USC128 Universal DMX Controller
Contents
1. to damaging the device starting a fire or its wrong function Power cord Check if power cord is not mechanical damaged and if it is connected properly Check also if the socket is designed sufficiently for needed loading Otherwise there is a danger of electric shock or a fire Power cord must not be bent excessively led through sharp edges or given to mechanical stress Don t pull the supply lead out by the flex but only by the plug The device must always be connected behind the main switch Do not touch the supply lead with vet hands you are threatened by electric shock Maintenance and cleaning Don t use any solvent and similar chemicals which could damage surface finish or some parts of device Use soft and smooth cloth for cleaning parts of device and its surface Never use washing powders or other cleaning agents with grinding effect Connect the device to power supply after complete drying Service Never try to repair dismantle or do some construction changes in case of any failure Always consult qualified employee or dealer Not keeping this rule you can suffer dangerous electric shock Unpacking Unpack the device and after acclimatisation take off the protective foil Make sure that there are no damages caused by transportation Installation The device can be installed in any position without altering its operation Before removal of the cover you must be sure that device is switched off Otherwise you risk damaging el2. you chose required value from 0 00 to 5 10 sc and deactive it The basic adjusted mode of the controller is PULSE 13 mode that means making 5 ms It means we can control this device by any other device which provides signal included in protocol DMX 512 by serial line Connection is secured provided by screened double line ended by connector JACK 6 35 1 4 or XLR connector If you decide to connect sound signal connect connector AUDIO on back side of the device with yours audio output Keep next connection 1 2 3 1 signal 2 unconnecting 3 GND Connection DMX signal Ce ar Jack6 35 1 Datat 2 Data 3 GND XLR 1 GND 2 Data 3 Data NEVER connect DMX output with AUDIO input Function ofthe device USC 128 make possible o Controlling effects by protocol DMX 512 according to chosen configuration 8 channels 8effects 8 channels 16 effects or 16 channels 8 effects An ideal review about work of the controller LCD display 16x2 chars display an actual values X Y number of program and step actual time Setting up the text displaying when the device is switch on Calibration minimal and maximal values of X and Y Addressing functions of effects on chosen channels Setting up real time witch is on display Programming and making position of beam by joystick Buttons for your choice or setting Setting up single value offunctions by scrolling coil 10 built in programs 20 programs for an individual Progra
3. USC128 Universal DMX Controller Your distributor MANUAL Annotation choose general cleaning controller 1 Switch off controller 2 Switch on controller together with button SHIFT 6 for duration of 3 seconds 3 On a display is CLEAR ALL 4 Press BlackOut 5 for confirming choose Adisplay offer information about waiting 5 Approximately after 4 minutes light led SHIFT 6 After light led SHIFT controller is ready for the next using ATTENTION When you clear down the controller all programs definited by user clear 1 20 and controller configuration set on defaults parameters by producer Technical specification Supply voltage 230V 50Hz adapter Power consumption 12VA Fuse T100mA5x20mm Weight 2kg Dimensions mm 482x133x100mm Sound input 6 35 mono Jack 0 775V 60V 0 40dBm DMX output DMX 512 1990 4ms 6 35 stereo Jack Data Data OV XLR OV Data Data Memory capacity 8000 steps all programs iris USC 128 DMX512 Controller USER MANUAL Setthe time SPEED 8 of written step gt Write your choice by PAUSE SET 11 STORED will be displayed For the next step you adjust functions as a point 5 and press SHIFT 6 and LOCation tasses sit nine dt anne a ee dened eae PAUSE SET 11 it will cause notation chosen functions and write them as a last step Supply Voltage net ae de Rs pala eee tie of program E Power cord o Ifyour program was finishe
4. as they have been written The some program can be written in sequence several time After finishing of notation program sequence it starts make Programming in real time mode WRITE For forming your own programs programs 1 20 use route o Chose program for program notation see running programs o Press button WRITE EDIT 10 One display is WRITE SCANS Chose by button SC1 SC16 4 required projectors into MANUAL mode By repeated pressing WRITE EDIT 10 the notation will start During the notation on a display is step and you have possibility to chose single functions of projectors movement XY and time between steps For finishing notation press WRITE EDIT 10 If notation is over limit 130 or 260 steps notation will stop ona last step and will adjust PAUSE 11 gt oo O lt The number of steps is given by configuration channels see mode EDIT TIP If you have adjusted time between steps use button PAUSE SET 11 Before program notation you adjust scanners into basic position open iris colour gobo If you have chosen one of fixed programs 21 30 you don t have possibility of notation into this programs Programming mode EDIT Each program consist of steps The number of steps depends on configurated channel combination and projectors see configuration of the device Mode EDIT allows you return to written programs form them and create new one Programming Chose required program see r
