weights and properties are not guaranteed The manufacturer reserves the right to make product alterations within legal provisions as well as changes to improve product quality All persons who use the speaker system must have this guide and all further information for safe operations available to them during assembly disassembly and use The speaker system may neither be set up nor used until this manual has been read understood and kept readily available on site We appreciate any input with suggestions and improvements for this manual Please send this to us at the following address info kling freitag de or to KLING amp FREITAG GMBH Junkersstr 14 D 30179 Hannover Phone 49 0 511 96 99 70 Fax 49 0 511 67 37 94 KLING amp FREITAG GMBH 2012 Revision 2 2 Page 5 of 24 User s manual K amp F PASSIO 2 Product Description 2 1 Scope of Delivery Speaker with integrated mount for optional fastener with Pin Joint Adapter or Adjustable Speaker Mount not found 2 2 Overview of Components 1 JO
5. Clamp or a TV Spigot using the Fixing Pin Colour black Pin Joint Adapter PASSIO screw fixing with screw and nut M10 For direct mounting of the PASSIO to i e a Super Clamp or a TV Spigot with a threaded bolt M10 Colour black Super Clamp with threaded pin M10 for pipes or plates from 13 to 50 mm for loads up to 15 kg For use with the Adjustable Speaker Mount PAS SIO the additional accessory Mini TV Spigot is re quired Colour black KLING amp FREITAG GMBH 2012 Revision 2 2 K amp F PASSIO Page 7 of 24 User s manual K amp F PASSIO Mini TV spigot with internal M10 thread Necessary for suspending the Adjustable Speaker Mount with a Super Clamp jJ for use with the accessory Adjustable speaker Du mount PASSIO with a Super Clamp Colour black Stand Socket M10 for use with the Adjustable Speaker Mount PAS SIO on a stand for use with other adjustable speaker mounts a fixing screw M10 x 25 a washer and a lock wash er in black are included Colour black Examples of use Application example Adjustable Speaker Mount Application example Adjustable Speaker Mount PASSIO with stand adapter M10 PASSIO with Mini TV Spigot and Super Clamp on a horizontal pipe Application example Pin Joint Adapter PASSIO Application example Pin Joint Adapter PASSIO with Super Clamp on a horizontal pipe with Super Clamp on a ver
6. IO Frequency response on axis Frequency response Impedance 100 160 140 90 EEE 1 LLI 120 5 100 m 2 80 so 8 7 E 60 amp E 70 Ltt 40 20 60 20 100 1000 10000 40000 Frequency Hz s cil BassBoost mode Frequency response on axis ze LCut mode 10 0 wia si 10 20 Sian _ LH 30 20 100 1000 10000 40000 Frequency Hz KLING amp FREITAG GMBH 2012 Revision 2 2 Page 20 of 24 User s manual 10 2 Coverage PASSIO Horizontal 125 250 500 1k 2k f Hz Vertical 4k 8k 16K 125 250 500 1k 2k KLING amp FREITAG GMBH 2012 4k 8k Revision 2 2 16K 180 150 120 90i 60i 30i Oj 30i 60j 90j 120j 150j 180j 180i 150i 120i 90i 60 30j 6i 30i 60j 90i 120i 150j 180j K amp F PASSIO Attenuation dB H lt 3 M3 6 6 9 Mo 12 WMi2 15 WM 15 18 gt 18 Attenuation dB E lt 3 M3 6 6 9 Mo9 12 H12 15 H 15 18 gt 18 Page 21 of 24 User s manual K amp F PASSIO 11 Dimensions Yo 173 3
7. K amp F PASSIO User s Manual Important Information Please Read Before Use KLING amp FREITAG GmbH JunkersstraBe 14 D 30179 Hannover PHONE 49 0 511 96 99 70 FAX 49 0 511 67 37 94 www kling freitag de Version 2 2 Released 08 03 2012 KLING FREITAG SOUND SYSTEMS User s manual K amp F PASSIO Table of contents 1 Introduction 5 1 1 Symbols in User s Manual 5 1 2 Information about this User s Manual 5 2 Product Description 6 2 1 Scope of Delivery 6 2 2 Overview of Components 6 2 3 Accessories 7 2 4 Required Tools 8 3 Safety Instructions 10 3 1 Mounting the Speakers Wall and Ceiling Installation 10 3 2 Notes for Mounting the Speakers 10 3 3 Preventing hearing damage 10 3 4 Protecting the Speakers Operating Safety 10 4 Configuration and Connecting Diagram 12 4 1 Use with Controller CD 44 12 4 1 1 Controller Mode Full Range 12 4 1 2 Operations with Controller and Subwoofer 13 4 1 3 Controller Mode with Subwoofer in Overlap Mode 13 4 1 4 Controller Mode with Subwoofer in 1 Channel Mode 14 4 2 Passive Mode without Controller 15 5 Wiring instructions 15 6 Operating the Speakers 16 7 Transport and Storage 17 8 Maintenance and Care 17 8 1 Inspection Regulations 17 8 2 Replacing the Front Foam 18 9 Technical Specifications 19 10 Measuring diagrams 20 10 1 Frequency range PASSIO 20 10 2 Coverage PASSIO 21 11 Di
