DIALighting IW7-10 USER MANUAL
Contents
1. Show Atelier DIALighting IW7 10 GAL USER MANUAL PLEASE KEEP THIS FOR FUTURE USE 9 Maintenance and Cleaning The following points have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling Suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation soot and usage have to be adhered by a skilled installer and any safety problems have to be removed a gt CAUTION Disconnect from mains before starting maintenance operation In order to make the lights in good condition and extend the life time we suggest a regular cleaning to the lights 1 Clean the inside and outside lens each week to avoid the weakness of the lights due to accumulation of dust 2 Clean the fan each week 3 Adetailed electric check by approved electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There2. in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class Therefore it is essential that the device be earthed The electric connection must carry out by qualified person The device shall only be used with rate voltage and frequency Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up Some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually Please don t project the beam
3. are no serviceable parts inside the device Please refer to the instructions under Installation instructions 10 7 Unpacking Thank you for choosing our products For your own safety please read this manual before installing the device This manual covers the important information on installation and applications Please install and operate the fixture with following instructions Meanwhile please keep this manual well for future needs Super beam light is made of a new type of high temperature strength of engineering plastics and cast aluminum casing with nice outlook The fixture is designed and manufactured strictly following CE standards complying with international standard DMX512 protocol It s available independently controlled and linkable with each other for operation And it is applicable for large scale live performances theater studio nightclubs and discos The adopt 7pcs 10W LEDs which features high brightness and stability Please carefully unpack it when you receive the fixture and check whether it is damaged during the transportation And please check whether the following items are included inside the box Moving Head One Signal Cable One Hanging Bracket One Power Cable One User Manual One 2 Safety Instructions CAUTION Be careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory
4. east one properly rated safety cable to the fixture using on of the safety cable rigging point integrated in the base assembly y eines SURI TR D Omega Bracket Satety Clamp Safety Cable 1 4 Turn Quick Lock Fasteners al Turn around Turn ground Regardless of the rigging option you choose for your LED super beam always be sure to secure your fixture with a safety cable The fixture provides a built in rigging point for a safety cable on the hanging bracket as illustrated above Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle
5. for beam light and effect use 12 channels mode Don t turn on the fixture if it s been through severe temperature difference like after transportation because it might damage the light due to the environment changes DMX Value Description So make sure to operate the fixture until it is in normal temperature 0 255 0 540 degree 0 255 0 270 degree Pan Tilt soeed 0 255 Pan Tilt soeed from fast to slow 0 127 The distance between beams from Lens near to far Angle from small to big rotation Beam 201 255 Rotation without limitation from slow to fast Color wheel 0 255 Color wheel rotation 0 255 Linear dimming from dark to bright 0 255 Strobe from slow to fast Led 7 dimming 0 255 Linear dimming from dark to bright EA Led 1 LED 6 0 255 Linear dimming from dark to bright dimming Black out Static effect 1 10 This light should be keep away from strong shaking during any transportation or movement Don t pull up the light by only the head or it might cause damages to the mechanical parts Don t expose the fixture in overheat moisture or environment with too much dust when installing it And don t lay any power cables on the floor Or it might cause electronic shock to the people Make sure the installation place is in good safety condition before installing the fixture Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture Make sure the lens are in good condition It
6. llations where the DMX cable has to run a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 1200 2 3 7 PIN3 PIN 2 Mounting points Overhead mounting requires extensive experience including amongst others calculating working load limits a fine knowledge of the installation material being used and periodic safety inspection of all installation material and the fixture If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet Clamp Mounting The LED BEAM provides a unique mounting bracket assembly that integrates the bottom of the base the included Omega Bracket and the safety cable rigging point in one unit see the illustration below When mounting this fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a M10 screw fitted through the center hole of the omega bracket As an added safety measure be sure to attached at l
7. onto combustible substances Fixtures cannot be installed on combustible substances keep more than 50cm distance with wall for smooth air flow so there should be no shelter for fans and ventilation for heat radiation lf the external flexible cable or cord of the luminaire was damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard 19 channels mode DMX 0 255 0 270 degree Pan fine adjustment 0 255 16bit 0 255 0 540 degree P Tilt fine adjustment 0 255 16bit Pan Tilt speed 0 255 Pan Tilt speed from fast to slow The distance between beams from near to far Angle from small to big Rotate Clockwise unlimited from fast to slow Counter clockwise unlimited from slow to fast 0 127 128 190 191 255 Lens rotation Beam Led 5 dimming 0 255 inear dimming from dark to bright at 1 er 1 T Led 3 dimming 0 255 Linear dimming from dark to bright Led 4 dimming 0 255 Linear dimming from dark to bright T oat 1 1 Led 7 dimming 0 255 inear dimming from dark to bright eee Ce Dynamic effect 39 Static effect 40 8 4 7 10 233 235 8 2 Led 6 dimming 0 255 inear dimming from dark to bright Light effects show Speed of effects show 0 255 From fast to slow Reset within 6 seconds Channel 7 10 11 12 13 14 15 16 18 19 3 Operation Instructions 8 DMX Channels details The moving head is
8. rotection mount the fixtures in areas outside walking paths seating areas or in areas were the fixture might be reached by unauthorized personnel Before mounting the fixture to any surface make sure that the installation area can hold a minimum point load of 10 times the device s weight Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable Never stand directly below the device when mounting removing or servicing the fixture From a ceiling or ser on a flat level surface see illustration below Be sure the fixture is kept at least 0 5 m away from any flammable materials Always use and install the supplied safety cable as a safety measure to prevent accidental damage caused by the clamp fails 7 Control Panel Menu Instruction Menu Panel Set the DMX address Pan auto Run Tilt auto Run LENS auto Run RP ON RT ON 6 DMX 512 control connections Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head You can chain multiple Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below DMX 512 connection with DMX terminator Controller DMX Output DMX Input COMMON 3 Pin XLR Socket 3 Pin XLR Socket 559 sur de En a SPNXIR Lo ow oz SPNXR For insta
9. s recommended to replace the units if Dynamic effect 1 ac show RS there are any damages or severe scratch Make sure the fixture is operated by qualified personnel who knows the fixture before using Keep the original packages if any second shipment is needed Don t try to change the fixtures without any instruction by the manufacturer or the appointed repairing agencies It is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation like shock short circuit electronic shock lamp broke etc 4 Specifications Voltage AC90 240V 50 6012 Power 90W Led source 7pcs high brightness 10W CREE white LEDs Beam angle 5 40 Strobe 1 25 Hz Dimmer 0 100 linear dimmer with 16 bit without strobe Pan 540 fine Tilt 250 fine Color With a 6 colors wheel to create colorful effect Channel 12 19 DMX double channels mode Control DMX512 Master slave Auto Sound activated Function 1 Strong beam light effect beam angle is optional beam light with macro effect 2 Each bulb is controllable with racing light effect 3 B eye designed Lens can rotate without limitation to create dynamic and amazing effect Can separate to colorful beams or gather to one strong beam 4 Perfect beam light and effect light for disco club show etc 5 Smaller size but excellent effect to make installation as easy as you can imagine 5 Installation instruction Cautions For added p
Download Pdf Manuals
Related Search