5. d the movement between steps you make by STEP 12 POWETCONd NSRSRNSERNRNERnNnNnNnnnnnnnnnnnnnt and by STEP 13 you make necessary change point 5 and confirm by SET 11 Other important cautions ss Repeat from point 5 By buttons PROGRAM display L and WRITE EDIT you finished Maintenance sndeleanin EDIT mode OQ cane awaited eee ae tee TIP Good help during the notation is possibility of using default channel values see Service eer eee eee eee eee eee eee eee eee ee eee eee eee eee eee eee mn nn nn ee ere eee eee ey configuration of the device using default values UN Packing Shane Us St E ne ads beets dad shee A Shorten programs ine LEE ss acaba laa aes EE A anes Wats aah TEE ahs If you need short program which you have made you proceed Adjust program number for shorting press SHIFT 6 and WRITE EDIT 10 By STEP CONNCCHON 52 Mattei inte Ae iain ne tee MR a a de iat and STEP 12 chose step from which you want to short Press PROGRAM display L Connection tothe TAINS ait am nl An eme This way you short required step This operation can be applied on all editable programs 1 20 Connection to the controlsignal seeesssssesssrrresrsrrnsnsrsnnessrnnnessiennneannnns Attention Every natation have to be confirmed by SET Functions ofthe device ae ne den nn he Using default parameters USC 128 make possible Ne ne nr su nan Each scaner has for each channel DMX definite values of functions that are a
6. ectronic control of faulty operating Connection to the mains The device must always be connected behind the main switch Connection tothecontrol signal Each function of device is addressed according to standard protocol DMX 512 1990 4 1 programs step by step with adjusted speed You have possibility to chose of two AUDIO modes described in Description of the device by pressing button AUDIO PUL 13 On a display is chosen mode Program sequence If you want to form show of several programs you have to first form program sequence You form it this way Press button Shift 6 and then button PROGRAM 9 On a display is PGM STRING and first step of the program sequence Displayed chart L means that the program sequence is on a last step By scrolling coil you chose required program By button PAUSE SET 11 you will confirm it and on a display is STORED If was displayed L before step next step you form by choosing program and switching SHIFT and PAUSE SET On a display is COPIED and there will be formed next step of program sequence When you repeat this operation you will create whole program sequence If you want to change program number or to view program sequence use button STEP 12 and STEP 13 for moving in program sequence Program sequence you can short by button WRITE EDIT 10 all steps from displayed will be abolished Finishing you make by repeated pressing PROGRAM 9 button Programs are made in sequence
7. els by buttons CH1 CH16 by scrolling coil you address value as you want and confirm by SET 11 Function can be used in the case that you need to change colour by joystick X or Y set channel 3 This change will cause to that colours will be changing by movement of joystick If you want to continue in configuration press CONFIG 12 5 SELECT SETUP You set values of DMX channels for immediately choice function in manual mode or programming For example you set values for channel 3 for each colour etc Values set by producer you can immediately use for effects TwisterRotoScan and MercuryRotoScan Inthe case you need to change the values choose channel CH1 CH16 3 4 on a display will be name of channel number and value You set by coil value according to manual and confirm SET Exchange will be seen on effect Confirm SET 11 By button CONFIG you go through sequence of chosen channel channel can be consist of 8 set values By deactivation chosen channel and pressing CONFIG 12 you continue configuration 6 SET REAL TIME Setting real time By scrolling coil you set chosen value By button SET 11 you set hours minutes seconds If you want to continue in configuration press 4
8. ler USC 128 On a display is program number which is necessary to set before UPLOAD and step number For correct transmitting data it is necessary make following setouscanners channels SC1 SC16 4 to RUN mode inthe case the BLACK OUT 5 is switch on you switch off it you confirm by SET 11 Now the controller will transmit data to the next controller USC 128 After transmitting the selection UPLOAD is finish Modulation DMX channels The data transmission makes possible transmit copy only chosen channel DMX The method is identical with DOWNLOAD with this different that channels SC1 SC16 4 set up to mode MANUAL and on the channels which you want to rewrite you will do change The chosen channel will be rewritten other channels will stay ATTENTION Connect controller USC 128 through DMX OUT after choosing of function DOWNLOAD UPLOAD Running programs After switching controller it displaies adjusted banner for 3sc adjusts BlackOut 5 all projectors SC1 SC 16 4 to RUN mode and program 1 In case of forming program sequence with program 1 it runs Press button PROGRAM 5 LED lights and by scrolling coil you chose required program Deactive program LED don t light Deactive BlackOut LED don tlight If chosen program wasn t empty it starts making Change of speed running program and its mode By activation SPEED 8 LED lights on a display is the text SPEED and its actual adjusting By scrolling coil