8. Rack Main out PCR AGUA NE Activate the filter Cluster for the top speakers If you need a boost in the high frequency range via Filter B if you wish to operate several tops next e g for compensating the high frequency at to one another tenuation for larger distances activate the filter HighBoost via Filter B for the top speakers FILTER B FILTER B If necessary adjust the correct level balance with the output gain of the subwoofer on the CD 44 KLING amp FREITAG GMBH 2012 Revision 2 2 Page 13 of 24 Vd Tip User s manual K amp F PASSIO 4 1 3 Controller Mode with Subwoofer in Overlap Mode In full range mode the speaker PASSIO is compatible with all K amp F subwoofers that are run in the 100Hz mode This so called overlap mode can make sense for surround uses when the tops should transmit the complete frequency spectrum and the subwoofer is used as an effect bass In the overlap mode the bass boost must not be switched on 4 1 4 Controller Mode with Subwoofer in 1 Channel Mode You can operate the speaker PASSIO together with several K amp F subwoofers on a single controller channel To do so load the matching LSBlock for the speaker combination into the controller For fur ther information please see the user s manual of the subwoofers that are suitable for 1 channel mode e g NOMOS LS KLING amp FREITAG GMBH 2012 Revision 2 2 Page 14 of 24
9. consis tent solutions for the disposal throughout Europe Responsible for complying with these provisions of law is the local distributor importer of each coun try For proper disposal of used products in accordance with these local provisions in the mentioned coun tries of the European Union except Germany please ask your local dealer or the local authorities 12 1 3 All other Countries For proper disposal of used products in accordance with local provisions in other than the above men tioned countries please ask your local dealer or the local authorities KLING amp FREITAG GMBH 2012 Revision 2 2 Page 23 of 24 User s manual K amp F PASSIO KLING amp FREITAG GMBH 2012 Revision 2 2 Page 24 of 24
10. ing damage Avoid beeing too close to operating speakers This equipment is capable of delivering sound pressure levels in excess of 90 dB SPL which may cause permanent hearing damage KLING amp FREITAG GMBH 2012 Revision 2 2 Page 10 of 24 User s manual K amp F PASSIO 3 4 Protecting the Speakers Operating Safety In general audio signals must not be overdriven This may be caused by mixing consoles equalizers effect equipment etc and should be indicated on this equipment We therefore recommend turn ing up the power amplifiers all the way and adjusting the level before the power amplifier in order to avoid overloading the input circuit In any case the signal must be reduced as soon as it sounds un naturally distorted not_found Operations without K amp F SystemRack To protect the speakers from being destroyed and to avoid fire hazard they should only be op erated with professional power amplifiers with a maximum rated output power of 600W 8Q If power amplifiers have power ratings lower than 300W 8Q then it is imperative that the am plifiers have clipping limiters Alternately you can also insert a clipping limiter before the ampli fier Power amplifiers can also be overloaded at the input circuit without the amplifier signalling the clipping i e when there is not sufficient headroom in the input circuit To protect the loudspeaker from mechanical damage when high SPL is required a highpa
11. m is not designed for long term use in a corrosive environment Make sure that the system is adequately ventilated during longer storage periods so that possible residual moisture can escape from the equipment Furthermore you should ensure that the PASSIO System is protected from mechanical strain to prevent possible damage We recommend using suitable transport and storage cases that protects from the above mentioned in fluences 8 Maintenance and Care 8 1 Inspection Regulations For the owner and user it is mandatory to be aware of the safety relevance of speakers that can be flown Please note that the mains cables are delivered with varying connector options or with open wires mains side depending on the country or order number The PASSIO system can exhibit signs of wear over the years i e from mechanical strain transport damage corrosion or improper handling If speakers are to be flown this always means there is a high safety hazard As a basic principle you must visually inspect the PASSIO System every time you suspend it and take it down For fixed installations you must inspect the speaker for signs of wear at regular intervals During these inspections you must especially look out for deformations cracks dents damage to threads and corrosion Mounting devices such as shackles chains and wire ropes also have to be checked for signs of wear or deformation carefully not_found PASSIO The inspection re
