Granit GB400 Battery Energizer GB400
Contents
1. Warranty Card Terms of Warranty User manual english version C Granit GB400 Battery Energizer GB400 we issue warranty for a period of Order No 580580102 3 years at following conditions We issue warranty to your energizer GB400 for a period of 3 years from date of selling at following conditions The selling date has to be proved by this certificate of guarantee which has to be accurately completed by your dealer All deficiencies or damages during this period that can be traced back to faults of material or faults of fabrication will be repaired costless when the device is returned to us prepaid This warranty cannot be issued when the device is being connected to wrong power supply or when it was damaged due to an Act of God e g lightning stroke or water damage It also cannot be issued in any case of unauthorized intervention or maloperation Device Battery Energizer Granit GB400 Selling date Serial number Packing unit 1 battery energizer GB400 1 grounding rod with bracket 1 fence and grounding cable 1 warning plate 1 dry battery 9V 55Ah 1 user manual and warranty card GRANIT QUALITY PARTS p65 Dealer stamp signature of dealer To execute repair works please contact your local GRANIT dealer GRANIT QUALITY PARTS 86073C_BAL_GB400_GRANIT_ENGLISCH Technical informations The battery energizer GB400 is powered by one 9V dry battery Two levels of output power strong extra2. ld up your fence solidly Avoid your animals from getting tangled in your electric fence O Check the condition of your fence and your energizer daily O Full performance of your energizer GB400 is achieved by using good isolated fences without fouling O Take care of a good grounding condition O Do not run your energizer GB400 with electric power supplies which are directly connected to mains supply
3. not blink a faulty fence an empty battery or a damaged energizer e g damaged by lightning stroke could be a reason To locate this please check the condition of the battery first If the battery is in good order then turn off the energizer and disconnect the fence screw 1 Now turn on the energizer again If the fence control lamp lights now check your fence If the fence control lamp still does not light then probably the energizer is damaged In this case contact your local dealer With the power selector 6 you can change power output from strong to extra strong Select extra strong at difficult tending conditions and longer fences Select strong to save battery power using the energizer with normal tending conditions and short battery control 4 fences If the battery control meter signs red ON OFF switch 5 then change the battery immediately Using power selector 6 a low battery means that output power may be low and therefore the energizer cannot provide for tending safety fence control 3 Safety informations Not following the safety instructions and an incorrect energizer setup could lead to hazard and may cause technical malfunction of the energizer Please observe strictly following items O Always use proper fencing material when using flexible fencing wire Wire of low quality is not recommended O Your energizer GB400 can also be used for tending sensitive animals O Bui
4. strong can be selected Power consumption is hereby reduced to gain maximum battery life depending on the required impulse power In built controls for fence and battery give best overview to all operating conditions fence fence tonnector ground operating voltage 9V power level strong extra strong load energy app 0 25J app 0 4J impulse energy app 0 2J app 0 3J current consumption app 16mA app 21mA off load voltage app 6500V app 7500V with animal touching app 2800V app 3500V at load 500 Ohm app 1200V app 1500V ground theor length of fence 6km 7km recommended length 1 3km 2 5km operating duration grounding rod with 9V 55Ah battery app 4 months app 3 months 2 Setting up To remove and change the battery please remove the screws 1 at both sides of the energizer then pull the handle upwards and lift the whole top Put in the new battery and connect the battery wires red and black to the supply pins and of the energizer Hit the grounding rod 2 deeply into the ground at a humid place directly nearby your fence Place your GB400 onto the grounding rod Connect the grounding rod 2 with the blue earthing cable to the ground connector of your energizer Connect your fence and the fence connector of your energizer using the fencing cable Turn on your GB400 using the on off switch With each fence impulse the fence control lamp 3 lights up If the fence control 3 does
Download Pdf Manuals
Related Search