9. lways in scaner manual Special functions E A E E E A a qu a a rar ae HET D D aha a For example scaner MercuryRotoScan has channel 3 colour definite values 0 white 16 blow 32 red etc They are definite with help configuration of controller SELECT SETUP The function Work With USO 128 milincr dct nb rend actuals becca lige terre uses for immediate changing function of scaner for example change colour gobo Configuration Of the device ists nec dt Un Min er Annee strobo etc It is possible to use manual change of function by choosing channel CH1 ase CH16 3 4 and by scroll coil but this change is slow and difficult on precision of choice Possibilities of regulating device ececceecccececeeeeeeeeeeeeeeeeeeteteeeeeeeeees Using this function we will explain on MANUAL mode but it is too very advisable for Modulation DMX channels other application program notice etc Description of the device ooo eee ceeecceceeeceeeeceeceeeeeeeeeeeteneeaeeaeeeeeeteneees 4 By buttons SC1 SC16 4 Set necdesanySeanerstomianualmeds RUNNING Programs 452 Hi ea pee Eten eden an RE 2 Address location of beam XY Change of speed during movement and its mode eceeeeeeeeeees 3 Press SELECT 4 By pressing CH1 CH16 3 4 button choose channel 5 By buttons SC1 SC8 4 choose desired channel value This value will be on a display Programming programs in real time mode WRITE e ee 6 Change display at once on scaner Prog
10. mming Programming in real time editation programs Set up for each effect four functions manual hold blackout run BlackOut Pause Mode ofwork automat manual audio 1 audio 2 gt oO Oo OOO Oo gt lt Special functions o Moving data from PC to controller there is necessary special software for programming free programs Copping programs between two controllers makes possible during copy selection of scanner channels and each other modul DMX channels during copping Ordered programs 7 8 9 10 11 12 13 14 T yr X 152 Y 130 P30 ww COLOR 152 098 M A 2 an 2 3 1 6 4 5 15 29 M DISPLAY LCD 16x2 chars shows you informations about your activity Display value X Y set up program or DMX channel made step realtime P2I VALUE SCROLL rolling coil for setting required values It uses for program selection DMX values speed 13 4 CH1 CH16 buttons for selection DMX channels colour gobo roto strobo etc buttons are activated by Shift 4 C1 SC16 buttons for selection effects buttons SC9 SC16 are activated by Shift 5 BlackOut button for black out effects 6 Shift button for activation multifunction buttons Connection with CH9 CH16 4 actives channels 9 to 16 with SC9 SC16 4 actives scanners 9 to 16 with PROGRAM 9 actives program sequence with WRITE EDIT 10 actives write of programs step by ste
11. nd after sound impulse send DMX signal 14 Power button 15 JOYSTICK is instrumental to move of the beam in axis X Y DMX system is a digital system by which are moved all informations between individual devices through one cable system IN OUT Abstractedly you can control by DMX signal a lot of devices The device connected to DMX signal have to be addressed and this address determine which informations from DMX will be addressed exactly to her DMX system needs for its activity special cables because frequency of transmit is about 12 times higher then audio frequency has with characteristic impedance 120 ohm We don trecommend to use longer cable then 250m Work with USC128 When you switch on controller it is in BlackOut and it has all DMX channels active in 3 mode Run Ondisplay are informations about axis X Y program number its step and realtime Before you use controller for the first time we recommend to set up parameters and functions of controller watch controller configuration Controller configuration You active controller configuration by button CONFIG The movement in configuration is by button CONFIG you are moving between possibilities of setting by scrolling coil you can change regulating and choose value as you need by SET you save chosen value you repeat from point 1 to the time displaying values which it display when you switch on the controller gt oo lt Possibilities