12. mensions 22 12 Disposal 23 12 1 Regulations for Disposal 23 12 1 1 Germany 23 KLING amp FREITAG GMBH 2012 Revision 2 2 Page 3 of 24 User s manual K amp F PASSIO 12 1 2 EU Norway Iceland and Liechtenstein 23 12 1 3 All other Countries 23 KLING amp FREITAG GMBH 2012 Revision 2 2 Page 4 of 24 A Warning A Caution Vd v Tip User s manual K amp F PASSIO 1 Introduction Thank you for your decision to buy a KLING amp FREITAG product To guarantee a trouble free operat ing of the equipment and to allow your KLING amp FREITAG PASSIO system to achieve its full potential please read the operating instructions carefully before use With the purchase of a PASSIO you have acquired a large sound system with the highest possible quality and performance capabilities As the owner of a PASSIO loudspeaker you now have a versatile and highly professional tool which when operated properly is a true pleasure to use 1 1 Symbols in User s Manual This symbol indicates the possibility of life threatening danger and a health risk for persons Not fol lowing these instructions may result in serious health problems including potentially fatal injuries This symbol indicates a possibly dangerous situation Not following these instructions may cause minor injuries or cause property damage This symbol gives instructions for the proper use of the described products Not following these in structions may
13. mm u aa 6 823 inch 55 KLING amp FREITAG GMBH 2012 Ve C K amp F VariPoint Coo 415 3 mm e 16 352 inch oo e a mum 207 7 mm 0 B 176 inch 5 e o L pom i y O a 179 9 mm 90 mm 7 083 inch 3 542 inch 25 e Revision 2 2 Page 22 of 24 User s manual K amp F PASSIO 12 Disposal Please recycle the packaging material of the device 12 1 Regulations for Disposal 12 1 1 Germany It is not allowed to dispose of used electrical equipment as domestic waste But please do not dispose of them at official collecting points for recycling either All KLING amp FREITAG products are plain business to business B2B products KLING amp FREITAG prod ucts labelled with a waste bin sign have thus to be disposed of by KLING amp FREITAG alone Please call KLING amp FREITAG at the number stated below if you have a KLING amp FREITAG product to be disposed of We will offer you a straightforward and professional disposal with no costs involved If there is no waste bin sign on one of your KLING amp FREITAG products because it has been sold be fore 24 March 2006 then by law the owner is in charge of the disposal In this case we will be happy to assist and offer you proper ways of disposal Telephone number to call about the disposal of used KLING amp FREITAG products 49 0 511 96 99 7 0 Explanation With the Elekt
14. monitors except flat panels KLING amp FREITAG GMBH 2012 Revision 2 2 Page 11 of 24 User s manual K amp F PASSIO 4 Configuration and Connecting Diagram 4 1 Use with Controller CD 44 When operating the loudspeaker with amplifers without clipping limiter and nominal amplifier pow er less than 300W 8Q requires to set a Limit Reduction of 3dB for the K amp F CD 44 controller You can find more detailed information about this option in the K amp F CD 44 hardware manual 4 1 1 Controller Mode Full Range If you want to operate the speaker in fullrange mode then select the LSBlock PASSIO FR in the CD 44 for the PASSIO PASSIO K amp F CD 44 Loaded LSBlocks K amp F SystemRack S O To next en 2 AMAA ANS via Filter B if you wish to operate several tops next BassBoost via Filter B for the top speakers to one another FILTER B FILTER B KLING amp FREITAG GMBH 2012 Revision 2 2 Page 12 of 24 User s manual K amp F PASSIO 4 1 2 Operations with Controller and Subwoofer If you want to operate the PASSIO with an additional K amp F subwoofer then select the LSBlock PASSIO LCut in the CD 44 for the PASSIO K amp F CD 44 Loaded LSBlocks CH 2 1 1 PASSIO Amp 1 Output CH 2 Amp 1 Output CH 1 NOMOS LS K amp F SystemRack j To next System
15. quirements vary depending on application and country of use Observe the requirements that are relevant for you If in doubt contact local authorities In many countries regular inspection of mounting components and accessories is required In most cases e g german BGV C1 an additional annual inspection is required that must be done by a tech nical expert Additionally a detailed inspection carried through by a legally certified or official authori ty is required every four years In this context it is very important to keep an inspection log book In this inspection log book the da ta for every used accessory is entered at the periodic inspections making the data available at all times for possible inspections This book should document maintenance measures and inspection intervals and contain parts lists KLING amp FREITAG GMBH 2012 Revision 2 2 Page 17 of 24 v Tip User s manual K amp F PASSIO 8 2 Replacing the Front Foam The front foam behind the front grille is held in place by an elastic band This makes it possible for you to easily replace the damaged or soiled foam yourself 1 Remove the grille attachment screws with a 2 5mm Allen key Remove the grille from the speaker Remove the old filter foam behind the elastic band Pull the new or cleaned filter foam behind the elastic band a AU ge Fasten the grille back onto the speaker using the attachment screws In doing so make sure that the clamping nu
16. roG law relating to electrical and electronic equipment and appliances we have complied with the EU directive on waste electrical and electronic equipment WEEE 2002 96 EC From 03 24 2006 onwards KLING amp FREITAG GmbH has thus labelled all products mentioned in the WEEE with a sign with a crossed out waste bin and a white bar below This sign indicates that the disposal as domestic waste is prohibited and that the product has been put into circulation on 03 24 2006 at the earliest KLING amp FREITAG GmbH has been legally registered as a manufacturer with the German registration office EAR Our WEEE registration number is DE64110372 For the German Registration office EAR we have accredited that our products are soleB2B products 12 1 2 EU Norway Iceland and Liechtenstein It is not allowed to dispose of used electrical equipment as domestic waste From 08 13 2005 onwards KLING amp FREITAG GmbH has thus labelled all products for EU Member countries as well as Norway Iceland and Liechtenstein except Germany mentioned in the WEEE with a sign with a crossed out waste bin and a white bar below This sign indicates that the disposal on domestic waste is prohibited and that the product has been put into circulation on 08 13 2005 at the earliest Unfortunately the European directive WEEE has been complied with implementing different national provisions of law throughout all member countries which makes it impossible for us to offer
17. ssfilter of 24dB oct at 60Hz has to be inserted into the signal chain Operations with K amp F SystemRack For optimal performance and operating safety of the PASSIO speakers we recommend using the K amp F SystemRack When a power amplifier is overloaded at the output clipping then the amplifier activates a clipping warning signal For damage caused by overloading the speakers using power amplifiers with other than the recommended maximum output power we do not assume warranty and excludes liability for possible consequential damage The following signals may damage the speakers clipping power amplifiers permanent high level signals with high frequency and continuous noise from feedback permanently distorted high level signals noises which occur when the amplifier is on while equipment is being con nected disconnect ed or switched on Do not install devices in any of the following places where the devices are permanently exposed to direct sunlight where the devices are exposed to high moisture or rain where the devices are exposed to strong vibrations and dust Avoid damage caused by the speakers magnetic fields Speakers are permanently surrounded by a magnetic field even when they are not connected There fore during transport and placement of the speakers it is important to ensure that there is a sufficient distance between the speakers and magnetic data media and computer video
18. sure to comply with the stipulated tightening torques If not otherwise stated in this manual only original KLING amp FREITAG parts may be used for mount ing the speakers The use of other parts in particular parts by other manufacturers is not permitted in this case Ensure that all installation connections comply with the applicable safety guidelines and that the size and strength are sufficient Ensure that all connections are secured against coming loose and that only authorized statically tested and correctly sized supports mounting equipment wire ropes and chains are used As a basic principle you must visually inspect all safety relevant components of the speaker and the accessory before every use If there are signs of wear cracks or deformation then you must replace the parts immediately The visual inspection also includes checking the screwed connections on sup porting elements The information described here does not relieve the user of the duty to follow the given safety re quirements and legal regulations 3 2 Notes for Mounting the Speakers Mount the speakers securely To avoid injury or damage always be sure to mount the speakers secure ly so that they do not fall Please note that speakers can move as a result of vibrations To prevent them from falling from their mounted position they must be secured properly When laying out the connecting cables make sure that nobody can trip 3 3 Preventing hear