12. of controller setting 1 CONFIGURATION Amount channels and amount effects for control By coil you sett up value confirm it by button SET 11 Variants are 8 channels 8 scaners 16ch 8sc 8ch 16sc When you change the variant from 8ch 8sc to 16ch 8sc or 8ch 16sc or on the contrary on display is the text CHANGE DAMAGE PROGRAMS Y N You will make change by button BLACK OUT 5 Warning This change will cause change the programs you have set With variant 8ch 8sc you can program 260 steps with variant 16ch 8sc or 8ch 16sc you can program only a half 130 steps If you want to continue in configuration press CONFIG 12 2 ENTER BANNER You enter you personally greeting which will be displayed when you switch on the controller By the coil you change chars by SET 11 you confirm chosen char and move to the right If you want to continue configuration press CONFIG 12 3 CALIBRATION XY Set your joystick to the left border min X confirm SET 11 the same way you set right border max X interior border min Y top border max Y 4 ASSIGN CHANNEL Assignment channels reprogramming DMX channels Each function colour gobo has addressed DMX channel Set point by producer are X channel 1 Y channel 2 colour channel 3 rotogobo channel 4 channel for rotating gobos 5 iris channel 6 dimmer strobo channel 7 effects channel for prism effect 8 In condition that you use scaners technic with other setting choose chann
13. p with PAUSE SET you confirm data during programming Always we use it on general reset ITI SELECT button for right selection set value of DMX channel It uses in connection with chosen channel colour gobo etc The main application has in manual mode and programming when is necessary directly change of colours gobo etc For example in manual mode you select CH3 colour 3 press SELECT 7 and by buttons SC1 SC8 4 you select colours according to configuration you have programmed 8 SPEED button for time selection between steps witch are go on value is selected by coil Selected value by producer is 0 10 sec 19 PROGRAM button for choice of programming program choice is made by coil Program sequence you make by Shift 10 WRITE EDIT button for programming WRITE in real time EDIT with Shift step by step 111 PAUSE SET button for pause and confirming your choice During program it works as apause Otherwise for confirming and saving your choice 12 CONFIG button by witch you can set device number of channels and scanners to set the text you see at the begin calibration of joystick channels scheduling to set defaulted values DMX channels realtime sending and receiving data 113 AUDIO PUL button for choice mode of device you have possibilities to choice audio mode or automat according to select speed after receiving of the sound impulse smode AUDIO 1 make program step by step In the mode AUDIO 2 program goes on a
14. ramehalning aramona ent et Nada ed de Programming programs mode EDIT ceeeeeeeeeeeseeeeeeeeeeeeneeeeeeeennaeeees Defaults parameters ate set by producer for immediate using with effects Mercury RotoScan and TwisterRotoScan ATTENTION All operations coupled with editation defaults parameters and notation Shorting written programs nnes ai ia have to be make when BlackOut 5 is switch off and minimal one scaner is in manual Using changed parameters mode Saving values of real time is about 7 days than time set 00 00 All others informations will stay Controller clear down RESET TECHNIC informations 844 israel ile hhati a ao aaa aai In the case that you need to clear all programs and you want set values by producer you 7 Programming procedure eee eeeceeeee teen eee eeecneee eee teeeeeeeeeneeeeesineeeeees Resetofihe CEVICE ET et tte CMD ER 2 Gene Location Don t install the device at places with mechanical shakings and vibrations high dustiness or high temperature Not keeping these conditions can lead to shorter lifetime or its damage DON T expose the device to influence of water rain or moisture It could lead to electric shock or fire Ventilation It is necessary to ensure fans against their covering and secure the devices to have admission of air SUPPLY voltage Don t use any other supply voltage meant in technical specification and manufacture label Not keeping proper supply voltage could lead
15. unning programs o Press the button SHIFT 6 and WRITE EDIT 10 Ona display is EDIT SCANS Chose MANUAL mode on required projectors for notation o Ifthe program was empty or was last on a display is L Onarequired step you chose position of the beam next functions colour roto strobo 6 CONFIG 12 You ave just finished configuration of the device Special functions 7 DOWNLOAD PGM It si for receiving data from other device USC 128 On a display is number of program which you have to set before pressing DOWNLOAD and number of steps For correct receiving of data it is necessary make following you choose program to which have to be data written Itis possible rewrite only 1 20 programs scaner channels SC1 SC16 4 to which have to be data written set to HOLD mode Inthe case that BLACK OUT is switch on 5 you switch off youconfirm your choice by SET 11 This controller is not respond to buttons except power button 14 itis displaying bellow number of chosen program 535 and is waiting on data of the other controller USC 128 In the case that next controller is set on UPLOAD PGM and you have interconnected controllers DMX by cable in connectors DMX OUT and you have confirmed data transfer by button SET 11 look UPLOAD on the display is just transferring step of program After finishing transfer the program will set up pause 8 UPLOAD PGM It is for transmitting of data to the next control
Download Pdf Manuals
Related Search