19. th high quality connectors Avoid ground loops Please pay attention to the pin assignments shown in this manual Make sure that the polarity of the speakers at the amplifier is correct When simultaneously using power amplifiers from different manufacturers be sure to use the correct specific pin con figuration It may be necessary to modify the pin configuration on the power amplifiers or on the connectors leading to them Upon completing the wiring ensure that the connected speaker channels are working in phase To do so use i e a phase checker A phase error can also be recognized when the connected channels are used simultaneously During simultaneous use the bass frequencies become no tably quieter or the mid frequencies such as voices cannot be located If several loudspeakers are connected the signal can be linked through parallel from one loud speaker to the next Please make sure that the total impedance of the loudspeakers R Q is not lower than the minimal impedance indicated on the power amplifier 1 R1 1 R2 1 R3 1 Rtotal 6 Operating the Speakers Switch off all equipment and turn down all level controls of the mixing console and the power amplifiers Wire your PASSIO systems according to the instructions in this manual Switch on the mixing console first then the controller and the power amplifier Always use the before mentioned switching order Otherwise switching noises may damage the sound system
20. tical pipe KLING amp FREITAG GMBH 2012 Revision 2 2 Page 8 of 24 User s manual K amp F PASSIO 2 4 Required Tools For front foam replacement 2 5 mm Allen head wrench KLING amp FREITAG GMBH 2012 Revision 2 2 Page 9 of 24 Warning A Warning A Caution User s manual K amp F PASSIO 3 Safety Instructions 3 1 Mounting the Speakers Wall and Ceiling Installation not found The speakers may only be mounted by qualified event technicians or personnel which are instructed by them adequately This also applies for wall and ceiling fixations The technicians responsible for assembling the speakers on site are responsible for the safe setup and use of the speakers and guarantee this Never use signal cables or power cords for suspending aligning or securing the systems Before carrying through ceiling and wall installations it is essential to consider the load capacity of walls ceilings and panelling as well as the stability and type of the construction If there is wall pan elling for example it is then necessary to examine the solidity of the wall and use the appropriate wall plugs Note that the suspension points on the hall ceiling i e shackles suspension points or chain points must comply with the accident prevention regulation BGV C1 Event and Production Sites for Stage Presentations or comparable applicable national standards and the total load must be approved by an authorised expert Make
21. ts on the grille mounting flaps are aligned with the drill holes in the enclosure You can set the clamping nuts into the proper position using the Allen key before applying the screws KLING amp FREITAG GMBH 2012 Revision 2 2 Page 18 of 24 User s manual K amp F PASSIO 9 Technical Specifications Design Frequency range 10 dB Frequency range 3 dB Coverage angles nominal Power Handling SPL 1W 1m Max SPL 1m Components Impedance nominal Connectors Enclosure Dimensions Weight Options Passive 2 way bassreflex system 75 Hz 31 kHz 110 Hz 28 kHz 70 x 60 H x V 200 W nominal 400 W program 92 5 dB SPL 21 5 dB SPL 2 x 5 low mid chassis Dome tweeter plus cd horn 2 Q Zmin 8 Q 200 350 Hz 1 1 2 x Speakon 4 pol NLT4MP IN parallel with OUT high tech moulding synthetics with 25 and 55 monitor angles flame retardant class VO accord ing to UL94 K amp F VariPoint to fasten hardware sunk in and to the bottom faced Speakon con nectors 5 angle on top and bottom for incon spicious design textured paint finish in black ex changeable front grille with black acoustic foam behind it 180x415 x 173 mm 5 2 kg Special finish in RAL colours 1 Pink noise 40 5000 Hz 2 h 2 as 1 but with 5096 duty cycle KLING amp FREITAG GMBH 2012 Revision 2 2 Page 19 of 24 User s manual K amp F PASSIO 10 Measuring diagrams 10 1 Frequency range PASS
Download Pdf Manuals
Related Search